Physical vapor deposition of one-dimensional nanoparticle arrays on graphite: seeding the electrodeposition of gold nanowires

One-dimensional (1D) ensembles of 2-15 nm diameter gold nanoparticles were prepared using physical vapor deposition (PVD) on highly oriented pyrolytic graphite (HOPG) basal plane surfaces. These 1D Au nanoparticle ensembles (NPEs) were prepared by depositing gold (0.2-0.6 nm/s) at an equivalent thickness of 3-4 nm onto HOPG surfaces at 670-690 K. Under these conditions, vapor-deposited gold nucleated selectively at the linear step edge defects present on these HOPG surfaces with virtually no nucleation of gold particles on terraces. The number density of 2-15 nm diameter gold particles at step edges was 30-40 microm-1. These 1D NPEs were up to a millimeter in length and organized into parallel arrays on the HOPG surface, following the organization of step edges. Surprisingly, the deposition of more gold by PVD did not lead to the formation of continuous gold nanowires at step edges under the range of sample temperature or deposition flux we have investigated. Instead, these 1D Au NPEs were used as nucleation templates for the preparation by electrodeposition of gold nanowires. The electrodeposition of gold occurred selectively on PVD gold nanoparticles over the potential range from 700-640 mV vs SCE, and after optimization of the electrodeposition parameters continuous gold nanowires as small as 80-90 nm in diameter and several micrometers in length were obtained.     

Preparation of supported gold nanoparticles by a modified incipient wetness impregnation method

In this work, we show that if the mere procedure of impregnation of oxide supports with chloroauric acid, which is well-known to lead to large gold particles, is followed by a step of washing with ammonia, small gold particles (3-4 nm) can be obtained after a treatment of calcination at 300 degrees C on any type of oxide supports (alumina, titania, silica). Moreover, gold leaching is very limited during the washing step, and a large range of gold loadings (0.7-3.5 wt %) can be achieved. Elemental analysis, Raman spectroscopy, and temperature programmed desorption under argon show that this ammonia posttreatment results in the removal of chloride ligands from the coordination sphere of Au(III) precursor and their replacement by ammine ligands, leading to an ammino-hydroxo or an ammino-hydroxo-aquo gold complex and not to gold hydroxide. The Au/TiO(2) catalysts prepared with this modified procedure of impregnation are almost as active as those prepared by deposition-precipitation with urea in the CO oxidation reaction performed at room temperature.     

Electrochemical Fabrication of Nanostructured Surfaces for Enhanced Response

The objective of this work is to explore approaches to enhance electrochemical signals through sequential deposition and capping of gold particles. Gold nanoparticles are electrodeposited from KAuCl₄ solution under potentiostatic conditions on glassy carbon substrates. The number density of the nanoparticles is increased by multiple deposition steps. To prevent secondary nucleation processes, the nanoparticles are isolated after each potentiostatic deposition step by self‐assembled monolayers (SAMs) of decanethiol or mercaptoethanol. The increasing number of particles during five deposition/protection rounds is monitored by assembling electroactive SAMs using a ferrocene‐labeled alkanethiol. A precise estimation of the surface area of the gold nanoparticles by formation of an oxide layer on gold is difficult due to oxidation of the glassy carbon surface. As an alternative approach, the charge flow of the electroactive SAM is used for surface measurement of the gold surface area. A sixfold increase in the redox signal in comparison to a bulk gold surface is observed, and this increase in redox signal is particularly notable given that the surface area of the deposited nanoparticles is only a fraction of the bulk gold surface. After five rounds of deposition there is a gold loading of 1.94 μg cm^?2 of the deposited nanoparticles as compared to 23.68 μg cm^?2 for the bulk gold surface. Remarkably, however, the surface coverage of the ferrocene alkanethiol on the bulk material is only 10 % of that achieved on the deposited nanoparticles. This enhancement in signal of the nanoparticle‐modified surface in comparison to bulk gold is thus demonstrated not to be attributable to an increase in surface area, but rather to the inherent properties of the surface atoms of the nanoparticles, which are more reactive than the surface atoms of the bulk material.     

Special features of the state of copper(II) oxide and its electric conductivity in porous glass

Controllable accumulation of copper(II) oxide in porous glass was carried out by repeated impregnation of the carrier by Cu(NO₃)₂ aqueous solutions with subsequent thermal decomposition of the salt. The results of measuring electric conductivity of a series of modified plates in combination with the data on the optical and X-ray electron spectroscopy make it possible to characterize two trends in the oxide distribution on a silica surface. In the case of its cyclic accumulation by small portions, a two-dimensional structure of monolayer filling the surface is presumably formed in a narrow range of CuO concentration, whereas the increase in the ??step?? of the accumulation gives rise to the formation and growth of island oxide particles.     

Janus particles with a functional gold surface for control of surface plasmon resonance

We report in this study the presence of Janus particles, which are candidates for use with electronic color papers. We used negatively charged polystyrene particles (370 nm) as the core particles, and gold was then sputtered onto their packed monolayer under several conditions. The sputtered particles were next redispersed into the aqueous medium by gentle sonication. Gold nanoparticles localized on one side of the cores could also serve as seeds for subsequent shell growth by electroless gold plating. Through these treatments, a series of well-dispersed Janus particles were obtained with gold nanostructures of different size and shape only on one side. Their dispersions showed different colors originating from the surface plasmon resonance absorption of gold nanoparticles localized on the hemisphere. The particles obtained by this approach have potential applications such as in sensors and electronic color paper.     

Gold three dimensional film electrode prepared from oppositely charged nanoparticles

Nanoparticulate gold film electrodes were prepared from oppositely charged gold nanoparticles (c.a. 6 nm diameter) by a layer-by-layer approach without application of linker molecules. This was done by alternative immersion of indium tin oxide plates into suspensions of positively and negatively charged particles. The thickness of the film and the magnitude of the characteristic surface plasmon band are proportional to the number of immersion and withdrawal steps. Up to nine double immersions and withdrawal steps can be used to systematically increase the amount of nanoparticulate gold material. The capacitive current density and current density of hydrogen peroxide reduction are proportional to the number of immersion and withdrawal steps. Highly efficient and low overpotential glucose electrooxidation in alkaline solution is demonstrated.     

Effect of hydrophobicity inside PEO-PPO-PEO block copolymer micelles on the stabilization of gold nanoparticles: experiments

In this paper we present the effect of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) block copolymer micelles and their hydrophobicity on the stabilization of gold nanoparticles. Gold nanoparticles were prepared by a method developed by Sakai et al. (Sakai, T.; Alexandridis, P. Langmuir 2004, 20, 8426). An absorption centered at 300-400 nm in time-dependent UV spectra provided evidence that the very first step of the synthesis was to form primary gold clusters. Then the gold clusters grew in size and were stabilized by block copolymer micelles. The stabilization capacities of the micelles were modulated by tuning the block copolymer concentration and composition and by adding salts. With good stabilization, gold particles were spherical and uniform in size with a diameter of 5-10 nm. Otherwise they were aggregates with irregular shapes such as triangular, hexagonal, and rodlike. The presence of a small amount of NaF significantly increased the stabilization capacity of the micelles and consequently modified the quality of the gold particles. Using FTIR and 1H NMR spectroscopy, micellization of the block copolymers and hydrophobicity of the micelles were proven very important for the stabilization. A higher hydrophobicity of the micelle cores was expected to favor the entrapment of primary gold clusters and the stabilization of gold nanoparticles.     

Mechanism of gold metal ion reduction, nanoparticle growth and size control in aqueous amphiphilic block copolymer solutions at ambient conditions

Spontaneous formation and efficient stabilization of gold nanoparticles with an average diameter of 7 approximately 20 nm from hydrogen tetrachloroaureate(III) hydrate (HAuCl4.3H2O) were achieved in air-saturated aqueous poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO) block copolymer solutions at ambient temperature in the absence of any other reducing agent. The particle formation mechanism is considered here on the basis of the block copolymer concentration dependence of absorption spectra, the time dependence (kinetics) of AuCl4- reduction, and the block copolymer concentration dependence of particle size. The effects of block copolymer characteristics such as molecular weight (MW), PEO block length, PPO block length, and critical micelle concentration (cmc) are explored by examining several PEO-PPO-PEO block copolymers. Our observations suggest that the formation of gold nanoparticles from AuCl4- comprises three main steps: (1) reduction of metal ions by block copolymer in solution, (2) absorption of block copolymer on gold clusters and reduction of metal ions on the surface of these gold clusters, and (3) growth of metal particles stabilized by block copolymers. While both PEO and PPO blocks contribute to the AuCl4- reduction (step 1), the PEO contribution appears to be dominant. In step 2, the adsorption of block copolymers on the surface of gold clusters takes place because of the amphiphilic character of the block copolymer (hydrophobicity of PPO). The much higher efficiency of particle formation attained in the PEO-PPO-PEO block copolymer systems as compared to PEO homopolymer systems can be attributed to the adsorption and growth processes (steps 2 and 3) facilitated by the block copolymers. The size of the gold nanoparticles produced is dictated by the above mechanism; the size increases with increasing reaction activity induced by the block copolymer overall molecular weight and is limited by adsorption due to the amphiphilic character of the block copolymers.     

Identification of nitrogen-containing species obtained by nitric oxide adsorption on the surface of model gold catalysts

Nitric oxide adsorption at 300–500 K on gold particles supported on an alumina film has been investigated for the first time by in situ X-ray photoelectron spectroscopy. Two nitrogen-containing adsorption species can form on the surface of gold particles. By test experiments on NO adsorption on the stepped face (533) of a gold single crystal, these species have been identified as adsorbed nitrogen atoms (which are detected throughout the temperature range examined) and a surface complex with N₂O stoichiometry (which is stable in a narrow temperature range of 325–425 K).     

组装在贵金属基底上的金纳米粒子对CO的电化学催化氧化

研究了组装在Au, Pt电极表面的金纳米粒子对CO的电化学催化氧化行为, 首次在实验上观察到较大粒径金纳米粒子(粒径＞10 nm)对CO的电催化氧化活性. 考察了金粒子表面金氧化物对粒子电催化活性的影响, 发现表面金氧化物的形成是金纳米粒子对CO具有电催化氧化活性的前提. 对于相同粒径的金纳米粒子, 随着粒子表面金氧化物量的增加,催化活性增大.     

Electrodeposition of gold particles on aluminum substrates containing copper

Electrodeposition of adhesive metal films on aluminum is traditionally preceded by the zincate process, which activates the aluminum surface. This paper presents an alternative approach for activation of aluminum by using films containing 99.5% aluminum and 0.5% copper. Aluminum/copper films are made amenable for subsequent electrodeposition by anodization followed by chemical etching of aluminum oxide. The electrodeposition of gold is monitored with electrochemical impedance spectroscopy (EIS). Analysis of EIS data suggests that electrodeposition of gold increases the interfacial capacitance from values typical for electrodes with thin oxide layers to values typical for metal electrodes. Scanning electron microscopy examination of aluminum/copper films following gold electrodeposition shows the presence of gold particles with densities of 10(5)-10(7) particles cm(-2). The relative standard deviation of mean particle diameters is approximately 25%. Evaluation of the micrographs suggests that the electrodeposition occurs by instantaneous nucleation followed by growth of three-dimensional semispherical particles. The gold particles, which are electrically connected to the conductive aluminum/copper film, support a reversible faradaic process for a soluble redox couple. The deposited gold particles are suitable for subsequent metallization of aluminum and fabrication of particle-type films with interesting catalytic, electrical, and optical properties.     

氧化铝水合物在聚苯乙烯上的覆盖

由两种或两种以上化合物组成的复合化合物均匀胶体位于制备越来越受到人们的重视[1-7]．作为复合粒子制备方法之一的覆盖技术，人们关注的多是一种无机化合物（金属，氧化物或盐）或有机物在另一种无机化合物上以壳状形式的沉积[3-7]，很少涉及在有机化合物或聚合物上覆盖问题[     

Observation and Identification of an Atomic Oxygen Structure on Catalytic Gold Nanoparticles

Interactions between oxygen and gold surfaces are fundamentally important in diverse areas of science and technology. In this work, an oxygen dimer structure was observed and identified on gold nanoparticles in catalytic decomposition of hydrogen peroxide to oxygen and water. This structure, which is different from isolated atomic or molecular oxygen surface structures, was observed with in situ surface‐enhanced Raman spectroscopic measurements and identified with density functional theory calculations. The experimental measurements were performed using monodisperse 5, 50 and 400 nm gold particles supported on silica with liquid‐phase hydrogen and deuterium peroxides at multiple pH values. The calculations show that on surfaces with coordinatively unsaturated gold atoms, two oxygen atoms preferentially share a gold atom with a bond distance of 0.194–0.196 nm and additionally bind to two other surface gold atoms with a larger bond distance of 0.203–0.213 nm, forming an Au‐O‐Au‐O‐Au structure. The formation of this structure depends on reaction rates and conditions.     

Preparation of various Janus composite particles with two components differently combined

Janus composite particles with a combination of organic and inorganic substances were synthesized by soap-free emulsion polymerization in which an amphoteric initiator of 2,2′-azobis[N-(2-carboxyethyl)-2-2-methylpropionamidine] (VA-057) was employed to introduce a polystyrene (PSt) lobe onto silica cores surface-modified with 3-methacryloxypropyltrimethoxy silane (MPTMS). Thermogravimetric analysis and X-ray photoelectron spectroscopy were used to characterize the surface-modified silica particles and showed that a small amount of MPTMS introduced onto the surface of silica particles could successfully prepare SiO₂–PSt Janus particles. The oxide part of SiO₂–PSt Janus particles obtained with the polymerization was further surface-modified with 3-aminopropyltriethoxysilane (APS) to introduce positively charged amino groups on the silica surface. The silica surface modified with APS was covered with gold by electroless deposition in which a gold precursor of auric chloride was reduced with ascorbic acid in the presence of polyvinylpyrrolidone. The electroless deposition of gold successfully produced Janus particles with a combination of gold and PSt surfaces. Furthermore, dissolution of the polymer component of the Au–PSt Janus particles in tetrahydrofuran led to another Janus type of particles with an inorganic combination of Au and SiO₂.     

氢在Ni(511)台阶面的吸附与解离研究

The adsorption and dissociation of hydrogen on stepped surface (511) of nickel are studied with the embedded-atom model (EAM) method. The adsorption energy, the length of the adsorption bond and the adsorption height for a single hydrogen atom are calculated. Three kinds of stable sites are found for hydrogen adsorption. There are the double-fold bridge site B on the step edge, the three-fold hollow site H3′ on the step surface and the four-fold hollow sites H1 and H2 on the terrace surface. Compared with a hydrogen atom adsorbed on low-index (001) surface, there are two other adsorption sites near the step: the two-fold bridge site B on the step edge and the three-fold hollow site H3′ on the step surface. At the same time, the absorbability of the hydrogen atom at the site H1 is intensified. The results show that hydrogen adsorption on Ni (511) is affected by the existence of the step. The active barriers, adsorption energy and corresponding bond length for dissociation of a hydrogen molecule on the stepped surface are presented. The results show that the dissociation is easier at the bottom of the step. It is shown that the steps are the active sites for hydrogen adsorption and dissociation.     

介电限域效应对SnO_2纳米微粒光学特性的影响

半导体纳米微粒作为一种新兴材料，在声、光、电、磁、热及催化等方面显示出全新的异于体相材料和分子或原子的特性，在理论和实验上已引起。们极大的兴趣I‘，’］．当纳米微粒的尺寸接近或小于激于玻尔半径时，表现出明显的量子尺寸效应，其表现光学能隙变大，一些半导体粒子如CdS，Cdse等纳米微粒的量予尺寸效应已经被人们利用有效质量近似模型做了定性解释。八但是，由于纳米微粒尺寸小，具有相对大的表面积，因而粒子周围的介质可以强烈地影响它们的光学性质【’，‘1．我们采用胶体化学方法，对SnO。阶电常数为13）半导体纳米微粒…     

Interaction of Pt clusters with the anatase TiO(2)(101) surface: a first principles study

The adsorption of Pt(n)() (n = 1-3) clusters on the defect-free anatase TiO(2)(101) surface has been studied using total energy pseudopotential calculations based on density functional theory. The defect-free anatase TiO(2)(101) surface has a stepped structure with a step width of two O-Ti bond distances in the (100) plane along the [10] direction and the edge of the step is formed by 2-fold-coordinated oxygen atoms along the [010] direction. For a single Pt adatom, three adsorption sites were found to be stable. Energetically, the Pt adatom prefers the bridge site formed by 2 2-fold-coordinated oxygen atoms with an adsorption energy of 2.84 eV. Electronic structure analysis showed that the Pt-O bonds formed upon Pt adsorption are covalent. Among six stable Pt(2) adsorption configurations examined, Pt(2) was found to energetically favor the O-O bridge sites on the step edge along [010] with the Pt-Pt bond axis perpendicular to [010]. In these configurations, one of the Pt atoms occupies the same O-O bridge site as for a single Pt adatom and the other one either binds a different 2-fold-coordinated oxygen atom on the upper step or a 5-fold-coordinated Ti atom on the lower terrace. Three triangular and three open Pt(3) structures were determined as minima for Pt(3) adsorption on the surface. Platinum trimers adsorbed in triangular structures are more stable than in open structures. In the most stable configuration, Pt(3) occupies the edge O-O site with the Pt(3) plane being upright and almost perpendicular to the [001] terrace. The preference of Pt(n)() to the coordinately unsaturated 2-fold-coordinated oxygen sites indicates that these sites may serve as nucleation centers for the growth of metal clusters on the oxide surface. The increase in clustering energy with increasing size of the adsorbed Pt clusters indicates that the growth of Pt on this surface will lead to the formation of three-dimensional particles.     

An investigation of the thermal decomposition of gold acetate

The thermal decomposition characteristics of gold acetate to produce gold nanoparticles were investigated. A rapid and violent fragmentation of the gold acetate particles was observed at approximately 103±20°C when a rapid heating rate of 25°C min⁻¹ was used, leading to formation of nanosized spherical and partially coalesced gold particles. Particle size analysis was used to investigate possible relationships between the gold acetate crystallite size and the gold nanoparticles produced by thermal decomposition. The results indicate rapid (<0.14 ms) coalescence of the gold particles occurs for fragments in close proximity.     

Origin and activity of gold nanoparticles as aerobic oxidation catalysts in aqueous solution

Whether gold is catalytically active on its own has been hotly debated since the discovery of gold-based catalysis in the 1980s. One of the central controversies is on the O(2) activation mechanism. This work, by investigating aerobic phenylethanol oxidation on gold nanoparticles in aqueous solution, demonstrates that gold nanoparticles are capable to activate O(2) at the solid-liquid interface. Extensive density functional theory (DFT) calculations combined with the periodic continuum solvation model have been utilized to provide a complete reaction network of aerobic alcohol oxidation. We show that the adsorption of O(2) is very sensitive to the environment: the presence of water can double the O(2) adsorption energy to ~0.4 eV at commonly available edge sites of nanoparticles (~4 nm) because of its strongly polarized nature in adsorption. In alcohol oxidation, the hydroxyl bond of alcohol can break only with the help of an external base at ambient conditions, while the consequent α-C-H bond breaking occurs on pure Au, both on edges and terraces, with a reaction barrier of 0.7 eV, which is the rate-determining step. The surface H from the α-C-H bond cleavage can be easily removed by O(2) and OOH via a H(2)O(2) pathway without involving atomic O. We find that Au particles become negatively charged at the steady state because of a facile proton-shift equilibrium on surface, OOH + OH ? O(2) + H(2)O. The theoretical results are utilized to rationalize experimental findings and provide a firm basis for utilizing nanoparticle gold as aerobic oxidation catalysts in aqueous surroundings.