Electrochemical sensor for parabens based on molecular imprinting polymers with dual-templates

A selective, sensitive, rapid and reliable method based on molecularly imprinted polymers (MIPs) with dual templates to determine total content of parabens in cosmetics was developed. With methylparaben (MP) and propylparaben (PP) as dual-templates, methacrylic acid (MAA) as a functional monomer and tripropylene glycol diacrylate (TPGDA) as a cross-linker, MIPs film on a glassy carbon electrode was constructed as paraben sensor. At oxidation potential of 0.94 V (vs. SCE), the peak currents on the MIPs sensor were proportional to the concentration of parabens with square wave voltammetry. As the ratio of MP to PP in the MIPs was 1:1.25, the regression equations for four parabens were almost the same. The linear range was 20-100 μM for MP and EP, 5-100 μM for PP, and 5-80 μM for BP, with detection limit of 0.4 μM for MP and EP, 0.2 μM for the others. The total content of parabens could be calculated according to the average of these four regress equations. At least 10 times of structural analogs, such as p-hydroxybenzoic acid, p-aminobenzoic acid and phenol would not interfere with the determination of parabens. Nonanalogous coexistences such as vitamin C had no response on the sensor at all. Rapid response of the MIPs sensor was obtained within 1 min. MIPs sensor had been used to determine total content of parabens in cosmetic samples with recoveries between 98.7% and 101.8%. It reveals that the MIPs sensor with multi-templates has a potential to determine the total content of a group of homologous compounds.     

Potentiometric stripping analysis of methyl and ethyl parathion employing carbon nanoparticles and halloysite nanoclay modified carbon paste electrode

Carbon nanoparticles (CNPs) and halloysite nanoclay (HNC) modified carbon paste electrode (HNC–CNP–CPE) was developed for the determination of methyl parathion (MP) and ethyl parathion (EP). The electrochemical behavior of these molecules was investigated employing cyclic voltammetry (CV), chronocoulometry (CC), electrochemical impedance spectroscopy (EIS) and potentiometric stripping analysis (PSA). After optimization of analytical conditions employing this electrode at pH 5.0 in acetate buffer (0.1 M), the peak currents were found to vary linearly with its concentration in the range of 1.55 × 10⁻⁹ to 3.67 × 10⁻⁶ M and 1.21 × 10⁻⁹ to 4.92 × 10⁻⁶ M for MP and EP, respectively. The detection limits (S/N = 3) of 4.70 × 10⁻¹⁰ M and 3.67 × 10⁻¹⁰ M were obtained for MP and EP, respectively, using PSA. The prepared modified electrode showed several advantages such as simple preparation method, high sensitivity, very low detection limits and excellent reproducibility. The proposed method was employed for the determination of MP and EP in fruits, vegetables, water and soil samples.     

Determination of 6-mercaptopurine based on the fluorescence enhancement of Au nanoparticles

A novel method for the determination of 6-mercaptopurine (6MP) has been developed based on fluorescence enhancement of Au nanoparticles (AuNPs). The fluorescent AuNPs with mean diameter of ∼15 nm were synthesized in aqueous solution, exhibiting the stable maximum emission at 367 nm, under the excitation at wavelength of 264 nm. The AuNPs self-assembly with 6MP were characterized with transmission electron microscopy (TEM), ultraviolet-visible (UV-vis) absorption, fluorescence and surface-enhanced Raman scattering (SERS) spectroscopy. The results revealed that the surface attachment through versatile binding sites of S10, N3, N9 and N7 atoms in 6MP produced the interparticle coupling and formed aggregates of AuNPs. As a result, the fluorescence emission enhancement was significantly observed upon AuNPs self-assembly with 6MP. The fluorimetric determination under optimal conditions indicated that 6MP could be quantified in good linearity range of 6.35 × 10⁻⁸ to 3.05 × 10⁻⁷ M, with a low detection limit of 4.82 × 10⁻¹⁰ M. The relative standard deviation (n = 11) was 1.8% at 2.54 × 10⁻⁸ M 6MP concentration level. The proposed method was successfully applied for the determination of 6MP in spiked human urine. The probable fluorescence enhancement mechanism was also discussed there.     

Organophosphorus insecticides extraction and heterogeneous oxidation on column for analysis with an acetylcholinesterase (AChE) biosensor

This paper presents an analysis method for organophosphorus insecticides based on AChE biosensors coupled with a preconcentration and oxidation on a solid phase column. Three organic solvents, acetonitrile (ACN), ethanol and methanol were tested for their influence on AChE activity, insecticide inhibition and their ability to elute the adsorbed insecticides. Our results showed that ACN in a concentration of 5% (v/v) had the less negative effect on biosensor analysis and was the most appropriate organic solvent for the column elution. The presence of the organic solvent in the incubation media of the biosensor was found to induce a reduction of the inhibition percentages. The inhibition of the biosensors was performed in phosphate buffer with 5% (v/v) ACN, while the initial and remaining response of the biosensors were measured in PBS. In these conditions, the LODs of paraoxon and dichlorvos were measured with or without a preconcentration step. The LODs of the AChE biosensor without sample preconcentration were 8 × 10⁻⁸ M for paraoxon and 1 × 10⁻⁷ M dichlorvos and the LOD obtained after the preconcentration step were 2.5 × 10⁻⁸ M for paraoxon and 2.5 × 10⁻⁸ M for dichlorvos. Moreover, the use of the column allowed the heterogeneous oxidation of organophosphorus insecticides for improved LOD.     

Electrodeposition of gold nanoclusters on overoxidized polypyrrole film modified glassy carbon electrode and its application for the simultaneous determination of epinephrine and uric acid under coexistence of ascorbic acid

A novel biosensor was fabricated by electrochemical deposition of gold nanoclusters on ultrathin overoxidized polypyrrole (PPyox) film, formed a nano-Au/PPyox composite on glassy carbon electrode (nano-Au/PPyox/GCE). The properties of the nanocomposite have been characterized by field emission scanning electron microscope (FE-SEM), X-ray photoelectron spectroscopy (XPS), powder X-ray diffraction (XRD) and electrochemical investigations. The nano-Au/PPyox/GCE had strongly catalytic activity toward the oxidation of epinephrine (EP), uric acid (UA) and ascorbic acid (AA), and resolved the overlapping voltammetric response of EP, UA and AA into three well-defined peaks with a large anodic peak difference. The catalytic peak currents obtained from differential pulse voltammetry increased linearly with increasing EP and UA concentrations in the range of 3.0 × 10⁻⁷ to 2.1 × 10⁻⁵ M and 5.0 × 10⁻⁸ to 2.8 × 10⁻⁵ M with a detection limit of 3.0 × 10⁻⁸ and 1.2 × 10⁻⁸ M (s/n = 3), respectively. The results showed that the modified electrode can selectively determine EP and UA in the coexistence of a large amount of AA. In addition, the sensor exhibited excellent sensitivity, selectivity and stability. The nano-Au/PPyox/GCE has been applied to determination of EP in epinephrine hydrochloride injection and UA in urine samples with satisfactory results.     

Indirect determination of cyanide ion and hydrogen cyanide by adsorptive stripping voltammetry at a mercury electrode

An indirect voltammetric method is described for determination of cyanide ions and hydrogen cyanide, using the effect of cyanide on cathodic adsorptive stripping peak height of Cu-adenine. The method is based on competitive Cu complex formation reaction between adenine at the electrode surface and CN⁻ ions in solution. Under the optimum experimental conditions (pH=6.42 Britton-Robinson buffer, 1×10⁻⁴ M copper and 8×10⁻⁷ M adenine), the linear decrease of the peak current of Cu-adenine was observed, when the cyanide concentration was increased from 5×10⁻⁸ to 8×10⁻⁷ M. The detection limit was obtained as 1×10⁻⁸ M for 60 s accumulation time. The relative standard deviations for six measurements were 4 and 2% for the cyanide concentrations of 5×10⁻⁸ and 2×10⁻⁷ M, respectively. The method was applied to the determination of cyanide in various industrial waste waters such as electroplating waste water and also for determination of hydrogen cyanide in air samples.     

Comparative study for the analysis of parabens by micellar electrokinetic capillary chromatography with and without large-volume sample stacking technique

The separation and determination of four parabens (methyl, ethyl, propyl, and butyl p-hydroxybenzoate) which are commonly used as preservatives in cosmetic products, by micellar electrokinetic capillary chromatography (MEKC) with and without large-volume sample stacking (LVSS) technique were compared. As an effective on-line concentration technique, LVSS was successfully combined with MEKC to determine neutral parabens in an acidic media. The effects of some typical parameters such as sample volume, buffer pH, temperature, and concentration of surfactant were examined. The detection limits for this LVSS-MEKC method were found to be 3.0 × 10⁻⁷ M for each of the parabens based on the signal-to-noise ratio of 3, which were around 300 times lower than normal MEKC technique. The curves of peak response versus concentration were linear from 1.0 × 10⁻⁶ to 5.0 × 10⁻⁵ M with regression coefficients of 0.9987, 0.9960, 0.9925 and 0.9864, respectively. A simple and easy-manipulative sample preparation method was developed and validated by analyzing commercially available cosmetic samples. It was found that with current sample preparation process and instrumentation system, 0.5 g of sample is enough for the analysis of parabens preservatives in cosmetic product with satisfactory results.     

Time measurement-visual analysis of l-cysteine using the autocatalytic sodium sulfite/hydrogen peroxide reaction system and its application to length detection-flow analysis

Trace amounts of l-cysteine can function as a trigger, i.e., reaction initiator, in the autocatalytic sodium sulfite/hydrogen peroxide reaction system. Rapidly changing of pH after induction time is visually confirmed by color changing of bromothymol blue in this autocatalytic reaction. Based on this finding, μg L⁻¹ levels of l-cysteine were measured over time using the autocatalytic reaction system. The determination range using the above method was 5.0 × 10⁻⁸-2.5 × 10⁻⁶ M, the detection limit (3σ) was 1.8 × 10⁻⁸ M (1.94 μg L⁻¹), and the relative standard deviation was 2.41% at an l-cysteine concentration of 5 × 10⁻⁷ M (n = 5). This method was also applied to length detection-flow injection analysis. The determination range for the flow injection analysis was 2.0 × 10⁻⁷-1.0 × 10⁻⁵ M. The detection limit (3σ) was 1.4 × 10⁻⁷ M (17.0 μg L⁻¹), and the relative standard deviation was 0.91% at an initial l-cysteine concentration of 10⁻⁶ M (n = 5).     

Simultaneous determination of epinephrine, uric acid and xanthine in the presence of ascorbic acid using an ultrathin polymer film of 5-amino-1,3,4-thiadiazole-2-thiol modified electrode

This paper describes the simultaneous determination of epinephrine (EP), uric acid (UA) and xanthine (XN) in the presence of ascorbic acid (AA) using electropolymerized ultrathin film of 5-amino-1,3,4-thiadiazole-2-thiol (p-ATT) modified glassy carbon (GC) electrode in 0.2 M phosphate buffer solution (pH 5). Although bare GC electrode resolves the voltammetric signals of AA and XN, it fails to resolve the voltammetric signals of EP and UA in a mixture. However, the p-ATT modified electrode not only separates the voltammetric signals of AA, EP, UA and XN with potential difference of 150, 120 and 400 mV between AA-EP, EP-UA and UA-XN, respectively but also shows higher oxidation current for these molecules. The p-ATT modified electrode exhibits excellent selectivity towards the oxidation of EP, UA and XN in the presence of 40-fold higher concentration of AA. Further, the p-ATT modified electrode was also used for the selective determination of EP in the presence of 40-fold higher concentrations of AA, UA and XN. Using amperometric method, we achieved the lowest detection of 40 nM EP and 60 nM each UA and XN. The amperometric current response was increased linearly with increasing EP concentration in the range of 4.0 × 10⁻⁸ to 4.0 × 10⁻⁵ M and the detection limit was found to be 27 × 10⁻¹¹ M (S/N = 3). The practical application of the present modified electrode was demonstrated by determining the concentration of EP in epinephrine tartrate injection and XN in human urine samples.     

Determination of gallium by adsorptive stripping voltammetry

A procedure for the determination of gallium by differential pulse adsorptive stripping voltammetry (DPADSV), using different complexing agents (ammonium pyrrolidine dithiocarbamate (APDC), pyrocatechol violet (PCV) and diethyldithiocarbamate (DDTC)), has been optimized. The selection of the experimental conditions was made using experimental design methodology. Under these conditions, the calibration was made and the detection limit was determined for each gallium-ligand complex. A robust regression method was applied which allowed the elimination of anomalous points. The detection limit, with α=β=0.05, for gallium-APDC complex was 5.0×10⁻⁸ mol dm⁻³, for gallium-PCV complex was 9.9×10⁻⁹ mol dm⁻³, and the lowest detection limit (1.3×10⁻⁹ mol dm⁻³) was obtained with DDTC. For this reason, DDTC was selected for the determination of the gallium concentration in a certificate sample and in a spiked tap water sample. The linear dynamic range for gallium-APDC complex was from 5.0×10⁻⁸ to 2.7×10⁻⁷ mol dm⁻³, for gallium-PCV complex was from 5.0×10⁻⁹ to 4.8×10⁻⁷ mol dm⁻³, and for gallium-DDTC complex was from 1.0×10⁻⁹ to 2.1×10⁻⁷ mol dm⁻³.     

Synthesis and analytical application of a novel tetradentate N(2)O(2) Schiff base as a chromogenic reagent for determination of nickel in some natural food samples

A novel sensitive chromogenic reagent, N,N′-bis(3-methylsalicylidene)-ortho-phenylene diamine (MSOPD), has been synthesized and used in the spectrophotometric determination of nickel. At pH 8, MSOPD can react with nickel ion at room temperature to form a 1:1 complex. The apparent molar absorptivity is 9.5 × 10⁴ l mol⁻¹ cm⁻¹ at 430 nm. Beer's low is obeyed over the range 0-1.0 × 10⁻⁵ M of nickel with a detection limit of 1.36 × 10⁻⁸ M. The relative standard deviation for measurement of 3.41 × 10⁻⁶ M nickel is 1.3% (n = 10). The method has successfully been applied to determination of trace amounts of nickel in some natural food samples.     

Ionic liquid-based miniature electrochemical sensors for the voltammetric determination of catecholamines

Screen-printed electrodes modified with carbon paste that consisted of graphite powder dispersed in ionic liquids (IL) were used for the electrochemical determination of dopamine, adrenaline and dobutamine in aqueous solutions by means of cyclic voltammetry. The IL plays a dual role in modifying compositions, acting both as a binder and chemical modifier (ion-exchanger); ion-exchange analyte pre-concentration increases analytical signal and improves the sensitivity. Calibration graphs are linear in concentration range 3.9 × 10⁻⁶ to 1.0 × 10⁻⁴ M (dopamine), 2.9 × 10⁻⁷ to 1.0 × 10⁻⁴ M (adrenaline) and 1.7 × 10⁻⁷ to 1.0 × 10⁻⁴ M (dobutamine); detection limits are (1.2 ± 0.1) × 10⁻⁶, (1.3 ± 0.1) × 10⁻⁷ and (5.3 ± 0.1) × 10⁻⁸ M, respectively. Using an additive of Co (III) tetrakis-(tert-butyl)-phthalocyanine leads to the increase of signal and lowering detection limit. Some practical advises concerning both the sensor design and selectivity of catecholamine determination are provided.     

Application of 2-mercaptobenzothiazole self-assembled monolayer on polycrystalline gold electrode as a nanosensor for determination of Ag(I)

Fabrication and application of a voltammetric sensor based on gold 2-mercaptobenzothiazole self-assembled monolayer (Au-MBT SAM) for determination of silver ion is described. Preliminary experiments were performed to characterize the monolayer. The surface pK_a determined for the MBT monolayer is 7.0. This value was obtained by impedimetric titration of the monolayer in the presence of Fe(CN)₆^3−/4− as a redox probe. The extent of surface coverage was evaluated as 1.52 × 10⁻⁹ mol cm⁻² based on charged consumed for reductive desorption of the monolayer in the 0.50 M NaOH solution. Then the sensor was used for determination of Ag(I) by square wave voltammetry. The parameters affecting the sensor response, such as pH and supporting electrolyte, were optimized. A dynamic calibration curve with two linear parts was obtained in the concentration ranges of 5 × 10⁻⁸-8 × 10⁻⁷ and 1 × 10⁻⁶-1 × 10⁻⁵ M of Ag(I). The detection limit adopted from cathodic striping square wave voltammetry was as 1 × 10⁻⁸ M for n = 7. Furthermore, the effect of potential interfering ions on the determination of Ag(I) was studied, and an appropriate method was used for the elimination of this effect.     

A flow-injection chemiluminescence method for the determination of some estrogens by enhancement of luminol-hydrogen peroxide-tetrasulfonated manganese phthalocyanine reaction

A novel flow-injection chemiluminescence (FI-CL) method for the determination of estrogens is proposed, based upon its enhancing effect on the CL reaction of luminol with hydrogen peroxide catalyzed by tetrasulfonated manganese phthalocyanine (MnTSPc) in alkaline solution. Under the selected experimental conditions, a linear relationship was obtained between the CL intensity and the concentration of estrone in the range of 1.0 × 10⁻⁷ to 1.0 × 10⁻⁶ mol/l, estradiol in the range of 9.0 × 10⁻⁸ to 1.0 × 10⁻⁶ mol/l and estriol in the range of 3.0 × 10⁻⁷ to 2.0 × 10⁻⁶ mol/l, respectively. The detection limits were 5.1 × 10⁻⁸ mol/l for estrone, 7.2 × 10⁻⁹ mol/l for estradiol and 6.5 × 10⁻⁸ mol/l for estriol with a relative standard deviation of 2.8% for 5.0 × 10⁻⁷ mol/l estrone, 2.4% for 1.0 × 10⁻⁷ mol/l estradiol, and 3.1% for 7.0 × 10⁻⁷ mol/l estriol (n = 11). This method has been applied to the determination of estrogen in pharmaceutical injections and tap water with satisfactory results.     

11-Molybdobismuthophosphate—A new reagent for the determination of ascorbic acid in batch and sequential injection systems

The guanidinium salt of the new heteropolymolybdate 11-molybdobismuthophosphate Gua₆PBiMo₁₁O₄₀ (11-MBP) was synthesized, characterized and used as a reagent for batch spectrophotometric (SP) and sequential injection determination of ascorbic acid (AsA). When compared to other Keggin's heteropolyanions, the reduction of 11-MBP with AsA is both fast and maximal within a pH range of 1.6-2.0. The stoichiometry of the reaction was determined using molar ratio and continuous variation methods and was shown to be 1:1. The molar absorptivity of the reduced form of 11-MBP was 6.0 × 10³ L mol⁻¹ cm⁻¹ at 720 nm. The reaction is also specific for AsA. Only cysteine, hydroquinone and hydroxyacids were found to interfere with the reaction, while no interference was observed with the common reducing agents, including reducing sugars, catecholamines, nitrite, sulfite and iron(II) ions. Batch SP and sequential injection analysis (SIA) systems were developed for the determination of AsA, with calibration ranges of the SP methods at 2 × 10⁻⁶-8 × 10⁻⁵ M for a 10 mm cell and 5 × 10⁻⁷-3 × 10⁻⁵ M for a 50 mm cell and a limit of detection at 3 × 10⁻⁷ M. The linear range of the SIA method was 6 × 10⁻⁶-5 × 10⁻⁴ M, with a detection limit of 2 × 10⁻⁶ M and a sample throughput of 15 h⁻¹. The proposed methods were successfully used for the determination of AsA in both pharmaceuticals and fruit juices, and the results were consistent with those provided by the 2,6-dichlorophenolindophenol method.     

Quantification of biogenic amines by microchip electrophoresis with chemiluminescence detection

A highly sensitive microchip electrophoresis (MCE) method with chemiluminescence (CL) detection was developed for the determination of biogenic amines including agmatine (Agm), epinephrine (E), dopamine (DA), tyramine, and histamine in human urine samples. To achieve a high assay sensitivity, the targeted analytes were pre-column labeled by a CL tagging reagent, N-(4-aminobutyl)-N-ethylisoluminol (ABEI). ABEI-tagged biogenic amines after MCE separation reacted with hydrogen peroxide in the presence of horseradish peroxidase (HRP), producing CL emission. Since no CL reagent was added to the running buffer, the background of the CL detection was extremely low, resulting in a significant improvement in detection sensitivity. Detection limits (S/N = 3) were in the range from 5.9 × 10⁻⁸ to 7.7 × 10⁻⁸ M for the biogenic amines tested, which were at least 10 times lower than those of the MCE–CL methods previously reported. Separation of a urine sample on a 7 cm glass/poly(dimethylsiloxane) (PDMS) microchip channel was completed within 3 min. Analysis of human urine samples found that the levels of Agm, E and DA were in the ranges of 2.61 × 10⁻⁷ to 4.30 × 10⁻⁷ M, 0.81 × 10⁻⁷ to 1.12 × 10⁻⁷ M, and 8.76 × 10⁻⁷ to 11.21 × 10⁻⁷ M (n = 4), respectively.     

Direct determination of trace aluminum with quercetin by reversed-phase high performance liquid chromatography

The determination of trace levels of aluminum by high performance liquid chromatography (HPLC) with spectrophotometric detection using quercetin, a bioactive substance as a pre-column reagent, is developed in this paper. The Al-quercetin chelate was separated on a reversed-phase ODS column with a mobile phase consisting of 70% water (pH 1.0 with perchloric acid) and 30% methanol, and detected at its maximum of 415 nm. The response was linear over the 1.0×10⁻⁷ to 8.0×10⁻⁵ M concentration range with a detection limit of 5.0×10⁻⁸ M and a relative standard deviation of 1.0% at the 5×10⁻⁶ M level. The analysis was free from common ions except iron, which could be successfully screened by 1,10-phenanthroline. This method has been employed to the determination of Al in environmental and biological samples. Moreover, direct speciation of labile monomeric Al, the toxic form of Al, in natural water by the present technique was explored. The coordination ratio of Al complex with quercetin was also elucidated by HPLC combined with molar ratio method. Only a 1:1 complex was formed. Because quercetin exists in body, a preliminary thinking of in vivo determination of Al is provided in this study.     

Urea as new stabilizing agent for imipenem determination: electrochemical study and determination of imipenem and its primary metabolite in human urine

Imipenem shows a fast chemical conversion to a more stable imin form (identical to that of biochemical dehydropeptidase degradation) in aqueous solutions and stabilizing agents used avoid its electrochemical study and determination.The aim of this work is the proposal of urea as stabilizing agent which allows the electrochemical study of imipenem and the proposal of electrochemical methods for the determination of imipenem and its primary metabolite (M1) in human urine samples. Electrochemical studies were realized in phosphate buffer solutions over pH range 1.5-8.0 using differential-pulse polarography, DC-tast polarography, cyclic voltammetry and adsorptive stripping voltammetry. In acidic media, a non-reversible diffusion-controlled reduction involving a two steps mechanism which involves one electron and one proton in the first step and two electrons and two protons in the second step occurs and the mechanism for the reduction was suggested.A differential-pulse polarographic method for the determination of imipenem in the concentration range 3.2 × 10⁻⁶ to 2 × 10⁻⁵ M (0.95-3.4 mg/L) and its primary metabolite in the concentration range 1.4 × 10⁻⁶ to 10⁻⁴ M (0.43-26.1 mg/L) with detection limits of 9.6 × 10⁻⁷ M (0.28 μg/L imipenem) and 4.3 × 10⁻⁷ M (0.14 μg/L M1) was proposed. Also, a method based on controlled adsorptive pre-concentration of imipenem on the hanging mercury drop electrode followed by voltammetric measure, allows imipenem determination in the concentration range 1.8 × 10⁻⁸ to 1.2 × 10⁻⁶ M (5.42-347 μg/L) with a detection limit of 5.4 × 10⁻⁹ M (1.63 μg/L). The proposed methods have been used for the direct determination of the analytes in a pharmaceutical formulation and human urine.     

An electrochemical sensor prepared by sonochemical one-pot synthesis of multi-walled carbon nanotube-supported cobalt nanoparticles for the simultaneous determination of paracetamol and dopamine

Multi-walled carbon nanotubes (MWCNTs) functionalized by cobalt nanoparticles were obtained using a single step chemical deposition method in an ultrasonic bath. The composite material was characterized using scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDX). The electroactivity of the cobalt-functionalized MWCNTs was assessed in respect to the electrooxidation of paracetamol (PAR) and dopamine (DA). It was found that the carbon nanotube supported cobalt nanoparticles have significantly higher catalytic properties. The proposed electrode has been applied for the simultaneous determination of PAR and DA. The modified electrode could resolve the overlapped voltammetric waves of PAR and DA into two well-defined voltammetric peaks with peak to peak separation of about 203 mV. On the other hand, the presence of potential drug interfering compounds AA and UA did not affect the voltammetric responses of PAR and DA. The current of oxidation peaks showed a linear dependent on the concentrations of PAR and DA in the range of 5.2 × 10⁻⁹–4.5 × 10⁻⁷ M (R² = 0.9987) and 5.0 × 10⁻⁸–3.0 × 10⁻⁶ M (R² = 0.9999), respectively. The detection limits of 1.0 × 10⁻⁹ M and 1.5 × 10⁻⁸ M were obtained for PAR and DA, respectively. The proposed electrode showed good stability (peak current change: 4.9% with and RSD of 2.6% for PAR; 5.5% with and RSD of 3.0% for DA over 3 weeks), reproducibility (RSD 2.3% for PAR and RSD 1.5% for DA), repeatability (RSD 2.25% for PAR and RSD 2.50% for DA) and high recovery (99.7% with an RSD of 1.3% for PAR; 100.8% with an RSD of 1.8% for DA). The proposed method was successfully applied to the determination of PAR and DA in pharmaceuticals.     

Selective response of dopamine in the presence of ascorbic acid on carbon paste electrode modified with titanium phosphated silica gel

Titanium phosphate grafted on the surface of silica gel (devoted briefly as Si-TiPH) was synthesized and used as bulk modifier to fabricate a renewable three-dimensional chemically modified electrode. The Si-TiPH bulk modified carbon paste electrode was used for the selective determination of dopamine (DA) in the presence of ascorbic acid (AA). The modified electrode offers an excellent and stable response for the determination of DA in the presence of AA. The differential pulse voltammetry peak current was found to be linear with the DA concentration in the range 2 × 10⁻⁷ to 1 × 10⁻⁶ and 2 × 10⁻⁶ to 6 × 10⁻⁵ mol L⁻¹. The detection limit of the proposed method in the presence of 2.0 × 10⁻⁵ M of AA was found to be 4.3 × 10⁻⁸ mol L⁻¹ for DA determination. The proposed method was successfully applied for the determination of DA in injections.