Sol-Gel Processed TiO2-Based Nano-Sized Powders for Use in Thick-Film Gas Sensors for Atmospheric Pollutant Monitoring

Sol-gel routes were used to prepare pure and 5 at% and 10 at% Ta- or Nb-dope TiO₂ nano-sized powders. The thermal decomposition behaviour of the precursors was studied using simultaneous thermogravimetric and differential thermal analysis (TG/DTA). X-ray diffraction (XRD) analysis showed that the powders heated to 400°C were crystalline in the anatase TiO₂ structure. The pure TiO₂ powder heated to 850°C showed the rutile structure. The addition of Ta and Nb inhibited the anatase-to-rutile phase transformation up to 950–1050°C. Ta was soluble in the titania lattice up to the concentration of 10 at%, while the solubility of Nb was 5 at%. Thick films were fabricated with these powders by screen printing technology and then fired for 1 h at different temperatures in the 650–1050°C range. Scanning electron microscopy (SEM) observations showed that the anatase-to-rutile phase transformation induces a grain growth of about one order of magnitude for pure TiO₂. The addition of Ta and Nb is effective to keep the TiO₂ grain size at a nanometric level even at 950°C, though grain growth was observed with increasing temperature. The gas-sensitive electrical response of the thick films were tested in laboratory, in environments with CO in dry and wet air. Conductance measurements showed a good gas response only for the nanostructured titania-based films. For field tests, the prototype sensors were placed beside a conventional station for atmospheric pollutant monitoring. The electrical response of the thick films was compared with the results of the analytical instruments. The same trend was observed for both systems, demonstrating the use of gas sensors for this aim.     

XAS investigation of tantalum and niobium in nanostructured TiO2 anatase

Sol-gel routes were used to prepare Ta 10 at% and Nb 5 at% and 10 at% doped titania nanosized powders. When fired between 410°C and 850°C the doped titania powders are in the anatase phase; further heating up to 1050°C is required to obtain the rutile phase. The presence of dopant atoms delays the rate of transformation as compared with pure titania powders. Doping also affects the rate of grain growth and increases the conductance response to gas. To better understand the role played by dopant atoms in inhibiting both phase transformation to rutile and grain growth, X-ray Absorption Spectroscopy measurements were performed at the L_III-L_I absorption edges of Ta and Nb K absorption edge. Analysis was restricted to the anatase phase because the transformation to rutile phase, obtained by firing at 1050°C, is accompanied by the formation of undesired Ta and Nb oxides (Ta₂O₅ and Nb₂TiO₇, respectively). Extended X-ray Absorption Fine Structure and X-ray Absorption Near-Edge Spectroscopy analysis results indicate that in nanostructured anatase both tantalum and niobium atoms substitute Ti cations with +5 valence state.     

The effects of trace elements on the crystal properties of TiO2

The effects of trace element doping of TiO₂ on the crystal growth and on the anatase-to-rutile phase transformation of TiO₂ were investigated. The co-precipitation process, from sulfate solution, of doped (Cr, Fe, V, Nb, Si, P) TiO₂ was also studied. The heating temperatures were 473, 673, 873, 993, 1133 K and a higher temperature needed to achieve a rutile content of 98–99%. Traces of reduced titanium were found in freshly calcined anatase by X-ray diffraction. Pure anatase structure was found in 85% of the samples heated below 1000 K. Anatase-to-rutile transformation was accelerated by the mmol% content of Nb, Cr, Si, and Fe in TiO₂. Interaction of co-precipitated or impregnated cations was found critical in the phase transformation process. Nb retarded the crystal growth during calcination. Sulfate ions minimized the specific surface area of TiO₂ heated at low temperatures. These results of doped TiO₂ serve to promote the development of new high-technology TiO₂ products for photocatalytic purposes.     

Intermediate steps in YBa2Cu3O7−x synthesis by sol-gel method: YBaCuO oxycarbonate

High T _c -superconducting powders of the Y-Ba-Cu-O system are prepared by a solution-polyacrylamide gel using citric acid as a complexing agent. This method provides an easy way to prepare reactive YBaCuO powders by sol-gel synthesis. However this synthesis involves intermediate phases formation which impedes the obtention of the pure phase at low temperature. An intermediate oxycarbonate phase forms between 800° and 850°C in flowing oxygen. From powder X-ray diffraction, thermal analysis and IR spectroscopy, it is concluded that the intermediate oxycarbonate has an average tetragonal structure—SG P4/mmm—similar to that of the parent oxide with a stoichiometry close to YBa₂Cu_2.95(CO₃)_0.35O_6.6. The carbonate group is located in the center of the basal CuO square. This compound has superconducting properties. A pure 123 phase is obtained when the xerogel precursor is annealed at 925°C in O₂ or at 800°C in Ar, then in O₂. The grain growth and microstructure development of YBaCuO have also been investigated and compared using two different powders, i.e. sol-gel route and commercial powder from Hoechst.     

Electrical Properties of Transparent Doped Oxide Films

In the present study n-type and p-type transparent conductive TiO₂ films were prepared by using sol-gel method. The n-type TiO₂ films were obtained by using Ti(OC₃H ₇ ⁱ )₄ solutions co-doped with Ru and Ta. The films were uniform and transparent in all the conditions, and their crystalline phases were anatase when HCl or HNO₃ was used as a catalyst. The resistivity decreased with increasing Ta content and increased with increasing Ru content. Most of the films showed resistivity minima at a heat-treatment temperature of 700°C. The lowest resistivity of 10¹ 10² cm was attained. The p-type TiO₂ films were obtained by using Ti(OC₃H ₇ ⁱ )₄ solutions co-doped with Co and Nb (Sb). The films were also uniform and transparent when AcAc was used, while samples heat-treated at 800°C became opaque when HCl was added. Rutile single phase appeared when the films were heat-treated at 700°C. Logarithmic resistivity of films co-doped with Co and Nb was directly proportional to the reciprocal absolute temperature. On the other hand, the slopes for films co-doped with Co and Sb were different below and above 200°–220°C. The activation energy at the low-temperature region is as low as 0.17 eV, and the resistivity at room temperature is 10⁴ 10⁵ cm.     

掺杂二氧化锡的二氧化钛的光学性质及其光催化特性

二氧化钛多相催化是一种极具前途的环境污染深度净化技术。 本文以钛酸四丁酯和四氯化锡为原料,无水乙醇为溶剂,采用溶胶-凝胶法制备了掺杂二氧化锡的二氧化钛薄膜和复合氧化物粉体。通过测量薄膜的吸收光谱推算光学能隙,结果发现掺杂样品的光学能隙比纯二氧化钛样品有所变小。随着热处理温度的提高,掺杂和纯二氧化钛样品的光学能隙都略微降低。X-射线衍射分析表明,复合氧化物粉体的热处理温度对样品的晶体结构和光催化性能有重要影响。以掺杂二氧化锡5 % 摩尔比的样品与纯二氧化钛对照,500 ℃以下热处理样品以锐钛矿结构为主,600 ℃热处理样品为锐钛矿与金红石相共存,并显示了较好的光催化性能。透射电子显微镜观察显示,同样600 ℃热处理,掺杂样品要比纯二氧化钛具有更小的颗粒尺寸。在700 ℃热处理的样品中,掺杂样品只存在金红石相而纯二氧化钛样品中仍存有锐钛矿相。用阿伦尼乌斯经验关系式推测的晶粒生长的活化能,纯二氧化钛47.486 kJ.mol, 掺杂5 % 摩尔比的复合氧化物样品33.103 kJ.mol。以亚甲基蓝为降解物质,考察了掺杂量和热处理温度对样品的光催化性能。     

SrBi2Nb2O9 Ferroelectric Powders and Thin Films Prepared by Sol-Gel

Pure SrBi2Nb2O9 powders and thin films were obtained using sol-gel synthesis from mixtures of niobium ethoxide, bismuth and strontium 2-ethylhexanoates. Powders crystallized for 2 hours at 700°C had grain sizes of about 100–150 nm. SrBi2Nb2O9 thin films were prepared by spin-coating a stable precursor solution onto Si/SiO2/TiO2/Pt substrates. Crystallization of pure SrBi2Nb2O9 phase occurred at about 500–550°C. Randomly oriented 0.3 m-thick crack-free films were obtained after 10 successive depositions and heating at 700°C for 2 hours. P-E hysteresis loops have confirmed the ferroelectric behavior of the films: they show a remanent polarization of 2.5 C/cm2 (5 V, 8 ms). No fatigue was observed up to 109 full switchings.     

Temperatures and kinetics of anatase to rutile transformation in doped TiO<Subscript>2</Subscript> heated in microwave field

The influence of aliovalent ions such as Mn, Cr, Fe, Mo, and V on the temperature and kinetics of anatase to rutile phase transformation in TiO₂ heated in microwave field was studied in this work. The results indicated that heat treatment method and dopants considerably affected the anatase-to-rutile phase transition temperature and kinetics of transformation. The activation energy for anatase to rutile transformation of TiO₂ derived from the isothermal data was found to be 328.4 kJ mol^–1, which was considerably reduced by the addition of dopants in TiO₂ matrix. The activation energy for Mo, Mn and V doped samples was 252.0, 101.3 and 96.4 kJ mol^–1, respectively.     

Photoactivity and phase stability of ZrO2-doped anatase-type TiO2 directly formed as nanometer-sized particles by hydrolysis under hydrothermal conditions

Anatase-type TiO₂ doped with 4.7 and 12.4 mol% ZrO₂ that were directly precipitated as nanometer-sized particles from acidic precursor solutions of TiOSO₄ and Zr(SO₄)₂ by simultaneous hydrolysis under hydrothermal conditions at 200°C, showed higher photocatalytic activity than pure anatase-type TiO₂ for the decomposition of methylene blue. The crystallite growth and the phase transformation from anatase-type to rutile-type structure caused by heating at high temperature were retarded by doping ZrO₂ into TiO₂. The anatase-type TiO₂ doped with ZrO₂ showed high phase stability and maintained anatase-type structure even after heating at 1000°C for 1 h.     

Phase composition and magnetic properties of niobium-iron codoped TiO2 nanoparticles synthesized in Ar/O2 radio-frequency thermal plasma

Nanoparticles of Nb⁵⁺-Fe³⁺ codoped TiO₂ with various Nb⁵⁺ concentrations (Nb/(Ti+Fe+Nb)=0-10.0 at%) and Fe³⁺ (Fe/(Ti+Fe+Nb)=0-2.0 at%) were synthesized using Ar/O₂ thermal plasma. Dopant content, chemical valence, phase identification, morphology and magnetic properties were determined using several characterization techniques, including inductively coupled plasma-optical emission spectrometer, X-ray photoelectron spectroscopy, X-ray diffraction, UV-vis diffuse reflectance spectrometer, field-emission scanning electron microscopy, transmission electron microscopy and SQUID commercial instrument. The XRD revealed that all the plasma-synthesized powders were exclusively composed of anatase as major phase and rutile. The rutile weight fraction was increased by the substitution of Fe³⁺ for Ti⁴⁺ whereas it was reduced by the Nb⁵⁺ doping. The plasma-synthesized Nb⁵⁺-Fe³⁺ codoped TiO₂ powders had intrinsic magnetic properties of strongly paramagnetic and feebly ferromagnetic at room temperature. The ferromagnetic properties gradually deteriorated as the Fe³⁺ concentration was decreased, suggesting that the ferromagnetism was predominated by the phase composition as a carrier-mediated exchange.     

Preparation and Characterization of Titania Thin Films from Aqueous Solutions

Dip- or spin-coating and characterization of titania (TiO₂) thin films from various aqueous solutions have been studied. The aqueous titanium solutions mainly used in this study were halogen- and chelate-free solutions with the concentrations up to 1.4 M derived from titanium isopropoxide (TIP) with tetramethylammonium hydroxide (TMAOH) or some alkylamines, while aqueous and alcoholic solutions containing titanium atoms stabilized chelating ligands were examined for comparison. The TiO₂ films prepared from the TIP-TMAOH solution were already crystallized at 350°C to anatase form and those formed at 600°C had high transparency and refractive indices of 2.40. No carbon residue in the film prepared at 400°C was detected by XPS. The pure anatase form was sustained up to 850°C. Interestingly, it was found that the (004) preferentially oriented anatase films were obtained from TIP-lactic acid (LA) system until 700°C. The solutions containing citric acid (CA) or alkanolamines yielded anatase and rutile form fired at the temperatures equal to or higher than 600°C. Carbon residue was detected in the film fired at 400°C. The film thickness monotonically decreased from the upper to the bottom ends of the substrate. However, it was found that the thickness uniformity was drastically improved by an addition of sucrose to the aqueous solutions. The effects of the solution composition and polyhydroxy compounds on the crystal modifications of formed films and the film uniformity are discussed.     

纳米掺铁二氧化钛的sol-gel法制备与表征 (Ⅱ)纳米掺铁二氧化钛的微晶特性与晶体生长

本文结合透射电镜分析研究了 sol-gel方法制备的纯二氧化钛和掺铁二氧化钛干凝胶的晶化过程。计算了在不同的煅烧温度下二氧化钛微晶的晶胞参数,晶粒度,畸变等参数的变化关系。应用非晶物质晶化晶核生长速率方程计算的晶粒生长活化能表明晶粒生长分为两个阶段,临界点大约为相变温度。纯的和掺铁的二氧化钛在两个阶段的晶粒生长活化能分别约为 20.8kJ· mol-1,70.9kJ· mol-1和 26.6kJ· mol-1,78.8kJ· mol-1。这个差别可能是由于相变过程首先发生在小晶粒上,导致小晶粒生长较为困难所致。     

纳米掺铁二氧化钛的sol-gel法制备与表征 (Ⅱ)纳米掺铁二氧化钛的微晶特性与晶体生长

本文结合透电镜分析研究了sol-gel方法制备的纯二氧化钛和掺铁二氧化钛干凝胶的晶化过程,计算了在不同的煅烧温度下二氧化钛微晶的晶胸参数,晶粒度,畸变等参数的变化关系,应用非晶物质晶化晶核生长速率议程计算的昌粒生长活化能表明晶粒生长分为两个阶段,临界点大约为相变温度,纯的和掺铁的二氧化钛在两个阶段的晶粒生长活化能分别约为20．8kJ.mol^-1,70.9kJ.mol^-1和26．6kJ.mol^-1,78.8kJ.mol^-1.这个差别可能是由于相主过程首先发生在小晶粒上,导致小晶粒生长较为困难所致。     

Effects of hydrothermal post-treatment on microstructures and morphology of titanate nanoribbons

Titanate nanoribbons were prepared via a hydrothermal treatment of rutile-type TiO₂ powders in a 10 M NaOH solution at 200 °C for 48 h. The as-prepared titanate nanoribbons were then hydrothermally post-treated at 150 °C for 12-36 h. The titanate nanoribbons before and after hydrothermal post-treatment were characterized with FESEM, XRD, TEM, UV-VIS and nitrogen adsorption-desorption isotherms. The results showed that the hydrothermal post-treatment not only promoted the phase transformation from titanate to anatase TiO₂, but also was beneficial to the removal of Na⁺ ions remained in the titanate nanoribbons. After hydrothermal post-treatment, the TiO₂ samples retained the one-dimensional structure feature of the titanate nanoribbons and showed an obvious increase in the specific surface area and the pore volume.     

Effects of synthesis parameters on the microstructure and phase structure of porous 316L stainless steel supported TiO2 membranes

Porous stainless steel (PSS) supported TiO₂ membrane was synthesized from colloidal TiO₂ sol by the sol–gel technique. Morphology and phase structure of the obtained membranes were regulated through optimizing the synthesis parameters including organic binders, aging periods of the parent sol and concentrations of the casting solutions as well as the sintering temperatures. Polyvinyl alcohol (PVA) 1750 was found to be feasible to fabricate TiO₂ membrane with relatively flat surface and homogeneous morphology without crack. The aging period of the parent sol, which was revealed to be very important to the morphology of the particles deposited in the membranes on PSS, was decided to be 24 h. The concentration, under which the membranes could avoid macro-pores and have a uniform thickness of approximately 8 μm, was regulated to 0.0036 mol/l. Besides, a homogeneous microstructure with grain sizes of 0.08–0.2 μm was obtained in the membrane with a pure rutile phase when sintered at 850 °C. The obtained PSS supported TiO₂ membrane with homogeneous microstructure and rutile phase may be very promising for practical applications.     

Synthesis of Spherical Titanium Dioxide Particles by Homogeneous Precipitation in Acetone Solution

Titania powders were synthesized by thermal hydrolysis of titanium tetrachloride in a mixed solvent was studied. The dielectric constant was tuned by regulating the acetone/water volume ratio (R/H ratio) and temperature of the solvent. Hydroxypropyl cellulose (HPC) was used as a steric dispersant. The synthesis were carried out at R/H ratios of 0–4, temperatures of 70–90°C, TiCl₄ concentrations of 0.05–0.2 M, HPC concentrations of 0–5 × 10^–3 g/cm³, and synthesis times of 15–60 min. The TiO₂ particles obtained at an R/H ratio of 0, i.e., pure water system, were fine and agglomerated. In contrast, the TiO₂ particles prepared at an R/H ratio of 3 were uniform and spherical. The TiO₂ particle size increased with increasing TiCl₄ concentration. The synthesis temperature did not influence the particle size, but greatly influenced the morphologyof the TiO₂. Adding HPC to the solution yielded more uniform and spherical particles. In addition, the synthesis time should be longer than 30 min to obtain the most uniform and spherical particles. The dielectric constant of the acetone-water mixed solvent at 28 gave the most uniform and spherical TiO₂ particles. The powders prepared at the condition of 0.1 M TiCl₄, R/H ratio of 3, HPC concentration of 0.001 g/cm³, temperature of 70°C, and synthesis time of 1 h exhibited the most uniform and spherical morphology. The as-synthesized powder was anatase and retained the phase below 400°C. It transformed to the rutile phase after calcination at 700°C.     

Structural Changes in Sol-Gel Derived SiO2 and TiO2 Films by Exposure to Water Vapor

Structural changes in sol-gel derived thin films by exposure to water vapor were investigated using Fourier transform infrared absorption spectroscopy, ellipsometry and x-ray diffraction. We found that SiO₂ gel films were densified with a decrease in OH groups by the exposure at 60°–180°C. The shrinkage and the peak frequency of ₄ (TO) for the exposed films were comparable to those heated in a dry atmosphere at temperatures above 500°C. However, OH groups in the films were not completely removed by the water exposure. A subsequent annealing above 300°C changed the structure of the water-exposed SiO₂ films with condensation of the remaining OH groups. Although the exposed SiO₂ gel films were amorphous, TiO₂ gel films were transformed to anatase with a decrease in OH groups by the treatments at 80°–180°C.     

Band edge emission of ZnS nanoparticles prepared by excess of thiourea as a source of sulfur

This paper reports the study of the preparation and structural characterization of nanocrystalline titanium dioxide (TiO₂) fibers, which were prepared using sol–gel method with titanium tetrachloride (TiCl₄) as the titanium source and acetylacetone as chelating agent to synthesize the poly-acetylacetonatotitanium (PAT) spinning solution, followed by centrifugal spinning and steam atmosphere heat-treatment. The molecule structure of the PAT was analyzed. Using the fourier transform infrared and ¹H nuclear magnetic resonance spectrum. The microstructure of the TiO₂ fibers was observed by using scanning electron microscope, which showed that the fibers’ diameters are in the range of 5–15 μm. The effects of the SiO₂ doping were investigated by using high-resolution transmission electron microscope and X-ray diffractometer, and the conclusion is that SiO₂ doping can efficiently inhibit the grain growth of TiO₂ fibers and defer the phase transformation of anatase-to-rutile. In fact, the grain size is 33.2 nm for the un-doped TiO₂ fibers heat-treated at 700 °C, while the grain size is only 7.6 nm for the TiO₂ fibers doped with 15 wt% SiO₂, which shows the possibility to obtain nano-crystalline anatase TiO₂ fibers at higher heat-treatment temperature.     

Titania-lanthanum phosphate photoactive and hydrophobic new generation catalyst

Titania-lanthanum phosphate nanocomposites with multifunctional properties have been synthesized by aqueous sol-gel method. The precursor sols with varying TiO₂:LaPO₄ ratios were applied as thin coating on glass substrates in order to be transparent, hydrophobic, photocatalytically active coatings. The phase compositions of the composite powders were identified by powder X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HR-TEM). The anatase phase of TiO₂ in TiO₂-LaPO₄ composite precursors was found to be stable even on annealing at 800 °C. The glass substrates, coated with TL1 (TiO₂-LaPO₄ composition with 1 mol% LaPO₄) and TL50 (composite precursor containing TiO₂ and LaPO₄ with molar ratio 1:1) sols and annealed at 400 °C, produced contact angles of 74° and 92°, respectively, though it is only 62° for pure TiO₂ coating. The glass substrates, coated with TL50 sol, produced surfaces with relatively high roughness and uneven morphology. The TL1 material, annealed at 800 °C, has shown the highest UV photoactivity with an apparent rate constant, k_app=24×10⁻³ min⁻¹, which is over five times higher than that observed with standard Hombikat UV 100 (k_app=4×10⁻³ min⁻¹). The photoactivity combined with a moderate contact angle (85.3°) shows that this material has a promise as an efficient self-cleaning precursor.     

The effect of F-doping and temperature on the structural and textural evolution of mesoporous TiO2 powders

Mesoporous F⁻-doped TiO₂ powders were prepared by hydrolysis of titanium tetraisopropoxide (TTIP) in a mixed NH₄F-H₂O solution. Effects of F⁻ ion content and calcination temperatures on the phase composition and porosity of mesoporous titania were investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and BET surface areas. The results showed the BET surface area (S_BET) of the pure and doped powders dried at 100°C ranged from 260 to 310 m²/g as determined by nitrogen adsorption. With increasing calcination temperatures, the S_BET values of the calcined titania powders decreased due to the increase in crystalline size. The pore size distribution was bimodal with fine intra-particle pore and larger inter-particle pore as determined by nitrogen adsorption isotherms. The peak pore diameter of intra-particle pore increases with increasing F⁻ ion content. At 700°C, all the titania powders exhibit monomodal pore size distributions due to the complete collapse of the intra-particle pores. The crystallization of anatase was obviously enhanced due to F⁻-doping at 400°C and 500°C. Moreover, with increasing F⁻ ion concent, F⁻ ions not only suppressed the formation of brookite phase at low temperature, but also prevented phase transition of anatase to rutile at high temperature.