Preparation and electrochemical lithium storage of flower-like spinel Li4Ti5O12 consisting of nanosheets

In this paper, flower-like spinel Li₄Ti₅O₁₂ consisting of nanosheets was synthesized by a hydrothermal process in glycol solution and following calcination. The as-prepared product was characterized by scanning electron microscopy, transmission electron microscopy, X-ray powder diffraction and cyclic voltammetry. The capacity of the sample used as anode material for lithium ion battery was measured. This structured Li₄Ti₅O₁₂ exhibited a high reversible capacity and an excellent rate capability of 165.8 m Ahg⁻¹ at 8 C, indicating potential application for lithium ion batteries with high rate performance and high capacity.     

High rate performance of lithium manganese nitride and oxynitride as negative electrodes in lithium batteries

The performance of Li_7.9MnN_3.2O_1.6 and Li₇MnN₄ as electrode materials in lithium batteries was analyzed. At 1C rate, capacities of 180 and 230 mAh/g, respectively, were obtained after 50 cycles. If the first charge is done at 0.1C, outstanding capacities of 120–135 mAh/g are observed after 100 cycles at 5C. More lithium can be removed during the charge at 0.1C, leading to a large amount of lithium vacancies that enhance mobility and rate capability. It is proposed that incomplete filling of the vacancies occurs upon cycling, so that the mobility remains high. This performance compares well to that of Li₄Ti₅O₁₂.     

High-energy and high-power Li-rich nickel manganese oxide electrode materials

A lithium-rich nickel-manganese oxide compound Li_x(Ni_0.25Mn_0.75)O_y (x > 1) was synthesized from layered Na_0.9Li_0.3Ni_0.25Mn_0.75O_δ precursor using a lithium ion-exchange reaction. The electrochemical behavior of the material as a cathode for lithium batteries, and a preliminary discussion of its structure are reported. The product Li_1.32Na_0.02Ni_0.25Mn_0.75O_y (IE-LNMO) shows broad X-ray diffraction peaks, but possesses a high intensity sharp (003) layering peak and multiple peaks with intensity in the 20–23° 2θ region which suggest Ni–Mn ordering in the transition metal layer (TM). Li/IE-LNMO cells demonstrate very stable reversible capacities of 220 mAh/g @ 15 mA/g and possess extremely high power of 150 mAh/g @ 1500 mA/g (15C). The Li/IE-LNMO cell dQ/dV plot exhibits three reversible electrochemical processes due to Ni/Mn redox behavior in a layered component, and Mn redox exchange in a spinel component. No alteration in the dQ/dV curves and no detectable change in the voltage profiles over 40 cycles were observed, thus indicating a stable structure for lithium insertion/extraction. This new material is attractive for demanding Li-ion battery applications.     

High-capacity LiV3O8 thin-film cathode with a mixed amorphous–nanocrystalline microstructure prepared by RF magnetron sputtering

LiV₃O₈ thin films with a mixed amorphous–nanocrystalline microstructure were deposited on stainless steel substrates using radio-frequency (RF) magnetron sputtering for the first time. The films exhibited good performance as a cathode material for lithium ion batteries. Results indicate that the film electrodes had a smooth surface and consisted mainly of an amorphous structure containing nanocrystalline zones dispersed within it. Depending on its microstructure, the films delivered an initial discharge capacity as high as 382 mAh/g and exhibited good capacity retention, with discharge capacity of 301 mAh/g after 100 cycles representing a loss rate of 0.21% per cycle.     

LiMn2O4 hollow nanosphere electrode material with excellent cycling reversibility and rate capability

Lithium-rich Li_1.05Mn₂O₄ hollow nanospheres have been successfully prepared by air-calcining lithiated MnO₂ precursor at a low temperature of 550 °C, which was synthesized by chemical lithiation of hollow MnO₂ nanospheres with LiI at 70 °C for 12 h. The lithium-rich Li_1.05Mn₂O₄ hollow nanospheres exhibit an excellent cycling stability and rate capability as a cathode material for rechargeable lithium batteries: it maintains 90% of its initial capacity after 500 cycles, and keeps 70% of the reversible capacity at 0.1 C rat, even at 15 C rate.     

Electrode reactions of manganese oxides for secondary lithium batteries

Nanorods of MnO₂, Mn₃O₄, Mn₂O₃ and MnO are synthesized by hydrothermal reactions and subsequent annealing. It is shown that though different oxides experience distinct phase transition processes in the initial discharge, metallic Mn and Li₂O are the end products of discharge, while MnO is the end product of recharge for all these oxides between 0.0 and 3.0 V vs. Li⁺/Li. Of these 4 manganese oxides, MnO is believed the most promising anode material for lithium ion batteries while MnO₂ is the most promising cathode material for secondary lithium batteries.     

A hierarchical micro/nanostructured 0.5Li2MnO3·0.5LiMn0.4Ni0.3Co0.3O2 material synthesized by solvothermal route as high rate cathode of lithium ion battery

A hierarchical micro/nanostructured Li-rich layered 0.5Li₂MnO₃·0.5LiMn_0.4Ni_0.3Co_0.3O₂ (H-LMNCO) material is prepared for the first time through the development of a solvothermal method, and served as cathode of lithium ion batteries. Electrochemical tests indicate that the H-LMNCO exhibits both a high reversible capacity and an excellent rate capability. The reversible discharge capacity of the H-LMNCO has been measured as high as 300.1 mAh·g^− 1 at 0.2 C rate. When the rate is increased to 10 C, the discharge capacity could still maintain a high value of 163.3 mAh·g^− 1. The results demonstrate that the developed solvothermal route is a novel synthesis strategy of preparing high rate performance Li-rich layered cathode material for lithium ion batteries.     

Reversible lithium storage in Na2Li2Ti6O14 as anode for lithium ion batteries

The sodium lithium titanate with composition Na₂Li₂Ti₆O₁₄ has been synthesized by a sol–gel method. Thermogravimetric analysis and differential thermal analysis (TG–DTA) of the thermal decomposition process of the precursor and X-ray diffraction (XRD) data indicate the crystallization of sodium lithium titanate has occurred at about 600 °C. Electrochemical lithium insertion into Na₂Li₂Ti₆O₁₄ for lithium ion battery has been investigated for the first time. These results indicate the discharge and charge potential plateaus are about 1.3 V. The initial discharge capacity is much higher than the charge capacity and irreversible capacity exists in the voltage window 1–3 V. Subsequently, the discharge capacity decreases slowly, but the charge capacity increases slightly in the following cycles. After a few cycles, the specific capacity remains almost constant values and the sample exhibits the excellent retention of capacity on cycling.     

Enhancing the rate capability of high capacity xLi2MnO3 · (1 − x)LiMO2 (M = Mn,Ni, Co) electrodes by Li–Ni–PO4 treatment

The rate capability of high capacity xLi₂MnO₃ · (1 ? x)LiMO₂ (M = Mn, Ni, Co) electrodes for lithium-ion batteries has been significantly enhanced by stabilizing the electrode surface by reaction with a Li–Ni–PO₄ solution, followed by a heat-treatment step. Reversible capacities of 250 mAh/g at a C/11 rate, 225 mAh/g at C/2 and 200 mAh/g at C/1 have been obtained from 0.5Li₂MnO₃ · 0.5LiNi_0.44Co_0.25Mn_0.31O₂ electrodes between 4.6 and 2.0 V. The data bode well for their implementation in batteries that meet the 40-mile range requirement for plug-in hybrid vehicles.     

A novel anode material of antimony nitride for rechargeable lithium batteries

Antimony nitride thin film has been successfully fabricated by magnetron sputtering method and its electrochemistry with lithium was investigated for the first time. The reversible discharge capacity of Sb₃N/Li cells cycled between 0.3 V and 3.0 V was found above 600 mAh/g. By using transmission electron microscopy and selected area electron diffraction measurements, the conversion reaction of Sb₃N into Li₃Sb and Li₃N was revealed during the lithium electrochemical reaction of Sb₃N thin film electrode. The high reversible capacity and the good cycleability made Sb₃N one of promising anode materials for future rechargeable lithium batteries.     

High capacity Li[Li0.2Mn0.54Ni0.13Co0.13]O2–V2O5 composite cathodes with low irreversible capacity loss for lithium ion batteries

With an aim to suppress the huge irreversible capacity loss encountered in high capacity layered oxide solid solutions between Li₂MnO₃ and LiMO₂ (M = Mn, Ni, and Co), layered Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂–V₂O₅ composite cathodes with various V₂O₅ contents have been investigated. The irreversible capacity loss decreases from 68 mAh/g at 100% Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ to 0 mAh/g around 89 wt.% Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂–11 wt.% V₂O₅ as the lithium-free V₂O₅ serves as an insertion host to accommodate the lithium ions that could not be inserted back into the layered lattice after the first charge. The Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂–V₂O₅ composite cathodes with about 10–12 wt.% V₂O₅ exhibit an attractive discharge capacity of close to 300 mAh/g with little irreversible capacity loss and good cyclability.     

A disordered rock-salt Li-excess cathode material with high capacity and substantial oxygen redox activity: Li1.25Nb0.25Mn0.5O2

A disordered rocksalt Li-excess cathode material, Li_1.25Nb_0.25Mn_0.5O₂, was synthesized and investigated. It shows a large initial discharge capacity of 287 mAh g^− 1 in the first cycle, which is much higher than the theoretical capacity of 146 mAh g^− 1 based on the Mn³⁺/Mn⁴⁺ redox reaction. In situ X-ray diffraction (XRD) demonstrates that the compound remains cation-disordered during the first cycle. Electron energy loss spectroscopy (EELS) suggests that Mn and O are likely to both be redox active, resulting in the large reversible capacity. Our results show that Li_1.25Nb_0.25Mn_0.5O₂ is a promising cathode material for high capacity Li-ion batteries and that reversible oxygen redox in the bulk may be a viable way forward to increase the energy density of lithium-ion batteries.     

Tremella-like molybdenum dioxide consisting of nanosheets as an anode material for lithium ion battery

Tremella-like structured MoO₂ consisting of nanosheets was obtained via a Fe₂O₃-assisted hydrothermal reduction of MoO₃ in ethylenediamine aqueous solution. The as-prepared product was characterized and tested with scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS), cyclic voltammetry (CV) and capacity measurement as anode material for lithium ion batteries. This structured MoO₂ shows very high reversible capacity (>600 mA h g⁻¹), good rate capability and cycling performance, presenting potential application as anode material for lithium ion batteries with high rate capability and high capacity.     

High-performance Na1.25V3O8 nanosheets for aqueous zinc-ion battery by electrochemical induced de-sodium at high voltage

Aqueous rechargeable zinc-ion batteries (ARZIBs) are expected to replace organic electrolyte batteries owing to its low price, safe and environmentally friendly characteristics. Herein, we fabricated vanadium-based Na_1.25V₃O₈ nanosheets as a cathode material for ARZIBs, which present a high performance by electrochemical de-sodium at high voltage to form Na₂V₆O₁₆ phase in the first cycle: high capacity of 390 mAh/g at 0.1 A/g, high rate performance (162 mAh/g at 10 A/g) and superior cycle stability (179 mAh/g with a high capacity retention of 88.2% of the maximum capacity after 2000 cycles). In addition, the cell exhibits a high energy density of 416.9 Wh/kg at 143.6 W/kg, suggesting great potential of the as-prepared Na_1.25V₃O₈ nanosheets for ARZIBs     

Low charge overpotentials and extended full cycling capability in lithium-oxygen batteries by controlling the nature of discharge products

Hollow NiCo₂O₄ microspheres with a highly hierarchical porous structure were synthesized and conducted as catalysts for lithium-oxygen batteries. The influence of NiCo₂O₄ on the discharge products was investigated. The NiCo₂O₄ showed the capability to promote the formation of lithium deficient Li_2 − xO₂ and exerted a significant influence on the electrochemical performance of lithium-oxygen batteries with a low charge overpotential and extended full cycling over 50 cycles.     

Electrospun nano-vanadium pentoxide cathode

Nanocrystallites of vanadium pentoxide were synthesized by the hydrothermal treatment of electrospun composite nanofibers. Each crystallite of dimension ?100 nm was found to be a single crystal of δ-phase H_xV₄O₁₀ · nH₂O. The crystallinity and morphology was maintained on heating to 500 °C when V₂O₅ was formed. The electrochemical capacity of the nano-V₂O₅ in a lithium cell was found to be above 350 mAh/g. The columbic efficiency is close to 100% when small amounts of lithium bis(oxalato)borate is added to the LiPF₆ electrolyte.     

Nano-LiCoO2 as cathode material of large capacity and high rate capability for aqueous rechargeable lithium batteries

Crystalline nanoparticles of LiCoO₂ are prepared by a sol–gel method at 550 °C and characterized by X-ray diffraction. Their electrochemical behaviors were characterized by cyclic voltammograms, capacity measurement and cycling performance. Results show that the reversible capacity of the nano-LiCoO₂ can be up to 143 mAh/g at 1000 mA/g and still be 133 mAh/g at 10,000 mA/g (about 70C) in 0.5 mol/l Li₂SO₄ aqueous electrolyte. In addition, their cycling behavior is also very satisfactory, no evident capacity fading during the initial 40 cycles. These data present great promise for the application of aqueous rechargeable lithium batteries.     

Structural and electrochemical investigation of Li2MgSnO4 anode for lithium batteries

Hexagonal Li₂MgSnO₄ compound was synthesized at 800 °C using Urea Assisted Combustion (UAC) method and the same has been exploited as an anode material for lithium battery applications. Structural investigations through X-ray diffraction, Fourier Transform Infra Red spectroscopy and ⁷Li NMR (Nuclear Magnetic Resonance spectroscopy) studies demonstrated the existence of hexagonal crystallite structure with a = 6.10 and c = 9.75. An average crystallite size of ∼400 nm has been calculated from PXRD pattern, which was further evidenced by SEM images. An initial discharge capacity of ∼794 mA h/g has been delivered by Li₂MgSnO₄ anode with an excellent capacity retention (85%) and an enhanced coulombic efficiency (97–99%). Further, the Li₂MgSnO₄ anode material has exhibited a steady state reversible capacity of ∼590 mA h/g even after 30 cycles, thus qualifying the same for use in futuristic lithium battery applications.     

Tunable lithium storage properties of metal lithium titanates by stoichiometric modulation

A simple stoichiometric modulation of Na_2 − 2xSr_xLi₂Ti₆O₁₄ was developed to achieve tunable electrochemical properties of the material. The concept was confirmed experimentally and theoretically using density functional theory (DFT) calculations. Both the operating potential and the amount of reversibly intercalated lithium ions were manipulated by simply changing the Na/Sr ratio. These unique characteristics originated from a gradual change in the electron density on the Ti atoms and the extra lithium insertion sites at SrLi₂Ti₆O₁₄. As a promising anode material for lithium-ion batteries, Na_2 − 2xSr_xLi₂Ti₆O₁₄ and its tunable electrochemical properties have significant importance in terms of the development of tailored electrodes with desirable electrochemical performance.     

LixV2O5 nanobelts for high capacity lithium-ion battery cathodes

5–10 μm long, typically 200–300 nm wide, and several nanometers thick Li_xV₂O₅ (× ～ 0.8) nanobelts with the δ-type crystal structure were synthesized by a hydrothermal treatment of Li⁺-exchanged V₂O₅ gel. When dried at 200 °C under vacuum prior to electrochemical testing, the as-prepared nanobelts underwent the well-known δ → ε → γ-phase transition giving a mixture of ε and γ phases as a nanocomposite electrode material. Such a simple preparation procedure guarantees a yield of material with drastically enhanced initial discharge specific capacity of 490 mAh/g and great cyclability. The enhanced electrochemical performance is attributed to the complex of experimental procedures including post-synthesis treatment of the single-crystalline Li_xV₂O₅ nanobelts.