High‐Performance Förster Resonance Energy Transfer (FRET)‐Based Dye‐Sensitized Solar Cells: Rational Design of Quantum Dots for Wide Solar‐Spectrum Utilization

High‐performance Förster resonance energy transfer (FRET)‐based dye‐sensitized solar cells (DSSCs) have been successfully fabricated through the optimized design of a CdSe/CdS quantum‐dot (QD) donor and a dye acceptor. This simple approach enables quantum dots and dyes to simultaneously utilize the wide solar spectrum, thereby resulting in high conversion efficiency over a wide wavelength range. In addition, major parameters that affect the FRET interaction between donor and acceptor have been investigated including the fluorescent emission spectrum of QD, and the content of deposited QDs into the TiO₂ matrix. By judicious control of these parameters, the FRET interaction can be readily optimized for high photovoltaic performance. In addition, the as‐synthesized water‐soluble quantum dots were highly dispersed in a nanoporous TiO₂ matrix, thereby resulting in excellent contact between donors and acceptors. Importantly, high‐performance FRET‐based DSSCs can be prepared without any infrared (IR) dye synthetic procedures. This novel strategy offers great potential for applications of dye‐sensitized solar cells.     

Synthesis of ZnO nanorods and their application in quantum dot sensitized solar cells

ZnO nanorod thin films of different thicknesses and CdS quantum dots have been prepared by chemical method. X-ray diffraction pattern reveals that the CdS quantum dot and ZnO nanorods are of hexagonal structure. Field emission scanning electron microscope images show that the diameter of hexagonal shaped ZnO nanorods ranges from 110 to 200 nm and the length of the nanorod vary from 1.3 to 4.7 μm. CdS quantum dots with average size of 4 nm have been deposited onto ZnO nanorod surface using successive ionic layer adsorption and reaction method and the assembly of CdS quantum dot with ZnO nanorod has been used as photo-electrode in quantum dot sensitized solar cells. The efficiency of the fabricated CdS quantum dot-sensitized ZnO nanorod-based solar cell is 1.10 % and is the best efficiency reported so far for this type of solar cells.     

Label-free Photoelectrochemical Aptasensor for the Determination of Carcinoembryonic Antigen Using a Cadmum Sulfide Quantum Dot Sensitized Titanium (IV) Oxide Nanotube Electrode

A label-free photoelectrochemical aptasensor for the sensitive and selective determination of carcinoembryonic antigen was constructed based on a CdS quantum dot sensitized TiO₂ nanotube electrode. TiO₂ nanotubes with highly ordered structure and more active sites than bulk TiO₂ were prepared with an electrochemical anodic oxidation process. The CdS quantum dots were immobilized on the TiO₂ nanotubes using poly(diallyldimethylammonium chloride) as a bridge. Due to the energy level match between TiO₂ and CdS, the CdS quantum dots/TiO₂ nanotubes electrode exhibits excellent photoelectrochemical performance. The large surface area of the electrode also allows for capturing large numbers of aptamers. The fine photoelectrochemical performance and the large surface area of the electrode greatly enhanced the detection sensitivity. Under the optimal conditions, the prepared photoelectrochemical aptasensor presents desirable analytical properties for the determination of carcinoembryonic antigen in the range of 0.05 to 10?ng?mL^?1 with a detection limit of 0.014?ng?mL^?1. The application of the designed protocol was investigated by analyzing carcinoembryonic antigen in human serum samples with recoveries from 80.0 to 115.0%. This simple and sensitive method provides an alternative tool to standard biochemical assays.     

CdS/TiO2–SrTiO3 heterostructure nanotube arrays for improved solar energy conversion efficiency

TiO₂–SrTiO₃ heterostructure nanotube arrays have been utilized as a novel oxide substrate for CdS quantum dot sensitized solar cells (QDSCs). SrTiO₃ on TiO₂ surface passivates surface states of TiO₂ and builds cascade-structured band alignment, which significantly reduces charge recombination at electrode surface. CdS/TiO₂–SrTiO₃ electrode exhibits a superior photoelectrochemical performance than CdS/TiO₂ electrode with ～ 70% increase in external quantum efficiency. This study suggests that the suppression of charge recombination at electrode surface is critical to efficient solar energy conversion.     

Unpredicted electron injection in CdS/CdSe quantum dot sensitized ZrO2 solar cells

A quantum dot sensitized solar cell based on a porous ZrO(2) film, sensitized with CdSe quantum dots using CdS as an intermediate layer is presented. We observe electron injection from photo-excited quantum dots into the ZrO(2), which is unexpected due to the much higher conduction band edge (closer to the vacuum level) of bulk ZrO(2) compared to TiO(2).     

Energy Relay from an Unconventional Yellow Dye to CdS/CdSe Quantum Dots for Enhanced Solar Cell Performance

A new design for a quasi‐solid‐state Forster resonance energy transfer (FRET) enabled solar cell with unattached Lucifer yellow (LY) dye molecules as donors and CdS/CdSe quantum dots (QDs) tethered to titania (TiO₂) as acceptors is presented. The Forster radius is experimentally determined to be 5.29 nm. Sequential energy transfer from the LY dye to the QDs and electron transfer from the QDs to TiO₂ is followed by fluorescence quenching and electron lifetime studies. Cells with a donor–acceptor architecture (TiO₂/CdS/CdSe/ZnS‐LY/S^2?‐multi‐walled carbon nanotubes) show a maximum incident photon‐to‐current conversion efficiency of 53 % at 530 nm. This is the highest efficiency among Ru‐dye free FRET‐enabled quantum dot solar cells (QDSCs), and is much higher than the donor or acceptor‐only cells. The FRET‐enhanced solar cell performance over the majority of the visible spectrum paves the way to harnessing the untapped potential of the LY dye as an energy relay fluorophore for the entire gamut of dye sensitized, organic, or hybrid solar cells.     

Quantum dots co-sensitized solar cells: a new assembly process of CdS/CdSe linked to mesoscopic TiO2-nano-SiO2 hybrid film

A green and simple method was found to prepare CdS/CdSe co-sensitized photoelectrodes for the quantum dots sensitized solar cells application. All the assembly processes of CdS and CdSe quantum dots (QDs) were carried out in aqueous solution. CdS and CdSe QDs were sequentially assembled onto TiO₂-nano-SiO₂ hybrid film by two steps. Firstly, CdS QDs were deposited in situ over TiO₂-nano-SiO₂ hybrid film by the successive ionic layer adsorption and reaction (SILAR) process in water. Secondly, using 3-mercaptopropionic acid (3-MPA) as a linker molecule, the pre-prepared colloidal CdSe QDs (~3.0 nm) dissolved in water was linked onto the TiO₂-nano-SiO₂ hybrid film by the self-assembled monolayer technique with the mode of dropwise. The mode is simple and advantageous to saving materials and time. The results show that the photovoltaic performance of the cells is enhanced with the increase of SILAR cycles for TiO₂-nano-SiO₂/CdS photoelectrode. The power conversion efficiency of 2.15 % was achieved using the co-sensitization photoelectrode prepared by using 6 SILAR cycles of CdS plus CdSe (TiO₂-nano-SiO₂/CdS(6)/CdSe) under the illumination of one sun (AM1.5, 100 mW/cm²).     

CdS and CdSe quantum dots subsectionally sensitized solar cells using a novel double-layer ZnO nanorod arrays

We report a novel approach for synthesizing CdS and CdSe quantum dots subsectionally sensitized double-layer ZnO nanorods for solar cells, which are comprised of CdS QDs-sensitized bottom-layer ZnO NRs and CdSe QDs-sensitized top-layer ZnO NRs. X-ray diffraction study and scanning electron microscopy analysis indicate that the solar cells of subsectionally sensitized double-layer ZnO NRs, which are the hexagonal wurtzite crystal structure, have been successfully achieved. The novel structure enlarged the range of absorbed light and enhanced the absorption intensity of light. The I-V characteristics show that the double-layer structure improved both the current density (J_sc) and fill factor (FF) by 50%, respectively, and power conversion efficiency (η) was increased to twice in comparison with the CdS QDs-sensitized structure.     

An efficient method to prepare high-performance dye-sensitized photoelectrodes using ordered TiO<Subscript>2</Subscript> nanotube arrays and TiO<Subscript>2</Subscript> quantum dot blocking layers

High-performance dye-sensitized photoelectrodes using ordered TiO₂ nanotube arrays (TNTs) and TiO₂ quantum dot blocking layers are fabricated. The free-standing TNT membranes with perfect ordered morphology are prepared by three times of anodic oxidation on Ti foils. These TNT membranes can be easily transported to conductive glasses to fabricate front-side illuminated photoelectrodes. By changing anodic oxidation duration, the thickness of TNT membranes can be controlled, which shows significant influence on the UV-Vis reflectance and absorption abilities of TNT-based photoelectrodes and further influence photovoltaic performance of dye-sensitized solar cells (DSSCs). The highest power conversion efficiency (PCE) of DSSCs about 6.21 % can be obtained by using TNT membranes prepared with anodic oxidation of 3 h. For further improving photovoltaic performance of DSSCs, TiO₂ quantum dot (QDs) blocking layers are inserted between conductive glasses and TNT membranes in the photoelectrodes, which show remarkable effects. The highest PCE of DSSCs with this kind of blocking layers can increase to 8.43 %, producing 35.75 % enhancement compared with that of the counterparts without TiO₂ QD blocking layers.     

Improved performance of dye sensitized ZnO nanorod solar cells prepared using TiO2 seed layer

Zinc oxide (ZnO) nanorods of different structures have been grown on indium-doped tin oxide substrates by using TiO₂ as seed layer. The ZnO nanorods have been prepared using TiO₂ seed layers annealed at different temperatures via a simple sol–gel method. The X-ray diffraction result indicates that the prepared samples are of wurtzite structure. Dye sensitized solar cells have been fabricated using the prepared ZnO nanorods. The open circuit voltage, short circuit current density, fill factor, and power conversion efficiency of the ZnO nanorod based dye sensitized solar cells prepared using TiO₂ seed layers annealed at different temperatures have been determined. The improvement in power conversion efficiency may be due to the flower like structured ZnO nanorods with smaller diameter and large specific surface area which paves way for the efficient electron transfer in hybrid solar cells.     

锰掺杂硒硫化镉光阳极的制备与光电性能

将适量Se加入到Na2S甲醇水溶液中反应生成Na₂SSe₂阴离子前驱体, 以Cd(NO₃)2、Mn(CH3COO)2为阳离子前驱体, 通过连续离子层吸附反应(SILAR)分别制备出CdSSe₂/TiO₂或 MN²⁺掺杂的Mn-CdSSe₂/TiO₂量子点敏化光阳极。采用拉曼光谱、X射线光电子能谱和能量色散X射线能谱分析确定阴离子前驱体和量子点的价键结构和组成;通过紫外可见吸光光谱表征量子点的光吸收性能;利用J-V曲线和IPCE分别对CdS、CdSSe₂和Mn-CdSSe₂量子点敏化的TiO₂光阳极的光电性能进行了表征。实验结果表明, 采用 0.12 mol·L^-1 Se和0.5 mol·L^-1 Na2S制备的阴离子前驱体、0. 5 mol·L^-1 Cd²⁺和 0.3 mol·L^-1 MN²⁺阳离子前驱体, 通过SILAR法制备的Mn-CdSSe₂/TiO₂光阳极, 能量转换效率比CdSSe₂/TiO₂和CdS/TiO₂光阳极分别提高了90%和247%。     

Graphitic-C<Subscript>3</Subscript>N<Subscript>4</Subscript> quantum dots decorated {001}-faceted TiO<Subscript>2</Subscript> nanosheets as a 0D/2D composite with enhanced solar photocatalytic activity

Zero-dimensional (0D)/two-dimensional (2D) heterojunctions have attracted great attention in photocatalysis due to their superior interfacial effects. In this work, 0D g-C₃N₄ quantum dots (CNQDs) were firstly used to modify {001}-faceted 2D TiO₂ nanosheets by a simple solvothermal method. During the controlled growth of TiO₂ nanosheets with exposed reactive {001} facets, the CNQDs can be simultaneously assembled on the surface of TiO₂ nanosheets in a highly dispersive way. The 0D/2D composite containing only 0.5% of CNQDs shows the optimized solar photocatalytic activity for the degradation of rhodamine B and 4-chlorophenol. More importantly, the 0D/2D composite exhibits a better solar photocatalytic activity than the bulk g-C₃N₄/TiO₂ nanosheets composite. This improvement can be ascribed to the close interfacial contact and strong interaction between the highly dispersed CNQDs and the TiO₂ nanosheets, which could lead to efficient separation of the photogenerated electron–hole pairs, provide more catalytic active sites, and enhance the absorption of solar light. The 0D/2D composite also shows good stability for its practical applications.     

Stability of CdS-coated TiO<Subscript>2</Subscript> solar cells

The obstacle to realize the large-scale production of dye-sensitized solar cells (DSSCs) is its long-term stability and reliability problem. One of the main causes of the instability of DSSCs is the use of liquid electrolytes. In addition, exploring nano-sized particles of CdS as an alternative sensitizer for organic dye in dye-sensitized solar cells have attracted great interest due to the high cost and the instability of the organic dye. Our study has found that the CdS-coated TiO₂ cell degrades rapidly in the liquid electrolytes even under dark environment. In this work, a solid-state solar cell structure of Glass/FTO/TiO₂/CdS:Cu/FTO/glass was successfully made with an efficiency of 0.7%. CdS:Cu served as both the p-type conductor and absorber. No efficiency was obtained for cell structures of glass/FTO/TiO₂/CdS/FTO/glass. This indicates the effectiveness of hole conducting behavior of CdS:Cu. This is the first time that this type of solid-state solar cell is reported and improved stability is demonstrated.     

锰掺杂硒硫化镉光阳极的制备与光电性能

将适量Se加入到Na₂S甲醇水溶液中反应生成Na₂SSe₂阴离子前驱体, 以Cd(NO₃)₂、Mn(CH₃COO)₂为阳离子前驱体, 通过连续离子层吸附反应(SILAR)分别制备出CdSSe₂/TiO₂或 Mn²⁺掺杂的Mn-CdSSe₂/TiO₂量子点敏化光阳极。采用拉曼光谱、X射线光电子能谱和能量色散X射线能谱分析确定阴离子前驱体和量子点的价键结构和组成;通过紫外可见吸光光谱表征量子点的光吸收性能;利用J-V曲线和IPCE分别对CdS、CdSSe₂和Mn-CdSSe₂量子点敏化的TiO₂光阳极的光电性能进行了表征。实验结果表明, 采用 0.12 mol·L^-1 Se和0.5 mol·L^-1 Na₂S制备的阴离子前驱体、0.5 mol·L^-1 Cd²⁺和 0.3 mol·L^-1 Mn²⁺阳离子前驱体, 通过SILAR法制备的Mn-CdSSe₂/TiO₂光阳极, 能量转换效率比CdSSe₂/TiO₂和CdS/TiO₂光阳极分别提高了90%和247%。     

The performance of coupled (CdS:CdSe) quantum dot-sensitized TiO2 nanofibrous solar cells

Highly porous networks and reduced grain boundaries with one-dimensional (1-D) nanofibrous morphology offer enhanced charge transport in solar cells applications. Quantum dot (QDs) decorated TiO₂ nanofibrous electrodes, unlike organic dye sensitizers, can yield multiple carrier generations due to the quantum confinement effect. This paper describes the first attempt to combine these two novel approaches, in which CdS (～18 nm) and CdSe (～8 nm) QDs are sensitized onto electrospun TiO₂ nanofibrous (diameter ～80–100 nm) electrodes. The photovoltaic performances of single (CdS and CdSe) and coupled (CdS/CdSe) QDs-sensitized TiO₂ fibrous electrodes are demonstrated in sandwich-type solar cells using polysulfide electrolyte. The observed difficulties in charge injection and lesser spectral coverage of single QDs-sensitizers are solved by coupling (CdS:CdSe) two QDs-sensitizers, resulting in a enhanced open-circuit voltage (0.64 V) with 2.69% efficiency. These results suggest the versatility of fibrous electrodes in QDs-sensitized solar cell applications.     

CdS‐Encapsulated TiO2 Nanotube Arrays Lidded with ZnO Nanorod Layers and Their Photoelectrocatalytic Applications

A novel TiO₂ nanotube array/CdS nanoparticle/ZnO nanorod (TiO₂ NT/CdS/ZnO NR) photocatalyst was constructed which exhibited a wide‐absorption (200–535 nm) response in the UV/Vis region and was applied for the photoelectrocatalytic (PEC) degradation of dye wastewater. This was achieved by chemically assembling CdS into the TiO₂ NTs and then constructing a ZnO NR layer on the TiO₂ NT/CdS surface. Scanning electron microscopy (SEM) results showed that a new structure had been obtained. The TiO₂ NTs looked like many “empty bottles” and the ZnO NR layer served as a big lid. Meanwhile the CdS NPs were encapsulated between them with good protection. After being sensitized by the CdS NPs, the absorption‐band edge of the obtained photocatalyst was obviously red‐shifted to the visible region, and the band gap was reduced from its original 3.20 eV to 2.32 eV. Photoelectric‐property tests indicated that the TiO₂ NT/CdS/ZnO NR material maintained a very high PEC activity in both the ultraviolet (UV) and the visible region. The maximum photoelectric conversion efficiencies of TiO₂ NT/CdS/ZnO NR were 31.8 and 5.98 % under UV light (365 nm) and visible light (420–800 nm), respectively. In the PEC oxidation, TiO₂ NT/CdS/ZnO NR exhibited a higher removal ability for methyl orange (MO) and a high stability. The kinetic constants were 1.77×10^?4 s^?1 under UV light, which was almost 5.9 and 2.6 times of those on pure TiO₂ NTs and TiO₂ NT/ZnO NR, and 2.5×10^?4 s^?1 under visible light, 2.4 times those on TiO₂ NT/CdS.     

Nanosized TiO<Subscript>2</Subscript> particles decorated on SiO<Subscript>2</Subscript> spheres (TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript>): synthesis and photocatalytic activities

Nanosized TiO₂ and nano-anatase TiO₂ decorated on SiO₂ spherical core shells were synthesized by using a sol–gel method. The synthesized pure TiO₂ nano particle and TiO₂ grafted on SiO₂ sphere with various ratios have been characterized for their structure and morphologies by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectrophotometry (FTIR) and transmission electron microscopy (TEM). Their surface areas were measured using the BET method. The photocatalytic activity of all nanocomposites was investigated using methylene blue as a model pollutant. The synthesized TiO₂/SiO₂ particles appeared to be more efficient in the degradation of methylene blue pollutant, as compared to pure TiO₂ particles.     

Controllable incorporation of CdS nanoparticles into TiO<Subscript>2</Subscript> nanotubes for highly enhancing the photocatalytic response to visible light

A constant current electrochemical deposition was employed to incorporate CdS nanoparticles into the TiO₂ nanotube arrays (TiO₂NTs). The size and amount of CdS nanoparticles in TiO₂NTs (CdS@TiO₂NTs) were controllable via modulating current, deposition time and electrolyte concentration. It was revealed, from the scanning electron microscopy (SEM) images and X-ray photoelectron spectroscopy (XPS) in depth profile, that CdS nanoparticles were filled into TiO₂ nanotubes. A shift of the absorption edge toward the visible region under the optimal electrodeposition condition was observed with the diffuse reflectance spectroscopy (DRS). A 5-fold enhancement in the photocurrent spectrum for TiO₂NTs was observed and the photocurrent response range was significantly extended into the visible region because of the CdS incorporation. Compared with pure TiO₂NTs, under a visible light irradiation, CdS@TiO₂NTs exhibited a 3.5-fold improvement of photocatalytic activity, which was demonstrated by the photocatalytic decomposition of Rhodamine B (RhB).     

CuInS2量子点敏化太阳能电池中尺寸依赖的电子注入和光电性质

研究了CuInS₂（CIS）量子点敏化太阳能电池（QDSSCs）的电子注入和器件性能与粒子尺寸之间的依赖关系. 首先合成了不同尺寸的CuInS₂量子点（QDs）,制备了CuInS₂量子点敏化的TiO₂薄膜,并组装了量子点敏化太阳能电池. 通过循环伏安法确定了CuInS₂量子点的能级位置. 采用时间分辨荧光光谱分析测量了CuInS₂量子点到TiO₂薄膜的电子转移速率和效率. 结果发现,随着粒子尺寸从4.0 nm减小到2.5 nm,电子注入速率略微增加而电子注入效率减小,同时量子点敏化太阳能电池的开路电压基本不变,而光电转换效率、短路电流和填充因子（FF）均减小. 上述研究结果表明量子点敏化太阳能电池性能的优化可以通过改变量子点的尺寸来实现.     

Sub‐Bandgap Excitation‐Induced Electron Injection from CdSe Quantum Dots to TiO2 in a Directly Coupled System

We show that the sub‐bandgap excitation of a directly coupled CdSe quantum dot (QD)–TiO₂ system induces electron injection from CdSe levels to the conduction band of TiO₂, leading to spectral extension of the light response. We anticipate that this study presents a useful guideline for improving the conversion efficiency of QD‐sensitized solar cells.