Hybrid silica-organic material with immobilized amino groups: surface probing and use for electrochemical determination of nitrite ions

A sol–gel based hybrid process was developed by manipulating different techniques in sol–gel process to synthesize γ-alumina and (CuO, CuO + ZnO) doped γ-alumina spherical particles. Catalysts having spherical geometry have an important advantage over powders or pellets which are impervious to fluids, when packed in a reactor. Boehmite sol was used as alumina precursor for synthesizing porous γ-alumina and doped materials. γ-alumina particles having 5 wt% CuO, 4 wt% CuO + 1 wt% ZnO, 3 wt% CuO + 2 wt% ZnO and 2 wt% CuO + 3 wt% ZnO were prepared by adding required amounts of Cu(NO₃)₂ and Zn(NO₃)₂ solutions prior to gelation of the sol. Methanol dehydration studies were carried out by employing these synthesized catalysts. Hundred percent conversion of methanol to dimethyl ether was observed with (4 wt% CuO + 1 wt% ZnO)-γ-alumina and (5 wt% CuO)-γ-alumina microspheres at 325 and 350 °C, respectively.     

Synthesis of anatase TiO2 in a vinyl-containing ionic liquid and its enhanced photocatalytic activity

TiO₂ microspheres were synthesized by the sol–gel method using the ionic liquid (IL) 1-vinyl-3-propylimidazolium iodide (VPIM⁺I^?) as a reaction medium, then calcined at 500 °C. The samples were characterized by X-ray diffraction, scanning electron microscopy, and ultraviolet–visible (UV–Vis) diffuse reflectance spectroscopy. The phase of TiO₂ microspheres is anatase, and VPIM⁺I^? is able to favor the growth of anatase phase and prevents the collapse of small pores. The photocatalytic activity of TiO₂-IL was tested by degradation of 2-nitrophenol under UV light illumination. The photocatalytic activity of TiO₂-IL was higher than that of samples prepared in the reaction medium without VPIM⁺I^?.     

Enhanced zinc ion transport in gel polymer electrolyte: effect of nano-sized ZnO dispersion

The effect of the dispersion of zinc oxide (ZnO) nanoparticles in the zinc ion conducting gel polymer electrolyte is studied. Changes in the morphology/structure of the gel polymer electrolyte with the introduction of ZnO particles are distinctly observed using X-ray diffraction and scanning electron microscopy. The nanocomposites offer ionic conductivity values of >10^?3 S cm^?1 with good thermal and electrochemical stabilities. The variation of ionic conductivity with temperature follows the Vogel–Tamman–Fulcher behavior. AC impedance spectroscopy, cyclic voltammetry, and transport number measurements have confirmed Zn²⁺ ion conduction in the gel nanocomposites. An electrochemical stability window from ?2.25 to 2.25 V was obtained from voltammetric studies of nanocomposite films. The cationic (i.e., Zn²⁺ ion) transport number (t ₊) has been found to be significantly enhanced up to a maximum of 0.55 for the dispersion of 10 wt.% ZnO nanoparticles, indicating substantial enhancement in Zn²⁺ ion conductivity. The gel polymer electrolyte nanocomposite films with enhanced Zn²⁺ ion conductivity are useful as separators and electrolytes in Zn rechargeable batteries and other electrochemical applications.     

Optical, mechanical, and dielectric properties of Bi1/2Na1/2TiO3 thin film synthesized by sol–gel method

The Bi_1/2Na_1/2TiO₃ (BNT) thin film has been researched as an excellent candidate of lead-free ferroelectric materials. We synthesized BNT thin film on Si wafers or quartz glass by sol–gel spin coating method. The homogeneous and crack-free BNT thin film was synthesized by cost effective solution sol gel coating method. The main crystal phase of the film was identified as Bi_1/2Na_1/2TiO₃. The BNT thin film which was coated 3 times and heat-treated at 700 °C had about 70% of transmittance in the ultra-violet visible (UV–VIS) light wavelength region. The calculated band gap energies from the UV transmittance spectra were 3.0 and 3.5 eV for indirect and direct transition, respectively and the refractive index of BNT thin film was 2.16 at 898 nm of wavelength. The hardness and elastic modulus of the film were about 9 and 136 GPa at 10 mN load, where the penetration depth was about 220 nm. BNT thin film showed the diffuse type of dielectric properties due to its Na⁺ and Bi³⁺ ions in A′_1/2A″_1/2BO₃-type perovskite structure and the dielectric constant was about 10 until 300 °C and showed maximum value at 550 °C, 450 at 1 kHz.     

Preparation of CuCrO2 nanoparticles with narrow size distribution by sol–gel method

Copper chromium oxide (CuCrO₂) nanoparticles were synthesized by sol–gel method. The effect of annealing temperature, duration of heat treatment and metallic ion concentration in precursor solution on the structural properties of the nanoparticles was investigated. The delafossite structure of CuCrO₂ powder was confirmed by X-ray diffractometer. It was found that the crystallite sizes as well as the size of the nanoparticles increased with annealing temperature and duration of heat treatment but decreased with metallic ion concentration. Nanoparticles’ size was obtained using particle size analyzer. The synthesized CuCrO₂ nanoparticles with 0.7 M metallic ion concentration have the lowest crystallite and particle sizes with a narrow size distribution in the range of 13.5–15.6 nm. In the presence of this metallic ion concentration, we could also produce single crystal CuCrO₂ nanoparticles. Moreover, the CuCrO₂ nanoparticles exhibit a large optical band gap that increases with metallic ion concentration. The optical band gap of the nanoparticles fabricated with 0.7 M metallic ion concentration in precursor solution is about 3.99 eV.     

Sol–gel synthesis of Sm2InTaO7 and its photocatalytic activity on degradation of crystal violet dye and reduction of Cr(VI) ions

This paper reports the synthesis of Sm₂InTaO₇ and its photocatalytic activity on the degradation of crystal violet dye and reduction of Cr(VI) ions in aqueous solution. Sm₂InTaO₇ was prepared by sol–gel method at 1,200 °C. For comparison purposes, Sm₂InTaO₇ was prepared also by solid-state reaction at 1,400 °C. The evolution of the crystalline phases of the sol–gel sample with the annealing temperature was followed by X-ray diffraction. The cubic crystalline structure of Sm₂InTaO₇ was determined by Rietveld refinement method. Specific surface area was 5 m²g^?1 for sol–gel sample and 1 m²g^?1 for solid-state sample, whereas energy band gap was around 3.5 eV. Sm₂InTaO₇ prepared by sol–gel method showed better photocatalytic activity than Sm₂InTaO₇ prepared by solid-state reaction for the mineralization of crystal violet dye and reduction of Cr(VI) solution under UV-light irradiation.     

Synthesis of Li3Ni x V2−x (PO4)3/C cathode materials and their electrochemical performance for lithium ion batteries

Li₃Ni _x V_2?x (PO₄)₃/C (x?=?0, 0.02, 0.04 and 0.06) samples have been synthesized via an improved sol–gel method. X-ray diffraction patterns indicate that the structure of the prepared samples retains monoclinic, and the single phase has not been changed with Ni doping. From the analysis of electrochemical performance, the Li₃Ni_0.04?V_1.96(PO₄)₃/C sample exhibits the best electrochemical property. It delivers a discharge capacity of 112.1 mAh?g^?1 with capacity retention of 95.2 % over 300 cycles at 10 C rate in the range of 3.0–4.8 V; cyclic voltammetry and electrochemical impedance spectra testing further prove that the electrochemical reversibility and lithium ion diffusion behavior of Li₃V₂(PO₄)₃ have also been effectively improved through Ni doping.     

Sol–gel synthesis,optical and structural characterization of ZrOS nanopowder

In this paper, we report the synthesis of tetragonal zirconium oxysulfide t-ZrOS nanopowder by the sol–gel method using water solution of a precursor containing thiourea [CS(NH₂)₂] and zirconium in the form of an anionic oxalate complex [Zr(C₂O₄)]^4?. The tetragonal t-ZrOS structure with space group P4/nmm revealed by X-ray patterns showed preferred orientation along (101) plane. For surface morphology, compositional and optical absorption studies, scanning electron microscopy, energy dispersive X-ray and ultraviolet–visible spectroscopy were employed for characterization of the powder respectively. A nearly constant value of the refractive index at higher wavelength λ ≥ 1,100 nm was found to be 2.19. High indirect and direct optical band gap of ~2.0 and 2.50 eV with absorbance <40 % were obtained for the powder.     

Nanocrystalline Zn1−x−yBexMgyO thin films synthesized by the sol–gel method: structural and near infrared photoluminescence properties

In this paper, we reports on the structural and optical properties of Zn_1?x?yBe_xMg_yO thin films prepared by sol–gel method, which are new materials for optoelectronic and ultraviolet-light-emitting devices. The crystal structure and core level spectra of these films are studied by X-ray diffraction and X-ray photoelectron spectroscopy. Surface morphology of the films is analyzed by scanning electron microscope images and the surface is composed of spherical shaped grains. Micro-photoluminescence shows a near edge band emission and the peak values tuned from 3.26 eV for the undoped to 3.4 eV for the doped ZnO film. Near infrared emission is observed in the region 1.64–1.67 eV for pure and co-doped ZnO films. In micro-Raman spectra, multiple-order Raman bands originating from ZnO-like longitudinal optical (LO) phonons are observed. A Raman shift of about 5–18 cm^?1 is observed for the first-order LO phonon. A comparative study was made on Raman band for BeZnO, MgZnO and BeMgZnO nanocrystals with the LO phonon band of bulk ZnO. The ultraviolet resonant Raman excitation at room temperature shows multi-phonon LO modes up to the fourth order. Deformation energy of all the films is calculated and BeMgZnO film has the minimum deformation energy.     

Modifications in band gap and optical properties of Zn0.96−xNd0.04CuxO (x = 0, 0.05, 0.1 and 0.15) nanoparticles

Nd-doped and Nd, Cu co-doped ZnO nanoparticles (Zn_0.96?xNd_0.04Cu_xO, x = 0, 0.05, 0.1 and 0.15) were synthesized by sol–gel method. The structural and optical properties of the samples were investigated by X-ray diffraction (XRD) and UV–visible photo-spectrometer. The synthesized nanoparticles have different microstructure without changing a hexagonal wurtzite structure. CuO phase was noticed in XRD spectra at 38.73° after Cu = 5 % which was formed from remaining un-reacted Cu²⁺ ions. The average crystal size was gradually increased from Cu = 0 % (17 nm) to 15 % (17.6 nm) having lowest value (16.7 nm) at Cu = 5 %. The change in lattice parameters confirmed the substitution of Cu in Zn–Nd–O lattice. The observed constant c/a ratio revealed that there was no change in hexagonal wurtzite structure by Cu-doping. The energy dispersive X-ray spectra confirmed the presence of appropriate amount of Nd and Cu in Zn–O lattice. The optical absorption was increased gradually from Cu = 0–10 % and showed maximum at Cu = 10 % due to the presence of more nucleation centres and defect states. The defects related green band between 487 and 493 nm was due to the oxygen vacancies and intrinsic defects. The higher transmittance (≈ 90 %) noticed at Cu = 15 % leads to the industrial applications. The observed blue shift in energy gap from 3.49 eV (Cu = 0 %) to 3.65 eV (Cu = 10 %) and the red shift from Cu = 10 % (3.65 eV) to Cu = 15 % (3.61 eV) can be explained by the Burstein–Moss effect. Presence of chemical bonding was confirmed by Fourier transform infrared spectra.     

An investigation of Zn/ZnO:Al/p-Si/Al heterojunction diode by sol–gel spin coating technique

Present study shows the structural, morphological, optical characterization of sol–gel spin coated ZnO:Al film and investigation of device efficiency of Zn/ZnO:Al/p-Si/Al heterojunction diode structure. X-ray diffraction study indicates that film has hexagonal polycrystalline structure with (002) preferential direction. Atomic force microscope and scanning electron microscope images exhibit that surface of ZnO:Al/p-Si consists of homogenously scattered nanoparticles. The surface roughness of ZnO:Al film is found to be 15.24 nm. The band gap value of ZnO:Al film deposited on glass substrate is calculated to be 3.34 eV. The electrical characterization of Zn/ZnO:Al/p-Si/Al heterojunction structure is made by current–voltage (I–V) and capacitance–voltage (C–V) measurements. From these measurements, the heterojunction structure shows a rectifying behavior under a dark condition. The ideality factor and barrier height of Zn/n-ZnO:Al/p-Si/Al structure are calculated as 3.23 and 0.68 eV. The heterojunction structure have diode characteristic with rectification ratio at 64.4 at +2.0 V in the dark. The results suggest that Zn/ZnO:Al/p-Si/Al heterojunction diode can be successfully used in many optoelectronic applications.     

Synthesis,characterization, crystal structure,electrochemical properties and electrocatalytic activity of an unexpected nickel(II) Schiff base complex derived from bis(acetylacetonato)nickel(II), acetone and ethylenediamine

The synthesis, crystal structure and electrochemical properties of a Ni(II) Schiff base complex, [Ni(L)]PF₆ (where L is 2,4,9,11,11-pentamethyl-2,3,4 triaza-1-one-4-amine) are reported herein. The complex has been characterized by its electrochemical behavior, X-ray crystallographic structural analysis, physio-chemical methods and spectroscopic techniques. Electrospray mass spectroscopic analysis gives a dominant ion peak with m/z = 296 which corresponds to the {[Ni(L)]PF₆–HPF₆}⁺ fragment. Cyclic voltammograms for [Ni(L)]PF₆, obtained in DMF (0.1 M Bu₄NPF₆) at a glassy carbon electrode with a scan rate of 100 mV s^?1, exhibit reversible ([Ni^II(L)]⁺/[Ni^I(L)]) reduction and chemically irreversible ([Ni^II(L)]⁺/[Ni^III(L)]²⁺→ electroactive product) oxidation processes at ?2.05 and 0.62 V, respectively. The diffusion coefficient, calculated using the Randles–Sevcik relationship, is 9.7 × 10^?6 cm² s^?1. Electrochemical studies reveal that the Ni^I reduced form of the complex is capable of catalyzing CO₂ reduction at a potential that is thermodynamically more favorable than for the reduced [Ni(N,N′-ethylenebis(acetylacetoneiminato)]complex. Spectroelectrochemical analyses following bulk electrolysis of [Ni(L)]PF₆ under CO₂ revealed the formation of oxalate and bicarbonate.     

Synthesis, Spectral, Thermal and CO2 Absorption Studies on Birnessites Type Layered MnO6 Oxide

Birnessite type layered MnO₆ oxides with increased crystallinity were synthesized from six carbohydrates and three dihydric phenols viz., dextrose, starch, fructose, galactose, maltose, lactose, catechol, resorcinol, quinol and KMnO₄ through the formation of a sol–gel. All of the MnO₆ oxides were characterized by powder XRD. The strong signal at 2θ ~ 12° corresponding to 7.4 Å refers to the Mn–Mn distance between the adjacent layers. The interlayer volume is dispersed with K⁺ ions and H₂O molecules. The presence of interlayer K⁺ ions is indicated by a signal at 25°, corresponding to a distance of 3.5 Å. IR spectra of the oxides show signature bands at ca. 500 cm^?1 due to the stretching modes occurring for MnO₆ entity. A broad band observed at ca. 3300 cm^?1 is due to interlayer water molecules. Thermal analysis indicated three stage decomposition with the formation of MnO₂ at ca. 600 °C through the intermediate formation of Mn(OH) _n . The MnO₆ exhibited a remarkable CO₂ scrubbing ability, which has also been investigated.     

Influence of annealing temperature on the electrochemical and surface properties of the 5-V spinel cathode material LiCr0.2Ni0.4Mn1.4O4 synthesized by a sol–gel technique

LiCr_0.2Ni_0.4Mn_1.4O₄ was synthesized by a sol–gel technique in which tartaric acid was used as oxide precursor. The synthesized powder was annealed at five different temperatures from 600 to 1,000 °C and tested as a 5-V cathode material in Li-ion batteries. The study shows that annealing at higher temperatures resulted in improved electrochemical performance, increased particle size, and a differentiated surface composition. Spinel powders synthesized at 900 °C had initial discharge capacities close to 130 mAh g^?1 at C and C/2 discharge rates. Powders synthesized at 1,000 °C showed capacity retention values higher than 85 % at C/2, C, and 2C rates at 25 °C after 50 cycles. Annealing at 600–800 °C resulted in formation of spinel particles smaller than 200 nm, while almost micron-sized particles were obtained at 900–1,000 °C. Chromium deficiency was detected at the surface of the active materials annealed at low temperatures. The XPS results indicate presence of Cr⁶⁺ impurity when the annealing temperature was not high enough. The study revealed that increased annealing temperature is beneficial for both improved electrochemical performance of LiCr_0.2Ni_0.4Mn_1.4O₄ and for avoiding formation of Cr⁶⁺ impurity on its surface.     

Transparent conductive tungsten-doped tin oxide thin films synthesized by sol–gel technique on quartz glass substrates

Transparent conductive tungsten-doped tin oxide (SnO₂:W) thin films were synthesized on quartz glass substrates by sol–gel dip-coating method. It was found that the films were highly transparent and the average optical transmission was about 90% in the visible and near infrared region from 400 to 2,500 nm. The optical band gap is about 4.1 eV. The lowest resistivity of 5.8 × 10^?3 ohm cm was obtained, with the carrier mobility of 14.2 cm² V^?1 s^?1 and carrier concentration of 7.6 × 10¹⁹ cm^?3 in 3 at.% W-doping films annealed at 850 °C in air. The structural properties, surface morphology and chemical states for the films were investigated.     

Li<Superscript>+</Superscript> ionic conduction properties on NaI doped with a small amount of LiBH<Subscript>4</Subscript>

In the present work, Li⁺ conductor is synthesized via small doping of LiBH₄ into “Li-free” compound (or solid solvent), NaI. The formation of solid solution between NaI and LiBH₄ is confirmed by XRD measurement, and the solubility limit of LiBH₄ exists between 6 to 13 mol%. The value of σ for 15NaI·LiBH₄ (6 mol% LiBH₄) showed 1.7 × 10^?6 S/cm at room temperature, which is comparable to that for LiI. From the plot of log σT vs. 1000/T, an activation energy for Li⁺ conduction in NaI is estimated to be 0.68 and 0.32 eV for heating and cooling cycle, respectively. The results of AC impedance measurement and DC polarization test indicate that Li⁺ plays a major role in ionic conduction in NaI regardless of the slight molar fraction of Li⁺. The present results suggest that the expansion in the material choice for solid solvent and other alkali halides can also work as a base material for Li⁺ ion conductors.     

Preparation and characterization of In2O3/ZnO heterostructured microbelts by sol–gel combined with electrospinning method

Long and thin In₂O₃/ZnO heterostructured microbelts were synthesized by sol–gel combined with electrospinning process. The as-prepared microbelts show the well defined one-dimensional belt structures with 1–5 μm in width and tens of millimeters in length. The polycrystalline microbelts calcined at 973 K for 1 h are still continuous and have the uniform rectangular cross sections and the thickness to width ratio is around 1:10. The crystalline phases of samples are investigated by X-ray diffraction and the morphology is examined using transmission electron microscope and scanning electron microscope. In₂O₃/ZnO heterostructured microbelts exhibit the excellent visible photocatalytic property in the photodegradation of methyl orange (MO), and over 94 % of MO was degraded within 3 h.     

The properties of nickel aluminate nanoparticles prepared by sol–gel and impregnation methods

Nickel aluminates were prepared by sol–gel and impregnation methods and calcined at 1100 °C. The sol–gel made samples were prepared with different amounts of nickel (Ni/Al molar ratio equal to 0, 0.25, 0.5, and 0.75) and aging times (24 and 48 h). The samples were characterized by X-ray diffraction, induced couple plasma, nitrogen physisorption, transmission and scanning electron microscopy, and ammonia temperature programmed desorption (NH₃-TPD). In the sol–gel made samples, only the NiAl₂O₄ structure of nickel aluminate was defined, while for impregnation, NiAl₁₀O₁₆ was formed as well. The sol–gel made samples had low specific surface areas (7.7–12.4 m²/g), but a sample prepared by impregnation method had higher specific surface area (67.2 m²/g). The surface acidity density decreased by increasing the amount of nickel and was the lowest for impregnation method.     

Switchable Spherical-Wormlike Micelle Transition in Sodium Oleate/N-(3-(Dimethylamino)propyl)-Octanamide Aqueous System Induced by Carbon Dioxide Stimuli and pH Regulation

The structure transitions of the aggregates in the sodium oleate (NaOA)/N-(3-(dimethylamino)propyl)-octanamide (DPOA) aqueous system was investigated upon CO₂ stimuli. During the process of bubbling of CO₂, three appearance states of sol, gel, and emulsion with little white precipitate were observed continuously. The cryo-transmission electron microscope characterization and rheological measurements exhibited that the sol–gel transition was attributed to a spherical-wormlike micelle transition. Moreover, this transition was switchable at least three cycles in the pH range of 10.91–9.56 by CO₂ stimuli and pH regulation (adding NaOH), which could be explained by the protonation of DPOA and deprotonation of DPOA · H⁺. Bubbling of CO₂ resulted in protonation of DPOA, which not only inserted into the OA^– as a co-surfactant but also screened the electrostatic repulsion among OA^–, corporately leading to the spherical-wormlike micelle transition. Adding NaOH caused the deprotonation of DPOA · H⁺ and hence reversed this transition. This surfactant system with switchable micelle transition not only displays tremendous application potential in various fields but also is of key importance in cyclic utilization of surfactant.     

Different morphologies of ZnO nanostructures via polymeric complex sol–gel method: synthesis and characterization

Various morphologies of ZnO nanostructures, such as nanoparticles, nanorods and nanoflowers have been achieved controllably by polymeric sol–gel method. In this approach, zinc nitrate Zn(NO₃)₂·6H₂O, citric acid and ethylene glycol were used as the source of Zn²⁺, the chelating agent and the solvent agent, respectively. The microstructure of the ZnO nanostructures was characterized by X-ray diffractometry, scanning electron microscopy with the energy dispersive X-ray spectroscopy, transmission electron microscopy, thermogravimetric analysis and Fourier transform infrared spectroscopy. The effect of ethylene glycol to citric acid mole ratio on the morphology and structure of the products was discussed. The ZnO nanoparticles with diameter between 24 ± 2 nm was obtained with EG:CA mole ratio equal to 2:1. The optical properties of as-obtained power were investigated by ultraviolet–visible spectroscopy.