Flow injection fluorescence determination of dopamine using a photo induced electron transfer (PET) boronic acid derivative

An automated flow injection analysis system was developed for the fluorometric determination of dopamine in pharmaceutical injections. The method is based on the quenching effect of dopamine on m-dansylaminophenyl boronic acid (DAPB) fluorescence due to the reverse photo induced electron transfer (PET) mechanism. Effects of pH and interfering species on the determination of dopamine were examined. Calibration for dopamine, based on quenching data, was linear in the concentration range of 1.0 × 10⁻⁵ to 1.0 × 10⁻⁴ M. Detection limit (3 s) of the method was found to be 3.7 × 10⁻⁶ M. Relative standard deviation of 1.2% (n = 10) was obtained with 1.0 × 10⁻⁵ M dopamine standard solution. The proposed method was applied successfully for the determination of dopamine in pharmaceutical injection sample. The sampling rate was determined as 24 samples per hour.     

Development of integrated chemiluminescence flow sensor for the determination of adrenaline and isoprenaline

A novel integrated chemiluminescence (CL) flow sensor for the determination of adrenaline and isoprenaline is developed based on the enhancing effect of analytes on CL emission of luminol oxidized by periodate in alkaline solution. The analytical reagents luminol and periodate are immobilized on anion exchange resins, respectively, and packed in a glass tube to construct a reagentless sensor. The proposed sensor allows the determination of adrenaline and isoprenaline over the range from 2.0×10⁻⁸ to 1.0×10⁻⁵ g ml⁻¹ and 2.0×10⁻⁷ to 5.0×10⁻⁵ g ml⁻¹, respectively. The detection limits are 7.0×10⁻⁹ g ml⁻¹ for adrenaline and 5.0×10⁻⁸ g ml⁻¹ for isoprenaline with a relative standard deviation of 1.7% for the 1.0×10⁻⁷ g ml⁻¹ adrenaline (n=11) and 2.1% for 1.0×10⁻⁶ g ml⁻¹ isoprenaline (n=11). The sample throughput was 60 samples h⁻¹. The sensor has been successfully applied to the determination of adrenaline and isoprenaline in pharmaceutical preparations.     

Trace determination of thiosulphate and thioglycolic acid using novel inhibitory kinetic spectrophotometric method

Sulphur containing compounds such as sodium thiosulphate (STS) and thioglycolic acid (TGA) inhibit the rate of cyanide substitution by nitroso-R-salt (NRS) in hexacyanoruthenate(II) catalysed by Hg(II) ions due to their strong binding tendencies with Hg(II) catalyst. This inhibitory effect of sodium thiosulphate and thioglycolic acid is used as the basis for their determination at micro levels. The reaction was followed spectrophotometrically at 525 nm (λ_max of [Ru(CN)₅NRS]³⁻ complex) under optimised reaction conditions at 8.75 × 10^− 5 M [Ru(CN)₆⁴⁻], 3.50 × 10^− 4 M [NRS], pH 7.00 ± 0.02, ionic strength (µ) 0.1 M (KCl) and temp 45.0 ±0.1 °C. The modified mechanistic scheme is proposed to understand the inhibition caused by sulphur containing compounds (STS and TGA) on Hg(II) catalysed substitution of cyanide by NRS in [Ru(CN)₆]⁴⁻. The range of analytical concentration of inhibitor depends upon two factors; the amount of Hg(II) catalyst present in the indicator reaction and the stability of the Hg(II)-inhibitor complex under consideration. Under optimum conditions STS and TGA have been determined in the range of 0.98-7.0 × 10^− 6 M and 0.30-7.0 × 10^− 6 M. The detection limits for STS and TGA were found to be 3.0 × 10^− 7 M and 1.0 × 10^− 7 M respectively.     

Gold nanoparticles modified indium tin oxide electrode for the simultaneous determination of dopamine and serotonin: Application in pharmaceutical formulations and biological fluids

A new rapid, convenient and sensitive electrochemical method based on a gold nanoparticles modified ITO (Au/ITO) electrode is described for the detection of dopamine and serotonin in the presence of a high concentration of ascorbic acid. The electrocatalytic response was evaluated by differential pulse voltammetry (DPV) and the modified electrode exhibited good electrocatalytic properties towards dopamine and serotonin oxidation with a peak potential of 70 mV and 240 mV lower than that at the bare ITO electrode, respectively. The selective sensing of dopamine is further improved by applying square wave voltammetry (SWV) which leads to the lowering of its detection limit. A similar effect on the detection limit of serotonin was observed on using SWV. Linear calibration curves are obtained in the range 1.0 × 10⁻⁹-5.0 × 10⁻⁴ M and 1.0 × 10⁻⁸-2.5 × 10⁻⁴ M with a detection limit of 0.5 nM and 3.0 nM for dopamine and serotonin, respectively. The Au/ITO electrode efficiently determines both the biomolecules simultaneously, even in the presence of a large excess of ascorbic acid. The adequacy of the developed method was evaluated by applying it to the determination of the content of dopamine in dopamine hydrochloride injections. The proposed procedure was also successfully applied to simultaneously detect dopamine and serotonin in human serum and urine.     

Highly selective and sensitive thiocyanate membrane electrode based on nickel(II)-1,4,8,11,15,18,22,25-octabutoxyphthalocyanine

A highly selective membrane electrode based on nickel(II)-1,4,8,11,15,18,22,25-octabutoxyphthalocyanine (NOBP) is presented. The proposed electrode shows very good selectivity for thiocyanate ions over a wide variety of common inorganic and organic anions. The sensor displays a near Nernstian slope of −58.7 ± 0.6 mV per decade. The working concentration range of the electrode is 1.0 × 10⁻⁶ to −1.0 × 10⁻¹ M with a detection limit of 5.7 × 10⁻⁷ M (33.06 ng/mL). The response time of the sensor in whole concentration ranges is very short (<10 s). The response of the sensor is independent on the pH range of 4.3-9.8. The best performance was obtained with a membrane composition of 30% PVC, 65% dibutyl phthalate, 3% NOBP and 2% hexadecyltrimethylammonium bromide. It was successfully applied to direct determination of thiocyanate in biological samples, and as an indicator electrode for titration of thiocyanate ions with AgNO₃ solution.     

Carbon paste electrode modified with silver thimerosal for the potentiometric flow injection analysis of silver(I)

The utility of carbon paste electrode modified with silver ethylmercurythiosalicylate (silver thimerosal) in both static mode and flow injection analysis (FIA) is demonstrated. The electrode was fully characterized in terms of composition, response time, thermal stability, usable pH and ionic strength ranges. It has been shown that diisononyl phthalate (DINP) acts as more suitable solvent mediator for preparation of the electrode, which exhibits linear response range to Ag(I) extending from 5.0 × 10⁻⁷ to 1.0 × 10⁻³ M with detection limit of 2.5 × 10⁻⁷ M and Nernstian slope of 59.3 ± 1.0 mV/decade. The proposed chemically modified carbon paste electrode shows a very good selectivity for Ag(I) over a wide variety of metal ions and successfully used for the determination of the silver content of silver sulphadiazine (burning cream) and developed radiological films. The electrode was also used as an indicator electrode in the potentiometric titration of thiopental and thimerosal with AgNO₃.     

Integrated multienzyme electrochemical biosensors for the determination of glycerol in wines

The construction and performance of integrated amperometric biosensors for the determination of glycerol are reported. Two different biosensor configurations have been evaluated: one based on the glycerol dehydrogenase/diaphorase (GDH/DP) bienzyme system, and another using glycerol kinase/glycerol-3-phosphate oxidase/peroxidase (GK/GPOx/HRP). Both enzyme systems were immobilized together with the mediator tetrathiafulvalene (TTF) on a 3-mercaptopropionic acid (MPA) self-assembled monolayer (SAM)-modified gold electrode by using a dialysis membrane. The electrochemical oxidation of TTF at +150 mV (vs. Ag/AgCl), and the reduction of TTF⁺ at 0 mV were used for the monitoring of the enzyme reactions for the bienzyme and trienzyme configurations, respectively. Experimental variables concerning both the biosensors composition and the working conditions were optimized for each configuration. A good repeatability of the measurements with no need of cleaning or pretreatment of the biosensors was obtained in both cases. After 51 days of use, the GDH/DP biosensor still exhibited 87% of the original sensitivity, while the GK/GPOx/HRP biosensor yielded a 46% of the original response after 8 days. Calibration graphs for glycerol with linear ranges of 1.0 × 10⁻⁶ to 2.0 × 10⁻⁵ or 1.0 × 10⁻⁶ to 1.0 × 10⁻⁵ M glycerol and sensitivities of 1214 ± 21 or 1460 ± 34 μA M⁻¹ were obtained with GDH/DP and GK/GPOx/HRP biosensors, respectively. The calculated detection limits were 4.0 × 10⁻⁷ and 3.1 × 10⁻⁷ M, respectively. The biosensors exhibited a great sensitivity with no significant interferences in the analysis of wines. The biosensors were applied to the determination of glycerol in 12 different wines and the results advantageously compared with those provided by a commercial enzyme kit.     

New potentiometric sensors for creatinine

Three main types of creatinine potentiometric membrane sensors are described. They are based on the use of dibenzo-30-crown-10 (DB30C10) with potassium tetrakis(p-chlorophenyl)borate type (I), dibenzo-30-crown-10 alone type (II), and potassium tetrakis(p-chlorophenyl)borate alone type (III), incorporating in poly(vinyl chloride) matrix membrane plasticized with either o-nitrophenyl octyl ether or dioctylphthalate. The sensors are used for quantification of creatinine after soaking the membranes in 0.1 M creatinine solution for 2 days. The sensors show almost the same potentiometric response characteristics. Sensor type (I) exhibits Nernstian responses over a concentration range of 5.0 × 10⁻⁵ mol l⁻¹-1.0 × 10⁻² mol l⁻¹ creatinine with cationic slopes of 59.5 ± 0.1 and 60 ± 0.2 mV decade⁻¹ and detection limits of 1.1 × 10⁻⁵ mol l⁻¹ and 8 × 10⁻⁶ mol l⁻¹ creatinine, over the pH range of 3.5-6.5 and 3.5-7.0, for o-NPOE and DOP solvent mediators, respectively. Sensor type (II) displays Nernstian responses over a concentration range of 6.0 × 10⁻⁵ mol l⁻¹-1.0 × 10⁻² mol l⁻¹ creatinine with cationic slopes of 60.0 ± 0.1 and 65.0 ± 0.2 mV decade⁻¹ and detection limits of 1.5 × 10⁻⁵ mol l⁻¹ and 1.4 × 10⁻⁵ mol l⁻¹ creatinine over the pH range of 2.6-6.2 and 2.5-6.0, for o-NPOE and DOP solvent mediators, respectively. Sensor type (III) shows Nernstian responses over a concentration range of 7.0 × 10⁻⁵ mol l⁻¹-1.0 × 10⁻² mol l⁻¹ creatinine with cationic slopes of 60 ± 0.1 and 62.0 ± 0.2 mV decade⁻¹ and detection limits of 2.7 × 10⁻⁵ mol l⁻¹ and 2.0 × 10⁻⁵ mol l⁻¹ creatinine over the pH range of 2.5-6.0, for o-NPOE and DOP solvent mediators, respectively. The response times of the sensors for 10⁻³ mol l⁻¹ creatinine solution are instantaneous (4-10 s). The sensors show long-term stability with life span of ∼6 months. The sensors are used for determination of serum creatinine of rats (Rattus Norvigicus) with mean R.S.D. of 2.62%, and the results agreed well with the Jaffe kinetic method.     

A selective modified carbon paste electrode for determination of cyanide using tetra-3,4-pyridinoporphyrazinatocobalt(II)

A chemically modified carbon paste electrode with 3,4-tetra pyridinoporphirazinatocobalt(II) (Co(3,4 tppa) was applied to the determination of free cyanide ion. The electrode has a linear range between 1.5 × 10⁻⁵ M and 1.0 × 10⁻² M with a Nernstian slope of 60 ± 1.5 mV/decade and its detection limit is 9 × 10⁻⁶ M. The response time of electrode is 5 min. The proposed electrode was applied successfully for the determination of cyanide in commercially available spring water. Some anions, such as SCN⁻, I⁻, Cl⁻, Br⁻ and oxalate that are usually serious interfering species for most of cyanide selective electrodes, did not have any interfering effect for this proposed electrode.     

Determination of adrenaline by using inhibited Ru(bpy)3 electrochemiluminescence

Adrenaline was found to inhibit strongly the electrochemiluminescence (ECL) from the Ru(bpy)₃²⁺/tripropylamine system when a working Pt electrode was maintained at 1.05 V (versus Ag/AgCl) in pH 8.0 phosphate buffer. On this basis, a flow injection (FI) procedure with inhibited electrochemiluminescence detection has been developed for determination of adrenaline. The method exhibited a good reproducibility, sensitivity, and stability with a detection limit (signal-to-noise ratio = 3) of 7.0×10⁻⁹ mol l⁻¹ and dynamic concentration range of 2×10⁻⁸ to 1×10⁻⁴ mol l⁻¹. The relative standard deviation was 2.2% for 1.0×10⁻⁶ mol l⁻¹ adrenaline (n=11). The method was successfully applied to the determination of adrenaline in pharmaceutical samples. Moreover, ECL emission spectra, UV-Vis absorption spectra and cyclic voltammograms of Ru(bpy)₃²⁺/tripropylamine/adrenaline were studied. The inhibition mechanism has been proposed as the interaction of electrogenerated Ru(bpy)₃^2+* and the o-benzoquinone derivatives, adrenochrome and adrenalinequinone, at the electrode surface.     

Determination of l-histidine by modified carbon paste electrode using tetra-3,4-pyridinoporphirazinatocopper(II)

This paper describes a potentiometric method for determination of l-histidine (l-his) in aqueous media, using a carbon paste electrode modified with tetra-3,4-pyridinoporphirazinatocopper(II) (Cu (3,4tppa)). The electrode exhibits linear response to the logarithm of the concentration of l-histidine from 2.4 × 10⁻⁵ to 1.0 × 10⁻² M, with a response slope of −49.5 ± 1 mV and response time of about 1.5 min. The detection limit according to IUPAC recommendation was 2.0 × 10⁻⁵ M. The proposed electrode shows a good selectivity for l-his over a wide variety of anions. This chemically modified carbon paste electrode was successfully used for the determination of l-his in a synthetic serum and RANDOX control serum solutions.     

Molecularly imprinted polymer based potentiometric sensor for the determination of hydroxyzine in tablets and biological fluids

Molecular imprinting is a useful technique for the preparation of functional materials with molecular recognition properties. In this work, a biomimetic potentiometric sensor, based on a non-covalent imprinted polymer, was fabricated for the recognition and determination of hydroxyzine in tablets and biological fluids. The molecularly imprinted polymer (MIP) was synthesized by precipitation polymerization, using hydroxyzine dihydrochloride as a template molecule, methacrylic acid (MAA) as a functional monomer and ethylene glycol dimethacrylat (EGDMA) as a cross-linking agent. The sensor showed a high selectivity and a sensitive response to the template in aqueous system. The MIP-modified electrode exhibited a Nernstian response (29.4 ± 1.0 mV decade⁻¹) in a wide concentration range of 1.0 × 10⁻⁶ to 1.0 × 10⁻¹ M with a lower detection limit of 7.0 × 10⁻⁷ M. The electrode demonstrated a response time of ∼15 s, a high performance and a satisfactory long-term stability (more than 5 months). The method has the requisite accuracy, sensitivity and precision to assay hydroxyzine in tablets and biological fluids.     

Highly selective thiocyanate membrane electrode based on butane-2,3-dione bis(salicylhydrazonato)zinc(II) complex

A highly selective poly(vinyl chloride) (PVC) membrane electrode based on butane -2,3-dione bis(salicylhydrazonato) zinc(II) [Zn (BDSH)] complex as carrier for thiocyanate-selective electrode is reported. The influence of membrane composition, pH and possible interfering anions were investigated on the response properties of the electrode. The sensor responds to thiocyanate in linear range from 1.0 × 10⁻⁶ to 1.0 × 10⁻¹ M with a slope −56.5 ± 1.1 mV decade⁻¹, over a wide pH range of 3.5-8.5. The limit of detection of the electrode was 7.0 × 10⁻⁷ M SCN⁻. Selectivity coefficients determined with fixed interference method (FIM) indicate a good discriminating ability towards SCN⁻ ion in comparison to other anions. The proposed sensor has a fast response time of about 5-15 s and can be used for at least 3 months without any considerable divergence in potential. It was applied as indicator electrode in titration of thiocyanate with Ag⁺ and in potentiometric determination of thiocyanate in saliva and urine samples.     

Zeolite A functionalized with copper nanoparticles and graphene oxide for simultaneous electrochemical determination of dopamine and ascorbic acid

A novel Cu-zeolite A/graphene modified glassy carbon electrode for the simultaneous electrochemical determination of dopamine (DA) and ascorbic acid (AA) has been described. The Cu-zeolite A/graphene composites were prepared using Cu²⁺ functionalized zeolite A and graphene oxide as the precursor, and subsequently reduced by chemical agents. The composites were characterized by X-ray diffraction, Fourier transform infrared spectra and scanning electron microscopy. Based on the Cu-zeolite A/graphene-modified electrode, the potential difference between the oxidation peaks of DA and AA was over 200 mV, which was adequate for the simultaneous electrochemical determination of DA and AA. Also the proposed Cu-zeolite/graphene-modified electrode showed higher electrocatalytic performance than zeolite/graphene electrode or graphene-modified electrode. The electrocatalytic oxidation currents of DA and AA were linearly related to the corresponding concentration in the range of 1.0 × 10⁻⁷–1.9 × 10⁻⁵ M for DA and 2.0 × 10⁻⁵–2.0 × 10⁻⁴ M for AA. Detection limits (<!-- no-mfc -->S/N<!-- /no-mfc --> = 3) were estimated to be 4.1 × 10⁻⁸ M for DA and 1.1 × 10⁻⁵ M for AA, respectively.     

Dodecyl benzene sulfonate anion-selective electrode based on polyaniline-coated electrode

A new dodecyl benzene sulfonate (DBS⁻) ion-selective electrode based on polyaniline is reported. The films of polyaniline doped with DBS⁻ were prepared electrochemically on platinum electrodes in the solution containing 1.0×10⁻³ M aniline and 7.0×10⁻³ M DBS⁻. The optimum potentiometric response was obtained for prepared polymeric film by passing electricity of 7.5 C cm⁻². The electrode exhibits an excellent Nernstian slope of −59.1±0.3 mV per decade for DBS⁻ ion over a wide concentration range (5.0×10⁻⁶ to 4.1×10⁻³ M) with a low detection limit (1.0×10⁻⁶ M). The proposed electrode revealed good sensitivities for DBS⁻ ion over a wide variety of other anions and can be used in the wide pH range of 5-10. It shows good stability, good reproducibility, wide range of pH independency and fast response (<20 s) without using internal solution. This electrode could be used for the determination of DBS⁻ in the real samples.     

Micro determination of ascorbic acid using methyl viologen

A new simple and sensitive analytical spectrophotometric method is developed for the determination of ascorbic acid reduces methyl viologen to form a stable blue coloured free radical ion. This method has a sensitivity and lower limit detection of 0.1 μg ml⁻¹ of ascorbic acid (0.1 ppm) which is comparable to the flow injection analysis reported earlier. Beer's law is obeyed over the concentration range of 1.0-10 μg ml⁻¹ of ascorbic acid per 10 ml of the final solution (0.1-1.0 μg ml⁻¹) at 600 nm. The molar absorptivity and Sandell's sensitivity were found to be 1.5 × 10⁵ ± 100 l mol⁻¹ cm⁻¹ and 0.001 μg cm⁻², respectively. The method has been applied to the determination of ascorbic acid in food, pharmaceuticals and biological samples.     

Anodic voltammetric behavior of resveratrol and its electroanalytical determination in pharmaceutical dosage form and urine

The anodic voltammetric behavior of resveratrol was studied using cyclic and square wave voltammetric techniques. The oxidation of resveratrol is irreversible and exhibits an adsorption controlled process which is of pH dependence. The oxidation mechanism was proposed in this work. The dependence of the current on pH, the concentration and nature of buffer, and scan rate was investigated to optimize the experimental conditions for the determination of resveratrol. It was found that the optimum buffer for the determination of resveratrol is 1.0 × 10⁻³ M KCl + 0.1 M HNO₃ solution with the pH of 1.0. In the range of 5.00 × 10⁻⁹ to 1.65 × 10⁻⁷ M, the current measured by square wave voltammetry presents a good linear property as a function of the concentration of resveratrol. In addition, the reproducibility, precision and accuracy of the method were checked as well. The method was applied for the determination of resveratrol in Chinese patent medicine and diluted urine.     

Membrane electrodes for the determination of glutathione

Four glutathione (GSH)-selective electrodes were developed with different techniques and in different polymeric matrices. Precipitation-based technique with bathophenanthroline-ferrous as cationic exchanger in polyvinyl chloride (PVC) matrix was used for sensor 1 fabrication. β-Cyclodextrin (β-CD)-based technique with either tetrakis(4-chlorophenyl)borate (TpClPB) or bathophenanthroline-ferrous as fixed anionic and cationic sites in PVC matrix was used for fabrication of sensors 2 and 3, respectively.β-CD-based technique with TpClPB as fixed anionic site in polyurethane (Tecoflex) matrix was used for sensor 4 fabrication. Linear responses of 1 × 10⁻⁵ to 1 × 10⁻⁴ M and 1 × 10⁻⁶ to 1 × 10⁻³ M with slopes of 37.5 and 32.0 mV/decade within pH 7-8 were obtained by using electrodes 1 and 3, respectively. On the other hand, linear responses of 1 × 10⁻⁵ to 1 × 10⁻² and 1 × 10⁻⁵ to 1 × 10⁻³ M with slopes of 47.9 and 54.3 mV/decade within pH 5-6 were obtained by using electrodes 2 and 4, respectively. The percentage recoveries for determination of GSH by the four proposed GSH-selective electrodes were 100 ± 1, 100.5 ± 0.7, 100 ± 1 and 99.0 ± 0.8% for sensors 1, 2, 3 and 4, respectively. Determination of GSH in capsules by the proposed electrodes revealed their applicability for determination of GSH in its pharmaceutical formulations. Also, they were used to determine GSH selectively in presence of its oxidized form (GSSG). Sensor 4 was successfully applied for determination of glutathione in plasma with average recovery of 100.4 ± 1.11%. The proposed method was compared with a reported one. No significant difference for both accuracy and precision was observed.     

Kinetic determination of cysteine and thiosulphate by inhibition of Hg(II) catalyzed ligand substitution reaction

The sulphur containing inhibitors (I), cysteine (Cys) and sodium thiosulphate (THS), have been found to inhibit Hg(II) catalyzed exchange of cyanide in hexacyanoferrate(II) by nitroso-R-salt (NRS). The inhibitory effect of both the ligands are attributed to their binding tendencies with Hg(II) leading to the formation of catalyst-inhibitor (C-I) complex. The reactions have been followed spectrophotometrically in aqueous medium at 720 nm by noting the increase in absorbance of the green colour product, [Fe(CN)₅NRS]³⁻ at pH 6.50 ± 0.02, temp 25.0 ± 0.1 °C and ionic strength (μ) 0.1 M (KNO₃). A most plausible mechanistic scheme involving the role of analytes (inhibitors) has been proposed. The values of equilibrium constants for complex formation between catalyst-inhibitor (K_CI), catalyst-substrate (K_S) and Mechaelis-Menton constant (K_m) have been computed from the kinetic data. The linear calibration curves have been established between absorbance and inhibitor concentrations under specified conditions. Cys and THS have been determined in the range 1-5 × 10^− 7 M and 4.9-16.9 × 10^− 7 M respectively. The detection limits have been computed to be 1 × 10^− 7 M and 4.9 × 10^− 7 M for Cys and THS, respectively.     

Time measurement-visual analysis of l-cysteine using the autocatalytic sodium sulfite/hydrogen peroxide reaction system and its application to length detection-flow analysis

Trace amounts of l-cysteine can function as a trigger, i.e., reaction initiator, in the autocatalytic sodium sulfite/hydrogen peroxide reaction system. Rapidly changing of pH after induction time is visually confirmed by color changing of bromothymol blue in this autocatalytic reaction. Based on this finding, μg L⁻¹ levels of l-cysteine were measured over time using the autocatalytic reaction system. The determination range using the above method was 5.0 × 10⁻⁸-2.5 × 10⁻⁶ M, the detection limit (3σ) was 1.8 × 10⁻⁸ M (1.94 μg L⁻¹), and the relative standard deviation was 2.41% at an l-cysteine concentration of 5 × 10⁻⁷ M (n = 5). This method was also applied to length detection-flow injection analysis. The determination range for the flow injection analysis was 2.0 × 10⁻⁷-1.0 × 10⁻⁵ M. The detection limit (3σ) was 1.4 × 10⁻⁷ M (17.0 μg L⁻¹), and the relative standard deviation was 0.91% at an initial l-cysteine concentration of 10⁻⁶ M (n = 5).