Influence of mesoporosity on the sorption of 2,4-dichlorophenoxyacetic acid onto alumina and silica

Two SiO2 and three Al2O3 adsorbents with varying degrees of mesoporosity (pore diameter 2-50 nm) were reacted with 2,4-dichlorophenoxyacetic acid (2,4-D) at pH 6 to investigate the effects of intraparticle mesopores on adsorption/desorption. Anionic 2,4-D did not adsorb onto either SiO2 solid, presumably because of electrostatic repulsion, but it did adsorb onto positively charged Al2O3 adsorbents, resulting in concave isotherms. The Al2O3 adsorbent of highest mesoporosity consistently adsorbed more 2,4-D per unit surface area than did the nonporous and less mesoporous Al2O3 adsorbents over a range of initial 2,4-D solution concentrations (0.025-2.5 mM) and reaction times (30 min-55 d). Differences in adsorption efficiency were observed despite equivalent surface site densities on the three Al2O3 adsorbents. Hysteresis between the adsorption/desorption isotherms was not observed, indicating that adsorption is reversible. Attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy studies confirm that 2,4-D adsorption does not occur via ligand exchange, but rather via electrostatic interaction. The results indicate that adsorbent intraparticle mesopores can result in consistently greater 2,4-D adsorption, but the amount adsorbed is dependent upon surface charge and the presence of adsorbent mesoporosity. The data also suggest that when mineral pores are significantly larger than the adsorbate, they do not contribute to diffusion-limited adsorption/desorption hysteresis. Adsorbent transformations through time are discussed.     

表面活性剂和聚乙烯吡咯烷酮在ZrO2上的吸附对其悬浮体稳定性的影响

研究了水溶液中十二烷基苯磺酸钠（ＳＤＢＳ）、溴代十四烷基吡啶（ＴＰＢ）和聚乙烯吡咯烷酮（ＰＶＰ）在ＺｒＯ２上的吸附及对ＺｒＯ２水悬浮体稳定性的影响。结果表明：ｐＨ＝２．４时ＳＤＢＳ在ＺｒＯ２上的吸附等湿线为ＬＳ型，ｐＨ＝７．０时ＴＰＢ的吸附等温线为Ｓ型，吸附等温线与ＺｒＯ２粒子ζ电势变化同线有大体一致的关系。在最大吸附量时ＺｒＯ２粒子ζ电势较大，且吸附的表面活性剂离子形成大部分亲水基朝向水相的表面     

Grand canonical Monte Carlo simulation of the adsorption isotherms of water molecules on model soot particles

The grand canonical Monte Carlo method is used to simulate the adsorption isotherms of water molecules on different types of model soot particles. The soot particles are modeled by graphite-type layers arranged in an onionlike structure that contains randomly distributed hydrophilic sites, such as OH and COOH groups. The calculated water adsorption isotherm at 298 K exhibits different characteristic shapes depending both on the type and the location of the hydrophilic sites and also on the size of the pores inside the soot particle. The different shapes of the adsorption isotherms result from different ways of water aggregation in or/and around the soot particle. The present results show the very weak influence of the OH sites on the water adsorption process when compared to the COOH sites. The results of these simulations can help in interpreting the experimental isotherms of water adsorbed on aircraft soot.     

Comparison of Solvent Adsorption on Chemically Bonded Stationary Phases in RP-LC

The excess adsorption isotherms of organic modifiers (methanol and acetonitrile) from water on chemically bonded stationary phases were studied, using seven different packed columns with different organic ligand lengths from C4 to C30. Isotherms were measured using the minor disturbance method. Excess isotherms can give useful information about the structure of the stationary phase. The amount of “adsorbed” solvent can indicate the type of distribution mechanism.     

Application of water-activated carbon isotherm models to water adsorption isotherms of single-walled carbon nanotubes

The objective of this study is to understand the interactions of water with novel nanocarbons by implementing semiempirical models that were developed to interpret adsorption isotherms of water in common carbonaceous adsorbents. Water adsorption isotherms were gravimetrically determined on several single-walled carbon nanotube (SWNT) and activated carbon samples. Each isotherm was fitted to the Dubinin-Serpinsky (DS) equation, the Dubinin-Astakov equation, the cooperative multimolecular sorption theory, and the Do and Do equations. The applicability of these models was evaluated by high correlation coefficients and the significance of fitting parameters, especially those that delineate the concentration of hydrophilic functional groups, micropore volume, and the size of water clusters. Samples were also characterized by spectroscopic and adsorption techniques, and properties complementary to those quantified by the fitting parameters were extracted from the data collected. The comparison of fitting parameters with sample characterization results was used as the methodology for selecting the most informative and the best-fitting model. We conclude that the Do equation, as modified by Marban et al., is the most suitable semiempirical equation for predicting from experimental isotherms alone the size of molecular clusters that facilitate adsorption in SWNTs, deconvoluting the experimental isotherms into two subisotherms: adsorption onto hydrophilic groups and filling of micropores, and quantifying the concentration of hydrophilic functional groups, as well as determining the micropore volume explored by water. With the exception of the DS equation, the application of other water isotherm models to SWNTs is not computationally tractable. The findings from this research should aid studies of water adsorption in SWNTs by molecular simulation, which remains the most popular tool for understanding the microscopic behavior of water in nanocarbons.     

高分子表面活性剂在固/液界面上的吸附形态

采用紫外光谱、XPS研究了羧甲基纤维素型高分子表面活性剂在硅胶 /水界面上的吸附形态 ,结果表明随着高分子表面活性剂溶液浓度增大 ,分子在硅胶表面的吸附由单层逐渐变为多层 ,生成半胶束结构 .     

Removal of 2,4-dichlorophenoxyacetic acid from aqueous solutions by partially characterized organophilic sepiolite: thermodynamic and kinetic calculations

The adsorption of 2,4-dichlorophenoxyacetic acid (2,4-D) on organophilic sepiolite (dodecylammonium sepiolite, DAS) was studied as a function of solution concentration and temperature. The observed adsorption rates were found to be equal to the first-order kinetics. The rate constants were calculated for temperatures ranging between 25 and 40 degrees C at constant concentration. The adsorption energies, E, and adsorption capacity, q(m), for 2,4-D adsorption on organophilic sepiolite was estimated using the Dubinin-Radushkevic equation. Thermodynamic parameters (Deltag(a), Deltah(a), Deltas(a)) were determined by a new approximation from the isotherm of 2,4-D adsorption on DAS. Also, DeltaS(0) and DeltaH(0) values were calculated from the van't Hoff equation. These isotherms were modeled according to the Freundlich and Dubinin-Radushkevic adsorption equations. The amount of adsorption of this herbicide on organophilic sepiolite was found to be dependent on the relative energies of adsorbent-adsorbate, adsorbate-solvent, and adsorbate-adsorbate interaction.     

Effect of water on the retention on diol and amide columns in hydrophilic interaction liquid chromatography

The amount of water adsorbed on polar columns plays important role in hydrophilic interaction liquid chromatography. It may strongly differ for the individual types of polar columns used in this separation mode. We measured adsorption isotherms of water on an amide and three diol‐bonded stationary phases that differ in the chemistry of the bonded ligands and properties of the silica gel support. We studied the effects of the adsorbed water on the retention of aromatic carboxylic acids, flavonoids, benzoic acid derivatives, nucleic bases, and nucleosides in aqueous‐acetonitrile mobile phases over the full composition range. The graphs of the retention factors versus the volume fraction of water in mobile phase show “U‐profile” characteristic of a dual hydrophilic interaction–reversed phase retention mechanism. The minimum on the graph that marks the changing retention mechanism depends on the amount of adsorbed water. The linear solvation energy relationship model suggests that the retention in the hydrophilic interaction liquid chromatography mode is controlled mainly by proton–donor interactions in the stationary phase, depending on the column type. Finally, the accuracy of hydrophilic interaction liquid chromatography gradient prediction improves for columns that show a high water adsorption.     

Adsorption of nitrobenzene andn-pentanol from aqueous solution on hydrophilic and hydrophobic clay minerals

The sorption of nitrobenzene andn-pentanol from dilute aqueous solution on swelling clay minerals and their organophilized derivatives (organo clays) was studied. Adsorption excess isotherms were obtained by the immersion method. The basal spacings of the clay minerals were determined by X-ray diffraction measurements. By combining these two independent methods, composition and structure of the interlamellar space could be calculated. On the hydrophilic surface of montmorillonite negative adsorption of the organic component was observed at low molar fractions of nitrobenzene or pentanol, i.e., water was preferentially adsorbed. On organophilized montmorillonite and vermiculite adsorption of nitrobenzene and pentanol was positive over the whole range of liquid composition. The amount of interlamellar alkyl chains which is determined by the surface charge of clay mineral inversely affected the adsorption of both solutes.     

Adsorption of water and ethanol in MFI-type zeolites

Water and ethanol vapor adsorption phenomena are investigated systematically on a series of MFI-type zeolites: silicalite-1 samples synthesized via both alkaline (OH(-)) and fluoride (F(-)) routes, and ZSM-5 samples with different Si/Al ratios as well as different charge-balancing cations. Full isotherms (0.05-0.95 activity) over the range 25-55 °C are presented, and the lowest total water uptake ever reported in the literature is shown for silicalite-1 made via a fluoride-mediated route wherein internal silanol defects are significantly reduced. At a water activity level of 0.95 (35 °C), the total water uptake by silicalite-1 (F(-)) was found to be 0.263 mmol/g, which was only 12.6%, 9.8%, and 3.3% of the capacity for silicalite-1 (OH(-)), H-ZSM-5 (Si/Al:140), and H-ZSM-5 (Si/Al:15), respectively, under the same conditions. While water adsorption shows distinct isotherms for different MFI-type zeolites due to the difference in the concentration, distribution, and types of hydrophilic sites, the ethanol adsorption isotherms present relatively comparable results because of the overall organophilic nature of the zeolite framework. Due to the dramatic differences in the sorption behavior with the different sorbate-sorbent pairs, different models are applied to correlate and analyze the sorption isotherms. An adsorption potential theory was used to fit the water adsorption isotherms on all MFI-type zeolite adsorbents studied. The Langmuir model and Sircar's model are applied to describe ethanol adsorption on silicalite-1 and ZSM-5 samples, respectively. An ideal ethanol/water adsorption selectivity (α) was estimated for the fluoride-mediated silicalite-1. At 35 °C, α was estimated to be 36 for a 5 mol % ethanol solution in water increasing to 53 at an ethanol concentration of 1 mol %. The adsorption data demonstrate that silicalite-1 made via the fluoride-mediated route is a promising candidate for ethanol extraction from dilute ethanol-water solutions.     

Adsorption equilibria of proline in hydrophilic interaction chromatography

The adsorption behavior of proline under hydrophilic interaction chromatography conditions was investigated from six aqueous solutions of acetonitrile. Proline adsorption isotherms were recorded at each mobile phase composition by frontal analysis and inverse method. The BET model was found to be the best choice to describe the nonlinear behavior of proline adsorption under hydrophilic interaction chromatography conditions. The adsorption isotherm parameters were derived from two independent parameter estimation methods. The parameters derived from regression analysis of the frontal analysis data and from overloaded elution bands were found to be in good agreement with the excess isotherm of water. The mobile phase composition at which the maximum excess adsorption of water was observed corresponded to the maximum saturation capacity measured for proline.     

Adsorption and activity of Thermomyces lanuginosus lipase on hydrophobic and hydrophilic surfaces measured with dual polarization interferometry (DPI) and confocal microscopy

The adsorption and activity of Thermomyces lanuginosus lipase (TLL) was measured with dual polarization interferometry (DPI) and confocal microscopy at a hydrophilic and hydrophobic surface. In the adsorption isotherms, it was evident that TLL both had higher affinity for the hydrophobic surface and adsorbed to a higher adsorbed amount (1.90 mg/m²) compared to the hydrophilic surface (1.40–1.50 mg/m²). The thickness of the adsorbed layer was constant (3.5 nm) on both surfaces at an adsorbed amount >1.0 mg/m², but decreased on the hydrophilic surface at lower surface coverage, which might be explained by partially unfolding of the TLL structure. However, a linear dependence of the refractive index of the adsorbed layer on adsorbed amount of TLL on C18 surfaces indicated that the structure of TLL was similar at low and high surface coverage. The activity of adsorbed TLL was measured towards carboxyfluorescein diacetate (CFDA) in solution, which upon lipase activity formed a fluorescent product. The surface fluorescence intensity increase was measured in a confocal microscope as a function of time after lipase adsorption. It was evident that TLL was more active on the hydrophilic surface, which suggested that a larger fraction of adsorbed TLL molecules were oriented with the active site facing the solution compared to the hydrophobic surface. Moreover, most of the activity remained when the TLL surface coverage decreased. Earlier reports on TLL surface mobility on the same surfaces have found that the lateral diffusion was highest on hydrophilic surfaces and at low surface coverage of TLL. Hence, a high lateral mobility might lead to a longer exposure time of the active site towards solution, thereby increasing the activity against a water-soluble substrate.     

Synthesis and Characterization of Microporous Silica Prepared with Sodium Silicate and Organosilane Compounds

Microporous silica gels were prepared in the pH range of 3–4 using sodium silicate as a silica source. Surface polarity of these gels was modified by grafting hydrophobic groups into the silica gel matrix with the help of hydrophilic solvents (acetone, acetonitrile, ethanol and methanol) and alkoxysilane compounds containing nonhydrolyzable alkyl groups. The porous framework and hydrophobicity of the silica gels were evaluated using nitrogen adsorption/desorption and water adsorption measurement techniques. All the measured isotherms were found to be type I which is indicative of microporosity. The surface area and microporosity of these samples were estimated by analyzing the measured nitrogen adsorption/desorption data using BET, Langmuir and Dubinin-Radushkevich (D-R) adsorption isotherms. The micropore size distribution was determined from their nitrogen adsorption isotherms using the slit-pore model of the Horvath-Kawazoe equation. Silica gels with high surface area (over 500 m²/g) as well as high microporosity (over 0.2 cc/g) were obtained at gelation pH of 3.50 from the water-solvent system.     

Interaction between silica nanoparticles in binary liquid mixtures: the effect of polarity on adhesion

In order to explore the relationship between selective liquid sorption and the stability of dispersed silica particles, we carried out studies in ethanol–cyclohexane binary mixtures as well as in partially miscible 1-butanol–water mixtures. In ethanol–cyclohexane, adsorption excess isotherms were determined on hydrophilic and hydrophobic aerosil particles. The volume and the thickness of the adsorption layer were derived from the isotherms. Knowing the layer thickness and Hamaker constants, interparticle interaction potentials were calculated at various mixture compositions. At low ethanol concentration, where hydrophilic surfaces are considerably enriched in ethanol, interparticle interaction is enhanced and the high shear stress calculated from rheological measurements indicates the development of a three-dimensional network of aggregated particles. In contrast, hydrophobic aerosil particles in ethanol–cyclohexane approach each other without ensuing aggregation because interparticle interactions are weak, a fact well demonstrated by rheological measurements. It was also established that interactions between silica particles with hydrophilic surfaces are weak in butanol–water mixtures. Since water is preferentially adsorbed on the surface of hydrophilic particles to the azeotropic composition (\( x_{\rm{1}}^{\rm{a}} \)=0.62), within this wide composition range the Hamaker constant of the interfacial layer is identical with that of water.     

Adsorption behavior of cationic polymers on bentonite

The adsorption behavior of a series of cationic water-soluble polymers poly(diallyldimethylammonium chloride) with different molar masses onto raw bentonite was investigated through the elaboration of their adsorption isotherms and the quantification of the water content of the clay/polymer complexes formed. It was found that the type of adsorption isotherms obtained depends on the chain length of the polymer. The study showed a correlation between the amount of adsorbed polymer and the water content of the clay, after the adsorption experiments. The lower the molar mass of the polymer used, the larger was the reduction on water content of the complexes.     

Cluster-Mediated Water Adsorption on Carbon Nanopores

The adsorption isotherms of water at 303 K and N2 at 77 K on various kinds of porous carbons were compared with each other. The saturated amounts of water adsorbed on carbons almost coincided with amounts of N2 adsorption in micropores. Although carbon aerogel samples have mesopores of the great pore volume, the saturated amount of adsorbed water was close to the micropore volume which is much small than the mesopore volume. These adsorption data on carbon aerogels indicated that the water molecules are not adsorbed in mesopores, but in micropores only. The adsorption isotherms of water on activated carbon having micropores of smaller than 0.7 nm in width had no clear adsorption hysteresis, while the water adsorption isotherms on micropores of greater than 0.7 nm had a remarkable adsorption hysteresis above P/P0 = 0.5. The disappearance of the clear hysteresis for smaller micropores suggested that the cluster of water molecules of about 0.7 nm in size gives rise to the water adsorption on the hydrophobic micropores; the formation and the structure of clusters of water molecules were associated with the adsorption mechanism. The cluster-mediated pore filling mechanism was proposed with a special relevance to the evidence on the formation of the ordered water molecular assembly in the carbon micropores by in situ X-ray diffraction.     

Adsorption of benzoic acid from organic solvents on calcite and dolomite: Influence of water

A study has been carried out of the adsorption of benzoic acid from cyclohexane solution onto the hydrophilic surface of calcite.

We determined initially the chemical and mineral composition of the solid, its specific surface area and its granulometry. This was followed by the determination of the enthalpies of immersion of calcite in different solvents. These thermodynamic properties gave information on the energetics of calcite—solvent interactions. In this way, we could construct a scale of affinities of the different organic molecules and water for the calcite surface. It was noted that the enthalpies were higher in unsaturated than in saturated organic solvents, and higher in water than in the organic solvents.

The adsorption isotherms and the differential molar enthalpies of displacement were determined in the presence and the absence of water. The role played by water in the adsorption of polar organic molecules from the oil phase has not been clearly explained previously. In this paper, we indicate how the presence of water can modify the adsorption of aromatic compounds on the surface of calcite. As regards the adsorption isotherms, the presence of water essentially increases the amount of adsorption. The results of the calorimetric studies were found to be surprising; we observed that the differential molar enthalpies of displacement were endothermic.

Similar experiments were carried out with dolomite and n-heptane solution and the results compared with those obtained with calcite and cyclohexane, leading to the formulation of a general model concerning the adsorption of small polar organic molecules from organic solvents onto the surfaces of the carbonates.     

Assessment of the Surface Heterogeneity of Talc Materials

The hydrophobic and hydrophilic components of the surface of talc materials in aqueous solution were determined using ionic surfactants and their polar headgroup adsorption isotherms. The hydrophilic and hydrophobic surface areas are inferred from the amount of probe molecule adsorbed and the structure of the adsorbed layer. Natural dispersion of talc shows at 298 K a pH of 9.4 and the electrophoretic measurements indicate that the particles are negatively charged. The hydrophilic surface area is estimated from the adsorption of benzyltrimethylammonium ions (BTMA(+)) through electrostatic interactions as supported by the increase of divalent ions in the bulk phase and the decrease in the exothermic displacement enthalpy. It was also observed from the adsorption isotherm of benzene sulfonate anions that the density of positive surface sites is very low and is thus neglected. The adsorption of an anionic surfactant essentially occurs through dispersive interactions between the nonpolar organic tail of the molecule and the hydrophobic surface. Furthermore, some assumptions on the structure of dodecyl sulfate surfactant aggregates at the interface allow the hydrophobic part of the talc particles to be estimated. The cationic surfactant adsorption has been investigated and found to corroborate the hydrophilic and hydrophobic area values first obtained. Copyright 2001 Academic Press.     

CMC型高分子表面活性剂在固/液界面上的吸附

在润湿、乳化、洗涤、分散等应用领域中,表面活性剂分子在界面上的吸附状态对性能有重要影响.另一方面,在化学驱油过程中,表面活性剂分子在氧化物矿物上的吸附是引起表面活性剂损失的主要原因,表面活性剂的损耗量大,将降低采收率及经济效益[1].高分子表面活性剂作为一种多功能的新型表面活性剂在许多领域有广阔的应用前景,但对其性能研究尚处于起步阶段,特别是结构复杂的高分子双亲性共聚物,在吸附、乳化等方面研究尚少报导.羧甲基纤维素系列高分子表面活性剂是采用独特的超声波辐照技术合成的嵌段型共聚物,具有优良的表/界面活性[2],可望用…     

疏水/亲水大孔聚二乙烯基苯/聚(N-2-氨基乙基丙烯酰胺)IPN树脂的合成及对水杨酸吸附性能研究

采用分步悬浮聚合法制备了聚二乙烯基苯/聚丙烯酸甲酯(PDVB/PMA)大孔互穿聚合物网络,将其中的聚丙烯酸甲酯用乙二胺氨解,合成了具有疏水/亲水性能的聚二乙烯基苯/聚(N-2-氨基乙基丙烯酰胺)(PDVB/PNAEAM)大孔互穿聚合物网络(IPN);测定了该树脂的孔结构、含水量、弱碱交换量和溶胀性能;测定了该树脂对水杨酸在不同温度下的吸附等温线,利用热力学函数关系计算出了吸附焓、自由能和熵.推测PDVB/PNAEAM IPN树脂中疏水性的PDVB一网具有疏水作用吸附能力、亲水性的PNAEAM一网具有氢键作用吸附能力.动态吸附及脱附实验表明湿态PDVB/PNAEAM IPN树脂对水溶液中水杨酸的饱和吸附量达到46.1mg/mL.树脂可以通过4%NaOH溶液再生.PDVB/PNAEAM IPN树脂在分离工业废水中水杨酸等芳香有机酸有良好的应用前景.