脲甲醛缩聚物制备电子墨水微胶囊研究

在原位聚合法制备脲甲醛树脂微胶囊的过程中 ,使用水溶性低分子量脲甲醛缩聚物代替传统的脲甲醛预聚体 (一羟甲基脲、二羟甲基脲 )作为反应单体 ,由于脲甲醛缩聚物比后者更容易吸附在分散相液滴表面 ,解决了用原位聚合法制备脲甲醛微胶囊所常有的结块、粘连、表面粗糙、产率低的问题 .研究了低分子量脲甲醛缩聚物水溶液的粘度特征和表面活性及其与胶囊包封率的关系 .使用这种方法制备出了电子墨水微胶囊     

含P204聚酰胺胶囊的功能性研究

功能性超薄聚酰胺胶囊作为一类新型的合成仿生膜体,具有芯材体积大、膜壁强度高、表面积容易测定及双层膜稳定性好等优点.我们采用超薄聚酰胺作为支撑体,在多孔胶囊壁中含浸双亲分子P204[二-(2-乙基己基)磷酸酯],使P204分子在胶囊壁孔隙中形成复合双层结构,结果芯材的渗透速度呈现出受化学反应和外电场控制的功能性.     

胶束增强型聚电解质微胶囊的制备

采用杂化碳酸钙微球作为模板, 利用LbL技术, 选择聚苯乙烯磺酸钠(PSS), 烯丙基胺的盐酸盐(PAH)和二烯丙基二甲基胺盐酸盐(PADA)聚电解质, 分别组装了PAH/PSS(弱/强)聚电解质胶囊和PADA/PSS(强/强)聚电解质微胶囊. 除去模板后得到了球形良好、分散均匀的聚电解质微胶囊. 研究结果表明, 利用杂化碳酸钙微球作为聚电解质微胶囊的模板, 得到的微胶囊的囊壁厚而致密, 同时, 由于组装采用的聚电解质的种类不同, 囊壁的微观形貌有较大差异.     

三聚氰胺-甲醛树脂包裹环氧树脂微胶囊的制备及表征

针对环氧树脂基材料的自修复,选取四氢邻苯二甲酸二缩水甘油酯作为芯材,采用三聚氰胺-甲醛树脂为壁材,对其进行微胶囊化包裹.结果表明,制得的具有单囊结构的环氧树脂微胶囊,胶囊粒径较小(约6.7μm)、囊壁较薄(约0.2μm)、芯含量较高(83.2 wt%),囊壁内、外表面光滑致密,胶囊具有良好的密闭性和耐热性;在微胶囊化过程中,三聚氰胺-甲醛树脂的缩聚反应动力学起关键作用,芯材没有参与囊壁形成的交联反应;包裹后的芯材活性保持不变,胶囊被复合到材料过程中囊芯活性也保持不变;胶囊的强度较高,能承受与基体材料复合过程中的外力作用,且与基体材料间粘结良好,在裂纹形成过程中能够随基体同时开裂.     

改性胺微胶囊固化剂制备工艺的优化与性能

以改性胺1618固化剂为囊芯、脲醛树脂为壁材单体,采用界面聚合技术,成功制备了一种新型聚脲改性胺微胶囊固化剂。通过正交设计试验,考察了芯壁质量比、乳化剂种类和质量分数及搅拌速率对微胶囊包覆率、粒径大小及分布情况的影响,并确定了最佳制备工艺条件。采用马尔文激光粒度仪、扫描电镜对微胶囊粒径大小、分布情况及表面形貌进行表征,采用热重分析仪及傅里叶变换红外光谱对其化学结构进行表征,通过拉伸试验对自修复材料的断裂力学性能进行研究。结果表明,该微胶囊含有固化剂芯材,其热稳定温度为198°C,当芯壁质量比为0.7∶1、乳化剂为阿拉伯胶、乳化剂质量分数为1.5%、搅拌速率为800r/min时,所制备的微胶囊包覆率达到79.8%,平均粒径为207.5nm,呈规则的球形,分散性及表面致密性好。当基体材料中加入质量分数为1%的微胶囊后,拉伸强度提高64%,弹性模量提高287%。     

丙烯酸共聚物囊壁的正十八烷微胶囊的制备和性能表征

以二丙烯酸1,4-丁二醇酯为交联剂, 成功制备了甲基丙烯酸甲酯-甲基丙烯酸共聚物为壁材, 正十八烷为囊芯的相变材料微胶囊. 采用扫描电子显微镜(SEM)、差示扫描量热仪(DSC)和热重分析仪(TG)分别考察了单体与芯材投料比、单体浓度和交联剂的含量对微胶囊形貌、相变热性能、热稳定性能的影响. 实验结果表明: 随着单体与芯材投料比或单体浓度的增加, 微胶囊表面均变得致密, 壁厚增加; 随着交联剂含量的增加, 微胶囊的表面变得更加致密光滑, 热稳定性显著增强; 随着单体与芯材投料比的增大, 微胶囊热焓值减小, 被包裹的囊芯含量减少.     

正十六烷聚脲微胶囊化相变材料

用界面聚合法，合成了直径大约2.5 μm可用于热能储存含相变材料的聚脲包覆微胶囊.在含乳化剂的水溶液中，将溶有芯材正十六烷的有机相乳化成微米级油性液滴，随后加入的水溶性单体二胺与甲苯2,4-二异氰酸酯在胶束界面相互反应形成囊壁.分别用乙烯二胺，1,6-己二胺和它们的混合物作为水溶性单体进行了研究.并用红外光谱和热分析分别考察了不同胺类对微胶囊化学结构和热性质的影响.红外谱图显示合成了聚脲微胶囊，热重曲线表明含正十六烷的聚脲微胶囊能够耐受大约300 ℃高温，差示扫描量热测试表明所有样品均具有合适的相转变热，冷热循环实验揭示微胶囊能够维持储热容量不衰减.研究表明微胶囊化的正十六烷作为相变储热材料具有良好的应用前景.     

高效高分子酰化催化剂——含超亲核试剂聚酰胺的合成与表征

以４ 氨基吡啶为原料,制备各种含烷氨基吡啶基团的二元酰氯和二元胺反应性单体,再经缩聚反应得到聚酰胺型高分子超亲核催化剂．用气相色谱跟踪以聚酰胺催化的叔丁醇反应,结果表明,聚酰胺在酰化反应体系中有着良好的溶解性,含烷氨基吡啶基团的线型聚酰胺具有比４ （ Ｎ,Ｎ 二甲基氨基） 吡啶（ＤＭＡＰ） 更高的催化能力,而交联型树脂较其线型聚合物活性有所降低．     

LbL层层纳米自组装法制备新型微胶囊*

本文介绍了一种新颖、灵活的制备纳米或微米胶囊方法--层层纳米自组装法(LbL)。LbL法制备微胶囊的显著优越性在于能够在纳米尺度上对胶囊的大小、组成、结构、形态和囊壁厚度进行精确的控制.这种新型的微胶囊在生化、制药、药物控释、化妆品和催化等领域具有潜在的应用前景。     

高芯材含量聚苯乙烯石蜡微胶囊的制备及性能研究

为解决石蜡在使用过程中的一系列问题,以聚苯乙烯为壁材,58~#石蜡为芯材,采用悬浮聚合法制备了高芯材含量的微胶囊.考察了二己烯基苯(DVB)用量、芯壁比、复合改性时共聚单体种类和用量对微胶囊的影响.采用FT-IR、SEM、DSC、TG表征了微胶囊的结构、形貌、储热性能及热稳定性能.实验结果表明,DVB用量11%、芯壁比3∶1制备的微胶囊大小均匀,无团聚现象;交联改性的同时,加入20%MA单体共聚改性制备的微胶囊形貌好,热稳定性最佳,微胶囊中石蜡含量为91.7%时储热性能最优.     

单体结构对基于离子作用的自修复光固化材料性能的影响

本文研究了单体结构及其比例对基于离子作用的自修复光固化材料光聚合行为、力学性能,以及自修复性能的影响。结果表明：改变软硬单体种类及其比例不会改变自修复光固化体系的光聚合行为。增加软单体含量和降低硬单体含量,材料的拉伸应变和修复效率随之增加,断裂应力随之降低。硬单体中刚性环会增加聚合物链间的内摩擦力,使材料断裂应力增加,软单体中柔性醚链则降低链间范德华力,增强链移动性,提高材料的拉伸应变和修复效率。软单体为丙烯酸正丁酯（BA）及硬单体为丙烯酸异冰片酯（IBOA）的样品IB7-BA3展现出较好的综合性能,断裂应力为1.42 MPa,拉伸应变为295%,修复效率高于90%。     

Synthesis and characterization of a novel biodegradable,thermoplastic polyurethane elastomer

A series of biodegradable, thermoplastic polyurethane elastomers poly(?‐caprolactone‐co‐lactide(polyurethane [PCLA–PU] were synthesized from a random copolymer of L ‐lactide (LA) and ?‐caprolactone (CL), hexamethylene diisocyanate, and 1,4‐butanediol. The effects of the LA/CL monomer ratio and hard‐segment content on the thermal and mechanical properties of PCLA–PUs were investigated. Gel permeation chromatography, IR, ¹³C NMR, and X‐ray diffraction were used to confirm the formation and structure of PCLA–PUs. Through differential scanning calorimetry, tensile testing, and tensile‐recovery testing, their thermal and mechanical properties were characterized. Their glass‐transition temperatures were below ?8 °C, and their soft domains became amorphous as the LA content increased. They displayed excellent mechanical properties, such as a tensile strength as high as 38 MPa, a tensile modulus as low as 10 MPa, and an elongation at break of 1300%. Therefore, they could find applications in biomedical fields, such as soft‐tissue engineering and artificial skin. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5505–5512, 2006     

Novel compaction resistant and ductile nanocomposite nanofibrous microfiltration membranes

Despite promising filtration abilities, low mechanical properties of extraordinary porous electrospun nanofibrous membranes could be a major challenge in their industrial development. In addition, such kind of membranes are usually hydrophobic and non-wettable. To reinforce an electrospun nanofibrous membrane made of polyethersulfone (PES) mechanically and chemically (to improve wettability), zirconia nanoparticles as a novel nanofiller in membrane technology were added to the nanofibers. The compressive and tensile results obtained through nanoindentation and tensile tests, respectively, implied an optimum mechanical properties after incorporation of zirconia nanoparticles. Especially compaction resistance of the electrospun nanofibrous membranes improved significantly as long as no agglomeration of the nanoparticles occurred and the electrospun nanocomposite membranes showed a higher tensile properties without any brittleness i.e. a high ductility. Noteworthy, for the first time the compaction level was quantified through a nanoindentation test. In addition to obtaining a desired mechanical performance, the hydrophobicity declined. Combination of promising properties of optimum mechanical and surface chemical properties led to a considerably high water permeability also retention efficiency of the nanocomposite PES nanofibrous membranes. Such finding implies a longer life span and lower energy consumption for a water filtration process.     

THE PHYSICAL PROPERTIES OF POLY(2-HYDROXYETHYL METHACRYLATE) COPOLYMER HYDROGELS USED AS INTRAVAGINAL RINGS

Poly(2-hydroxyethyl methacrylate)(PHEMA)and poly(2-hydroxyethyl methacrylate-co-sodium methacrylate) [P(HEMA-co-SMA)]hydrogels with different compositions were prepared to be used as intravaginal rings,and their gelation time,water content,mechanical properties and morphology were investigated.The water content of PHEMA and P(HEMA-co-SMA) hydrogels decreased as the concentration of the monomer and the degree of crosslinking increased,while the water content significantly increased as the content of SMA,t...     

Breakthrough in the preparation of irradiated sodium alginate/polyethylene oxide blend films using methacrylate monomer

The present work is an attempt to prepare biodegradable films of sodium alginate (SA)/polyethylene oxide (PEO) blend tailored by methacrylate (MA) and γ irradiation following casting method. The effects of SA/PEO composition, glycerol as a plasticizer, methacrylate as a monomer, and radiation dose were investigated and it was found that the mechanical properties of the films strongly depend on the film-forming parameters. The incorporation of glycerol in the blend is crucial as it creates a suitable environment for monomer addition and points out that tensile strength of the films decreased, while the elongation at break increased. Moreover, it was found that the tensile properties were improved by the application of γ radiation as well as monomer treatment. The mechanical properties of the blend films integrated with MA monomer were higher than that without monomer at the analogous conditions. The structural and morphological features of the films were examined by Fourier transform infrared spectroscopy and scanning electron microscopy, respectively.     

Porous Molecular Capsules as Non-Polymeric Transducers of Mechanical Forces to Mechanophores

Mechanical grinding/milling can be regarded as historically the first technology for changing the properties of matter. Mechanically activated molecular units (mechanophores) can be present in various structures: polymers, macromolecules, or small molecules. However, only polymers have been reported to effectively transduce energy to mechanophores, which induces breakage of covalent bonds. In this paper, a second possibility is presented—molecular capsules as stress-sensitive units. Mechanochemical encapsulation of fullerenes in cystine-based covalent capsules indicates that complexation takes place in the solid state, despite the fact that the capsules do not possess large enough entrance portals. By using a set of solvent-free MALDI (sf-MALDI) and solid-state NMR (ss-NMR) experiments, it has been proven that encapsulation proceeds during milling and in this process hydrazones and disulfides get activated for breakage, exchange, and re-forming. The capsules are porous and therefore prone to collapse under solvent-free conditions and their conformational rigidity promotes the collapse by the breaking of covalent bonds.     

Highly active nanoreactors: nanomaterial encapsulation based on confined catalysis

It happens inside: highly active nanoreactors are prepared by encapsulating dendritic Pt nanoparticles (NPs) grown on a polystyrene template inside hollow porous silica capsules. The catalytic activity of these Pt NPs is preserved after encapsulation and template removal. Different metals, such as Ni, can thus be reduced inside the capsules, thereby leading to the formation of composites with tunable magnetic properties.     

新型可溶性聚芳酰胺及其共聚物的合成与性能研究

采用新型二胺 1,2 二氢 2 (4 氨基苯基 ) 4 [4 (4 氨基苯氧基 ) 苯基 ] 二氮杂萘 1 酮与对苯二甲酸、间苯二甲酸、萘二酸进行均聚或共聚 ,所得聚芳酰胺的Tg 均高于 30 0℃ ,且易溶于非质子极性溶剂中 ,聚合物的特性粘数为 1 2 6～ 1 5 1dL g(2 5℃ ,NMP) ,拉伸强度为 6 2～ 89MPa ,断裂伸长率为 5 %～ 9% ,拉伸模量为 2 2～ 2 9GPa ,电阻系数为 10 1 4 ～ 10 1 6     

Preparation and characterization of porous polymeric microspheres obtained from multifunctional methacrylate monomers

Synthesis and properties of the new difunctional methacrylate monomer 2‐hydroxy‐3‐methacryloyloxypropoxybenzene are presented. This monomer was applied for the synthesis of porous microspheres. It was copolymerized with trimethylolpropane trimethacrylate in the presence of two pairs of pore‐forming diluents dodecane and toluene, and n‐decanol and toluene. Influence of diluents composition on their porous structures was studied. Thermal resistance and tendency to swell in different organic diluents for a chosen sample were also determined. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6165–6174, 2008     

New tetrafunctional monomer 1,3‐di(2‐hydroxy‐3‐methacryloyloxypropoxy)benzene in the synthesis of porous microspheres

Synthesis and properties of the new aromatic tetrafunctional methacrylate monomer 1,3‐di(2‐hydroxy‐3‐methacryloyloxypropoxy)benzene are presented. This monomer was applied for the synthesis of porous microspheres. It was copolymerized with trimethylolpropane trimethacrylate in the presence of pore‐forming diluents, decan‐1‐ol and chlorobenzene. Influence of diluents composition on their porous structures was studied. Thermal resistance and tendency to swell in different organic diluents for a chosen sample were also determined. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3190–3201, 2009