The optimisation of facile substrates for surface enhanced Raman scattering through galvanic replacement of silver onto copper

A fast and cost-effective approach for the synthesis of substrates used in surface enhanced Raman scattering (SERS) has been developed using galvanic displacement. Deposition of silver onto commercially available Cu foil has resulted in the formation of multiple hierarchical structures, whose morphology show dependence on deposition time and temperature. Analysis of the surface structure by scanning electron microscopy revealed that the more complex silver structures correlated well with increased deposition time and temperature. Using Rhodamine 6G (R6G) as a model Raman probe it was also possible to relate the substrate morphology directly with subsequent SERS intensity from the R6G analyte as well as the reproducibility across a total of 15 replicate Raman maps (20 × 20 pixels) consisting of 400 spectra at a R6G concentration of 10(-4) M. The substrate with the highest reproducibility was then used to explore the limit of detection and this compared very favourably with colloidal-based SERS assessments of the same analyte.     

三维树枝状银薄膜的可控生长及其在表面增强拉曼光谱中的应用

通过电流置换反应制备了树枝状银纳米薄膜。在反应过程中通过控制反应时间和硝酸银的浓度,得到了不同形貌、分布和密度的树枝状银薄膜,从而得到了具有不同SERS性能的树枝状银纳米薄膜。选取了具有最佳SERS性能的树枝状银纳米薄膜对罗丹明6G进行了微量检测、再现性检测和稳定性检测,其检测限可达到1×10^-11 mol·L^-1,具有优良的再现性和良好的稳定性。     

三维树枝状银薄膜的可控生长及其在表面增强拉曼光谱中的应用

通过电流置换反应制备了树枝状银纳米薄膜。在反应过程中通过控制反应时间和硝酸银的浓度,得到了不同形貌、分布和密度的树枝状银薄膜,从而得到了具有不同SERS性能的树枝状银纳米薄膜。选取了具有最佳SERS性能的树枝状银纳米薄膜对罗丹明6G进行了微量检测、再现性检测和稳定性检测,其检测限可达到1×10~(-11) mol·L~(-1),具有优良的再现性和良好的稳定性。     

Silver nanocubes monolayers as a SERS substrate for quantitative analysis

Surface-enhanced Raman scattering (SERS) is a powerful spectroscopic tool in quantitative analysis of molecules, where the substrate plays a critical role in determining the detection performance. Herein, a silver nanocubes/polyelectrolyte/gold film sandwich structure was prepared as a reproducible, high-performance SERS substrate by the water/oil interfacial assembly method. In addition to the hot spots on the nanocubes surface, the edge-to-edge interspace of the Ag nanocubes led to marked enhancement of the SERS intensity, with a limit of detection of 10^?11 mol/L and limit of quantitation of 10^?10 mol/L for crystal violet. When rhodamine 6G and crystal violet were co-adsorbed on the Ag nanocube surfaces, the characteristic SERS peaks of the two molecules remained well resolved and separated, and the peak intensities varied with the respective concentration, which could be exploited for concurrent detection of dual molecules. Results from this work indicate that organized ensembles of Ag nanocubes can serve as effective SERS substrate can for sensitive analysis for complex molecular systems.     

Facile synthesis of two-dimensional PA-Ag@C film for highly sensitive SERS detection

In this study, the surface of polyamide (PA) films are electrostatically deposited with the carbon-coated silver (Ag@C) nanoparticles, resulting in a two-dimensional (2D) PA-Ag@C film substrate. The TEM images demonstrate that the nanoparticles were successful synthesized. By adjusting the pH of the system, the core–shell structure and the 2D SERS substrate work together to improve the sensitivity, stability, and repeatability of the substrate to be used in complex real-world water samples. The SERS enhancement effect and substrate uniformity were determined using rhodamine 6G (R6G), crystal violet (CV), and malachite green (MG). The results indicate that the 2D PA-Ag@C film substrate in this study has the optimal Raman effect at a system pH of 6. Under ideal pH conditions, the R6G detection limit (LOD) is as low as 10⁻¹⁰ M (D2 attenuation), and the Raman signal intensity deviation of the same substrate is maintained within 9.49%. Overall, the Raman signal of probe molecule on the fabricated PA-Ag@C film possesses excellent sensitivity, repeatability, and stability.     

Silver CD-R based substrate as a SERS active material

A silver Compact Disc Recortable (CD-R) based substrate has been proposed as an alternative to silver colloids as active material successfully used in surface-enhanced Raman spectroscopy (SERS). Scanning Electron Microscope (SEM) and Energy-Dispersive X-ray Spectroscopy (EDXS) measurements revealed that silver nanoparticles are present over the entire surface of the uncovered reflective layer of commonly used CD-R. The process of preparation of the CD-R based surface is simple, fast and repeatable. Recorded Raman spectra of 10 µM Rhodamine 6G applied to the substrate corroborate strong enhancement of Raman signal. The maximum value of EF was calculated to be about 5.76 × 10⁶. Raman maps are consistent with SEM micrographs and confirmed the presence of a numerous SERS hot spots occurring on the trucks of CD-R based substrate.     

3D aluminum/silver hierarchical nanostructure with large areas of dense hot spots for surface‐enhanced raman scattering

Plasmonic nanomaterials possessing large‐volume, high‐density hot spots with high field enhancement are highly desirable for ultrasensitive surface‐enhanced Raman scattering (SERS) sensing. However, many as‐prepared plasmonic nanomaterials are limited in available dense hot spots and in sample size, which greatly hinder their wide applications in SERS devices. Here, we develop a two‐step physical deposition protocol and successfully fabricate 3D hierarchical nanostructures with highly dense hot spots across a large scale (6 × 6 cm²). The nanopatterned aluminum film was first prepared by thermal evaporation process, which can provide 3D quasi‐periodic cloud‐like nanostructure arrays suitable for noble metal deposition; then a large number of silver nanoparticles with controllable shape and size were decorated onto the alumina layer surfaces by laser molecular beam epitaxy, which can realize large‐area accessible dense hot spots. The optimized 3D‐structured SERS substrate exhibits high‐quality detection performance with excellent reproducibility (13.1 and 17.1%), whose LOD of rhodamine 6G molecules was 10^?9 M. Furthermore, the as‐prepared 3D aluminum/silver SERS substrate was applied in detection of melamine with the concentration down to 10^?7 M and direct detection of melamine in infant formula solution with the concentration as low 10 mg/L. Such method to realize large‐area hierarchical nanostructures can greatly simplify the fabrication procedure for 3D SERS platforms, and should be of technological significance in mass production of SERS‐based sensors.     

Silver Nanoparticle Thin Films with Nanocavities for Surface‐Enhanced Raman Scattering

The formation of nanometer‐sized gaps between silver nanoparticles is critically important for optimal enhancement in surface‐enhanced Raman scattering (SERS). A simple approach is developed to generate nanometer‐sized cavities in a silver nanoparticle thin film for use as a SERS substrate with extremely high enhancement. In this method, a submicroliter volume of concentrated silver colloidal suspension stabilized with cetyltrimethylammonium bromide (CTAB) is spotted on hydrophobic glass surfaces prepared by the exposure of the glass to dichloromethysilane vapors. The use of a hydrophobic surface helps the formation of a more uniform silver nanoparticle thin film, and CTAB acts as a molecular spacer to keep the silver nanoparticles at a distance. A series of CTAB concentrations is investigated to optimize the interparticle distance and aggregation status. The silver nanoparticle thin films prepared on regular and hydrophobic surfaces are compared. Rhodamine 6G is used as a probe to characterize the thin films as SERS substrates. SERS enhancement without the contribution of the resonance of the thin film prepared on the hydrophobic surface is calculated as 2×10⁷ for rhodamine 6G, which is about one order of magnitude greater than that of the silver nanoparticle aggregates prepared with CTAB on regular glass surfaces and two orders of magnitude greater than that of the silver nanoparticle aggregates prepared without CTAB on regular glass surfaces. A hydrophobic surface and the presence of CTAB have an increased effect on the charge‐transfer component of the SERS enhancement mechanism. The limit of detection for rhodamine 6G is estimated as 1.0×10^?8 M . Scanning electron microscopy and atomic force microscopy are used for the characterization of the prepared substrate.     

A facile chemical approach for preparing a SERS active silver substrate

This communication describes a new surface-enhanced Raman scattering (SERS) active silver substrate prepared by iodination of the evaporated silver foil. After iodination, the morphology of the silver substrate undergoes a self-evolution process in which it displays accordingly the UV-vis absorption shift as well as the AFM topological test. Rhodamine 6G (R6G) is used as the probe molecule to evaluate the enhancement efficiency of the silver substrate at different self-evolution time intervals. The SERS intensity of R6G increases up to ～29-fold and reaches a maximum after the substrate evolved for 24 h. This method is feasible for the production of an efficient SERS silver substrate.     

Strategy for obtaining improved surface-enhanced Raman scattering by combining electrochemical and plasmas technologies

In this work, surface-enhanced Raman scattering (SERS)-active gold substrates were first developed by combining the technologies of oxidation–reduction cycles (ORCs) and plasmas treatments in roughening metal substrates. First, a gold substrate was treated by argon plasmas. Then the treated gold substrate was further roughened by triangular-wave ORCs in an aqueous solution containing 0.1 M HCl. Encouragingly, the SERS of Rhodamine 6G (R6G) adsorbed on this roughened gold substrate modified by argon plasmas pretreatment exhibits a higher intensity by 10-fold of magnitude and a better resolution, as compared with the SERS of R6G adsorbed on an unmodified roughened gold substrate. Meanwhile, the probing concentration of R6G adsorbed on the modified substrate can be reduced by one order. It was also found that the pretreatment of argon plasmas demonstrates a positive effect on the (2 2 0) face of Au partly changing into the (1 1 1) face with the lowest surface energy after the ORCs roughening, which is contributive to the improved SERS observed.     

银纳米粒子簇的设计、 制备和表面增强拉曼光谱

通过匹配激光光斑直径与胶体微球的尺寸, 设计制备了银纳米粒子的表面增强拉曼散射(SERS)基底, 并将其用于研究单个银纳米粒子簇的表面增强拉曼光谱. 在制备纳米粒子的过程中, 考察了等离子体刻蚀时间与银沉积厚度对“单”银纳米粒子结构与形貌的影响. 将吡啶、 巯基苯和罗丹明R6G作为SERS探针分子, 研究了其SERS效应, 通过荧光共振能量转移(FRET)机理, 实现了染料分子在单银纳米粒子簇上的SERS效应. SERS光谱测试与相关计算结果表明, 单个银纳米粒子簇的拉曼增强因子能够达到约10⁶.     

Ultrastable substrates for surface-enhanced Raman spectroscopy: Al2O3 overlayers fabricated by atomic layer deposition yield improved anthrax biomarker detection

A new method to stabilize and functionalize surfaces for surface-enhanced Raman spectroscopy (SERS) is demonstrated. Atomic layer deposition (ALD) is used to deposit a sub-1-nm alumina layer on silver film-over-nanosphere (AgFON) substrates. The resulting overlayer maintains and stabilizes the SERS activity of the underlying silver while presenting the surface chemistry of the alumina overlayer, a commonly used polar adsorbent in chromatographic separations. The relative affinity of analytes for alumina-modified AgFON substrates can be determined by their polarity. On the basis of SERS measurements, dipicolinic acid displays the strongest binding to the ALD alumina-modified AgFON among a set of pyridine derivatives with varying polarity. This strong affinity for carboxylate groups makes the SERS substrate an ideal candidate for bacillus spores detection using the dipicolinate biomarker. The SERS signal from extracted dipicolinate was measured over the spore concentration range 10(-14)-10(-12) M to determine the saturation binding capacity of the alumina-modified AgFON surface. The adsorption constant was determined to be Kspore = 9.0 x 10(13) M(-1). A 10-s data collection time is capable of achieving a limit of detection of approximately 1.4 x 10(3) spores. The shelf life of prefabricated substrates is at least 9 months prior to use. In comparison to the bare AgFON substrates, the ALD-modified AgFON substrates demonstrate twice the sensitivity with 6 times shorter data acquisition time and 7 times longer temporal stability. ALD expands the palette of available chemical methods to functionalize SERS substrates, which will enable improved and diverse chemical control over the nature of analyte-surface binding for biomedical, homeland security, and environmental applications.     

银/金纳米线阵列表面增强拉曼基底的制备及对孔雀石绿的高灵敏度检测

利用种子介导的软模板生长方法制备了金纳米线(Au NWs)阵列, 通过调节生长温度控制Au NWs阵列的形貌, 最后在经硼氢化钠(NaBH₄)清洗过的Au NWs阵列上化学沉积银纳米颗粒(Ag NPs), 制得银/金纳米线(Ag/Au NWs)阵列作为表面增强拉曼散射(SERS)基底. 选用罗丹明6G(R6G)作为拉曼探针分子测定了Ag/Au NWs阵列的SERS性能. 结果表明, Ag/Au NWs阵列作为SERS基底具有高灵敏度、 优异的信号均匀性和良好的稳定性. 使用Ag/Au NWs阵列对孔雀石绿(MG)检测的检出限可低至1×10^-8 mol/L, 线性范围为 1×10^-8~1×10^-4 mol/L. NaBH₄可以在不影响SERS性能的情况下去除Ag/Au NWs阵列上吸附的分子, 使得 SERS基底可以重复使用. 使用Ag/Au NWs阵列对湖水中的MG进行检测, 得到了可靠的回收率, 证明Ag/Au NWs 阵列在检测环境水体中的孔雀石绿上具有应用潜力.     

Immunoassay using probe-labelling immunogold nanoparticles with silver staining enhancement via surface-enhanced Raman scattering

This paper reports a novel immunoassay based on surface-enhanced Raman scattering (SERS) and immunogold labelling with silver staining enhancement. Immunoreactions between immunogold colloids modified by a Raman-active probe molecule (e.g., 4-mercaptobenzoic acid) and antigens, which were captured by antibody-assembled chips such as silicon or quartz, were detected via SERS signals of Raman-active probe molecule. All the self-assembled steps were subjected to the measurements of ultraviolet-visible (UV-vis) spectra to monitor the formation of a sandwich structure onto a substrate. The immunoassay was performed by a sandwich structure consisting of three layers. The first layer was composed of immobilized antibody molecules of mouse polyclonal antibody against Hepatitis B virus surface antigen (PAb) on a silicon or quartz substrate. The second layer was the complementary Hepatitis B virus surface antigen (Antigen) molecules captured by PAb on the substrate. The third layer was composed of the probe-labelling immunogold nanoparticles, which were modified by mouse monoclonal antibody against Hepatitis B virus surface antigen (MAb) and 4-mercaptobenzoic acid (MBA) as the Raman-active probe on the surface of gold colloids. After silver staining enhancement, the antigen is identified by a SERS spectrum of MBA. A working curve of the intensity of a SERS signal at 1585 cm(-1) due to the [small nu](8a) aromatic ring vibration of MBA versus the concentration of analyte (Antigen) was obtained and the non-optimized detection limit for the Hepatitis B virus surface antigen was found to be as low as 0.5 [micro sign]g mL(-1).     

在铜箔上电辅助制备纳米银及其SERS应用研究

在电化学工作站上以铜箔为工作电极,以硝酸银和PVP混合液作为前驱溶液,利用循环伏安法电辅助制备了纳米银,得到在铜箔上紧密均匀分布的纳米银颗粒聚集体作为SERS基底。通过X射线粉末衍射、X射线光电子能谱、扫描电子显微镜等表征手段,对铜箔上负载的银纳米颗粒进行了形貌和成分的表征,探讨了PVP及电辅助方法对纳米银形貌及基底SERS活性的影响。以4-巯基吡啶和罗丹明6G为探针溶液研究了制备基底的SERS活性,同时还对基底的均匀性进行了研究,结果表明所制备的SERS基底具有良好的性能。     

Effects of electrolytes used in roughening gold substrates by oxidation–reduction cycles on surface-enhanced Raman scattering

In this work, the effects of electrolytes used in roughening gold substrates by electrochemical methods on surface-enhanced Raman scattering (SERS) were first investigated. First, gold substrates were roughened by triangular-wave oxidation–reduction cycles (ORC) in aqueous solutions containing different kinds of 0.1 M electrolytes. Then Rhodamine 6G (R6G) was used as Raman probe to examine this effect of electrolytes used on the SERS observed. The result indicates that the highest intensity of SERS of R6G was obtained on the roughened Au substrate prepared in 0.1 M NaCl, which was less used in the literature. Meanwhile, it was also found that the rougher surface morphology observed, which is contributive to the higher SERS obtained, is corresponding to the smaller cathodic peak area shown in the cyclic voltammograms for roughening the Au substrate.     

Nanostructured Ag surface fabricated by femtosecond laser for surface-enhanced Raman scattering

Femtosecond laser was employed to fabricate nanostructured Ag surface for surface-enhanced Raman scattering (SERS) application. The prepared nanostructured Ag surface was characterized by field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The FESEM images demonstrate the formation of nanostructure-covered femtosecond laser-induced periodic surface structure, also termed as ripples, on the Ag surface. The AFM images indicate that the surface roughness of the produced nanostructured Ag substrate is larger than the untreated Ag substrate. The XRD and XPS of the nanostructured Ag surface fabricated by femtosecond laser show a face centered cubic phase of metallic Ag and no impurities of Ag oxide species. The application of the produced nanostructured Ag surface in SERS was investigated by using rhodamine 6G (R6G) as a reference chemical. The SERS intensity of R6G in aqueous solution at the prepared nanostructured Ag surface is 15 times greater than that of an untreated Ag substrate. The Raman intensities vary linearly with the concentrations of R6G in the range of 10(-8)-10(-4)M. The present methodology demonstrates that the nanostructured Ag surface fabricated by femtosecond laser is potential for qualification and quantification of low concentration molecules.     

Sub-wavelength Raman spectroscopy on isolated silver islands

Surface Enhanced Raman Spectroscopy (SERS) is a valuable analytical tool for the investigation of molecules adsorbed on roughened noble metal surfaces. The shape, size, and surrounding of the metal protrusions play an important role in the Raman scattering enhancement. By combining scanning near-field optical microscopy (SNOM) with Raman spectroscopy the spatial resolution suffices for investigating isolated silver islands on SERS active substrates. We demonstrate an optical resolution below 70 nm for recording spectra on specifically prepared and fully characterized SERS substrates. For a quantitative evaluation of the SERS signal the spatial distribution of Rhodamine 6G (R6G) deposited on the SERS substrate was determined by friction force measurements. By comparing the Raman intensities of the SERS substrates with those of unmetallized support plates absolute SERS enhancement factors at specific locations on top and in the vicinity of the silver islands were determined directly.     

Preparation of Fe3O4@Ag SERS substrate and its application in environmental Cr(VI) analysis

A novel sensitive and recyclable SERS substrate which can actively concentrate chromate (Cr(VI)) in water and substantially enhance Raman signal was synthesized as uniform Fe(3)O(4)@Ag nanoparticles. The surface morphology, structure, and magnetic properties were characterized using transmission electron microscopy, atomic force microscopy, X-ray powder diffraction, X-ray photoelectron spectroscopy, and vibrating sample magnetometry analysis. The closely spaced Fe(3)O(4)@Ag substrate with a core-shell structure exhibited a 25 nm surface roughness. The high saturation magnetization at 48.35 emu g(-1) enabled the complete and rapid separation of the substrate from the solution. The sensitivity and reproducibility of the substrate were confirmed using a common SERS probe molecule, rhodamine 6G. SERS spectra of Cr(VI) in simulated and real contaminated water showed that the symmetric stretching vibrations of Cr-O occurred at 796 cm(-1). This SERS peak area exhibited a linear dependence (R(2)=0.9992) on the Cr(VI) concentration between 5 and 100 μg L(-1). Coexisting anions such as sulfate, nitrate, chloride, carbonate, and humic acid could decrease the sensitivity of the SERS analysis. However, the adverse effect of the competing ions may be eliminated by proper dilution of the raw sample. This study provides a reliable method for qualitative and quantitative analysis of Cr(VI).     

On-column silver substrate synthesis and surface-enhanced Raman detection in capillary electrophoresis

A new, simple, and efficient approach for on-column surface-enhanced Raman scattering (SERS) detection in capillary electrophoresis (CE) is reported. A ∼50-μm SERS substrate spot was prepared by laser-induced growth of silver particles in the 100-μm inner diameter CE capillary window or in a flow cell consisting of a 250-μm inner diameter fused silica capillary connector. For this purpose, the Raman laser was focused by a 20× objective into the detection window filled with a 0.5 mM silver nitrate and 10 mM citrate buffer solution. During the CE runs, the silver substrate spot was formed in a few seconds after the analyte injection, hence the analytes adsorbed sequentially to the silver surface when the detection window was reached, followed by desorption from the silver surface and continuing the electrophoretic migration to the capillary end. Thus, beyond migration time, valuable molecular specific information was delivered by the SERS spectra. Accurate separations and high-intensity SERS spectra are shown by CE-SERS time-dependent 3D electropherograms for the analytes rhodamine 6G, 4-(2-pyridylazo)resorcinol (PAR), PAR complex with Cu(II) and methylene blue at 0.25–25 ppm concentrations, by using 1.4–3.6 mW HeNe laser power and an acquisition time of 5 s for each spectrum. Before and after each analyte passes the detection window, clean background spectra were recorded and no memory effects perturbed the SERS detection. The silver substrate is characterized by a fast preparation rate, good reproducibility, a preparation success rate of over 95% and no mentionable influence on the electrophoretic migration time, the CE-SERS and CE-UV electropherograms being in good agreement. The successful coupling of CE and on-column SERS detection opens new perspectives for monitoring CE separations.