Nb2O5 nanobelts: A lithium intercalation host with large capacity and high rate capability

In this study, Nb₂O₅ nanobelts, with a ca. ∼15 nm in thickness, ca. ∼60 nm in width and several tens of mircrometers in length, have first been used as the electrode material for lithium intercalation over the potential window of 3.0–1.2 V (vs. Li⁺/Li). It delivers an initial intercalation capacity of 250 mA hg⁻¹ at 0.1 Ag⁻¹ current density, corresponding to x = 2.5 for L_xNb₂O₅, and can still keep relative stable and reaches as large as 180 mA hg⁻¹ after 50 cycles. Surprisingly, the electrodes composed of Nb₂O₅ nanobelts can work smoothly even at high current density of 10 Ag⁻¹, and shows higher specific capacity and excellent cycling stable, as well as sloped feature in voltage profile. Cycling test indicates Nb₂O₅ nanobelts electrode shows a high reversible charge/discharge capacity, high rate capability with excellent cycling stability.     

Lithium storage in hollow spherical ZnFe2O4 as anode materials for lithium ion batteries

Hollow microspheres composed of phase-pure ZnFe₂O₄ nanoparticles (hierarchically structured) have been prepared by hydrothermal reaction. The unique hollow spherical structure significantly increases the specific capacity and improves capacity retention of this material. The product of each phase transition during initial discharge (ZnFe₂O₄ ? Li_0.5ZnFe₂O₄ ? Li₂ZnFe₂O₄ → Li₂O + Li–Zn + Fe) and their structural reversibility are recognized by X-ray diffraction and electrochemical characterization. The products of the deeply discharged (Li–Zn alloy and Fe) and recharged materials (Fe₂O₃) were clarified based on high resolution transmission electron microscopic technique and first-principle calculations.     

Study on the effect of Li doping in spinel Li4+xTi5−xO12 (0 ⩽ x ⩽ 0.2) materials for lithium-ion batteries

The effect of Li doping in spinel Li_4+xTi_5−xO₁₂ (0 ⩽ x ⩽ 0.2) materials on the structural and electrochemical properties were investigated. The ratio of the capacity in the voltage plateau (1.5 V) to the overall discharge capacity for Li_4.1Ti_4.9O₁₂ (x = 0.1) and Li_4.2Ti_4.8O₁₂ (x = 0.2) were higher than that of Li₄Ti₅O₁₂ especially at high current rates due to their enhanced lithium-ion and electronic conductivity by the substitution of Ti atoms by Li atoms. With the increasing of Li doping amount, lithium-ion and electronic conductivity of Li_4+xTi_5−xO₁₂ increased, however its cycling stability was depressed when the Li doping was of x = 0.2. The Li doping of x = 0.1, the appropriate Li doping amount, showed improved rate capability and better high rate performance comparing to undoped Li_4+xTi_5−xO₁₂ (x = 0).     

High-energy and high-power Li-rich nickel manganese oxide electrode materials

A lithium-rich nickel-manganese oxide compound Li_x(Ni_0.25Mn_0.75)O_y (x > 1) was synthesized from layered Na_0.9Li_0.3Ni_0.25Mn_0.75O_δ precursor using a lithium ion-exchange reaction. The electrochemical behavior of the material as a cathode for lithium batteries, and a preliminary discussion of its structure are reported. The product Li_1.32Na_0.02Ni_0.25Mn_0.75O_y (IE-LNMO) shows broad X-ray diffraction peaks, but possesses a high intensity sharp (003) layering peak and multiple peaks with intensity in the 20–23° 2θ region which suggest Ni–Mn ordering in the transition metal layer (TM). Li/IE-LNMO cells demonstrate very stable reversible capacities of 220 mAh/g @ 15 mA/g and possess extremely high power of 150 mAh/g @ 1500 mA/g (15C). The Li/IE-LNMO cell dQ/dV plot exhibits three reversible electrochemical processes due to Ni/Mn redox behavior in a layered component, and Mn redox exchange in a spinel component. No alteration in the dQ/dV curves and no detectable change in the voltage profiles over 40 cycles were observed, thus indicating a stable structure for lithium insertion/extraction. This new material is attractive for demanding Li-ion battery applications.     

High capacity Li[Li0.2Mn0.54Ni0.13Co0.13]O2–V2O5 composite cathodes with low irreversible capacity loss for lithium ion batteries

With an aim to suppress the huge irreversible capacity loss encountered in high capacity layered oxide solid solutions between Li₂MnO₃ and LiMO₂ (M = Mn, Ni, and Co), layered Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂–V₂O₅ composite cathodes with various V₂O₅ contents have been investigated. The irreversible capacity loss decreases from 68 mAh/g at 100% Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ to 0 mAh/g around 89 wt.% Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂–11 wt.% V₂O₅ as the lithium-free V₂O₅ serves as an insertion host to accommodate the lithium ions that could not be inserted back into the layered lattice after the first charge. The Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂–V₂O₅ composite cathodes with about 10–12 wt.% V₂O₅ exhibit an attractive discharge capacity of close to 300 mAh/g with little irreversible capacity loss and good cyclability.     

Tunable lithium storage properties of metal lithium titanates by stoichiometric modulation

A simple stoichiometric modulation of Na_2 − 2xSr_xLi₂Ti₆O₁₄ was developed to achieve tunable electrochemical properties of the material. The concept was confirmed experimentally and theoretically using density functional theory (DFT) calculations. Both the operating potential and the amount of reversibly intercalated lithium ions were manipulated by simply changing the Na/Sr ratio. These unique characteristics originated from a gradual change in the electron density on the Ti atoms and the extra lithium insertion sites at SrLi₂Ti₆O₁₄. As a promising anode material for lithium-ion batteries, Na_2 − 2xSr_xLi₂Ti₆O₁₄ and its tunable electrochemical properties have significant importance in terms of the development of tailored electrodes with desirable electrochemical performance.     

Lithium–manganese–nickel-oxide electrodes with integrated layered–spinel structures for lithium batteries

A series of lithium–manganese–nickel-oxide compositions that can be represented in three-component notation, xLi[Mn_1.5Ni_0.5]O₄ · (1 − x){Li₂MnO₃ · Li(Mn_0.5Ni_0.5)O₂}, in which a spinel component, Li[Mn_1.5Ni_0.5]O₄, and two layered components, Li₂MnO₃ and Li(Mn_0.5Ni_0.5)O₂, are structurally integrated in a highly complex manner, have been evaluated as electrodes in lithium cells for x = 1, 0.75, 0.50, 0.25 and 0. In this series of compounds, which is defined by the Li[Mn_1.5Ni_0.5]O₄–{Li₂MnO₃ · Li(Mn_0.5Ni_0.5)O₂} tie-line in the Li[Mn_1.5Ni_0.5]O₄–Li₂MnO₃–Li(Mn_0.5Ni_0.5)O₂ phase diagram, the Mn:Ni ratio in the spinel and the combined layered Li₂MnO₃ · Li(Mn_0.5Ni_0.5)O₂ components is always 3:1. Powder X-ray diffraction patterns of the end members and the electrochemical profiles of cells with these electrodes are consistent with those expected for the spinel Li[Mn_1.5Ni_0.5]O₄ (x = 1) and for ‘composite’ Li₂MnO₃ · Li(Mn_0.5Ni_0.5)O₂ layered electrode structures (x = 0). Electrodes with intermediate values of x exhibit both spinel and layered character and yield extremely high capacities, reaching more than 250 mA h/g with good cycling stability between 2.0 V and 4.95 V vs. Li° at a current rate of 0.1 mA/cm².     

Comments on stabilizing layered manganese oxide electrodes for Li batteries

An electrochemical study of structurally-integrated xLi₂MnO₃•(1 −x)LiMn_0.5Ni_0.5O₂ ‘composite’ materials has been undertaken to investigate the stability of electrochemically-activated electrodes at the Li₂MnO₃-rich end of the Li₂MnO₃–LiMn_0.5Ni_0.5O₂ tie-line, i.e., for 0.7 ≤ x ≤ 0.95. Excellent performance was observed for x = 0.7 in lithium half-cells; comparable to activated electrodes that have significantly lower values of x and are traditionally the preferred materials of choice. Electrodes with higher manganese content (x ≥ 0.8) showed significantly reduced performance. Implications for stabilizing low-cost, manganese-rich, layered lithium-metal-oxide electrode materials are discussed.     

Electrospun nano-vanadium pentoxide cathode

Nanocrystallites of vanadium pentoxide were synthesized by the hydrothermal treatment of electrospun composite nanofibers. Each crystallite of dimension ?100 nm was found to be a single crystal of δ-phase H_xV₄O₁₀ · nH₂O. The crystallinity and morphology was maintained on heating to 500 °C when V₂O₅ was formed. The electrochemical capacity of the nano-V₂O₅ in a lithium cell was found to be above 350 mAh/g. The columbic efficiency is close to 100% when small amounts of lithium bis(oxalato)borate is added to the LiPF₆ electrolyte.     

Electrochemical properties of Li(Li(1−x)/3CoxMn(2−2x)/3)O2 (0 ⩽ x ⩽ 1) solid solutions prepared by poly-vinyl alcohol (PVA) method

The whole range of solid solutions Li(Li_(1−x)/3Co_xMn_(2−2x)/3)O₂ (0 ⩽ x ⩽ 1) was firstly synthesized by an aqueous solution method using poly-vinyl alcohol as a synthetic agent to investigate their structure and electrochemical properties. X-ray diffraction results indicated that the synthesized solid solutions showed a single phase without any detectable impurity phase and have a hexagonal structure with some additional peaks caused by monoclinic distortion, especially in the solid solutions with a low Co amount. In the electrochemical examination, the solid solutions in the range between 0.2 ⩽ x ⩽ 0.9 showed higher discharge capacity and better cyclability than LiCoO₂ (x = 1) on cycling between 2.0 and 4.6 V with 100 mA g⁻¹ at 25 °C. For example, Li(Li_0.2Co_0.4Mn_0.4)O₂ (x = 0.4) exhibited a high discharge capacity of 180 mA h g⁻¹ at the 50th cycle. By synthesizing the solid solution between Li₂MnO₃ and LiCoO₂, the electrochemical properties of the end members were improved.     

Enhancing the rate capability of high capacity xLi2MnO3 · (1 − x)LiMO2 (M = Mn,Ni, Co) electrodes by Li–Ni–PO4 treatment

The rate capability of high capacity xLi₂MnO₃ · (1 ? x)LiMO₂ (M = Mn, Ni, Co) electrodes for lithium-ion batteries has been significantly enhanced by stabilizing the electrode surface by reaction with a Li–Ni–PO₄ solution, followed by a heat-treatment step. Reversible capacities of 250 mAh/g at a C/11 rate, 225 mAh/g at C/2 and 200 mAh/g at C/1 have been obtained from 0.5Li₂MnO₃ · 0.5LiNi_0.44Co_0.25Mn_0.31O₂ electrodes between 4.6 and 2.0 V. The data bode well for their implementation in batteries that meet the 40-mile range requirement for plug-in hybrid vehicles.     

Li(4−x)/3Ti(5−2x)/3CrxO4 (0 ≤ x ≤ 0.9) spinels: New negatives for lithium batteries

Members of the spinel solid solution between Li_4/3Ti_5/3O₄ and LiCrTiO₄, i.e., Li_(4−x)/3Ti_(5−2x)/3Cr_xO₄ (0 ≤ x ≤ 0.9), have been investigated as possible negative electrodes for future lithium-ion batteries. Electrochemical behaviour have been studied over the potential range 1–3.5 V vs Li⁺/Li. Results are promising with anodic capacities between 129 and 163 mA h/g with a flat operating voltage at about 1.5 V, which is attributed to the pair Ti⁴⁺/Ti³⁺. The inclusion of Cr³⁺ in the spinel structure enhances the specific capacity. In-situ X-ray diffraction experiments confirm that the reaction proceeds in a topotactic manner.     

Li2CuTi3O8–Li4Ti5O12 double spinel anode material with improved rate performance for Li-ion batteries

Ti-based anode materials with the nominal compositions Li₄Ti₅Cu_xO_12 + x (x = 0, 0.075, 0.15, 0.3, 0.6, 1.20 and 1.67) were synthesized at 800 °C by a solid-state reaction process. X-ray diffraction analysis indicated that the sintered samples were composed of intergrown spinel-type Li₄Ti₅O₁₂ and Li₂CuTi₃O₈, and a small amount of Li₂O. Scanning electron microscopy, electrical resistance measurement and galvanostatic cell cycling were also employed to characterize the structure and properties of the double spinel samples. It is proposed that the first lithiation of the component Li₂CuTi₃O₈ leads to the in situ production of Cu that can significantly improve the rate performance of Li₄Ti₅Cu_xO_12 + x. The optimal nominal composition is Li₄Ti₅Cu_0.15O_12.15.     

Impedance study on the correlation between phase transition and electrochemical degradation of Si-based materials

In order to explain the relationship between physical change and electrochemical degradation of Co–Co₃O₄ coated Si, impedance spectroscopy on Co–Co₃O₄ coated Si was conducted at various states during charge or discharge. Nyquist plots during Li⁺ insertion (charge) showed a unique behavior that below 70 mV vs. Li/Li⁺, the more Li⁺’s were inserted into the electrode, the larger its comprehensive resistance was getting. During Li⁺ extraction (discharge), electrode resistance was decreased after going through 0.43 V vs Li/Li⁺. When these data were fitted with the ordinary equivalent circuit which is composed of electrolyte resistance, charge transfer resistance and contact resistance, there was an abrupt augmentation of charge transfer resistance below 70 mV vs. Li/Li⁺ during charge, whereas there was its drastic diminishment between 0.2 and 0.5 V vs. Li/Li⁺ during discharge. Because these potential regions are each related to amorphous Li_xSi-to-Li₁₅Si₄ transition and vice versa, it could be shown that the formation and decomposition of Li₁₅Si₄ is responsible for the electrochemical degradation of Co–Co₃O₄ coated Si.     

A strategy for scalable synthesis of Li4Ti5O12/reduced graphene oxide toward high rate lithium-ion batteries

Li₄Ti₅O₁₂/reduced graphene oxide (RGO) composites were prepared via a simple strategy. The as-prepared composites present Li₄Ti₅O₁₂ nanoparticles uniformly immobilized on the RGO sheets. The Li₄Ti₅O₁₂/RGO composites possess excellent electrochemical properties with good cycle stability and high specific capacities of 154 mAh g^− 1 (at 10C) and 149 mAh g^− 1 (at 20C), much higher than the results found in other literatures. The superior electrochemical performance of the Li₄Ti₅O₁₂/RGO composites is attributed to its unique hybrid structure of conductive graphene network with the uniformly dispersed Li₄Ti₅O₁₂ nanoparticles.     

Kinetics and mechanism of the chromic oxidation of 3-O-methyl-d-glucopyranose

The oxidation of 3-O-methyl-d-glucopyranose (Glc3Me) by Cr^VI in acid medium yields Cr^III, formic acid and 2-O-methyl-d-arabinose as final products when a 50-times or higher excess of Glc3Me over Cr^VI is used. The redox reaction takes place through the combination of Cr^VI → Cr^IV → Cr^II and Cr^VI → Cr^IV → Cr^III pathways. Intermediacy of free radicals and Cr^II in the reaction was demonstrated by the observation of induced polymerization of acrylamide and detection of CrO₂²⁺ formed by reaction of Cr^II with O₂. Intermediate oxo-Cr^V–Glc3Me species were detected by EPR spectroscopy. In 0.3–0.5 mol/L HClO₄, intermediate Cr^V rapidly decompose to the reaction products, while, at pH 5.5–7.5, where the redox processes are very slow, five-coordinate Cr^V bis-chelates of the pyranose and furanose forms of Glc3Me remain more than 15 h in solution. The C1–C2 bond cleavage of Glc3Me upon reaction with Cr^VI distinguishes this derivative from glucose, which is oxidized to gluconic acid.     

Comparison of the electrochemical properties of metallic layered nitrides containing cobalt,nickel and copper in the 1 V–0.02 V potential range

We report the first example of an intercalation compound based on the nitrogen framework in which lithium can be intercalated and deintercalated. A comparison of the structural and electrochemical properties of the ternary lithium cobalt, nickel and copper nitrides is performed. Vacancy layered structures of ternary lithium nitridocobaltates Li_3−2xCo_xN and nitridonickelates Li_3−2xNi_xN with 0.10 ⩽ x ⩽ 0.44 and 0.20 ⩽ x ⩽ 0.60, respectively, are proved to reversibly intercalate Li ions in the 1 V–0.02 V potential range. These host lattices can accommodate up to 0.35 Li ion par mole of nitride. Results herein obtained support Li insertion in vacancies located in Li₂N⁻ layers while interlayer divalent cobalt and nickel cations are reduced to monovalent species. No structural strain is induced by the insertion–extraction electrochemical reaction which explains the high stability of the capacity in both cases. For the Li_1.86Ni_0.57N compound, a stable faradaic yield of 0.30 F/mol, i.e. 130 mAh/g, is maintained at least for 100 cycles. Conversely, the ternary copper nitrides corresponding to the chemical composition Li_3−xCu_xN with 0.10 ⩽ x ⩽ 0.40 do not allow the insertion reaction to take place due to the presence of monovalent copper combined with the lack of vacancies to accommodate Li ions. In the latter case, the discharge of the lithium copper nitrides is not reversible.     

Photo-luminescence studies of strontium barium niobate crystals doped with Cr3+ ions

This paper reports the photo-luminescence spectroscopic results of Strontium–Barium–Niobate, Sr_x,Ba_1−xNb₂O₅ (SBN, x = 0.61 for near congruent composition) crystals doped with Cr₂O, at cryogenic temperature (20 K). The experimental results reveal the need of re-assignment of the Cr³⁺ ions defect centres in this material. For first time, a broad emission band in the near infrared region centred at ca. 950 nm is reported. This emission band has micro-seconds decaytime constant and a FWHM band-width > 1700 cm⁻¹ and has been ascribed to the vibronically assisted ⁴T₂ → ⁴A₂ transition. A much narrower emission band centred at ca. 764 nm with milli-seconds decaytime constant and a FWHM band-width of ca. 170 cm⁻¹ is correlated to the ²E → ⁴A₂ radiative transition (R-line).     

Anomalous capacity and cycling stability of xLi2MnO3 · (1 − x)LiMO2 electrodes (M = Mn,Ni, Co) in lithium batteries at 50 °C

Transition metal oxides with composite xLi₂MnO₃ ·  (1 − x)LiMO₂ rocksalt structures (M = Mn, Ni, Co) are of interest as a new generation of cathode materials for high energy density lithium-ion batteries. After electrochemical activation to 4.6 or 4.8 V (vs. Li⁰) at 50 °C, xLi₂MnO₃ · (1 − x)LiMn_0.33Ni_0.33Co_0.33O₂ (x = 0.5, 0.7) electrodes deliver initial discharge capacities (>300 mAh/g) at a low current rate (0.05 mA/cm²) that exceed the theoretical values for lithiation back to the rocksalt stoichiometry (240–260 mAh/g), at least during the early charge/discharge cycles of the cells. Attention is drawn to previous reports of similar, but unaccounted and unexplained anomalous behavior of these types of electrode materials. Possible reasons for this anomalous capacity are suggested. Indications are that electrodes in which M = Mn, Ni and Co do not cycle with the same stability at 50 °C as those without cobalt.     

Phase equilibria in ternary (carbon dioxide + tetrahydrofuran + water) system in hydrate-forming region: Effects of carbon dioxide concentration and the occurrence of pseudo-retrograde hydrate phenomenon

In the present work, the three- and four-phase hydrate equilibria of (carbon dioxide (CO₂) + tetrahydrofuran (THF) + water) system are measured by using Cailletet equipment in the temperature and pressure range of (272 to 292) K and (1.0 to 7.5) MPa, respectively, at different CO₂ concentration. Throughout the study, the concentration of THF is kept constant at 5 mol% in the aqueous solution. In addition, the fluid phase transitions of L_W–L_V–V → L_W–L_V (bubble point) and L_W–L_V–V → L_W–V (dew point) are determined when they are present in the ternary system. For comparison, the three-phase hydrate equilibria of binary (CO₂ + H₂O) are also measured. Experimental measurements show that the addition of THF as a hydrate promoter extends hydrate stability region by elevating the hydrate equilibrium temperature at a specified pressure. The three-phase equilibrium line H–L_W–V is found to be independent of the overall concentration of CO₂. Contradictory, at higher pressure, the phase equilibria of the systems are significantly influenced by the overall concentration of CO₂ in the systems. A liquid–liquid phase split is observed at overall concentration of CO₂ as low as 3 mol% at elevated pressure. The region is bounded by the bubble-points line (L_W–L_V–V → L_W–L_V), dew points line (L_W–L_V–V → L_W + V) and the four-phase equilibrium line (H + L_W + L_V + V). At higher overall concentration of CO₂ in the ternary system, experimental measurements show that pseudo-retrograde behaviour exists at pressure between (2.5 and 5) MPa at temperature of 290.8 K.