壳聚糖膜对水杨酸吸附及释放过程的实时介电谱法研究

制备了壳聚糖膜,并且测量了壳聚糖膜/水杨酸溶液、含水杨酸的壳聚糖膜/蒸馏水两个膜/液体系的介电谱,在100～700 kHz频率范围,发现两种体系都存在显著的介电弛豫现象,而且该弛豫的特征参数随壳聚糖膜在相应溶液相中浸泡时间的不同而变化.将该体系介电模型化、并利用在Maxwell-Wagner界面极化理论上建立的公式对介电谱进行解析,得到了体系中两相--壳聚糖膜相和溶液相的介电常数和电导率随时间的变化曲线.通过分析电导变化曲线得知,壳聚糖膜对溶液中的水杨酸有吸附现象,而含有水杨酸的壳聚糖膜在蒸馏水中可以缓慢释放出水杨酸;吸附过程包含的机制有氢键的形成、疏水力和扩散;而水杨酸的脱附过程则包含吸附过程几种机制的逆反应.理论分析和解析结果都验证了介电谱方法对吸附和释放过程实时监测的有效性.     

壳聚糖超声可控降解及降解动力学研究

通过正交实验法考察了壳聚糖溶液浓度、反应温度、超声强度以及醋酸溶液浓度对超声降解反应的影响,确定了最佳反应条件,制备了一系列不同分子量的壳聚糖.研究了壳聚糖溶液浓度、反应温度以及壳聚糖原料分子参数与降解速率常数的关系.通过红外光谱、X-射线衍射和凝胶渗透色谱对降解产物进行了表征.结果表明,超声降解壳聚糖的最佳条件为10℃,壳聚糖溶液浓度2.5g/L.降解速率常数随壳聚糖溶液浓度和反应温度的降低而增大.高分子量和低脱乙酰度的壳聚糖原料有较高的降解速率和降解速率常数,壳聚糖原料的分子量对降解速率和降解速率常数的影响大于脱乙酰度对其的影响.超声波导致了壳聚糖分子量的降低和产物晶体结构的破坏,但没有改变产物的脱乙酰度和糖残基结构.     

固定化辣根过氧化酶的壳聚糖/二氧化硅杂化膜的制备及表征

利用生物相容性良好的天然高分子聚合物壳聚糖(C5)与四乙氧基硅烷(TEOS)通过原位溶胶-凝胶法制备壳聚糖／二氧化硅有机无机杂化复合膜,用杂化膜对辣根过氧化酶进行固定,用红外光谱法、扫描电镜法对膜进行了表征。以金电极和固定化酶膜构建过氧化氢生物传感器,并用循环伏安法和计时电流法对传感器的特性进行了研究。结果表明,用于研制固定化酶生物传感器时．杂化膜不仅对底物的响应时间快(小于10s）,而且能较好地保持酶的催化活性。求得酶促催化反应的表观米氏常数为0．87mmol／L。     

溶液共混法制备PMMA-Fe2O3杂化膜的研究

以甲基丙烯酸甲酯(MMA),α-Fe2O3纳米材料为原料,丙烯酸(AA)为交联剂,采用溶液共混法制备了PMMA-Fe2O3杂化膜。用IR,TG-DTA和SEM对杂化膜进行了测试,结果表明:PMMA通过-COO-Fe键与Fe2O3发生杂化,α-Fe2O3以10 nm~60 nm的形式分散在膜中。杂化膜的附着力、硬度、冲击强度、热稳定性明显优于纯PMMA。杂化膜具有良好的柔韧性和耐溶剂性能,其光泽度随搅拌时间的延长而增加。     

壳聚糖溶液pH对载细胞海藻酸钠-壳聚糖微胶囊性能的影响

以激光共聚焦扫描显微镜为研究手段, 原位直观地考察了在不同pH条件下聚电解质膜的络合程度和蛋白扩散情况. 通过分析pH值对微胶囊膜性能的影响规律, 并结合不同种类细胞对环境pH的敏感特性, 确定了制备细胞培养用海藻酸钠-壳聚糖微胶囊的最佳pH值. 结果表明, 当壳聚糖溶液的pH值由3.50增加到6.50, 微胶囊膜的络合深度呈现高-低-高的趋势, 而微胶囊膜的膨胀性能呈现低-高-低的趋势, 模型蛋白通过微囊膜的扩散呈现低-高-低的趋势, 拐点均出现在pH=4.00和5.50处. 结合动物细胞及微生物细胞对环境pH耐受能力的考察, 确定制备微囊化动物细胞时, 微胶囊成膜反应溶液的最佳pH值为5.50; 制备微囊化大肠杆菌时, 反应溶液的最佳pH值为5.00; 制备微囊化酵母菌时, 反应溶液的最佳pH值为4.50.     

壳聚糖-丝心蛋白合金膜的研究(Ⅱ)──半互穿聚合物网络型膜对pH和离子的敏感性

研究了壳聚糖-丝心蛋白半互穿聚合物网络型膜对pH值和离子的敏感性,发现该膜在pH<3.3时溶胀度剧烈增加;在pH=2时,是否出现溶胀极大值与膜组分的含量及交联剂的含量有关;膜在不同pH值溶液中可交替溶胀和收缩,且这种溶胀-收缩行为重复可逆。同时,该膜在不同离子溶液中的溶胀度亦不同;在相同离子强度的溶液中,此膜在3价离子中的溶胀度最大。     

聚酰亚胺/SiO2杂化膜的制备、表征和气体渗透性能

采用溶胶凝胶法,在以TiO2为过渡层的硅藻土-莫来石陶瓷膜管基底上,制备了组分不同的聚酰亚胺/SiO2杂化膜。聚酰亚胺是利用4,4′-六氟亚异丙基邻苯二甲酸酐、2,4,6-三甲基-1,3-苯二胺和3,5-二氨基苯甲酸在溶液中进行亚胺化完成的。采用FT-IR、TG/DTA、DSC、SEM、BET和气体渗透测定对膜进行了表征和测试。结果表明,聚酰亚胺通过支链上的羧酸基和SiO2相键连织构成了具有规则孔道的空间网状结构,并且随着SiO2含量的增加孔径逐渐减小;杂化膜具有较高的热稳定性和有机无机兼容性;相对于聚酰亚胺膜,杂化膜对H2、CO2和H2O与N2相比较具有较高的分离性,SiO2含量为25(wt)%的杂化膜对H2/N2、CO2/N2和H2O/N2的分离因子分别达到55.9、31.1和42.8。     

F127反相微乳液的组成对AgCl纳米粒子形成及AgCl/F127-PMMA杂化膜结构和性能的影响

以F127为表面活性剂构成的反相微乳液制备AgCl纳米粒子和AgCl/F127-PMMA杂化膜,通过紫外可见光谱(UV-visible)、透射电镜(TEM)研究了微乳液的增容水量(ω)和盐浓度(Csalt)对AgCl粒子形成与形貌的影响;结合表面ζ电位测定、扫描电镜(SEM)分析和溶胀实验等考察了AgCl/F127-PMMA杂化膜的结构和性能。研究结果表明,低ω下盐浓度增加,胶束中AgCl反应速率增大,导致大量小粒径AgCl粒子的形成;高ω下盐浓度增加,将加快AgCl粒子的生长,从而导致胶束中的AgCl粒子粒径增大;各种ω下盐浓度的增加,都会引起胶束中单质Ag的形成。杂化膜的SEM分析显示,AgCl粒子粒径越小,在杂化膜中的分散性越好,膜表面的ζ电位也越高,膜在苯中的溶胀性能也越高;单质Ag的出现和AgCl粒子数目的增多,杂化膜中将显现明显的粒子团聚现象,这极大地影响了杂化膜在苯中的溶胀性能;而杂化膜在环己烷中的溶胀性能较低,且随ω和盐浓度的变化极小。     

壳聚糖功能化改性及其在药物载体中的应用

壳聚糖为天然多糖甲壳素脱除部分乙酰基的产物,因其优异的理化性质和生物学活性,成为生物医学应用中最有前景的聚合物之一。由于壳聚糖在中性和碱性溶液中溶解性较差,其应用受到了一定限制,通常对其进行功能化改性,生成一系列壳聚糖衍生物。壳聚糖衍生物可改善壳聚糖的水溶性、生物活力及力学性能,从而提高其利用价值,扩大其应用领域。本文综述了几种壳聚糖常用的功能化改性方法,包括接枝共聚、交联、羧甲基化、酰基化、烷基化。并介绍了改性壳聚糖作为药物载体应用的研究进展,旨在为改性壳聚糖的研究提供一定理论基础。     

壳聚糖纳米银溶液的稳定性及在织物抗菌整理上的应用

采用化学还原法在不同浓度的壳聚糖醋酸溶液中以硼氢化钠还原硝酸银, 制备了系列壳聚糖纳米银溶液; 考察了不同质量分数的壳聚糖溶液对纳米银的浓度、 形貌和粒径大小的影响及纳米银的稳定性. 采用紫外-可见吸收光谱、 原子吸收光谱和透射电子显微镜对所得溶液进行表征, 结果表明, 当有壳聚糖存在时, 纳米银以小于50 nm球形粒子稳定分布于壳聚糖溶液中. 随着壳聚糖质量分数的增大, 形成纳米银浓度减小, 但稳定性提高, 壳聚糖质量分数控制在0.5%~0.7%范围内, 可得到浓度较高且稳定性良好的纳米银. 在壳聚糖和纳米银的共同作用下织物具有极好的抗菌性和抗菌长效性.     

Polycaprolactone membranes reinforced by toughened sol–gel produced silica networks

The aim of this work is to develop polycaprolactone based porous materials with improved mechanical performance to be used in bone repair. The hybrid membranes consist in a polymeric porous material in which the pore walls are coated by a silica thin layer. Silica coating increases membrane stiffness with respect to pure polymer but in addition filling the pores of the polymer with a silica phase improves bioactivity due to the delivery of silica ions in the neighborhood of the material in vivo. Nevertheless silica network, even that produced by sol–gel, might be too stiff and brittle what is not desirable for its performance as a coating. In this work we produced a toughened silica coating adding chitosan and 3-glycidoxypropyltrimethoxysilane (GPTMS) to the precursor solution looking for having polymer chains linked by covalent bonding to the silica network. Hybrid polymer–silica coating was produced by in situ sol–gel reaction using Tetraethyl orthosilicate (TEOS), GPTMS and chitosan. Chemical reaction between amine groups of chitosan chains and epoxy groups of GPTMS allowed covalent bonding of polymer chains to the silica network. Physical properties of the hybrid membranes were characterized and cell attachment of MC3T3-E1 pre-osteoblastic cells on the surface of these supports was assessed.     

Pervaporation performance of novel chitosan‐POSS hybrid membranes: Effects of POSS and operating conditions

Four types of polyhedral oligosilsesquioxane (POSS)–octaanion, octaammonium, octanitrophenyl, and octaaminophenyl–were incorporated into chitosan (CS) to fabricate inorganic–organic hybrid membranes. The hybrid membranes were employed for the pervaporation dehydration of ethanol aqueous solutions. The performance of the hybrid membranes was found to be influenced by the type and loading amount of POSS. In comparison with the neat CS membranes which showed a separation factor of 65.2 for 10 wt % water in the feed at 303 K, the hybrid membranes containing 5 wt % of octaanion and octaaminophenyl POSS showed high separation factors of 305.6 and 373.3, respectively. The effects of the operating conditions such as the feed composition and temperature on the pervaporation performance of the membranes were investigated. Activation energies for permeation in the membranes were estimated from Arrhenius relationship. The activation energies for ethanol permeation in the hybrid membranes were much higher than that in the CS membrane, which may account for the large enhancements in the selectivity of the hybrid membranes. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Fabrication of superhydrophilic poly(styrene-alt-maleic anhydride)/silica hybrid surfaces on poly(vinylidene fluoride) membranes

Superhydrophilic organic/inorganic hybrid surfaces have been fabricated on blend membranes of poly(vinylidene fluoride) (PVDF) and poly(styrene-alt-maleic anhydride) (SMA). The blend membranes were prepared from PVDF/SMA mixed solution with N,N-dimethylacetamide (DMAc) as solvent by immersion-precipitation phase inversion process. The gained blend membranes were immersed into γ-aminopropyltriethoxysilane (APTS) solution to generate SMA/silica hybrid surfaces by the reaction between anhydrides and APTS. The hybrid surfaces chemical compositions, morphologies and hydrophilicity were investigated in detail. It demonstrates that the hybrid surfaces possess micro-nano hierarchical structure and display superhydrophilicity property and good stability. Finally, the reaction and formation mechanism of the superhydrophilicity hybrid surface was discussed.     

Crosslinked chitosan composite membrane for the pervaporation dehydration of alcohol mixtures and enhancement of structural stability of chitosan/polysulfone composite membranes

Chitosan composite membranes having a microporous polysulfone substrate were prepared and tested for the pervaporation dehydration of aqueous isopropanol mixtures. When the composite membrane experienced excessive swelling at the feed mixture of high water content, the composite membranes were found to be segregated in structure due to the opposite characteristics to water of chitosan and polysulfone. Efforts to enhance the structural stability under various pervaporation operational conditions were made. The polysulfone substrate was immersed into hydrophilic binding polymer solutions such as polyvinyl alcohol, polyacrylic acid, and hydroxyethylcellulose before the casting of chitosan layer to increase the affinity between the thin chitosan layer and porous polysulfone layer which resulted in increased geometrical stability of the chitosan/polysulfone composite membranes. The chitosan layer was crosslinked with glutaraldehyde and H₂SO₄ in acetone solution to control the permselectivity.     

Preparation of hybrid hydrogel containing ag nanoparticles by a green in situ reduction method

In this Article, large and uniform Ag nanoparticle-containing hybrid hydrogels were prepared by in situ reduction of Ag ions in cross-linked tapioca dialdehyde starch (DAS)-chitosan hydrogels. In the hybrid hydrogels, chitosan was chosen as a macromolecular cross-linker because of its abundant source and good biocompatibility. The hybrid hydrogel showed good water-swelling properties, which could be controlled by varying the ratio of chitosan to tapioca DAS in the hydrogel. The reductive aldehyde groups in the cross-linked hydrogels could be used to reduce Ag ions to Ag nanoparticles without any additional chemical reductants. Interestingly, by controlling the reduction conditions such as the tapioca DAS concentration, aqueous AgNO(3) concentration, reaction time, and aqueous ammonium concentration, Ag nanoparticles with different sizes and morphologies were obtained. Because of their biocompatibility, degradable constituents, mild reaction conditions, and controlled preparation of Ag nanoparticles, these tapioca DAS-chitosan/Ag nanoparticle hybrid hydrogels show promise as functional hydrogels.     

丙烯酸交联壳聚糖渗透汽化膜研究（Ⅰ）——膜结构及交联机理

报道了一种新型渗透汽化膜－－丙烯酸交联壳聚糖膜，通过溶胀、拉伸、渗透汽化分离以及红外光谱等手段研究了膜的结构和交联机理。实验结果表明，交联反应由两部分组成：丙烯酸的双键和壳聚糖的氨基的加成反应和丙烯酸另一端的羧基和壳聚糖的氨基的酸碱中和反应。     

Degradation mechanism and increased stability of chitosan-based hybrid scaffolds cross-linked with nanostructured carbon: Process–structure–functional property relationship

The degradation behavior of porous scaffolds plays an important role in the synthesis of new tissue. In this study, three-dimensional hybrid porous scaffolds of chitosan (CS) comprised of nanostructured carbon (graphene oxide (GO) and single-walled carbon nanohorns (SWCNH)) were prepared by freeze-drying method. In-vitro degradation behavior of scaffolds was investigated up to 8 weeks in phosphate buffer saline (PBS) solution at 37 °C. The characteristics of scaffolds explored as a function of degradation time include crystalline structure, pore morphology, molecular weight, and wet/dry weight. The pH value of the PBS solution during degradation was also monitored. The study demonstrates for the first time that hybrid chitosan scaffolds with nanostructured carbon (GO and SWCNH) are potentially more stable than pure chitosan scaffolds during the time period required for tissue regeneration. The stability of hybrid scaffolds is attributed to nanostructured carbon that was processed with the objective that it is present in a robust manner via a highly cross-linked dense network structure. The chemical structure of chitosan was disrupted within a short period of two weeks, while disruption occurred in hybrid scaffolds after eight weeks. This was accompanied by a weight loss of ∼28% in pure chitosan and ∼20% in hybrid scaffolds. Furthermore, the degraded products were of low molecular weight in pure chitosan and high molecular weight in hybrid chitosan scaffolds. This led to significant decrease in the pH of solution to ∼6.2 in pure chitosan and to ∼7.2 in hybrid scaffolds. The observations clearly underscore that the introduction of GO and SWCNH via cross-link mechanism in CS is a potentially viable approach to tune the degradation rate of hybrid scaffolds in tissue engineering.     

Difference in transfer of magnesium and sodium ions through electrodialytic membranes modified with chitosan

The difference in transfer of magnesium and sodium ions through electrodialytic cation-exchange membranes modified with chitosan was studied. The membranes were modified by electrodeposition of chitosan from solution on the membrane surface in the course of electrodialysis, preliminary sorption of chitosan on the membrane surface from aqueous chitosan hydrochloride, or application of a chitosan film to the dry membrane surface. The Mg²⁺/Na⁺ selectivity of transfer through modified electrodialytic membranes was examined in relation to the current density.     

Novel nylon-supported organic-inorganic hybrid membrane with hierarchical pores as a potential immobilized metal affinity adsorbent

Chitosan-based porous organic-inorganic hybrid membranes supported by microfiltration nylon membranes were prepared, in which gamma-glycidoxypropyltrimethoxysilane (GPTMS) was used as an inorganic source as well as crosslinking reagent. Polyethylene glycol (PEG) with different molecular weight and content was used as imprinting molecule for morphology control. In situ crosslinking of chitosan and simultaneous polymerization of GPTMS in PEG template environment endowed the hybrid membrane with specific characteristics. Distinct hybrid effect between chitosan (CS) and GPTMS was revealed by shifting in X-ray diffraction (XRD) pattern, decomposition in simultaneous thermogravimetry and differential scanning calorimetry (TG/DSC) testing. As manifested by scanning electron microscopy (SEM), the molecular weight and content of PEG had remarkable effect on the resulting surface morphology of the hybrid membrane and a given surface morphology could be obtained by extracting of the imprinted PEG molecular. Among three types of porogen used: PEG 400, PEG 4000 and PEG 20000, only PEG 20000 could result in a porous surface. Moreover, a special porous surface with three-dimensional (3D) hierarchical structure-in-structure pore fashion was obtained when content of PEG 20000 was controlled at 15%. Experimental results also showed that the hybrid membrane had low swelling ratio and high stability in acidic solution. After conveniently coordinated with copper ions, the porous metal chelating hybrid membrane could effectively adsorb the model protein, bovine serum albumin (BSA). As expected, the hybrid membrane imprinted with 15% PEG 20000 had remarkably high copper ion binding and BSA adsorption capacity, which might result from the large surface area, high ligand density and suitable interconnected 3D hierarchical porous surface.     

Preparation and Characterization of Chitosan Composite Membranes Crosslinked by Carboxyl-capped Poly（ethylene glycol）

In this study a series of chemically crosslinked chitosan/poly（ethylene glycol） （CS/PEG） composite membranes were prepared with PEG as a crosslinking reagent other than an additional blend. First, carboxyl-eapped poly（ethylene glycol） （HOOC-PEG-COOH） was synthesized. Dense CS/PEG composite membranes were then prepared by casting/evaporation of CS and HOOC-PEG-COOH mixture in acetic acid solution. Chitosan was chemically crosslinked due to the amidation between the carboxyl in HOOC-PEG-COOH and the amino in chitosan under heating, as confirmed by FTIR analysis. The hydrophilicity, water-resistance and mechanical properties of pure and crosslinked chitosan membranes were characterized, respectively. The results of water contact angle and water absorption showed that the hydrophilicity of chitosan membranes could be significantly improved, while no significant difference of weight loss between pure chitosan membranes and crosslinked ones was detected, indicating that composite membranes with amidation crosslinking possess excellent water resistanance ability. Moreover, the tensile strength of chitosan membranes could be significantly enhanced with the addition of certain amount of HOOC-PEG-COOH crosslinker, while the elongation at break didn＇t degrade at the same time. Additionally, the results of swelling behaviors in water at different pH suggested that the composite membranes were pH sensitive.