Electrochemical performance of a three-layer electrode based on Bi nanoparticles,multi-walled carbon nanotube composites for simultaneous Hg(II) and Cu(II) detection

Electrochemical analysis is a promising technique for detecting biotoxic and non-biodegradable heavy metals. This article proposes a novel composite electrode based on a polyaniline (PANi) framework doped with bismuth nanoparticle@graphene oxide multi-walled carbon nanotubes (Bi NPs@GO-MWCNTs) for the simultaneous detection of multiple heavy metal ions. Composite electrodes are prepared on screen-printed electrodes (SPCEs) using an efficient dispensing technique. We used a SM200SX-3A dispenser to load a laboratory-specific ink with optimized viscosity and adhesion to draw a pattern on the work area. The SPCE was used as substrate to facilitate cost-effective and more convenient real-time detection technology. Electrochemical techniques, such as cyclic voltammetry and differential pulse voltammetry, were used to demonstrate the sensing capabilities of the proposed sensor. The sensitivity, limit of detection, and linear range of the PANi-Bi NPs@GO-MWCNT electrode are 2.57 × 10² μA L μmol⁻¹ cm⁻², 0.01 nmol/L, and 0.01 nmol/L–5 mmol/L and 0.15 × 10⁻¹ μA L μmol⁻¹ cm⁻², 0.5 nmol/L, and 0.5 nmol/L–5 mmol/L for mercury ion (Hg(II)) and copper ion (Cu(II)) detection, respectively. In addition, the electrode exhibits a good selectivity and repeatability for Hg(II) and Cu(II) sensing when tested in a complex heavy metal ion solution. The constructed electrode system exhibits a detection performance superior to similar methods and also increases the types of heavy metal ions that can be detected. Therefore, the proposed device can be used as an efficient sensor for the detection of multiple heavy metal ions in complex environments.     

Electrochemical quantification of gold nanoparticles based on their catalytic properties toward hydrogen formation: Application in magnetoimmunoassays

The catalytic ability of gold nanoparticles (AuNPs) toward the formation of H₂ in the electrocatalyzed Hydrogen Evolution Reaction (HER) is thoroughly studied, using screen-printed carbon electrodes (SPCEs) as electrotransducers. The AuNPs on the surface of the SPCE, provide free electroactive sites to the protons present in the acidic medium that are catalytically reduced to hydrogen by applying an adequate potential, with a resulting increment in the reaction rate of the HER measured here by the generated catalytic current. This catalytic current is related with the concentration of AuNPs in the sample and allows their quantification. Finally, this electrocatalytic method is applied for the first time, in the detection of AuNPs as labels in a magnetoimmunosandwich assay using SPCEs as electrotransducers, allowing the determination of human IgG at levels of 1 ng/mL.     

Gold nanoparticles decorated carbon fiber mat as a novel sensing platform for sensitive detection of Hg(II)

The three-dimensional fibril-like carbon fiber mat electrode (CFME) decorated with Au nanoparticles (AuNPs) was employed to construct Hg(II) sensing platform for the first time. The highly porous feature of CFME combining the high affinity of AuNPs for mercury endowed the sensing platform with high sensitivity and good reproducibility. Under optimal conditions, the prepared AuNPs/CFME was capable of sensing Hg(II) with a detection limit of 0.1 μg L^− 1 (S/N = 3) using differential pulse anodic stripping voltammetry (DPASV). Finally, the AuNPs/CFME was successfully demonstrated for the determination of Hg(II) in real water samples with satisfactory results.     

Using flowerlike polymer–copper nanostructure composite and novel organic–inorganic hybrid material to construct an amperometric biosensor for hydrogen peroxide

A new type of amperometric hydrogen peroxide biosensor was fabricated by entrapping horseradish peroxidase (HRP) in the organic–inorganic hybrid material composed of zirconia–chitosan sol–gel and Au nanoparticles (ZrO₂–CS–AuNPs). The sensitivity of the biosensor was enhanced by a flowerlike polymer–copper nanostructure composite (pPA–FCu) which was prepared from co-electrodeposition of CuSO₄ solution and 2,6-pyridinediamine solution. Several techniques, including UV–vis absorption spectroscopy, scanning electron microscopy, cyclic voltammetry, chronoamperometry and electrochemical impedance spectroscopy were employed to characterize the assembly process and performance of the biosensor. The results showed that this pPA–FCu nanostructure not only had excellent redox electrochemical activity, but also had good catalytic efficiency for hydrogen peroxide. Also the ZrO₂–CS–AuNPs had good film forming ability, high stability and good retention of bioactivity of the immobilized enzyme. The resulting biosensors showed a linear range from 7.80 × 10^?7 to 3.7 × 10^?3 mol L^?1, with a detection limit of 3.2 × 10^?7 mol L^?1 (S/N = 3) under optimized experimental conditions. The apparent Michaelis–Menten constant was determined to be 0.32 mM, showing good affinity. In addition, the biosensor which exhibits good analytical performance, acceptable stability and good selectivity, has potential for practical applications.     

Ferrocene-modified Fe3O4@SiO2 magnetic nanoparticles as building blocks for construction of reagentless enzyme-based biosensors

A novel amperometric glucose biosensor was developed by entrapping glucose oxidase (GOD) in chitosan (CS) composite doped with ferrocene monocarboxylic acid-modified magnetic core-shell Fe₃O₄@SiO₂ nanoparticles (FMC-AFSNPs). It is shown that the obtained magnetic bio-nanoparticles attached to the surface of a carbon paste electrode (CPE) with the employment of a permanent magnet showed excellent electrochemical characteristics and at the same time acted as mediator to transfer electrons between the enzyme and the electrode. Under optimal conditions, this biosensor was able to detect glucose in the linear range from 1.0 × 10⁻⁵ to 4.0 × 10⁻³ M with a detection limit of 3.2 μM (S/N = 3). This immobilization approach effectively improved the stability of the electron transfer mediator and is promising for construction of biosensor and bioelectronic devices.     

Ultra-sensitive cholesterol biosensor based on low-temperature grown ZnO nanoparticles

A high-sensitive cholesterol amperometric biosensor based on the immobilization of cholesterol oxidase (ChOx) onto the ZnO nanoparticles has been fabricated which shows a very high and reproducible sensitivity of 23.7 μA mM^?1 cm^?2, detection limit (based on S/N ratio) 0.37 ± 0.02 nM, response time less than 5 s, linear range from 1.0 to 500.0 nM and correlation coefficient of R = 0.9975. A relatively low value of enzyme’s kinetic parameter (Michaelis–Menten constant) ～4.7 mM has been obtained which indicates the enhanced enzymatic affinity of ChOx to Cholesterol. To the best of our knowledge, this is the first report in which such a very high-sensitivity and low detection limit has been achieved for the cholesterol biosensor by using ZnO nanostructures modified electrodes.     

Electrochemical sensing of hydroxylamine by gold nanoparticles on single-walled carbon nanotube films

The arrays of gold nanoparticles (AuNPs) were fabricated on flexible and transparent single-walled carbon nanotube (SWCNT) films using the electrochemical deposition method, and the patterned nanotubes were then used as electrodes for hydroxylamine detection. The sizes and densities of the AuNPs could easily be controlled by varying the amount of charge deposited, and the gold-deposited area showed a homogeneous distribution on the exposed SWCNT film surface. X-ray diffraction analysis of the AuNPs shows a face-centered cubic structure that is dominated by the lowest energy {111} facets. The oxidation of the hydroxylamine on the AuNP-deposited SWCNT films depended strongly on the solution pH, and the maximum catalytic current was observed at a pH of 9.0. A linear electrical response was observed for concentrations ranging from 0.016 to 0.210 mM, and the detection limit and the sensitivity were 0.72 μM and 165.90 μAmM^?1 cm^?2, respectively. Moreover, the amperometric response in hydroxylamine showed a stable response for a long time (300 s), during which time it retained 94% of its initial value. In the long-term storage stability test, the current response to hydroxylamine decreased slightly, with only 17% leakage after 30 days.     

Microwave-radiated synthesis of gold nanoparticles/carbon nanotubes composites and its application to voltammetric detection of trace mercury(II)

Gold nanoparticles/carbon nanotubes (Au-NPs/CNTs) composites were rapidly synthesized by microwave radiation, and firstly applied for the determination of trace mercury(II) by anodic stripping voltammetry (ASV). The structure and composition of the synthesized Au-NPs/CNTs nanocomposites were characterized by transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDX), UV–vis absorption spectroscopy and cyclic voltammetry. Au-NPs/CNTs nanocomposites modified glassy carbon electrode (Au-NPs/CNTs/GCE) exhibited excellent performance for Hg(II) analysis. A wide linear range (5 × 10⁻¹⁰–1.25 × 10⁻⁶ mol/L) and good repeatability (relative standard deviation of 1.84%) were obtained for Hg(II) detection. The limit of detection was found to be 3 × 10⁻¹⁰ mol/L (0.06 μg/L) at 2 min accumulation, while the World Health Organization’s guideline value of mercury for drinking water is 1 μg/L, suggesting the proposed method may have practical utility.     

A plasmonic mercury sensor based on silver–gold alloy nanoparticles electrodeposited on indium tin oxide glass

We construct silver–gold alloy nanoparticles (Ag–AuNPs) as the basis of a reagentless, sensitive and simple mercury sensor. Ag–AuNPs were electrodeposited directly on transparent indium tin oxide film coated glass. Hg(II) ions in aqueous solution could be reduced by Ag atoms existing in Ag–AuNPs; the deposition/amalgamation of Hg on the nanoparticles resulted in a blue shift of the localized surface plasmon resonance peak. Therefore, Hg^2 + can be detected quantitatively by using a spectrophotometer. The sensor response is linear in the range from 0.05 to 500 ppb of Hg(II) concentration. No sample separation or preconcentration is required for detection of ultralow levels of mercury in water samples. The results shown herein have potential applications in the development of a new optical sensor for the detection of low concentrations of mercury.     

Copper film electrode for anodic stripping voltammetric determination of trace mercury and lead

A novel in-situ prepared copper film electrode (CuFE) for anodic stripping voltammetric measurement of trace levels of Hg(II) and Pb(II) is presented. The optimal electroanalytical performance of the CuFE was achieved in electrolyte solution comprising 0.1 M HCl and 0.4 M NaCl. The CuFE exhibited excellent operation in the presence of dissolved oxygen with calculated LoD of 0.1 μg L^− 1 Hg(II) and 0.06 μg L^− 1 Pb(II) in combination with 300 s accumulation time, repeatability with RSD of 4.5% for Hg(II) and 0.9% for Pb(II) (n = 12), and favourable linear response in the examined concentration range of 10–100 μg L^− 1 (R² = 0.997) for Hg and 5–70 μg L^− 1 (R² = 0.999) for Pb after 120 s accumulation. The electrode enabled also simultaneous detection of both investigated metal ions and revealed promising electroanalytical characteristics similar to or in certain cases surpassing those of commonly used gold electrodes.     

Direct electrochemistry of hemoglobin at vertically-aligned self-doping TiO2 nanotubes: A mediator-free and biomolecule-substantive electrochemical interface

The present work is dedicated to making the best of vertically-aligned TiO₂ nanotubes (TNTs) array to serve as a prospectively ideal “vessel” for protein immobilization and biosensor applications. The TNTs fabricated by electrochemical anodizing possess the advantageous of perpendicular alignment and tailored tubular architecture, as well as the good biocompatibility and hydrophilicity. But the electron-transfer resistance of the as-grown (AG-) TNTs is too large for the direct electron transfer and electrochemical biosensing. A simple strategy on controllable electrochemical reduction treatment of TNTs is adopted on it, leading TNTs in situ self-doped with Ti(III), which makes the Ti(III)–TNTs much better conductivity while the tubular and crystal structure of TNTs array still well maintained. Results show that the TNTs can be used as a super vessel for rapid and substantive immobilization of hemoglobin (Hb), with a large surface electroactive Hb coverage (Γ*) of 1.5 × 10^?9 mol cm^?2. The enhanced direct electron transfer of Hb is commendably observed on the Ti(III)–TNTs/Hb biosensor with a couple of well-defined redox peaks compared with the AG-TNTs/Hb. The biosensor further exhibits fast response, high sensitivity and stability for the amperometric biosensing of H₂O₂ with the detection limit of 1.5 × 10^?6 M, and the apparent Michaelis–Menten constant of 1.02 mM.     

A disposable impedance sensor for electrochemical study and monitoring of adhesion and proliferation of K562 leukaemia cells

A polyaniline-modified screen-printed carbon electrode (PANI/SPCE) was prepared by electropolymerization for the construction of a novel disposable cell impedance sensor. The conductive polymer improved greatly the electron transfer of SPCE and was very effective for cell immobilization. The adhesion of cells increased the electron transfer resistance (R_et) of redox probe on the PANI/SPCE surface, producing an impedance sensor for K562 leukaemia cells with a semilogarithm linear range from 10⁴ to 10⁷ cells ml⁻¹ and a limit of detection of 8.32 × 10³ cells ml⁻¹ at 10σ. The proliferation of cells on the conductive polymer increased the R_et, leading to a novel way to monitor the growth process of cells on the PANI/SPCE. The electrochemical monitoring indicated K562 leukaemia cells cultured in vitro on the PANI surface were viable for 60 h, consistent with the analysis from microscopic imaging and MTT assay. This method for monitoring the surface proliferation and detecting the number of viable cells was simple, low-cost and disposable, thus providing a convenient avenue for electrochemical study of cell immobilization, adhesion, proliferation and apoptosis.     

Amperometric ascorbic acid biosensor based on carbon nanoplatelets derived from ground cherry husks

In this work, a novel amperometric biosensor based on carbon nanoplatelets derived from ground cherry (Physalis peruviana) husks (GCHs-CNPTs) is reported for the sensitive and selective detection of ascorbic acid (AA). The structure of the nanoplatelets, the oxygen-containing groups and edge-plane-like defective sites (EPDSs) on the GCHs-CNPTs were characterized by scanning electron microscopy, X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. The presence of GCHs-CNPTs with a high density of EPDSs effectively enhances the electron transfer between AA and the glassy carbon electrode (GCE), and thus induces a substantial decrease in the overvoltage for AA oxidation compared with both a bare GCE and a GCE modified with carbon nanotubes (CNTs/GCE). In particular, an amperometric biosensor based on GCHs-CNPTs exhibited a wider linear range (0.01–3.57 mM), higher sensitivity (208.63 μA mM^− 1 cm^− 2), a lower detection limit (1.09 μM, S/N = 3) and better resistance to fouling for AA determination compared to a CNTs/GCE. The great potential of the GCHs-CNPTs/GCE for practical and reliable AA analysis was demonstrated by the successful determination of AA in samples taken from a medical injection dose and a soft drink.     

Electrochemical biosensor based on hairpin DNA probe using 2-nitroacridone as electrochemical indicator for detection of DNA species related to Chronic Myelogenous Leukemia

In this article, a new kind of hairpin DNA Electrochemical biosensor using nitroacridone as electrochemical indicator was first designed, and used to detect BCR/ABL fusion gene in Chronic Myelogenous Leukemia (CML). The results indicated that in pH 7.0 Tris–HCl buffer solution, the oxidation peak current was linear with the concentration of complementary strand in the range of 6.2 × 10⁻⁸–3.1 × 10⁻⁷ mol/l with a detection limit of 5.3 × 10⁻⁹ mol/l. This new hairpin DNA electrochemical biosensor demonstrates its excellent specificity for single-base mismatch and complementary (dsDNA) after hybridization, and this probe has been used for assay of PCR product of a real sample with satisfactory result.     

Synthesis,characterizations of silica-coated gold nanorods and its applications in electroanalysis of hemoglobin

Gold nanorods (GNRs) were synthesized by a seed–mediated growth approach followed by TEOS polymerization leading to the formation of silica layer surrounding the gold nanorod core. TEM images showed that the silica-coated gold nanorods (GNRs@SiO₂) were dispersed with an average aspect ratio of 3.1 for the GNRs cores and a uniform thickness of the silica shell. The core/shell nanocomposites were further used as efficient supports for the immobilization of hemoglobin (Hb) to fabricate a novel biosensor. The immobilized Hb showed an enhanced electron transfer for its heme Fe(III) to Fe(II) redox couple. This biosensor showed an excellent bioelectrocatalytic activity towards H₂O₂ with a linear range from 8.0 × 10⁻⁷ to 6.1 × 10⁻⁵ M, and the detection limit was 6.0 × 10⁻⁸ M at 3σ. The apparent Michaelis–Menten constant of the immobilized hemoglobin was calculated to be 0.13 mM.     

High performance bioanode based on direct electron transfer of fructose dehydrogenase at gold nanoparticle-modified electrodes

The direct electron transfer reaction of fructose dehydrogenase (FDH) from Gluconobacter sp. on alkanethiol-modified gold nanoparticles (AuNPs) was examined. AuNP-modified electrodes were simply fabricated by depositing citrate-reduced gold nanoparticles onto a gold electrode and carbon fiber paper and then covering the surface with a self-assembled monolayer of alkanethiols. The immobilization of AuNPs provided a large effective surface area for the adsorption of FDH. Catalytic oxidation currents based on the direct electron transfer reaction of FDH were observed from a potential about ?100 mV (vs. Ag/AgCl, 3 M NaCl) in the presence of d-fructose without a mediator. The current density reached as high as 14.3 ± 0.93 mA/cm² (at +500 mV), which was achieved in the presence of 200 mM d-fructose by immobilization of FDH on 2-mercaptoethanol-modified AuNP/carbon fiber paper electrodes.     

Quantum dot-based electrochemical DNA biosensor using a screen-printed graphite surface with embedded bismuth precursor

This work reports the development of screen-printed quantum dots (QDs)-based DNA biosensors utilizing graphite electrodes with embedded bismuth citrate as a bismuth precursor. The sensor surface serves both as a support for the immobilization of the oligonucleotide and as an ultrasensitive voltammetric QDs transducer relying on bismuth nanoparticles. The utility of this biosensor is demonstrated for the detection of the C634R mutation through hybridization of the biotin-tagged target oligonucleotide with a surface-confined capture complementary probe and subsequent reaction with streptavidin-conjugated PbS QDs. The electrochemical transduction step involved anodic stripping voltammetric determination of the Pb(II) released after acidic dissolution of the QDs. Simultaneously with the electrolytic accumulation of Pb on the sensor surface, the embedded bismuth citrate was converted in situ to bismuth nanoparticles enabling ultra-trace Pb determination. The biosensor showed a linear relationship of the Pb(II) peak current with respect to the logarithm of the target DNA concentrations from 0.1 pmol L^− 1 to 10 nmol L^− 1, and the limit of detection was 0.03 pmol L^− 1. The biosensor exhibited effective discrimination between a single-base mismatched sequence and the fully complementary target DNA. These “green” biosensors are inexpensive, lend themselves to easy mass production, and hold promise for ultrasensitive bioassay formats.     

Enhanced Raman spectroscopy coupled to chemometrics for identification and quantification of acetylcholinesterase inhibitors

In this work, we present a new complete method using Surface Enhanced Raman Spectroscopy (SERS) and chemometrics for the qualitative and quantitative detection of pesticides by measuring the acetylcholinesterase (ACHE) activity. The Raman SERS is not only used for measuring the ACHE activity, but also for the direct detection of pesticides individually and for their identification. Gold nanoparticles (AuNPs) were used as dynamic SERS substrates for sensitive monitoring of ACHE activity in the presence of very low levels of organophosphate and carbamate pesticides, chemical warfare agents that are known to be ACHE inhibitors. The lowest detectable level for paraoxon was determined at 4.0 × 10⁻¹⁴ M and 1.9 × 10⁻⁹ M for carbaryl. The use of the enzyme allowed limits of detection for both pesticides that were much lower than the limits obtained by direct SERS analysis of the pesticides. The system shows a linear relationship between the intensity band at 639 cm⁻¹ and pesticide concentration. These results suggest that this biosensor could be used in the future for the non-selective detection of all ACHE inhibitors at very low concentrations with possible identification of the inhibitor.     

An insight to the filtration mechanism of Pb(II) at the surface of a clay ceramic membrane through its preconcentration at the surface of a graphite/clay composite working electrode

The use of cyclic voltammetry (CV) and linear scan anodic stripping voltammetry (LSASV) to predict the selectivity of microfiltration ceramic membranes made from a lump of local clay towards Pb(II) ions filtration is described. The membranes were characterized by different techniques followed by CV analysis of the Fe(CN)₆^3-/Fe(CN)₆^4- redox couple and Pb(II) on bare graphite, raw clay, and clay-modified carbon paste electrode (clay-modified CPE). The effect of clay loading in the range of 1–10 % (w/w) on the electrodes is studied, where an enhanced peak current is observed for 5 % w/w clay. Moreover, a decrease in the peak current can be seen for bare graphite electrodes, suggesting that the clay mineral had played a substantial role in the sieving of heavy metal ions through the ceramic membrane. The electroactive surface area of 5% w/w raw clay towards Fe(II) ions was found to be in the order of 3.07 × 10^-2 cm² and higher than 5% w/w clay sintered to 1000 °C and bare graphite. CV analysis shows that both, 5 % w/w raw clay and 5 % w/w clay sintered to 1000 °C exhibited high peak currents towards Pb(II) ions. The mobility of the Pb(II) ions is found to increase when 5% w/w clay sintered to 1000 °C is utilized as membrane/electrode, leading to an increase in the amount of reduced Pb(II) ions on the surfaces of the clay membranes/electrodes. The study suggests successful filtration of Pb(II) ions through the proposed membrane/electrode and a much better accumulation than Fe(II) at the surface of the membrane/electrode before being subjected to filtration.     

Amperometric biosensors based on deposition of gold and platinum nanoparticles on polyvinylferrocene modified electrode for xanthine detection

In this study, new xanthine biosensors, XO/Au/PVF/Pt and XO/Pt/PVF/Pt, based on electroless deposition of gold(Au) and platinum(Pt) nanoparticles on polyvinylferrocene(PVF) coated Pt electrode for detection of xanthine were presented. The amperometric responses of the enzyme electrodes were measured at the constant potential, which was due to the electrooxidation of enzymatically produced H₂O₂. Compared with XO/PVF/Pt electrode, XO/Au/PVF/Pt and XO/Pt/PVF/Pt exhibited excellent electrocatalytic activity towards the oxidation of the analyte. Effect of Au and Pt nanoparticles was investigated by monitoring the response currents at the different deposition times and the different concentrations of KAuCl₄ and PtBr₂. Under the optimal conditions, the calibration curves of XO/Au/PVF/Pt and XO/Pt/PVF/Pt were obtained over the range of 2.5 × 10^?3 to 0.56 mM and 2.0 × 10^?3 to 0.66 mM, respectively. The detection limits were 7.5 × 10^?4 mM for XO/Au/PVF/Pt and 6.0 × 10^?4 mM for XO/Pt/PVF/Pt. The effects of interferents, the operational and the storage stabilities of the biosensors and the applicabilities of the proposed biosensors to the drug samples analysis were also evaluated.