Functionalization of organic membranes by polyelectrolyte multilayer assemblies: application to the removal of copper ions from aqueous solutions

The functionalization of an organic polyethersulfone membrane (PES) was performed by alternating deposition of poly(allylamine hydrochloride) (PAH) and poly(sodium 4-styrene sulfonate) (PSS), leading to the formation of a polyelectrolyte multilayer film (PEM). The resulting assembly was characterized by tangential streaming potential measurements to determine the charge of the modified membranes as a function of the polyelectrolyte solution concentration and as a function of the immersion time of the membrane in the polyelectrolyte solutions. Then, the modified membranes were used to perform the ultrafiltration of aqueous solutions containing copper(II) ions. Different operating conditions were tested including: polyelectrolyte concentration, polyelectrolyte nature, thickness of the PEM film or pH of the Cu(2+) solutions. These filtration experiments demonstrated that it was possible to obtain a satisfactory retention of the copper ions (88%), thus proving that this type of assembly can be useful for the removal of copper ions from contaminated aqueous solutions.     

Surface patterns induced by Cu2+ ions on BPEI/PAA layer-by-layer assembly

The multilayer films of branched polyethyleneimine (BPEI) and poly(acrylic acid) (PAA) have been fabricated with the layer-by-layer (LbL) method. Two characteristic courses of the film thickness growth are observed, which are the initial exponential-like growth and the following linear growth. The variation of the COOH/COO- ratio indicates that the ionization degree of the polyelectrolyte molecules decreases at the initial stage of the multilayer buildup and then levels off after about eight bilayers. The as-prepared (BPEI/PAA)n films show a relatively smooth surface. However, great morphology changes occur after immersing these films in Cu2+ or Zn2+ solution. In the case of n > or =7, wavelike surface patterns are induced to form on the films. Both wavelength and fluctuation of these surface patterns show a systematical variation with an increase of the bilayer number. Moreover, thermal treatment can stabilize these patterns and enable the preservation of them after releasing the Cu2+ ions from the LbL films by acidic treatment. Interestingly, only Cu2+ and Zn2+ can induce the formation of such surface patterns, whereas Fe2+, Ca2+, Ag+, and Na+ cannot. This phenomenon may closely relate to the different natures of the metal ions.     

Study of metal ion labeling of the conformational and charge states of lysozyme by ion mobility mass spectrometry

The efficiency of Zn(2+), Cu(2+), Ni(2+), Co(2+), Fe(2+) or Mn(2+) labeling of the conformational and charge states of lysozyme was studied in H(2)O solvent at pH 2.5-6.8. Labeling of lysozyme was conducted with 50 M, 100 M and 500 M excess of the metal ion, resulting in the number of metal ions attached to lysozyme increasing two-fold over this range. At pH 6.2-6.8, Zn(2+), Cu(2+), Ni(2+), Co(2+) and Mn(2+) labeled the highly folded 7+ conformer and the 8+ and 9+ partially unfolded conformers of lysozyme with the same number of metal ion tags, with only Fe(2+) exhibiting no labeling. Lysozyme conserved its charge after metal ion labeling which shows at each charge state the divalent metal ion is replacing two protons. As the pH is lowered to 4.7-5.0 and 2.5-2.9, the labeling of lysozyme by Zn(2+), Cu(2+), Ni(2+), Co(2+) or Mn(2+) decreased in efficiency due to increased competition from protons for the aspartate and glutamate binding sites. The metal ions preferentially labeled the highly folded 7+ and partially unfolded 8+ conformers, but labeling decreased as the charge of lysozyme increased. In contrast to the other metal ions, Fe(2+) exhibited labeling of lysozyme only at the lowest pH of 2.8. At higher pH, the oxidation of Fe(2+) and formation of hydroxy-bridged complexes probably make the Fe(2+) unreactive towards lysozyme.     

Fibronectin adsorption onto polyelectrolyte multilayer films

The Layer-by-layer deposition of positively and negatively charged macromolecular species is an ideal method for constructing thin films incorporating biological molecules. We investigate the adsorption of fibronectin onto polyelectrolyte multilayer (PEM) films using optical waveguide lightmode spectroscopy (OWLS) and atomic force microscopy (AFM). PEM films are formed by adsorption onto Si(Ti)O2 from alternately introduced flowing solutions of anionic poly(sodium 4-styrenesulfonate) (PSS) and cationic poly(allylamine hydrochloride) (PAH). Using OWLS, we find the initial rate and overall extent offibronectin adsorption to be greatest on PEM films terminated with a PAH layer. The polarizability density of the adsorbed protein layer, as measured by its refractive index, is virtually identical on both PAH- and PSS-terminated films; the higher adsorbed density on the PAH-terminated film is due to an adsorbed layer of roughly twice the thickness. The binding of monoclonal antibodies specific to the protein's cell binding site is considerably enhanced to fibronectin adsorbed to the PSS layer, indicating a more accessible adsorbed layer. With increased salt concentration, we find thicker PEM films but considerably thinner adsorbed fibronectin layers, owing to increased electrostatic screening. Using AFM, we find adsorbed fibronectin layers to contain clusters; these are more numerous and symmetric on the PSS-terminated film. By considering the electrostatic binding of a segmental model fibronectin molecule, we propose a picture of fibronectin adsorbed primarily in an end-on-oriented monolayer on a PAH-terminated film and as clusters plus side-on-oriented isolated molecules onto a PSS-terminated film.     

Swelling and contraction of ferrocyanide-containing polyelectrolyte multilayers upon application of an electric potential

We developed a new platform at the interface of polyelectrolyte multilayers (PEMs) and electroactive polymers (EAPs) by combining the easy buildup of PEM thin films and the deformation characteristics of the EAPs. The PEM films were made of poly(L-glutamic acid) (PGA) and poly(allylamine hydrochloride) (PAH). After [Fe(CN)6]4- ions (FCIV) were added, cyclic voltammetry (CV) was performed, resulting in a reversible expansion and contraction of the film. The shape change as well as the film buildup prior to the cycling were monitored in situ using the electrochemical quartz crystal microbalance with dissipation monitoring (EC-QCM-D). Electrochemical atomic force microscopy (EC-AFM) images confirmed the rapid shape deformation. The process takes place in an aqueous environment under mild conditions (maximum potential of 600 mV and no pH change), which makes it a promising tool for biomedical applications. In addition, the electrochemically active films are produced using the layer-by-layer (LbL) method that is already established in biotechnology and biomaterials science; therefore, the presented approach can be readily adapted in these areas, bringing about a new possibility for the nanoscale dynamic control of coating thickness in various applications.     

Modulation of the functions of osteoblast-like cells on poly(allylamine hydrochloride) and poly(acrylic acid) multilayer films

Deposition of layer-by-layer polyelectrolyte multilayer (PEM) films has been a widely applied surface modification technique to improve the biocompatibility of biomaterials. The objective of this study was to investigate the impact of the deposition of poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) multilayer films on adhesion, growth and differentiation of osteoblasts-like MG63 cells. PAH and PAA were deposited sequentially onto tissue culture polystyrene at either pH 2.0 or pH 6.5 with 4-21 layers. While the MG63 cells attached poorly on the PAH/PAA multilayer films deposited at pH 2.0, while the cells adhered to the PEM films deposited at pH 6.5, depending on layer numbers. Cell adhesion, proliferation and osteogenic activities (alkaline phosphatase activity, expression of osteogenic marker genes and mineralization) were highest on the 4-layer PAH/PAA film and decreased with increasing layer numbers. On the other hand, the behavior of MG63 cells did not show any difference on the adjacent even and odd layers, except PEM4 and PEM5, i.e. the surface charges of the PAH/PAA multilayer films with over ten layers seem indifferent to osteoblastic functions. The results in this study suggested that the mechanical properties of PEM films may play a critical role in modulating the behavior of osteoblasts, providing guidance for application of PEM films to osteopaedic implants.     

Immobilized metal ion affinity chromatography of synthetic peptides. Binding via the alpha-amino group.

Peptides synthesized by the solid-phase method can be efficiently purified in a single immobilized metal affinity chromatography step based on interaction with the alpha-amino group if, after coupling of each amino acid residue, unreacted amino groups are irreversibly blocked by acetylation and if no strongly metal-binding amino acids (His, Trp, Cys) are present in the sequence. A difference in basicity for alpha- and epsilon-amino functions of ca. 2 pH units is sufficiently large to allow selective binding of peptides to immobilized metal ions via the unprotonated alpha-amino group. The binding is pH-dependent: on Cu(2+)- and Ni(2+)-loaded supports most peptides are maximally retarded at pH values around 7.5 and 8.5, respectively. The decreased binding strength at lower pH values is due to protonation of the alpha-amino function, whereas the reduced affinity at higher pH is caused by metal ion transfer from the matrix to the peptide. The metal ion is captured in a multidentate chelate where, in addition to the alpha-amino group, up to three adjacent deprotonated amide nitrogens are coordinated to the metal. If the pH is raised further, additional metal ions may be bound in biuret-like structures. Immobilized Ni2+, owing to its higher selectivity and affinity, is the preferred chromatographic support if slightly basic conditions can be tolerated.     

Metal ion modulated organization and function of the Langmuir-Blodgett films of amphiphilic diacetylene: photopolymerization, thermochromism, and supramolecular chirality

Some novel properties of organized molecular films of 10,12-tricosadiynoic acid (TDA), which were modulated by transition metal ions, were investigated. It was found that metal ions such as Cu(2+), Zn(2+), Ni(2+), Cd(2+), and Ag(+) in the subphase can greatly affect the monolayer formation of TDA and the properties of the subsequently deposited Langmuir-Blodgett (LB) films, particularly in the case of Ag(+), Zn(2+), and Cu(2+) ions. TDA LB film from the subphase containing Ag(+) ion could not be photopolymerized. It was suggested that both the strong chelating property to the carboxylate and the easy reduction of Ag(+) in the film disrupted the topochemical sequence of TDA and resulted in no polymerization in the film. Zinc ion coordinated TDA film could be photopolymerized into a blue polydiacetylene (PDA) film, which showed a reversible thermochromism between blue and purple color upon thermal stimulation. Fourier transform infrared spectra revealed the difference of the Zn(2+)-PDA film from those of the other ions, and the mechanism of the thermochromism was discussed. Copper ion coordinated TDA film could only be photopolymerized to a red PDA film, which showed supramolecular chirality although TDA itself was achiral. Atomic force microscopic measurements revealed the nanofiber structure in the Cu(2+)-PDA film. The supramolecular chirality of the Cu(2+)-PDA film was suggested to be due to the arrangement of the polymer backbone in a helical sense. Furthermore, it was found that the chiral assemblies from the achiral TDA molecules were very stable and the chirality could be kept even upon heating or treating with alkaline solution. While many synthetic efforts have been devoted to the functionalization of PDA films, we provided a simple method of modulating the organization and function of PDA films through metal ions.     

Characteristics of polyelectrolyte multilayers: effect of PEI anchoring layer and posttreatment after deposition

The influence of a first (anchoring) layer and film treatment on the structure and properties of polyelectrolyte multilayer (PEM) films obtained from polyallylamine hydrochloride (PAH) and polysodium 4-styrenesulfonate (PSS) was studied. Branched polyethyleneimine (PEI) was used as an anchoring layer. The film thickness was measured by ellipsometry. Complementary X-ray reflectometry and AFM experiments were performed to study the change in the interfacial roughness. We found that the thickness of the PEM films increased linearly with the number of layers and depended on the presence of an anchoring PEI layer. Thicker films were obtained for multilayers having PEI as the first layer comparing to films having the same number of layers but consisting of PAH/PSS only. We investigated the wettability of PEM surfaces using direct image analysis of the shape of sessile water drops. Periodic oscillations in contact angle were observed. PAH-terminated films were more hydrophobic than films with PSS as the outermost layer. The effect of long time conditioning of PEM films in solutions of various pH's or salt (NaCl) concentrations was also examined. Salt or base solutions induced modification in wetting properties of the polyelectrolyte multilayers but had a negligible effect on the film thickness.     

Formation of high-capacity protein-adsorbing membranes through simple adsorption of poly(acrylic acid)-containing films at low pH

Layer-by-layer polyelectrolyte adsorption is a simple, convenient method for introducing ion-exchange sites in porous membranes. This study demonstrates that adsorption of poly(acrylic acid) (PAA)-containing films at pH 3 rather than pH 5 increases the protein-binding capacity of such polyelectrolyte-modified membranes 3-6-fold. The low adsorption pH generates a high density of -COOH groups that function as either ion-exchange sites or points for covalent immobilization of metal-ion complexes that selectively bind tagged proteins. When functionalized with nitrilotriacetate (NTA)-Ni(2+) complexes, membranes containing PAA/polyethylenimine (PEI)/PAA films bind 93 mg of histidine(6)-tagged (His-tagged) ubiquitin per cm(3) of membrane. Additionally these membranes isolate His-tagged COP9 signalosome complex subunit 8 from cell extracts and show >90% recovery of His-tagged ubiquitin. Although modification with polyelectrolyte films occurs by simply passing polyelectrolyte solutions through the membrane for as little as 5 min, with low-pH deposition the protein binding capacities of such membranes are as high as for membranes modified with polymer brushes and 2-3-fold higher than for commercially available immobilized metal affinity chromatography (IMAC) resins. Moreover, the buffer permeabilities of polyelectrolyte-modified membranes that bind His-tagged protein are ~30% of the corresponding permeabilities of unmodified membranes, so protein capture can occur rapidly with low-pressure drops. Even at a solution linear velocity of 570 cm/h, membranes modified with PAA/PEI/PAA exhibit a lysozyme dynamic binding capacity (capacity at 10% breakthrough) of ~40 mg/cm(3). Preliminary studies suggest that these membranes are stable under depyrogenation conditions (1 M NaOH).     

Relationship between the growth regime of polyelectrolyte multilayers and the polyanion/polycation complexation enthalpy

The alternate deposition of polyanions and polycations leads to the formation of films called polyelectrolyte multilayer films (PEMs). Two types of growth processes are reported in the literature, leading to films that grow either linearly or exponentially with the number of deposition steps. In this article we try to establish a correlation between the nature of the growth process and the heat of complexation between the polyanions and the polycations constituting the PEM film. Isothermal titration microcalorimetry experiments performed on several polyanion/polycation systems seem to indicate that an endothermic complexation process is characteristic of an exponential film growth, whereas a strongly exothermic process corresponds to a linear growth regime. Finally, weakly exothermic processes seem to be associated with weakly exponentially growing films. These results thus show that exponentially growing processes are mainly driven by entropy. This explains why the exponential growth processes are more sensitive to temperature than the linear growing processes. This temperature sensitivity is shown on the poly-L-glutamic acid/poly(allylamine) system which grows either linearly or exponentially depending on the ionic strength of the polyelectrolyte solutions.     

Influence of the polyelectrolyte molecular weight on exponentially growing multilayer films in the linear regime

Alternated deposition of polyanions and polycations on a charged solid substrate leads to the buildup of polyelectrolyte multilayer (PEM) films. Two types of PEM films were reported in the literature: films whose thickness increases linearly and films whose thickness increases exponentially with the number of deposition steps. However, it was recently found that, for exponentially growing films, the exponential increase of the film thickness takes place only during the initially deposited pairs of layers and is then followed by a linear increase. In this study, we investigate the growth process of hyaluronic acid/poly(L-lysine) (HA/PLL) and poly(L-glutamic acid)/poly(allylamine) (PGA/PAH) films, two films whose growth is initially exponential, when the growth process enters the linear regime. We focus, in particular, on the influence of the molecular weight (Mw) of the polyelectrolytes. For both systems, we find that the film thickness increment per polyanion/polycation deposition step in the linear growth regime is fairly independent of the molecular weights of the polyelectrolytes. We also find that when the (HA/PLL)n films are constructed with low molecular weight PLL, these chains can diffuse into the entire film during each buildup cycle, even for very thick films, whereas the PLL diffusion of high molecular weight chains is restricted to the upper part of the film. Our results lead to refinement of the buildup mechanism model, introduced previously for the exponentially growing films, which is based on the existence of three zones over the entire film thickness. The mechanism no longer needs all the "in" and "out" diffusing polyanions or polycations to be involved in the buildup process to explain the linear growth regime but merely relies on the interaction between the polyelectrolytes with an upper zone of the film. This zone is constituted of polyanion/polycation complexes which are "loosely bound" and rich in the polyelectrolyte deposited during the former deposition step.     

Photo-cross-linkable polyelectrolyte multilayers for 2-D and 3-D patterning

We report the synthesis of poly(acrylic acid-ran-vinylbenzyl acrylate) (PAArVBA), a photo-cross-linkable weak polyelectrolyte, and its incorporation into polyelectrolyte multilayer (PEM) films. PEM films assembled from PAArVBA and poly(allylamine hydrochloride) (PAH) are found to exhibit similar thickness trends with assembly pH as those previously reported for poly(acrylic acid) (PAA)/PAH multilayers. Swelling properties of the as-built and photo-cross-linked films are studied by in situ ellipsometry. Two-dimensional masking techniques are used to pattern regions of high and low swelling, as confirmed by atomic force microscopy (AFM), and to provide spatial control over the low-pH-induced microporosity transition exhibited by PAH/PAA PEMs. Films containing alternating blocks of PAH/PAArVBA bilayers and PAH/PAA bilayers were assembled, laterally photopatterned, and exposed to low-pH solution to generate nanoporosity leading to patterned Bragg reflectors, thereby demonstrating three-dimensional control over film structure in these weak PEM assemblies.     

Water-soluble Polyelectrolytes Contaning Sulfonic Acid Groups with Metal Ion Binding Ability by Using the Liquid Phase Polymer Based Retention Technique

Water-soluble polyelectrolytes from 2-acrylamido-2-methyl-1-propane sulfonic acid (APSA) were obtained by radical polymerization with different comonomers which contain weak acid and neutral groups. These copolymers were investigated as polyelectrolytes and polychelatogens, in view of their metal ion binding properties using the liquid-phase polymer-based retention (LPR) technique under different experimental conditions. The metal ions investigated were: Ag(I), Co(II), Cu(II), Zn(II), Cd(II), and Pb(II). APSA allowed increase metal ion interaction of weak acid, meanwhile did not improve the metal ion interaction of neutral monomers at these experimental conditions. Results indicated that retention capability depended strongly on the structure of the polyelectrolyte, arrangement of comonomers at main chain, pH, and the filtration factor, Z.     

Incorporation of triazole into a quinoline-rhodamine conjugate imparts iron(iii) selective complexation permitting detection at nanomolar levels

Two new rhodamine based probes 1 and 2 for the detection of Fe(3+) were synthesized and their selectivity towards Fe(3+) ions in the presence of other competitive metal ions tested. The probe 1 formed a coloured complex with Fe(3+) as well as Cu(2+) ions and revealed the lack of adequate number of coordination sites for selective complexation with Fe(3+). Incorporation of a triazole unit to the chelating moiety of 1 resulted in the probe 2, that displayed Fe(3+) selective complex formation even in the presence of other competitive metal ions like Li(+), Na(+), K(+), Cu(2+), Mg(2+), Ca(2+), Sr(2+), Cr(3+), Mn(2+), Fe(2+), Co(2+), Ni(2+), Zn(2+), Cd(2+), Hg(2+) and Pb(2+). The observed limit of detection of Fe(3+) ions (5 × 10(-8) M) confirmed the very high sensitivity of 2. The excellent stability of 2 in physiological pH conditions, non-interference of amino acids, blood serum and bovine serum albumin (BSA) in the detection process, and the remarkable selectivity for Fe(3+) ions permitted the use of 2 in the imaging of live fibroblast cells treated with Fe(3+) ions.     

Photopatterned nanoporosity in polyelectrolyte multilayer films

We report on spatial control of nanoporosity in polyelectrolyte multilayer (PEM) films using photopatterning and its effects on film optical and adsorption properties. Multilayers assembled from poly(acrylic acid-ran-vinylbenzyl acrylate) (PAArVBA), a photo-cross-linking polymer, and poly(allylamine hydrochloric acid) (PAH) were patterned using ultraviolet light followed by immersion in low pH and then neutral pH solutions to induce nanoporosity in unexposed regions. Model charged small molecules rhodamine B, fluorescein, and propidium iodide and the model protein albumin exhibit increased adsorption to nanoporous regions of patterned PEM films as shown by fluorescence microscopy and radiolabeling experiments. Films assembled with alternating stacks of PAH/poly(sodium-4-styrene sulfonate) (SPS), which do not become nanoporous, and stacks of PAH/PAArVBA were patterned to create nanoporous capillary channels. Interdigitated channels demonstrated simultaneous, separate wicking of dimethyl sulfoxide-solvated fluorescein and rhodamine B. In addition, these heterostack structures exhibited patternable Bragg reflectivity of greater than 25% due to refractive index differences between the nanoporous and nonporous stacks. Finally, the PEM assembly process coupled with photo-cross-linking was used to create films with two separate stacked reflective patterns with a doubling in reflectivity where patterns overlapped. The combined adsorptive and reflective properties of these films hold promise for applications in diagnostic arrays and therapeutics delivery.     

Effect of acid-base equilibria on the donnan potential of layer-by-layer redox polyelectrolyte multilayers

In polymer films carrying an excess of fixed charge the electrostatic penalty to bring ions of same charge from the bathing electrolyte into the film sets a membrane potential (Donnan Potential) across the film-electrolyte interface. This potential is responsible for the ionic permselectivity observed in polyelectrolyte membranes. We have used electrochemical measurements to probe the dependence of the Donnan potential on the acid-base equilibrium in layer-by-layer self-assembled polyelectrolyte multilayers. The voltammperogram peak position of the Os(III)/Os(II) couple in self-assembled polyelectrolyte multilayers comprised of poly(allylamine) derivatized with Os(bpy)(2)PyCl+ and poly(vinylsulfonate) was recorded in solutions of increasing ionic strength for different assembly and testing solution pH. Protonation-deprotonation of the weak redox poly(allylamine) changes the fixed charge population in the as prepared (intrinsic) self-assembled redox polyelectrolyte multilayers. For films assembled in solutions of pH higher than the test solution pH, the Donnan plots (E(app) vs log C) exhibit a negative slope (anionic exchanger) while for films assembled at lower pH than that of the test solution positive slopes (cationic exchanger) are apparent. The ion exchange mechanism has been supported by complementary electrochemical quartz crystal microbalance. X-ray photoelectron spectroscopy and infrared reflection-absorption spectroscopy experiments demonstrated that the as prepared films have a memory effect on their protonation state during assembly, which leads to the observed dependence of the Donnan potential on the adsorption pH.     

Human serum albumin self-assembly on weak polyelectrolyte multilayer films structurally modified by pH changes

Adsorption of proteins onto film surfaces built up layer by layer from oppositely charged polyelectrolytes is a complex phenomenon, governed by electrostatic forces, hydrogen bonds, and hydrophobic interactions. The amounts of the interacting charges, however, both in polyelectrolytes and in proteins adsorbed on such films are a function of the pH of the solution. In addition, the number and the accessibility of free charges in proteins depend on the secondary structure of the protein. The subtle interplay of all these factors determines the adsorption of the proteins onto the polyelectrolyte film surfaces. We investigated the effect of these parameters for polyelectrolyte films built up from weak "protein-like" polyelectrolytes (i.e., polypeptides), poly(L-lysine) (PLL), and poly(glutamic acid) (PGA) and for the adsorption of human serum albumin (HSA) onto these films in the pH range 3.0-10.5. It was found that the buildup of the polyelectrolyte films is not a simple function of the pure charges of the individual polyelectrolytes, as estimated from their respective pKa values. The adsorption of HSA onto (PLL/PGA)n films depended strongly on the polyelectrolyte terminating the film. For PLL-terminated polyelectrolyte films, at low pH, repulsion, as expected, is limiting the adsorption of HSA (having net positive charge below pH 4.6) since PLL is also positively charged here. At high pH values, an unexpected HSA uptake was found on the PGA-ending films, even when both PGA and HSA were negatively charged. It is suggested that the higher surface rugosity and the decrease of the alpha-helix content at basic pH values (making accessible certain charged groups of the protein for interactions with the polyelectrolyte film) could explain this behavior.     

A two-component polymeric optode membrane based on a multifunctional ionic liquid

This work details the use of a 2-component optode membrane which is capable of generating three distinct colours in the presence of Cu(2+) and Co(2+) ions. It has been found that the ionic liquid (IL) trihexyltetradecylphosphonium dicyanamide [P(6,6,6,14)][DCA] can act as plasticizer, ligand and transducer dye when used in poly(vinyl chloride) (PVC) membranes, which significantly simplifies the optode membrane cocktail. Upon exposure to an aqueous Cu(2+) solution, a yellow colour is generated within the membrane, while exposure to an aqueous Co(2+) solution generates a blue colour. Exposure to a solution containing both ions produces a green colour. Vibrational spectroscopy has been used to investigate the molecular basis of the IL-metal ion the binding mechanism. Analytical characteristics of the membranes including the effect of interfering ions, binding constants and the limit of detection for both ions have been estimated. Finally the case of simultaneous dual-analyte recognition is presented based on two distinct absorption maxima.     

Structural and electronic characterization of the complexes obtained by the interaction between bare and hydrated first-row transition-metal ions (Mn(2+), Fe(2+), Co(2+), Ni(2+), Cu(2+), Zn(2+)) and glycine

The complexes formed by the simplest amino acid, glycine, with different bare and hydrated metal ions (Mn(2+), Fe(2+), Co(2+), Ni(2+), Cu(2+), Zn(2+)) were studied in the gas phase and in solvent in order to give better insight into the field of the metal ion-biological ligand interactions. The effects of the size and charge of each cation on the organization of the surrounding water molecules were analyzed. Results in the gas phase showed that the zwitterion of glycine is the form present in the most stable complexes of all ions and that it usually gives rise to an eta(2)O,O coordination type. After the addition of solvation sphere, a resulting octahedral arrangement was found around Ni(2+), Co(2+), and Fe(2+), ions in their high-spin states, whereas the bipyramidal-trigonal (Mn(2+) and Zn(2+)) or square-pyramidal (Cu(2+)) geometries were observed for the other metal species, according to glycine behaves as bi- or monodentate ligand. Despite the fact that the zwitterionic structure is in the ground conformation in solution, its complexes in water are less stable than those obtained from the canonical form. Binding energy values decrease in the order Cu(2+) > Ni(2+) > Zn(2+) approximately Co(2+) > Fe(2+) > Mn(2+) and Cu(2+) > Ni(2+) > Mn(2+) approximately Zn(2+) > Fe(2+) > Co(2+) for M(2+)-Gly and Gly-M(2+) (H(2)O)(n) complexes, respectively. The nature of the metal ion-ligand bonds was examined by using natural bond order and charge decomposition analyses.