Facile simultaneous polymerization enabled in-situ confinement of size-tailored GeO2 nanocrystals in continuous S-Doped carbons for lithium storage

GeO₂ is a promising anode material for lithium ion batteries due to its high theoretical capacity (1126 mAh g^?1 for reversibly storing 4.4 Li⁺), and moderately low operating voltage (<1.5 V). Nevertheless, the fabrication of truly durable GeO₂ anode with satisfactory rate capability and cycling stability remains a big challenge because of its inherent low conductivity, and the large volume expansion upon charge-discharge that causes severe capacity fading. In this study, an innovative nanostructure with size-adjustable GeO₂ nanoparticles (16–26 nm) embedded in continuous S-doped carbon (GeO₂/S-doped carbon, GSC) has been successfully fabricated via a facile in-situ simultaneous polymerization method followed by heat treatment. The electrochemical results indicate that the as-prepared GSC composites show high reversible capacity (672.9 mAh g^?1 at 50 mA g^?1), superior rate capability (332.9 mAh g^?1 at 1000 mA g^?1), and long-term cycle life (179 mAh g^?1 after 500 cycles at 1000 mA g^?1) as anode materials for lithium ion batteries. The excellent electrochemical performance of GSC nanocomposites could be ascribed to the homogeneous and continuous S-doped carbon matrix, which provides shortened ion diffusion pathway, increased electrical conductivity, enhanced structural stability, and introduced surface/interface property.     

Catalytically Active CoSe2 Supported on Nitrogen-Doped Three Dimensional Porous Carbon as a Cathode for Highly Stable Lithium-Sulfur Battery

Lithium-sulfur batteries are promising secondary energy storage devices that are mainly limited by its unsatisfactory cyclability owing to inefficient reversible conversion of sulfur and lithium sulfide on the cathode during the discharge/charging process. In this study, nitrogen-doped three-dimensional porous carbon material loaded with CoSe₂ nanoparticles (CoSe₂-PNC) is developed as a cathode for lithium-sulfur battery. A combination of CoSe₂ and nitrogen-doped porous carbon can efficiently improve the cathode activity and its conductivity, resulting in enhanced redox kinetics of the charge/discharge process. The obtained electrode exhibits a high discharge specific capacity of 1139.6 mAh g⁻¹ at a current density of 0.2 C. After 100 cycles, its capacity remained at 865.7 mAh g⁻¹ thus corresponding to a capacity retention of 75.97 %. In a long-term cycling test, discharge specific capacity of 546.7 mAh g⁻¹ was observed after 300 cycles performed at a current density of 1 C.     

A Self‐Standing and Flexible Electrode of Yolk–Shell CoS2 Spheres Encapsulated with Nitrogen‐Doped Graphene for High‐Performance Lithium‐Ion Batteries

Flexible lithium‐ion batteries (LIBs) have recently attracted increasing attention with the fast development of bendable electronic systems. Herein, a facile and template‐free solvothermal method is presented for the fabrication of hybrid yolk–shell CoS₂ and nitrogen‐doped graphene (NG) sheets. The yolk–shell architecture of CoS₂ encapsulated with NG coating is designed for the dual protection of CoS₂ to address the structural and interfacial stability concerns facing the CoS₂ anode. The as‐prepared composite can be assembled into a film, which can be used as a binder‐free and flexible electrode for LIBs that does not require any carbon black conducting additives or current collectors. When evaluating lithium‐storage properties, such a flexible electrode exhibits a high specific capacity of 992 mAh g^?1 in the first reversible discharge capacity at a current rate of 100 mA g^?1 and high reversible capacity of 882 mAh g^?1 after 150 cycles with excellent capacity retention of 89.91 %. Furthermore, a reversible capacity as high as 655 mAh g^?1 is still achieved after 50 cycles even at a high rate of 5 C due to the yolk–shell structure and NG coating, which not only provide short Li‐ion and electron pathways, but also accommodate large volume variation.     

Nitrogen-Doped Carbon-Coating Disproportionated SiO Materials as Long Cycling Stable Anode for Lithium Ion Batteries

Silicon monoxide (SiO) is a kind of promising anode material for lithium-ion batteries because of its smaller volume change during the charge and discharge process than pure silicon and its higher theoretical capacity than commercialized graphite. However, its fast-fading capacity still restricts the development of practical application of SiO. A simple and cheap strategy to dope nitrogen and coat carbon on the surface of disproportionated SiO is proposed to improve the cycling stability significantly even at a high specific current. The capacity retention is nearly 85% after 250 cycles and more than 69% after 500 cycles at a specific current of 1000 mA g⁻¹. Even at a specific current of 2000 mA g⁻¹, its cycling performance behaves similarly to that of 1000 mA g⁻¹. Nitrogen doping in materials could improve the conductivity of materials because pyridinic nitrogen and pyrrolic nitrogen could improve the electron conductivity and provide defects to contribute to the diffusion of lithium ions. The use of pitch and melamine, which are easily available industrial raw materials, makes it possible to contribute to the practical application.     

Mitigation of Jahn–Teller distortion and Na+/vacancy ordering in a distorted manganese oxide cathode material by Li substitution

Layered manganese-based oxides are promising candidates as cathode materials for sodium-ion batteries (SIBs) due to their low cost and high specific capacity. However, the Jahn–Teller distortion from high-spin Mn³⁺ induces detrimental lattice strain and severe structural degradation during sodiation and desodiation. Herein, lithium is introduced to partially substitute manganese ions to form distorted P′2-Na_0.67Li_0.05Mn_0.95O₂, which leads to restrained anisotropic change of Mn–O bond lengths and reinforced bond strength in the [MnO₆] octahedra by mitigation of Jahn–Teller distortion and contraction of MnO₂ layers. This ensures the structural stability during charge and discharge of P′2-Na_0.67Li_0.05Mn_0.95O₂ and Na⁺/vacancy disordering for facile Na⁺ diffusion in the Na layers with a low activation energy barrier of ∼0.53 eV. It exhibits a high specific capacity of 192.2 mA h g⁻¹, good cycling stability (90.3% capacity retention after 100 cycles) and superior rate capability (118.5 mA h g⁻¹ at 1.0 A g⁻¹), as well as smooth charge/discharge profiles. This strategy is effective to tune the crystal structure of layered oxide cathodes for SIBs with high performance.

Li-Substitution in P′2-Na_0.67MnO₂ mitigates the anisotropic change of Mn–O bonds and Na/vacancy ordering, and hence significantly promotes its cycling stability and rate capability as a cathode material for sodium-ion batteries.     

Fe3O4/Graphene Composite Anode Material for Fast-Charging Li-Ion Batteries

Composite anode material based on Fe₃O₄ and reduced graphene oxide is prepared by base-catalysed co-precipitation and sonochemical dispersion. Structural and morphological characterizations demonstrate an effective and homogeneous embedding of Fe₃O₄ nanoparticles in the carbonaceous matrix. Electrochemical characterization highlights specific capacities higher than 1000 mAh g⁻¹ at 1C, while a capacity of 980 mAhg⁻¹ is retained at 4C, with outstanding cycling stability. These results demonstrate a synergistic effect by nanosize morphology of Fe₃O₄ and inter-particle conductivity of graphene nanosheets, which also contribute to enhancing the mechanical and cycling stability of the electrode. The outstanding capacity delivered at high rates suggests a possible application of the anode material for high-power systems.     

Highly Porous Carbons Synthesized from Tannic Acid via a Combined Mechanochemical Salt-Templating and Mild Activation Strategy

Highly porous activated carbons were synthesized via the mechanochemical salt-templating method using both sustainable precursors and sustainable chemical activators. Tannic acid is a polyphenolic compound derived from biomass, which, together with urea, can serve as a low-cost, environmentally friendly precursor for the preparation of efficient N-doped carbons. The use of various organic and inorganic salts as activating agents afforded carbons with diverse structural and physicochemical characteristics, e.g., their specific surface areas ranged from 1190 m²·g⁻¹ to 3060 m²·g⁻¹. Coupling the salt-templating method and chemical activation with potassium oxalate appeared to be an efficient strategy for the synthesis of a highly porous carbon with a specific surface area of 3060 m²·g⁻¹, a large total pore volume of 3.07 cm³·g⁻¹ and high H₂ and CO₂ adsorption capacities of 13.2 mmol·g⁻¹ at −196 °C and 4.7 mmol·g⁻¹ at 0 °C, respectively. The most microporous carbon from the series exhibited a CO₂ uptake capacity as high as 6.4 mmol·g⁻¹ at 1 bar and 0 °C. Moreover, these samples showed exceptionally high thermal stability. Such activated carbons obtained from readily available sustainable precursors and activators are attractive for several applications in adsorption and catalysis.     

A Biodegradable Polydopamine‐Derived Electrode Material for High‐Capacity and Long‐Life Lithium‐Ion and Sodium‐Ion Batteries

Polydopamine (PDA), which is biodegradable and is derived from naturally occurring products, can be employed as an electrode material, wherein controllable partial oxidization plays a key role in balancing the proportion of redox‐active carbonyl groups and the structural stability and conductivity. Unexpectedly, the optimized PDA derivative endows lithium‐ion batteries (LIBs) or sodium‐ion batteries (SIBs) with superior electrochemical performances, including high capacities (1818 mAh g^?1 for LIBs and 500 mAh g^?1 for SIBs) and good stable cyclabilities (93 % capacity retention after 580 cycles for LIBs; 100 % capacity retention after 1024 cycles for SIBs), which are much better than those of their counterparts with conventional binders.     

Hierarchical Nanotubes Constructed by Co9S8/MoS2 Ultrathin Nanosheets Wrapped with Reduced Graphene Oxide for Advanced Lithium Storage

Nanostructured hybrid metal sulfides have attracted intensive attention due to their fascinating properties that are unattainable by the single‐phased counterpart. Herein, we report an efficient approach to construct cobalt sulfide/molybdenum disulfide (Co₉S₈/MoS₂) wrapped with reduced graphene oxide (rGO). The unique structures constructed by ultrathin nanosheets and synergetic effects benefitting from bimetallic sulfides provide improved lithium ions reaction kinetics, and they retain good structural integrity. Interestingly, the conductive rGO can facilitate electron transfer, increase the electronic conductivity and accommodate the strain during cycling. When evaluated as anode materials for lithium‐ion batteries (LIBs), the resultant reduced graphene oxide‐coated cobalt sulfide/molybdenum disulfide (Co₉S₈/MoS₂@rGO) nanotubes deliver high specific capacities of 1140, 948, 897, 852, 820, 798 and 784 mAh g^?1 at the various discharging current densities of 0.2, 0.5, 1, 2, 3, 4 and 5 A g^?1, respectively. In addition, they can maintain an excellent cycle stability with a discharge capacity of 807 mAh g^?1 at 0.2 A g^?1 after 70 cycles, 787 mAh g^?1 at 1 A g^?1 after 180 cycles and 541 mAh g^?1 at 2 A g^?1 after 200 cycles. The proposed method may offer fundamental understanding for the rational design of other hybrid functional composites with high Li‐storage properties.     

General Approach to Single and Hybrid Metal Oxide Fiber Structures for High‐Performance Lithium‐Ion Batteries

Owing to the high specific capacity and energy density, metal oxides have become very promising electrodes for lithium‐ion batteries (LIBs). However, poor electrical conductivity accompanied with inferior cycling stability resulting from large volume changes are the main obstacles to achieve a high reversible capacity and stable cyclability. Herein, a facile and general approach to fabricate SnO₂, Fe₂O₃ and Fe₂O₃/SnO₂ fibers is proposed. The appealing structural features are favorable for offering a shortened lithium‐ion diffusion length, easy access for the electrolyte and reduced volume variation when used as anodes in LIBs. As a consequence, both single and hybrid oxides show satisfactory reversible capacities (1206 mAh g^?1 for Fe₂O₃ and 1481 mAh g^?1 for Fe₂O₃/SnO₂ after 200 cycles at 200 mA g^?1) and long lifespans.     

Stabilizing Lithium into Cross‐Stacked Nanotube Sheets with an Ultra‐High Specific Capacity for Lithium Oxygen Batteries

Although lithium–oxygen batteries possess a high theoretical energy density and are considered as promising candidates for next‐generation power systems, the enhancement of safety and cycling efficiency of the lithium anodes while maintaining the high energy storage capability remains difficult. Here, we overcome this challenge by cross‐stacking aligned carbon nanotubes into porous networks for ultrahigh‐capacity lithium anodes to achieve high‐performance lithium–oxygen batteries. The novel anode shows a reversible specific capacity of 3656 mAh g^?1, approaching the theoretical capacity of 3861 mAh g^?1 of pure lithium. When this anode is employed in lithium–oxygen full batteries, the cycling stability is significantly enhanced, owing to the dendrite‐free morphology and stabilized solid–electrolyte interface. This work presents a new pathway to high performance lithium–oxygen batteries towards practical applications by designing cross‐stacked and aligned structures for one‐dimensional conducting nanomaterials.     

A Hierarchically Ordered Mesoporous-Carbon-Supported Iron Sulfide Anode for High-Rate Na-Ion Storage

Sodium-ion batteries (SIBs) are promising alternatives to lithium-based energy storage devices for large-scale applications, but conventional lithium-ion battery anode materials do not provide adequate reversible Na-ion storage. In contrast, conversion-based transition metal sulfides have high theoretical capacities and are suitable anode materials for SIBs. Iron sulfide (FeS) is environmentally benign and inexpensive but suffers from low conductivity and sluggish Na-ion diffusion kinetics. In addition, significant volume changes during the sodiation of FeS destroy the electrode structure and shorten the cycle life. Herein, we report the rational design of the FeS/carbon composite, specifically FeS encapsulated within a hierarchically ordered mesoporous carbon prepared via nanocasting using a SBA-15 template with stable cycle life. We evaluated the Na-ion storage properties and found that the parallel 2D mesoporous channels in the resultant FeS/carbon composite enhanced the conductivity, buffered the volume changes, and prevented unwanted side reactions. Further, high-rate Na-ion storage (363.4 mAh g⁻¹ after 500 cycles at 2 A g⁻¹, 132.5 mAh g⁻¹ at 20 A g⁻¹) was achieved, better than that of the bare FeS electrode, indicating the benefit of structural confinement for rapid ion transfer, and demonstrating the excellent electrochemical performance of this anode material at high rates.     

Hybrid Sub-1 nm Nanosheets of Co-assembled MnZnCuOx and Polyoxometalate Clusters as Anodes for Li-ion Batteries

Transition metal oxide (TMO) anode materials in lithium-ion batteries (LIBs) usually suffer from serious volume expansion leading to the pulverization of structures, further giving rise to lower specific capacity and worse cycling stability. Herein, by introducing polyoxometalate (POM) clusters into TMOs and precisely controlling the amount of POMs, the MnZnCuO_x-phosphomolybdic acid hybrid sub-1 nm nanosheets (MZC-PMA HSNSs) anode is successfully fabricated, where the special electron rich structure of POMs is conducive to accelerating the migration of lithium ions on the anode to obtain higher specific capacity, and the non-covalent interactions between POMs and TMOs make the HSNSs possess excellent structural and chemical stability, thus exhibiting outstanding electrochemical performance in LIBs, achieving a high reversible capacity (1157 mAh g⁻¹ at 100 mA g⁻¹) and an admirable long-term cycling stability at low and high current densities.     

Nitrogen‐Doped Hollow Amorphous Carbon Spheres@Graphitic Shells Derived from Pitch: New Structure Leads to Robust Lithium Storage

Nitrogen‐doped mesoporous hollow carbon spheres (NHCS) consisting of hybridized amorphous and graphitic carbon were synthesized by chemical vapor deposition with pitch as raw material. Treatment with HNO₃ vapor was performed to incorporate oxygen‐containing groups on NHCS, and the resulting NHCS‐O showed excellent rate capacity, high reversible capacity, and excellent cycling stability when tested as the anode material in lithium‐ion batteries. The NHCS‐O electrode maintained a reversible specific capacity of 616 mAh g^?1 after 250 cycles at a current rate of 500 mA g^?1, which is an increase of 113 % compared to the pristine hollow carbon spheres. In addition, the NHCS‐O electrode exhibited a reversible capacity of 503 mAh g^?1 at a high current density of 1.5 A g^?1. The superior electrochemical performance of NHCS‐O can be attributed to the hybrid structure, high N and O contents, and rich surface defects.     

Nanostructured Carbon/Antimony Composites as Anode Materials for Lithium‐Ion Batteries with Long Life

A series of nanostructured carbon/antimony composites have been successfully synthesized by a simple sol–gel, high‐temperature carbon thermal reduction process. In the carbon/antimony composites, antimony nanoparticles are homogeneously dispersed in the pyrolyzed nanoporous carbon matrix. As an anode material for lithium‐ion batteries, the C/Sb10 composite displays a high initial discharge capacity of 1214.6 mAh g^?1 and a reversible charge capacity of 595.5 mAh g^?1 with a corresponding coulombic efficiency of 49 % in the first cycle. In addition, it exhibits a high reversible discharge capacity of 466.2 mAh g^?1 at a current density of 100 mA g^?1 after 200 cycles and a high rate discharge capacity of 354.4 mAh g^?1 at a current density of 1000 mA g^?1. The excellent cycling stability and rate discharge performance of the C/Sb10 composite could be due to the uniform dispersion of antimony nanoparticles in the porous carbon matrix, which can buffer the volume expansion and maintain the integrity of the electrode during the charge–discharge cycles.     

Scalable Synthesis of One-Dimensional Mesoporous ZnMnO3 Nanorods with Ultra-Stable and High Rate Capability for Efficient Lithium Storage

The cost-efficient ZnMnO₃ has attracted increasing attention as a prospective anode candidate for advanced lithium-ion batteries (LIBs) owing to its resourceful abundance, large lithium storage capacity and low operating voltage. However, its practical application is still seriously limited by the modest cycling and rate performances. Herein, a facile design to scalable synthesize unique one-dimensional (1D) mesoporous ZnMnO₃ nanorods (ZMO-NRs) composed of nanoscale particles (≈11 nm) is reported. The 1D mesoporous structure and nanoscale building blocks of the ZMO-NRs effectively promote the transport of ions/electrons, accommodate severe volume changes, and expose more active sites for lithium storage. Benefiting from these appealing structural merits, the obtained ZMO-NRs anode exhibits excellent rate behavior (≈454 mAh g⁻¹ at 2 A g⁻¹) and ultra-long term cyclic performance (≈949.7 mAh g⁻¹ even over 500 cycles at 0.5 A g⁻¹) for efficient lithium storage. Additionally, the LiNi_0.8Co_0.1Mn_0.1O₂//ZMO-NRs full cell presents a practical energy density (≈192.2 Wh kg⁻¹) and impressive cyclability with approximately 91 % capacity retention over 110 cycles. This highlights that the ZMO-NRs product is a highly promising high-rate and stable electrode candidate towards advanced LIBs in electronic devices and sustainable energy storage applications.     

Enhancement of Lithium Storage Performance of Carbon Microflowers by Achieving a High Surface Area

High‐surface‐area, nitrogen‐doped carbon microflowers (A‐NCFs‐4) assembled from porous nanosheets are prepared in a three‐step process: soft‐templating self‐assembly, thermal decomposition, and KOH activation. The hydrazine hydrate used in our experiment serves not only as a structure‐directing agent, but also as a nitrogen source. The resultant A‐NCFs‐4 has a hierarchical porous structure and its specific surface area is as high as 2309 m² g^?1. When used as anode, it exhibits a reversible capacity as high as 807 mAh g^?1 at 300 mA g^?1 after 100 cycles, and an excellent rate capability of 200 mAh g^?1 at a high current density of 8 A g^?1. Compared with unactivated counterpart, A‐NCFs‐4 exhibits a significantly improved lithium storage capacity and rate capability; this can be attributed to its unique structural characteristics and high surface area. The hierarchical micro‐/mesopore structure, high surface area, and nitrogen doping of A‐NCFs‐4 could guarantee fast mass transport for lithium species, enhance the A‐NCFs‐4/electrolyte contact area, shorten the lithium‐ion diffusion length, and accommodate strain induced by volume changes during the electrochemical reaction. The results indicate that the as‐prepared A‐NCFs‐4 could be a promising candidate as a high‐performance anode for lithium‐ion batteries.     

Enhanced Performance of a Lithium–Sulfur Battery Using a Carbonate‐Based Electrolyte

The lithium–sulfur battery is regarded as one of the most promising candidates for lithium–metal batteries with high energy density. However, dendrite Li formation and low cycle efficiency of the Li anode as well as unstable sulfur based cathode still hinder its practical application. Herein a novel electrolyte (1 m LiODFB/EC‐DMC‐FEC) is designed not only to address the above problems of Li anode but also to match sulfur cathode perfectly, leading to extraordinary electrochemical performances. Using this electrolyte, lithium|lithium cells can cycle stably for above 2000 hours and the average Coulumbic efficiency reaches 98.8 %. Moreover, the Li–S battery delivers a reversible capacity of about 1400 mAh g^?1_sulfur with retention of 89 % for 1100 cycles at 1 C, and a capacity above 1100 mAh g^?1_sulfur at 10 C. The more advantages of this cell system are its outstanding cycle stability at 60 °C and no self‐discharge phenomena.     

VOCl as a Cathode for Rechargeable Chloride Ion Batteries

A novel room temperature rechargeable battery with VOCl cathode, lithium anode, and chloride ion transporting liquid electrolyte is described. The cell is based on the reversible transfer of chloride ions between the two electrodes. The VOCl cathode delivered an initial discharge capacity of 189 mAh g^?1. A reversible capacity of 113 mAh g^?1 was retained even after 100 cycles when cycled at a high current density of 522 mA g^?1. Such high cycling stability was achieved in chloride ion batteries for the first time, demonstrating the practicality of the system beyond a proof of concept model. The electrochemical reaction mechanism of the VOCl electrode in the chloride ion cell was investigated in detail by ex situ X‐ray diffraction (XRD), infrared spectroscopy (FTIR), transmission electron microscopy (TEM), and X‐ray photoelectron spectroscopy (XPS). The results confirm reversible deintercalation–intercalation of chloride ions in the VOCl electrode.     

Low-Temperature Synthesis of Honeycomb CuP2@C in Molten ZnCl2 Salt for High-Performance Lithium Ion Batteries

Phosphorus-rich metal phosphides have very high lithium storage capacities, but they are difficult to prepare. A low-temperature phosphorization method based on Mg reducing PCl₃ in ZnCl₂ molten salt at 300 °C is developed to synthesize phosphorus-rich CuP₂@C from a Cu-MOF derived Cu@C composite. Abnormal oxidation of Cu by Zn²⁺ in the molten salt is observed, which leads to the porous honeycomb nanostructure and homogeneously distributed ultrafine CuP₂ nanocrystals. The honeycomb CuP₂@C exhibits excellent lithium storage performance with high reversible capacity (1146 mAh g⁻¹ at 0.2 A g⁻¹) and superior cycling stability (720 mAh g⁻¹ after 600 cycles at 1.0 A g⁻¹), showing the promising application of P-rich metal phosphides in lithium ion batteries.