原油中有机硫化物成因的硫酸盐热化学还原反应模拟研究

原油中部分有机硫化物来源于硫酸盐热化学还原反应。利用高压釜在高温高压含水条件下对正戊烷 硫酸镁反应体系进行了热模拟实验研究。通过气相色谱仪、微库仑仪、毛细管气相色谱/脉冲火焰光度检测器、红外光谱仪及X射线衍射仪,对气、油、固三相产物进行了分析。结果表明,硫酸盐热化学还原反应在425℃~525℃可以进行,主要生成氧化镁、炭、硫化氢、二氧化碳以及硫醇、硫醚和噻吩类等有机硫化物。根据动力学模型计算出该反应活化能为58.0kJ/mol。     

炼焦收缩阶段半焦脱硫的实验研究

本文研究了半焦颗粒在炼焦收缩阶段脱硫的动力学行为,研究结果表明,半焦颗粒的脱硫与气体性质、流量有关.通过分析焦炭中各种形态的硫分,证实了在炼焦过程中存在着无机硫和一部分有机硫向噻吩硫转化.     

煤中有机硫形态结构和热解过程硫变迁特性的研究

利用热解 质谱并结合固定床热解反应装置，对煤中有机硫的形态主其对加氢热解过程 变迁特性的影响，进行了较系统的研究。结果表明，煤中有机硫的形态结构在褐煤中主要以脂肪族、芳香族硫化物为主，而在 煤中则主要以各种不同芳构化程度的噻吩结构为主，初步表明煤中有机硫形态结构随煤变质程度的变迁呈较强的连续递变性。煤热解过程中硫在呼产物中的变迁和分布与煤中有机硫的形态结构特点密切相关。较高芳构化噻吩结构不完全的氧     

煤的超临界醇萃取脱硫：Ⅲ.形态硫的变化

本文分别应用Ｍｏｓｓｂａｕｅｒ谱和ＸＰＳ（Ｘ射线光电子能谱）技术考察不同反应 条件下固体产物中的无机硫和有机硫的形态变化，结果表明；在超临界醇萃取脱硫过程中，黄铁矿硫的转化反应如下：ＦｅＳ２－ＦｅＳ＋Ｆｅ１－ｘＳ，，转化的数量和深度主要取决于反应温度。２７５℃时磁黄铁矿（Ｆｅ１－ｘＳ）形式为ＦｅＳ１．１０１，４５０℃时为ＦｅＳ１．０８５；有机硫基团中ＰｈＳＨ ，Ｐｈ２Ｓ和四氢噻吩较易脱除，Ｐｈ２Ｓ     

活性炭及甲酸催化过氧化氢氧化噻吩脱硫研究

以噻吩代表汽油中的有机硫化合物，将其溶解于正辛烷配制成反应原料，考察了活性炭对噻吩的吸附脱硫情况，研究了质量分数为30％的过氧化氢水溶液为氧化剂，在活性炭和甲酸的催化作用下，反应原料中噻吩氧化脱硫。考察了活性炭的催化性能及反应条件对其催化性能的影响。实验结果表明，30％H2O2-HCOOH-AC（活性炭）三元体系产生的过氧甲酸和羟基自由基能将模型有机硫化合物氧化，噻吩的氧化脱硫率可达到85％以上；活性炭和甲酸的催化氧化性能明显优于单纯使用甲酸催化性能。甲酸浓度、活性炭加入量、过氧化氢初始浓度及温度对噻吩硫的氧化脱除均有影响。     

高硫煤热解过程活性氢/氧对有机硫变迁行为影响研究述评

随着优质煤资源的消耗,高硫煤的清洁高效转化备受关注,尤其是高硫炼焦煤中有机硫的调控至关重要。煤热解过程中,有机硫的变迁始于煤大分子结构中C–S键的断裂和含硫自由基的稳定,活性氢/氧是影响其转化赋存形态的重要因素。研究表明,煤在富氢/氧氛围下热解或与生物质、含氧有机物共热解的体系中,含有的活性氢/氧可弱化有机硫的C–S键,促进其断裂并及时结合生成的含硫自由基,促进煤中硫分向气相变迁,减少了含硫自由基与煤基质的二次反应。同时,高挥发分煤与高硫煤共热解过程中,相对丰富的挥发分中的活性氢/氧也会影响高硫煤中有机硫的变迁,降低焦炭中的硫含量,这为煤中硫分定向调控提供了理论基础。     

淖毛湖煤加氢液化过程杂原子迁移转化研究

以淖毛湖煤为原料,进行加氢直接液化,考察了加氢温度与转化率和油收率的关系,并解析了加氢条件下煤中硫、氮和氧的迁移转化特性。结果表明,淖毛湖煤具有良好的液化性能,400℃和2 MPa氢初压条件下即可达到69.6%的转化率和55.3%的油产率。结合气相色谱质谱联用(GC-MS)和气相色谱-原子发射光谱(GC-AED)等方法对产物分析发现,以弱键合结构存在的硫、氮和氧等杂原子易发生加氢裂解生成H2S、NH3、H2O等。液化油品中含硫化合物主要以噻吩及噻吩同系物为主;含氮化合物含量极低,主要由含氮杂环化合物构成;含氧化合物在液化油中主要以酚及酚的同系物为主。存在于芳香结构中的杂原子会随着自由基缩合反应,生成更稳定的含杂原子稠环化合物富集在液化残渣中。     

锂硫电池电解质研究进展

锂硫电池由于其高能量密度(理论高达2600 Wh/kg)、低成本、环境友好等优点而广受关注. 但是锂硫电池仍存在正极活性物质利用率低、循环性能差等问题. 造成这些问题的主要原因是易溶于有机电解液的中间产物聚硫锂Li₂S_n (4≤n≤8)和不溶于有机电解液的硫化锂造成的. 简要介绍了锂硫电池体系的主要问题,并结合本研究小组的研究,对锂硫电池用电解质体系从有机电解液组成、电解液添加剂、聚合物电解质和无机固体电解质等方面进行了详细的综述,最后对电解质的发展前景进行了展望.     

裂解汽油中噻吩硫在Co-Mo/Al2O3上的催化加氢宏观动力学

采用绝热管式固定床积分反应器，在2.5MPa~3.9MPa、513K~655K、氢/裂解汽油摩尔比1.8~3.5和裂解汽油中噻吩、单甲基噻吩和双甲基噻吩质量分数为838×10－6、137×10－6~723×10－6和192×10－6~723×10－6下，对Co-Mo/Al2O3催化剂上裂解汽油催化加氢脱硫的宏观动力学进行了研究。以Powell优化法和Merson迭代法对动力学实验数据进行非线性参数估值，建立了良好吻合实验数据的、裂解汽油催化加氢脱硫的幂函数型宏观动力学模型。噻吩、单甲基噻吩和双甲基噻吩的反应级数分别为0.721、0.735和0.87，对应的加氢反应宏观活化能依次为70.0kJ·mol－1、67.9kJ·mol－1和59.9kJ·mol－1。各噻吩基硫的转化率均随反应压力的提高而增加，3.5MPa以上时，增加的趋势减缓；反应温度的提高有利于噻吩基硫转化率的增加；593K以上时，各硫化物的转化率随温度的增加呈现线性增加的趋势。     

聚噻吩类电致变色材料的研究进展

电致变色材料广泛应用于显示屏、智能窗、国防军事伪装等各方面,得到了人们的广泛关注。本文介绍了聚噻吩及其衍生物的变色机理,综述了聚噻吩、PEDOT、D-A型材料、D-A-D型材料、噻吩共聚物及其有机/无机纳米复合材料的性能及其研究进展,并简要介绍了噻吩类电致变色材料的应用前景,指出合成颜色变化丰富、稳定性和成膜性好、易加工、并有很好导电性能的D-A-D材料、共聚物及其有机/无机纳米复合材料是聚噻吩类电致变色材料发展的主要趋势。     

汽油中有机硫化物的酸富集和结构分析

石油中发现的硫化物已超过250种，其中约有1／4存在于汽油中。由于汽油中每种硫化物的含量都很低，又有十分复杂的烃组分和含氮组分的干扰，单纯使用仪器方法对汽油中的有机硫化物进行结构分析是十分困难的。通常的做法是对汽油样品进行预处理，使硫化物从混合烃体系中分离出来，再通过仪器和相应标样进行类型分析或结构鉴定。目前研究者在此方面做了很多工作，花瑞香等用29种硫化物标样，采取GC／SCD辅以选择性化学反应对汽油馏分的硫化物形态分布研究。     

Automotive Gasoline Quality Analysis by Gas Chromatography: Study of Adulteration

Summary The addition of organic solvents (light aliphatic, heavy aliphatic and aromatic hydrocarbons) in Brazilian gasoline is unfortunately very frequent, and this illicit practice impares gasoline quality. Gas chromatography (GC) and gas chromatography coupled to mass spectrometry (GC-MS) analyses can be used as a procedure to improve the detection of adulterated gasoline. The results showed that adulterated samples and also the type of organic solvent used in adulteration can be detected by comparison of chromatographic profiles (standard samples versus adulterated samples). However, a single GC analysis can detect an adulterated gasoline, and so decrease the number of adulterated samples approved as presenting good quality.     

选择性反应结合气相色谱进行汽油硫化物分析

通过3个分别针对硫醇、硫醚和含α-H噻吩的官能团选择性反应,结合连有脉冲火焰光度检测器的毛细管气相色谱对汽油中各类硫化物进行区分,实现了汽油中不同类型有机硫化物的快速分析.经过化学反应处理的汽油样品谱图逐步简化,方便了对不同类型硫化物的归属,也在一定程度上解决了叠合峰的辨别和归属问题.对汽油样品的实际分析研究表明,其中的有机硫化物主要以噻吩及其衍生物的形式存在,也含有一部分硫醚,硫醇最少.     

重整生成汽油样品中烃的类别分析

用气相色谱以程序升温方式分析了重整生成汽油,并将各组分升温保留时间转换为恒温保留指数。以各组分在ＯＶ－１和ＳＥ－５４固定相上,同一柱温下的保留指数差及在各柱上的温度系数为三因素进行斜交因子分析和本征矢量旋转,给出了重整生成汽油样品中烷烃、烯烃、环烷烃、芳烃值,经气相色谱－质谱分析验证了结果的正确性,为重整成成汽油样品中烃的类别分析提供了一种新方法。     

烷基化汽油中烃的类别分析

在程序升温条件下，用气相色谱法分析烷基化汽油样品，将各组分的程序升温保留时间转化的恒温保留指数。根据各组分在SE-54固定相和OV-1固定相上的气相色谱保留指数差对其进行类别定性。利用色谱-质谱分析法进行了验证，结果表明该方法简便可行。     

Sorption and transport behavior of gasoline components in polyethylene glycol membranes

Desulphurization mechanism of polyethylene glycol (PEG) membranes has been investigated by the study of solubility and diffusion behavior of typical gasoline components through PEG membranes with various crosslinking degrees. The sorption, diffusion and permeation coefficients were calculated by the systematic studies of dynamic sorption curves of gasoline components such as thiophene, n-heptane, cyclohexane, cyclohexene and toluene in PEG membranes. Furthermore, the temperature dependence of diffusion and solubility coefficients and the influence of crosslinking degree on sorption and diffusion behaviors were conducted to elucidate the mass-transfer mechanism. According to the discussions on dynamic sorption curves, transport mode, activation energy and thermodynamic parameters, thiophene species were the preferential permeation components. Crosslinking is an effective modification way to improve the overall performance of PEG membranes applied in gasoline desulphurization. The pervaporation (PV) and gas chromatography (GC) experiments results corresponded to the conclusions. All these investigations will provide helpful suggestions for the newly emerged membrane desulphurization technology and complex organic mixture separation by pervaporation.     

Fingerprint identification of volatile organic compounds in gasoline contaminated groundwater using gas chromatography differential ion mobility spectrometry

Groundwater can be contaminated when e.g. gasoline tanks leak. Due to sampling and lab analysis, groundwater monitoring is time consuming and expensive. The technologies developed for rapid on-site analysis of gasoline contaminated groundwater face the technical limitation to distinguish the gasoline from complex matrices. In the present study the fingerprint identification of volatile organic components (VOCs) in gasoline contaminated groundwater using gas chromatography (GC) differential ion mobility spectrometry (DMS) is investigated. Groundwater was spiked with five sorts of gasoline (one reformulated gasoline, gasoline without additives and three different brand gasoline collected on petrol stations) and analyzed by GC-DMS. Seven VOCs (benzene, toluene, ethyl benzene, m-xylene, p-xylene, o-xylene, 1,2,4-trimethylbenzene) were identified by GC mass spectrometry (GC-MS) as well as by GC-DMS and selected as markers. The semi-quantitative determination of the selected compounds was achieved. The limits of detection of the GC-DMS are 46.42?ng for benzene, 1.13?ng for toluene, 1.80?ng for ethylbenzene, 0.22?ng for m-xylene, 1.13?ng for p-xylene, 0.61?ng for o-xylene and 0.37?ng for 1,2,4-trimethylbenzene, respectively. These results reveal the feasibility of GC-DMS for on-site monitoring of contaminated groundwater.     

焦化汽油中硫化物类型分布的气相色谱-硫化学发光检测方法

建立了焦化汽油中硫化物类型分布的气相色谱-硫化学发光检测分析方法。考察了色谱条件对焦化汽油中各种硫化物分离的影响,定性了某焦化汽油中的74个硫化物。以硫化氢、乙硫醇、正丙硫醇、噻吩、2-甲基噻吩、2-乙基噻吩、2-丙基噻吩、碳四噻吩(tR=40.28 min)、苯并噻吩、甲基苯并噻吩(tR=58.13 min)的保留时间为尺度,计算了焦化汽油中各种硫化物的保留指数,并可推广到其他类型的汽油馏分中各种硫化物保留指数的计算,为仅能提供硫化物信息的仪器提供了可靠的定性依据。焦化汽油中几种主要硫化物(异丙硫醇、正丙硫醇、正丁硫醇、2-甲基噻吩、3-甲基噻吩、2,4-二甲基噻吩、2,3,4-三甲基噻吩)含量测定值的相对标准偏差均小于5%。当信噪比为3时,测得硫的检测限为0.05 mg/L。研究发现:同其他类型的汽油相比,焦化汽油的硫含量较高且所含硫醇比例明显偏高,2-甲基噻吩和3-甲基噻吩的含量差别较大。该法可为加氢脱硫催化剂和工艺的研究提供数据。     

Use of ZSM-5 catalyst in deoxygenation of waste cooking oil

This study investigated the potential use of waste cooking oil (WCO) in the production of engine fuels and valuable chemicals via catalytic cracking. WCO was processed in its pure form and in a mixture with hydrotreated vacuum gas oil (HVGO). Catalytic cracking experiments were performed using a microactivity test (MAT) (simulation of the fluid catalytic cracking environment). In cracking over the standard fluid catalytic cracking equilibrium catalyst (FCC-ECAT), the oxygen contained in the feed was consumed in the formation of CO and CO₂, water and into oxygenated organic compounds (phenolics, esters, carboxylic acids, etc.), which were found in the organic phase of the liquid product. In order to remove the unwanted organic oxygenates, the catalytic system based on pure FCC-ECAT was modified by addition of the ZSM-5-based FCC catalyst. By using the mixture containing FCC-ECAT and 10 mass % of FCC-ZSM-5, it was possible to reduce the amount of organic oxygenates to almost the feasible minimum when cracking pure WCO. The effect of the catalyst mixture on cracking the feed mixture of the vacuum gas oil with 10 vol. % of WCO was manifested in the practically zero formation of organic oxygenates and in a gasoline yield comparable with vacuum gas oil (VGO) cracking.     

Separation of dialkyl sulfides by metallo-mesogenic stationary phases for complexation gas chromatography

A copper mesogenic side-chain polymer (P-C(15)CuC(18)) was cross-linked onto the capillary wall as a stationary film for gas chromatography (GC) separation of alkyl sulfides. These organic sulfides are of interest for their large health impact because of their wide range of volatiles and high reactivities toward metals. Different GC parameters for optimal separation efficiency are discussed for use with a mesogenic polymer column along with flame photometric detection (FPD). Both the carrier gas flow-rate and column temperature were studied to determine the relationship of plate height to the chemical structure of the solutes, as well as to determine the morphology of the mesogenic polymer. Van 't Hoff plots show phase transitions of the stationary mesophase as the column temperature was varied. The results reveal that the separation mechanism might be based on ligand exchange and polarity interaction between the analytes and the stationary phase, with the vapor pressure of the analytes also being important. The former interaction dominates in the lamellar crystalline phase and the latter interaction dominates in the hexagonal columnar-discotic phase. With high reproducibility for retention time (RSD< or =0.37%) and for peak area (RSD< or =5.16%), the GC-FPD system produced linear calibration graphs (r> or =0.9918) for the determination of 13 sulfides with a detection limit below 2.5 ng.