Highly Porous Carbons Synthesized from Tannic Acid via a Combined Mechanochemical Salt-Templating and Mild Activation Strategy

Highly porous activated carbons were synthesized via the mechanochemical salt-templating method using both sustainable precursors and sustainable chemical activators. Tannic acid is a polyphenolic compound derived from biomass, which, together with urea, can serve as a low-cost, environmentally friendly precursor for the preparation of efficient N-doped carbons. The use of various organic and inorganic salts as activating agents afforded carbons with diverse structural and physicochemical characteristics, e.g., their specific surface areas ranged from 1190 m²·g⁻¹ to 3060 m²·g⁻¹. Coupling the salt-templating method and chemical activation with potassium oxalate appeared to be an efficient strategy for the synthesis of a highly porous carbon with a specific surface area of 3060 m²·g⁻¹, a large total pore volume of 3.07 cm³·g⁻¹ and high H₂ and CO₂ adsorption capacities of 13.2 mmol·g⁻¹ at −196 °C and 4.7 mmol·g⁻¹ at 0 °C, respectively. The most microporous carbon from the series exhibited a CO₂ uptake capacity as high as 6.4 mmol·g⁻¹ at 1 bar and 0 °C. Moreover, these samples showed exceptionally high thermal stability. Such activated carbons obtained from readily available sustainable precursors and activators are attractive for several applications in adsorption and catalysis.     

The Use of High Surface Area Mesoporous-Activated Carbon from Longan Seed Biomass for Increasing Capacity and Kinetics of Methylene Blue Adsorption from Aqueous Solution

Microporous- and mesoporous-activated carbons were produced from longan seed biomass through physical activation with CO₂ under the same activation conditions of time and temperature. The specially prepared mesoporous carbon showed the maximum porous properties with the specific surface area of 1773 m²/g and mesopore volume of 0.474 cm³/g which accounts for 44.1% of the total pore volume. These activated carbons were utilized as porous adsorbents for the removal of methylene blue (MB) from an aqueous solution and their effectiveness was evaluated for both the adsorption kinetics and capacity. The adsorption kinetic data of MB were analyzed by the pseudo-first-order model, the pseudo-second-order model, and the pore-diffusion model equations. It was found that the adsorption kinetic behavior for all carbons tested was best described by the pseudo-second-order model. The effective pore diffusivity (D_e) derived from the pore-diffusion model had the values of 4.657 × 10⁻⁷–6.014 × 10⁻⁷ cm²/s and 4.668 × 10⁻⁷–19.920 × 10⁻⁷ cm²/s for the microporous- and mesoporous-activated carbons, respectively. Three well-known adsorption models, namely the Langmuir, Freundlich and Redlich–Peterson equations were tested with the experimental MB adsorption isotherms, and the results showed that the Redlich–Peterson model provided the overall best fitting of the isotherm data. In addition, the maximum capacity for MB adsorption of 1000 mg/g was achieved with the mesoporous carbon having the largest surface area and pore volume. The initial pH of MB solution had virtually no effect on the adsorption capacity and removal efficiency of the methylene blue dye. Increasing temperature over the range from 35 to 55 °C increased the adsorption of methylene blue, presumably caused by the increase in the diffusion rate of methylene blue to the adsorption sites that could promote the interaction frequency between the adsorbent surface and the adsorbate molecules. Overall, the high surface area mesoporous carbon was superior to the microporous carbon in view of the adsorption kinetics and capacity, when both carbons were used for the removal of MB from an aqueous solution.     

HTO/Cellulose Aerogel for Rapid and Highly Selective Li+ Recovery from Seawater

To achieve rapid and highly efficient recovery of Li⁺ from seawater, a series of H₂TiO₃/cellulose aerogels (HTO/CA) with a porous network were prepared by a simple and effective method. The as-prepared HTO/CA were characterized and their Li⁺ adsorption performance was evaluated. The obtained results revealed that the maximum capacity of HTO/CA to adsorb Li⁺ was 28.58 ± 0.71 mg g⁻¹. The dynamic k₂ value indicated that the Li⁺ adsorption rate of HTO/CA was nearly five times that of HTO powder. Furthermore, the aerogel retained extremely high Li⁺ selectivity compared with Mg²⁺, Ca²⁺, K⁺, and Na⁺. After regeneration for five cycles, the HTO/CA retained a Li⁺ adsorption capacity of 22.95 mg g⁻¹. Moreover, the HTO/CA showed an excellent adsorption efficiency of 69.93% ± 0.04% and high selectivity to Li⁺ in actual seawater. These findings confirm its potential as an adsorbent for recovering Li⁺ from seawater.     

MWCNT Decorated Rich N-Doped Porous Carbon with Tunable Porosity for CO2 Capture

Designing of porous carbon system for CO₂ uptake has attracted a plenty of interest due to the ever-increasing concerns about climate change and global warming. Herein, a novel N rich porous carbon is prepared by in-situ chemical oxidation polyaniline (PANI) on a surface of multi-walled carbon nanotubes (MWCNTs), and then activated with KOH. The porosity of such carbon materials can be tuned by rational introduction of MWCNTs, adjusting the amount of KOH, and controlling the pyrolysis temperature. The obtained M/P-0.1-600-2 adsorbent possesses a high surface area of 1017 m² g⁻¹ and a high N content of 3.11 at%. Such M/P-0.1-600-2 adsorbent delivers an enhanced CO₂ capture capability of 2.63 mmol g⁻¹ at 298.15 K and five bars, which is 14 times higher than that of pristine MWCNTs (0.18 mmol g⁻¹). In addition, such M/P-0.1-600-2 adsorbent performs with a good stability, with almost no decay in a successive five adsorption-desorption cycles.     

Preparation of Bamboo-Based Hierarchical Porous Carbon Modulated by FeCl3 towards Efficient Copper Adsorption

Using bamboo powder biochar as raw material, high-quality meso/microporous controlled hierarchical porous carbon was prepared—through the catalysis of Fe³⁺ ions loading, in addition to a chemical activation method—and then used to adsorb copper ions in an aqueous solution. The preparation process mainly included two steps: load-alkali leaching and chemical activation. The porosity characteristics (specific surface area and mesopore ratio) were controlled by changing the K₂CO₃ impregnation ratio, activation temperature, and Fe³⁺ ions loading during the activation process. Additionally, three FBPC samples with different pore structures and characteristics were studied for copper adsorption. The results indicate that the adsorption performance of the bamboo powder biochar FBPC material was greatly affected by the meso/micropore ratio. FBPC _2.5-900-2%, impregnated at a K₂CO₃: biochar ratio of 2.5 and a Fe³⁺: biochar mass ratio of 2%, and activated at 900 °C for 2 h in N₂ atmosphere, has a very high specific surface area of 1996 m² g⁻¹ with a 58.1% mesoporous ratio. Moreover, it exhibits an excellent adsorption capacity of 256 mg g⁻¹ and rapid adsorption kinetics for copper ions. The experimental results show that it is feasible to control the hierarchical pore structure of bamboo biochar-derived carbons as a high-performance adsorbent to remove copper ions from water.     

CoMnO2-Decorated Polyimide-Based Carbon Fiber Electrodes for Wire-Type Asymmetric Supercapacitor Applications

In this work, we report the carbon fiber-based wire-type asymmetric supercapacitors (ASCs). The highly conductive carbon fibers were prepared by the carbonized and graphitized process using the polyimide (PI) as a carbon fiber precursor. To assemble the ASC device, the CoMnO₂-coated and Fe₂O₃-coated carbon fibers were used as the cathode and the anode materials, respectively. Herein, the nanostructured CoMnO₂ were directly deposited onto carbon fibers by a chemical oxidation route without high temperature treatment in presence of ammonium persulfate (APS) as an oxidizing agent. FE-SEM analysis confirmed that the CoMnO₂-coated carbon fiber electrode exhibited the porous hierarchical interconnected nanosheet structures, depending on the added amount of APS, and Fe₂O₃-coated carbon fiber electrode showed a uniform distribution of porous Fe₂O₃ nanorods over the surface of carbon fibers. The electrochemical properties of the CoMnO₂-coated carbon fiber with the concentration of 6 mmol APS presented the enhanced electrochemical activity, probably due to its porous morphologies and good conductivity. Further, to reduce the interfacial contact resistance as well as improve the adhesion between transition metal nanostructures and carbon fibers, the carbon fibers were pre-coated with the Ni layer as a seed layer using an electrochemical deposition method. The fabricated ASC device delivered a specific capacitance of 221 F g⁻¹ at 0.7 A g⁻¹ and good rate capability of 34.8% at 4.9 A g⁻¹. Moreover, the wire-type device displayed the superior energy density of 60.2 Wh kg⁻¹ at a power density of 490 W kg⁻¹ and excellent capacitance retention of 95% up to 3000 charge/discharge cycles.     

Zirconium-Based Metal Organic Frameworks for the Capture of Carbon Dioxide and Ethanol Vapour. A Comparative Study

This paper reports on the comparison of three zirconium-based metal organic frameworks (MOFs) for the capture of carbon dioxide and ethanol vapour at ambient conditions. In terms of efficiency, two parameters were evaluated by experimental and modeling means, namely the nature of the ligands and the size of the cavities. We demonstrated that amongst three Zr-based MOFs, MIP-202 has the highest affinity for CO₂ (−50 kJ·mol⁻¹ at low coverage against around −20 kJ·mol⁻¹ for MOF-801 and Muc Zr MOF), which could be related to the presence of amino functions borne by its aspartic acid ligands as well as the presence of extra-framework anions. On the other side, regardless of the ligand size, these three materials were able to adsorb similar amounts of carbon dioxide at 1 atm (between 2 and 2.5 µmol·m⁻² at 298 K). These experimental findings were consistent with modeling studies, despite chemisorption effects, which could not be taken into consideration by classical Monte Carlo simulations. Ethanol adsorption confirmed these results, higher enthalpies being found at low coverage for the three materials because of stronger van der Waals interactions. Two distinct sorption processes were proposed in the case of MIP-202 to explain the shape of the enthalpic profiles.     

Preparation of High-Performance Activated Carbon from Coffee Grounds after Extraction of Bio-Oil

In this study, a new method for economical utilization of coffee grounds was developed and tested. The resulting materials were characterized by proximate and elemental analyses, thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and N₂ adsorption–desorption at 77 K. The experimental data show bio-oil yields reaching 42.3%. The optimal activated carbon was obtained under vacuum pyrolysis self-activation at an operating temperature of 450 °C, an activation temperature of 600 °C, an activation time of 30 min, and an impregnation ratio with phosphoric acid of 150 wt.%. Under these conditions, the yield of activated carbon reached 27.4% with a BET surface area of 1420 m²·g⁻¹, an average pore size of 2.1 nm, a total pore volume of 0.747 cm³·g⁻¹, and a t-Plot micropore volume of 0.428 cm³·g⁻¹. In addition, the surface of activated carbon looked relatively rough, containing mesopores and micropores with large amounts of corrosion pits.     

Lithium silicate nanosheets with excellent capture capacity and kinetics with unprecedented stability for high-temperature CO2 capture

An excessive amount of CO₂ is the leading cause of climate change, and hence, its reduction in the Earth''s atmosphere is critical to stop further degradation of the environment. Although a large body of work has been carried out for post-combustion low-temperature CO₂ capture, there are very few high temperature pre-combustion CO₂ capture processes. Lithium silicate (Li₄SiO₄), one of the best known high-temperature CO₂ capture sorbents, has two main challenges, moderate capture kinetics and poor sorbent stability. In this work, we have designed and synthesized lithium silicate nanosheets (LSNs), which showed high CO₂ capture capacity (35.3 wt% CO₂ capture using 60% CO₂ feed gas, close to the theoretical value) with ultra-fast kinetics and enhanced stability at 650 °C. Due to the nanosheet morphology of the LSNs, they provided a good external surface for CO₂ adsorption at every Li-site, yielding excellent CO₂ capture capacity. The nanosheet morphology of the LSNs allowed efficient CO₂ diffusion to ensure reaction with the entire sheet as well as providing extremely fast CO₂ capture kinetics (0.22 g g⁻¹ min⁻¹). Conventional lithium silicates are known to rapidly lose their capture capacity and kinetics within the first few cycles due to thick carbonate shell formation and also due to the sintering of sorbent particles; however, the LSNs were stable for at least 200 cycles without any loss in their capture capacity or kinetics. The LSNs neither formed a carbonate shell nor underwent sintering, allowing efficient adsorption–desorption cycling. We also proposed a new mechanism, a mixed-phase model, to explain the unique CO₂ capture behavior of the LSNs, using detailed (i) kinetics experiments for both adsorption and desorption steps, (ii) in situ diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy measurements, (iii) depth-profiling X-ray photoelectron spectroscopy (XPS) of the sorbent after CO₂ capture and (iv) theoretical investigation through systematic electronic structure calculations within the framework of density functional theory (DFT) formalism.

Capturing CO₂ before its release. Lithium silicate nanosheets showed high CO₂ capture capacity (35.3 wt%) with ultra-fast kinetics (0.22 g g⁻¹ min⁻¹) and enhanced stability at 650 °C for at least 200 cycles, due to mixed-phase-model of CO₂ capture.     

Adsorption separation of carbon dioxide, methane and nitrogen on monoethanol amine modified B-zeolite

A new type of composite adsorbents was synthesized by incorporating monoethanol amine (MEA) into β-zeolite. The parent and MEA-functionalized β-zeolites were characterized by X-ray diffraction (XRD), N₂ adsorption, and thermogravimetric analysis (TGA). The adsorption behavior of carbon dioxide (CO₂), methane (CH₄), and nitrogen (N₂) on these adsorbents was investigated at 303 K. The results show that the structure of zeolite was well preserved after MEA modification. In comparison with CH₄ and N₂, CO₂ was preferentially adsorbed on the adsorbents investigated. The introduction of MEA significantly improved the selectivity of both CO₂/CH₄ and CO₂/N₂, the optimal selectivity of CO₂/CH₄ can reach 7.70 on 40 wt% of MEA-functionalized β-zeolite (MEA(40)-β) at 1 atm. It is worth noticing that a very high selectivity of CO₂/N₂ of 25.67 was obtained on MEA(40)-β. Steric effect and chemical adsorbate-adsorbent interaction were responsible for such high adsorption selectivity of CO₂. The present MEA-functionalized β-zeolite adsorbents may be a good candidate for applications in flue gas separation, as well as natural gas and landfill gas purifications.     

PAN-based activated carbon nanofiber/metal oxide composites for CO2 and CH4 adsorption: influence of metal oxide

In the present study, we successfully prepared two different electrospun polyacrylonitrile (PAN) based-activated carbon nanofiber (ACNF) composites by incorporation of well-distributed Fe₂O₃ and Co₃O₄ nanoparticles (NPs). The influence of metal oxide on the structural, morphological, and textural properties of final composites was thoroughly investigated. The results showed that the morphological and textural properties could be easily tuned by changing the metal oxide NPs. Even though, the ACNF composites were not chemically activated by any activation agent, they presented relatively high surface areas (S_BET) calculated by Brunauer–Emmett–Teller (BET) equation as 212.21 and 185.12 m²/g for ACNF/Fe₂O₃ and ACNF/Co₃O₄ composites, respectively. Furthermore, the ACNF composites were utilized as candidate adsorbents for CO₂ and CH₄ adsorption. The ACNF/Fe₂O₃ and ACNF/Co₃O₄ composites resulted the highest CO₂ adsorption capacities of 1.502 and 2.166 mmol/g at 0 °C, respectively, whereas the highest CH₄ adsorption capacities were obtained to be 0.516 and 0.661 mmol/g at 0 °C by ACNF/Fe₂O₃ and ACNF/Co₃O₄ composites, respectively. The isosteric heats calculated lower than 80 kJ/mol showed that the adsorption processes of CO₂ and CH₄ were mainly dominated by physical adsorption for both ACNF composites. Our findings indicated that ACNF-metal oxide composites are useful materials for designing of CO₂ and CH₄ adsorption systems.     

Greener Monolithic Solid Phase Extraction Biosorbent Based on Calcium Cross-Linked Starch Cryogel Composite Graphene Oxide Nanoparticles for Benzo(a)pyrene Analysis

Benzo(a)pyrene (BaP) has been recognized as a marker for the detection of carcinogenic polycyclic aromatic hydrocarbons. In this work, a novel monolithic solid-phase extraction (SPE) sorbent based on graphene oxide nanoparticles (GO) in starch-based cryogel composite (GO-Cry) was successfully prepared for BaP analysis. Rice flour and tapioca starch (gel precursors) were gelatinized in limewater (cross-linker) under alkaline conditions before addition of GO (filler) that can increase the ability to extract BaP up to 2.6-fold. BaP analysis had a linear range of 10 to 1000 µgL⁻¹ with good linearity (R² = 0.9971) and high sensitivity (4.1 ± 0.1 a.u./(µgL⁻¹)). The limit of detection and limit of quantification were 4.21 ± 0.06 and 14.04 ± 0.19 µgL⁻¹, respectively, with excellent precision (0.17 to 2.45%RSD). The accuracy in terms of recovery from spiked samples was in the range of 84 to 110% with no significant difference to a C₁₈ cartridge. GO-Cry can be reproducibly prepared with 2.8%RSD from 4 lots and can be reused at least 10 times, which not only helps reduce the analysis costs (~0.41USD per analysis), but also reduces the resultant waste to the environment.     

Adsorption separation of carbon dioxide,methane, and nitrogen on Hβ and Na-exchanged β-zeolite

Adsorption isotherms of carbon dioxide （CO2）, methane （CH4）, and nitrogen （N2） on Hβand sodium exchanged β-zeolite （Naβ） were volumetrically measured at 273 and 303 K. The results show that all isotherms were of Brunauer type I and well correlated with Langmuir-Freundlich model. After sodium ions exchange, the adsorption amounts of three adsorbates increased, while the increase magnitude of CO2 adsorption capacity was much higher than that of CH4 and N2. The selectivities of CO2 over CH4 and CO2 over N2 enhanced after sodium exchange. Also, the initial heat of adsorption data implied a stronger interaction of CO2 molecules with Na＋ ions in Naβ . These results can be attributed to the larger electrostatic interaction of CO2 with extraframework cations in zeolites. However, Naβ showed a decrease in the selectivity of CH4 over N2, which can be ascribed to the moderate affinity of N2 with Naβ. The variation of isosteric heats of adsorption as a function of loading indicates that the adsorption of CO2 in Naβ presents an energetically heterogeneous profile. On the contrary, the adsorption of CH4 was found to be essentially homogeneous, which suggests the dispersion interaction between CH4 and lattice oxygen atoms, and such interaction does not depend on the exchangeable cations of zeolite.     

Cu2O-Ag Tandem Catalysts for Selective Electrochemical Reduction of CO2 to C2 Products

The electrochemical carbon dioxide reduction reaction (CO₂RR) to C₂ chemicals has received great attention. Here, we report the cuprous oxide (Cu₂O) nanocubes cooperated with silver (Ag) nanoparticles via the replacement reaction for a synergetic CO₂RR. The Cu₂O-Ag tandem catalyst exhibits an impressive Faradaic efficiency (FE) of 72.85% for C₂ products with a partial current density of 243.32 mA·cm⁻². The electrochemical experiments and density functional theory (DFT) calculations reveal that the introduction of Ag improves the intermediate CO concentration on the catalyst surface and meanwhile reduces the C-C coupling reaction barrier energy, which is favorable for the synthesis of C₂ products.     

Low Energy Electron Attachment by Some Chlorosilanes

In this paper, the rate coefficients (k) and activation energies (E_a) for SiCl₄, SiHCl₃, and Si(CH₃)₂(CH₂Cl)Cl molecules in the gas phase were measured using the pulsed Townsend technique. The experiment was performed in the temperature range of 298–378 K, and carbon dioxide was used as a buffer gas. The obtained k depended on temperature in accordance with the Arrhenius equation. From the fit to the experimental data points with function described by the Arrhenius equation, the activation energies (E_a) were determined. The obtained k values at 298 K are equal to (5.18 ± 0.22) × 10⁻¹⁰ cm³·s⁻¹, (3.98 ± 1.8) × 10⁻⁹ cm³·s⁻¹ and (8.46 ± 0.23) × 10⁻¹¹ cm³·s⁻¹ and E_a values were equal to 0.25 ± 0.01 eV, 0.20 ± 0.01 eV, and 0.27 ± 0.01 eV for SiHCl₃, SiCl₄, and Si(CH₃)₂(CH₂Cl)Cl, respectively. The linear relation between rate coefficients and activation energies for chlorosilanes was demonstrated. The DFT/B3LYP level coupled with the 6-31G(d) basis sets method was used for calculations of the geometry change associated with negative ion formation for simple chlorosilanes. The relationship between these changes and the polarizability of the attaching center (α_centre) was found. Additionally, the calculated adiabatic electron affinities (AEA) are related to the α_centre.     

Nano Carbon Doped Polyacrylamide Gel Electrolytes for High Performance Supercapacitors

Novel polyacrylamide gel electrolytes (PGEs) doped with nano carbons with enhanced electrochemical, thermal, and mechanical properties are presented. Carboxylated carbon nanotubes (fCNTs), graphene oxide sheets (GO), and the hybrid of fCNT/GO were embedded in the PGEs to serve as supercapacitor (SC) electrolytes. Thermal stability of the unmodified PGE increased with the addition of the nano carbons which led to lower capacitance degradation and longer cycling life of the SCs. The fCNT/GO-PGE showed the best thermal stability, which was 50% higher than original PGE. Viscoelastic properties of PGEs were also improved with the incorporation of GO and fCNT/GO. Oxygen-containing functional groups in GO and fCNT/GO hydrogen bonded with the polymer chains and improved the elasticity of PGEs. The fCNT-PGE demonstrated a slightly lower viscous strain uninform distribution of CNTs in the polymer matrix and the defects formed within. Furthermore, ion diffusion between GO layers was enhanced in fCNT/GO-PGE because fCNT decreased the aggregation of GO sheets and improved the ion channels, increasing the gel ionic conductivity from 41 to 132 mS cm⁻¹. Finally, MnO₂-based supercapacitors using PGE, fCNT-PGE, GO-PGE, and fCNT/GO-PGE electrolytes were fabricated with the electrode-specific capacitance measured to be 39.5, 65.5, 77.6, and 83.3 F·g⁻¹, respectively. This research demonstrates the effectiveness of nano carbons as dopants in polymer gel electrolytes for property enhancements.     

Synthesis of Fe2+ Substituted High-Performance LiMn1−xFexPO4/C (x = 0, 0.1, 0.2, 0.3, 0.4) Cathode Materials for Lithium-Ion Batteries via Sol-Gel Processes

A series of carbon-coated LiMn_1−xFe_xPO₄ (x = 0, 0.1, 0.2, 0.3, 0.4) materials are successfully constructed using glucose as carbon sources via sol-gel processes. The morphology of the synthesized material particles are more regular and particle sizes are more homogeneous. The carbon-coated LiMn_0.8Fe_0.2PO₄ material obtains the discharge specific capacity of 152.5 mAh·g⁻¹ at 0.1 C rate and its discharge specific capacity reaches 95.7 mAh·g⁻¹ at 5 C rate. Iron doping offers a viable way to improve the electronic conductivity and lattice defects of materials, as well as improving transmission kinetics, thereby improving the rate performance and cycle performance of materials, which is an effective method to promote the electrical properties.     

Voltammetric determination of itopride using carbon paste electrode modified with Gd doped TiO2 nanotubes

In the present work TiO₂ nanotubes (TNT) have been synthesized by alkaline hydrothermal transformation. Then they have been doped with Gd element. Characterizations of doped and undoped TNT have been done with TEM and SEM. The chemical composition was analyzed by EDX, Raman and FTIR spectroscopy. The crystal structure was characterized by XRD. Carbon paste electrode has been fabricated and mixed with Gd doped and undoped TNT to form a nanocomposite working electrode. Comparison of bare carbon paste electrode and Gd doped and undoped TNT carbon paste electrode for 1.0 ×10⁻³ M K₄ [Fe(CN)₆] voltammetric analysis; it was observed that Gd doped TNT modified electrode has advantage of high sensitivity. Gd doped TNT modified electrode has been used as working electrode for itopride assay in a pharmaceutical formulation. Cyclic voltammetry analysis showed high correlation coefficient of 0.9973 for itopride (0.04–0.2 mg/mL) with a limit of detection (LOD) and limit of quantitation values (LOQ) of 2.9 and 23.0 μg.mL⁻¹ respectively.     

Rational Construction of a Responsive Azo-Functionalized Porous Organic Framework for CO2 Sorption

An azo-functionalized porous organic framework (denoted as JJU-1) was synthesized via FeCl₃-promoted oxidative coupling polymerization. By virtue of a porous skeleton and a light/heat responsive azo functional group, this task-specific JJU-1 displays a reversible stimuli-responsive adsorption property triggered by UV irradiation and heat treatment. The initial Brunauer–Emmet–Teller (BET) surface area of this porous material is 467 m² g^–1. The CO₂ sorption isotherms exhibit a slight decrease after UV irradiation because of the trans to cis conversion of the azo functional skeleton. It is worth mentioning that the responsive CO₂ adsorption performance can be recycled for three cycles via alternating external stimuli, confirming the excellently reversible switchability of trans-to-cis isomerization and controllable CO₂ adsorption.     

A quasi-stable molybdenum sub-oxide with abundant oxygen vacancies that promotes CO2 hydrogenation to methanol

Production of methanol from anthropogenic carbon dioxide (CO₂) is a promising chemical process that can alleviate both the environmental burden and the dependence on fossil fuels. In catalytic CO₂ hydrogenation to methanol, reduction of CO₂ to intermediate species is generally considered to be a crucial step. It is of great significance to design and develop advanced heterogeneous catalysts and to engineer the surface structures to promote CO₂-to-methanol conversion. We herein report an oxygen-defective molybdenum sub-oxide coupled with Pt nanoparticles (Pt/H_xMoO_3−y) which affords high methanol yield with a methanol formation rate of 1.53 mmol g_-cat⁻¹ h⁻¹ in liquid-phase CO₂ hydrogenation under relatively mild reaction conditions (total 4.0 MPa, 200 °C), outperforming other oxide-supported Pt catalysts in terms of both the yield and selectivity for methanol. Experiments and comprehensive analyses including in situ X-ray absorption fine structure (XAFS), in situ diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy and density functional theory (DFT) calculations reveal that both abundant surface oxygen vacancies (V_O) and the redox ability of Mo species in quasi-stable H_xMoO_3−y confer the catalyst with enhanced adsorption and activation capability to subsequently transform CO₂ to methanol. Moreover, the Pt NPs act as H₂ dissociation sites to regenerate oxygen vacancies and as hydrogenation sites for the CO intermediate to finally afford methanol. Based on the experimental and computational studies, an oxygen-vacancy-mediated “reverse Mars–van Krevelen (M–vK)” mechanism is proposed. This study affords a new strategy for the design and development of an efficient heterogeneous catalyst for CO₂ conversion.

Oxygen-defective molybdenum sub-oxide coupled with Pt nanoparticles affords high methanol yield in liquid-phase CO₂ hydrogenation via reverse Mars–van Krevelen mechanism.