CuCo2O4/NiFe层状双金属氢氧化物核壳纳米花球阵列的高效析氧反应

采用界面工程策略在泡沫镍(NF)上制备了CuCo₂O₄/NiFe层状双金属氢氧化物(LDH)(CuCo₂O₄/NiFe-LDH@NF)核壳纳米花球阵列。研究表明,电子通过CuCo₂O₄和NiFe-LDH耦合界面发生转移,导致核心CuCo₂O₄处于富电子状态,从而提高了反应速率。非晶态NiFe-LDH外壳不仅为电子/物质提供更多的传输通道和增加活性位点。同时,还能在电催化析氧反应(OER)中保护核心CuCo₂O₄免受强碱腐蚀。因此,在1.0 mol·L^-1 KOH溶液中,将CuCo₂O₄/NiFe-LDH@NF用作OER催化剂时,仅需191mV的低过电位即可实现10 mA·cm^-2的电流密度和31 mV·dec^-1的低Tafel斜率。此外,CuCo₂O₄/NiFe-LDH@NF在长时间的工作中能够保证催化性能、晶体结构、形貌结构和组成的稳定。     

The role of Li2MO2 structures (M=metal ion) in the electrochemistry of (x)LiMn0.5Ni0.5O2·(1−x)Li2TiO3 electrodes for lithium-ion batteries

The electrochemical reactions of lithium with layered composite electrodes (x)LiMn_0.5Ni_0.5O₂·(1−x)Li₂TiO₃ were investigated at low voltages. The metal oxide 0.95LiMn_0.5Ni_0.5O₂·0.05Li₂TiO₃ (x=0.95) which can also be represented in layered notation as Li(Mn_0.46Ni_0.46Ti_0.05Li_0.02)O₂, can react with one equivalent of lithium during an initial discharge from 3.2 to 1.4 V vs. Li⁰. The electrochemical reaction, which corresponds to a theoretical capacity of 286 mAh/g, is hypothesized to form Li₂(Mn_0.46Ni_0.46Ti_0.05Li_0.02)O₂ that is isostructural with Li₂MnO₂ and Li₂NiO₂. Similar low-voltage electrochemical behavior is also observed with unsubstituted, standard LiMn_0.5Ni_0.5O₂ electrodes (x=1). In situ X-ray absorption spectroscopy (XAS) data of Li(Mn_0.46Ni_0.46Ti_0.05Li_0.02)O₂ electrodes indicate that the low-voltage (<1.8 V) reaction is associated primarily with the reduction of Mn⁴⁺ to Mn²⁺. Symmetric rocking-chair cells with the configuration Li(Mn_0.46Ni_0.46Ti_0.05Li_0.02)O₂/Li(Mn_0.46Ni_0.46Ti_0.05Li_0.02)O₂ were tested. These electrodes provide a rechargeable capacity in excess of 300 mAh/g when charged and discharged over a 3.3 to −3.3 V range and show an insignificant capacity loss on the initial cycle. These findings have implications for combating the capacity-loss effects at graphite, metal–alloy, or intermetallic negative electrodes against lithium metal-oxide positive electrodes of conventional lithium-ion cells.     

NixCo3‐xO4 Nanoneedle Arrays Grown on Ni Foam as an Efficient Bifunctional Electrocatalyst for Full Water Splitting

Developing highly active, stable and robust electrocatalysts based on earth‐abundant elements for oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) is important for many renewable energy conversion processes. Herein, Ni_xCo_3‐xO₄ nanoneedle arrays grown on 3D porous nickel foam (NF) was synthesized as a bifunctional electrocatalyst with OER and HER activity for full water splitting. Benefiting from the advantageous structure, the composite exhibits superior OER activity with an overpotential of 320 mV achieving the current density of 10 mA cm^?2. An exceptional HER activity is also acquired with an overpotential of 170 mV at the current density of 10 mA cm^?2. Furthermore, the catalyst also shows the superior activity and stability for 20 h when used in the overall water splitting cell. Thus, the hierarchical 3D structure composed of the 1D nanoneedle structure in Ni_xCo_3‐xO₄/NF represents an avenue to design and develop highly active and bifunctional electrocatalysts for promising energy conversion.     

g-C3N4/双钙钛矿复合材料的制备及氧催化性能

通过溶胶-凝胶法制备出不同Ni掺杂比例的双钙钛矿Sr_2Ni_xCo_(2-x)O_6(x=0.2,0.4,0.6,0.8),通过热分解法制备出具有层状结构的纳米颗粒g-C_3N_4,并制备其复合物催化剂。将双钙钛矿和g-C_3N_4分别制备成双功能电极片,用于测试其对氧还原(ORR)和氧析出(OER)的催化活性,然后选取具有最佳氧催化活性的Ni掺杂比例x=0.4的双钙钛矿与一定重量比例的g-C_3N_4进行复合,测试复合催化剂的氧催化活性。结果表明,复合后的催化剂催化效果明显优于单一催化剂,当g-C_3N_4添加量占双钙钛矿的30%(w/w)时复合催化剂催化氧还原反应的最大电流密度为395.7 mA·cm~(-2)(-0.6 V vs Hg/HgO),氧析出反应的最大电流密度为372.0mA·cm~(-2)(1 V vs Hg/HgO),这表明g-C_3N_4与Sr_2Ni_(0.4)Co_(1.6)O_6复合后协同催化能够提高双钙钛矿的氧催化活性。     

Bi2Ti2O7/TiO2复合纤维：原位水热合成及光催化性能

采用静电纺丝技术制备的TiO2纤维作为模板和反应物,通过原位水热合成了具有异质结构的Bi2Ti2O7/TiO2复合纤维。利用X射线衍射(XRD)、扫描电镜(SEM)、能量散射光谱(EDS)、高分辨透射电镜(HRTEM)和紫外可见吸收光谱(UV-Vis)等分析测试手段对样品的结构和形貌进行表征。以罗丹明B为模拟有机污染物进行光催化降解实验。结果表明:花状Bi2Ti2O7纳米结构均匀地生长在TiO2纤维上,制备了Bi2Ti2O7与TiO2相复合的光催化材料,其光谱响应范围拓宽至可见光区,与纯TiO2纤维相比可见光催化活性显著提高,且易于分离、回收和循环使用。初步探讨了Bi2Ti2O7/TiO2异质结的生长机制和光催化活性提高机理。     

CuCo2O4/NiFe层状双金属氢氧化物核壳纳米花球阵列的高效析氧反应

采用界面工程策略在泡沫镍(NF)上制备了 CuCo₂O₄/NiFe 层状双金属氢氧化物(LDH) (CuCo₂O₄/NiFe-LDH@NF)核壳纳米花球阵列。研究表明,电子通过CuCo₂O₄和NiFe-LDH耦合界面发生转移,导致核心CuCo₂O₄处于富电子状态,从而提高了反应速率。非晶态NiFe-LDH外壳不仅为电子/物质提供更多的传输通道和增加活性位点。同时,还能在电催化析氧反应(OER)中保护核心 CuCo₂O₄免受强碱腐蚀。因此,在 1.0 mol·L^-1 KOH 溶液中,将 CuCo₂O₄/NiFe-LDH@NF 用作 OER 催化剂时,仅需 191mV 的低过电位即可实现 10 mA·cm^-2的电流密度和 31 mV·dec^-1的低 Tafel斜率。此外,CuCo₂O₄/NiFe-LDH@NF 在长时间的工作中能够保证催化性能、晶体结构、形貌结构和组成的稳定。     

Li4Ti5O12/(Ag+C)电极材料的固相合成及电化学性能

以Li₂CO₃,TiO₂为原料,葡萄糖为碳源,采用固相煅烧工艺合成了亚微米级的Li₄Ti₅O₁₂/C复合负极材料。并将之与AgNO₃复合,采用固相方法制备出了Ag表面修饰的Li₄Ti₅O₁₂/(Ag+C)复合材料。采用XRD、SEM和TEM测试方法对材料的微结构进行了表征。结果表明,C的存在对Ag单质在Li₄Ti₅O₁₂/C颗粒表面的大量形成起到了积极的促进作用,从而很大程度地提高了Li₄Ti₅O₁₂/C的电导率,因此有效地改善了其电化学性能。在1C倍率下,Li₄Ti₅O₁₂/(Ag+C)复合材料的首次放电容量达到了164 mAh·g^-1。     

Li4Ti5O12/(Cu+C)复合材料的制备及电化学性能

以Li₄Ti₅O₁₂,Cu(CH₃COO)₂·H₂O和C₆H₁₂O₆为前驱体,化学沉积与热分解结合合成锂离子电池负极材料Li₄Ti₅O₁₂/(Cu+C)。采用X-射线衍射(XRD)、扫描电子显微镜(SEM)、恒流充放电、循环伏安和电化学阻抗方法表征样品的结构、形貌和电化学性能。结果表明,Li₄Ti₅O₁₂表面包覆的Cu与C提高了Li₄Ti₅O₁₂电极材料的导电率,其循环性能和倍率性能得到有效地改善。在0.5C、1C和3C倍率下,经过50次充放电循环,放电比容量分别为168.2、160、140.6 mAh·g^-1,其容量保持率分别为88.7%、84.4%、71.2%。电化学阻抗测试表明,表面包覆的Cu与C使其电荷转移阻抗大幅度减少。     

Water photoelectrolysis using nickel titanate and niobate as photoanodes

Nickel titanate (NiTiO₃) and nickel niobate (NiNb₂O₆), both with a cationic valence and conduction band, were examined for their photoelectrochemical properties. Applied as photoanode in a photoelectrochemical cell for water electrolysis, reduced pellets of these oxides show a photoresponse when irradiated in the optical band gap. The corresponding absorption is due to Ni²⁺ → Ti⁴⁺ and Ni²⁺ → Nb⁵⁺ charge-transfer transitions, respectively. These are situated at lower energy than the O^2? → Ti⁴⁺ and O^2? → Nb⁵⁺ charge-transfer transitions. The flatband potentials of both compounds were determined from photocurrent versus applied potential measurements. During reduction both compounds showed superficial decomposition. The effect of this decomposition on the photocurrents is discussed.     

In Situ Electrochemical Conversion of an Ultrathin Tannin Nickel Iron Complex Film as an Efficient Oxygen Evolution Reaction Electrocatalyst

The oxygen evolution reaction (OER) is an important half reaction in many energy conversion and storage techniques. However, the development of a low‐cost easy‐prepared OER electrocatalyst with high mass activity and rapid kinetics is still challenging. Herein, we report the facile deposition of tannin‐NiFe (TANF) complex film on carbon fiber paper (CP) as a highly efficient OER electrocatalyst. TANF gives rapid OER reaction kinetics with a very small Tafel slope of 28 mV dec^?1. The mass activity of TANF reaches 9.17×10³ Ag^?1 at an overpotential of 300 mV, which is nearly 200‐times larger than that of NiFe double layered hydroxide. Furthermore, tannic acid in TANF can be electrochemically extracted under anodic potential, leaving the inorganic composite Ni_xFe_1?xO_yH_z as the OER‐active species. This work may provide a guide to probing the electrochemical transformation and investigating the reactive species of other metal–organic complexes as heterogeneous electrocatalysts.     

Plasma‐Engraved Co3O4 Nanosheets with Oxygen Vacancies and High Surface Area for the Oxygen Evolution Reaction

Co₃O₄, which is of mixed valences Co²⁺ and Co³⁺, has been extensively investigated as an efficient electrocatalyst for the oxygen evolution reaction (OER). The proper control of Co²⁺/Co³⁺ ratio in Co₃O₄ could lead to modifications on its electronic and thus catalytic properties. Herein, we designed an efficient Co₃O₄‐based OER electrocatalyst by a plasma‐engraving strategy, which not only produced higher surface area, but also generated oxygen vacancies on Co₃O₄ surface with more Co²⁺ formed. The increased surface area ensures the Co₃O₄ has more sites for OER, and generated oxygen vacancies on Co₃O₄ surface improve the electronic conductivity and create more active defects for OER. Compared to pristine Co₃O₄, the engraved Co₃O₄ exhibits a much higher current density and a lower onset potential. The specific activity of the plasma‐engraved Co₃O₄ nanosheets (0.055 mA cm^?2_BET at 1.6 V) is 10 times higher than that of pristine Co₃O₄, which is contributed by the surface oxygen vacancies.     

Synthesis and Characterization of Europium‐exchanged Titanate Nanoporous Phosphors

Eu_x(NH₄)_2‐2xTi₃O₇ nanoporous phosphor was prepared by ion exchange method. (NH₄)₂Ti₃O₇ nanotubes were employed as the host structure by treating H₂Ti₃O₇ with NH₄OH solution and the activator, Eu²⁺, was introduced into the host via ion exchange. This is an easy and feasible way to prepare a phosphor. The synthesized samples were characterized using TEM, XRD, N₂ adsorption‐desorption isotherm, TPR, and fluorescence spectrophotometer. Experimental results showed that a portion of Eu²⁺ ions was oxidized into Eu³⁺ ions during ion exchange, resulting in the present phosphor with blue‐emitting and red‐emitting. Moreover, the tubular structure of Eu_x(NH₄)_2‐2xTi₃O₇ was distorted as Eu²⁺ was placed into the host structure. This distortion is attributed to the electrostatic interaction between Eu²⁺ and the electric field of the host structure.     

Synthesis,Characterization and Electrorheological Properties of Polyaniline/Titanate Core-Shell Composite

In this study, a facile method was developed for the preparation of a new conducting polymer composite with core-shell structure. The surfaces of layered titanate (K₂Ti₄O₉) particles were first modified with 3-aminopropyltriethoxysilane, and then a polyaniline/titanate (PANI/K₂Ti₄O₉) composite was synthesized via chemical oxidative polymerization. The resulting composites were characterized by SEM, XRD, FTIR and TG measurements. The results indicated that the PANI deposited on the surface of K₂Ti₄O₉ particles resulted in the formation of the composite with a core-shell structure. TG analysis showed that the composite containing 28.7 wt% PANI had better thermal stability than that of pure PANI. Further, the PANI/K₂Ti₄O₉ composite particles were adopted as a dispersed phase in silicone oil for electrorheological (ER) investigation. Suspension of the composite particles exhibited typical ER behavior subjected to an external electric field under steady and dynamic oscillatory shear.     

Impact of Surface Defects on LaNiO3 Perovskite Electrocatalysts for the Oxygen Evolution Reaction

Perovskite oxides are regarded as promising electrocatalysts for water splitting due to their cost-effectiveness, high efficiency and durability in the oxygen evolution reaction (OER). Despite these advantages, a fundamental understanding of how critical structural parameters of perovskite electrocatalysts influence their activity and stability is lacking. Here, we investigate the impact of structural defects on OER performance for representative LaNiO₃ perovskite electrocatalysts. Hydrogen reduction of 700 °C calcined LaNiO₃ induces a high density of surface oxygen vacancies, and confers significantly enhanced OER activity and stability compared to unreduced LaNiO₃; the former exhibit a low onset overpotential of 380 mV at 10 mA cm⁻² and a small Tafel slope of 70.8 mV dec⁻¹. Oxygen vacancy formation is accompanied by mixed Ni²⁺/Ni³⁺ valence states, which quantum-chemical DFT calculations reveal modify the perovskite electronic structure. Further, it reveals that the formation of oxygen vacancies is thermodynamically more favourable on the surface than in the bulk; it increases the electronic conductivity of reduced LaNiO₃ in accordance with the enhanced OER activity that is observed.     

A mixed cation nickel diphosphate with a layered intergrowth structure: synthesis, structural and magnetic characterization of Na(NH4)[Ni3(P2O7)2(H2O)2]

A nickel diphosphate with mixed cations, Na(NH₄)[Ni₃(P₂O₇)₂(H₂O)₂] with a layered structure has been synthesized under hydrothermal conditions for the first time and characterized by single crystal X-ray diffraction, IR spectroscope and magnetization measurements. The structure consists of cis- and trans-edge sharing NiO₆ octahedral chains linked via P₂O₇ units to [Ni₃P₄O₁₆]²⁻ layers. The ammonium and sodium cations are alternately located in the interlayer spaces. The mixed cations play an important role in the structural formation of this layered compound, leading to a new layer-stacking variant. The magnetic susceptibility obeys a Curie–Weiss law with μ_eff of 3.32 μ_B, showing the Ni²⁺ character and weak antiferromagnetic interactions.     

EPR Studies of Photoreduction of Ni/TiO2 Catalysts

Irradiations of Ni/TiO₂ catalyst by UV in hydrogen at 77 K produced not only Ni⁺ ions on the catalyst surface, but also Ni³⁺ and Ti³⁺ species in bulk or near the interface between nickel and titania. These photo-generated species were detected and characterized by low temperature electron paramagnetic resonance (EPR) spectroscopy. Relative spin concentrations of the photogenerated paramagnetic species (Niⁿ⁺ and Ti³⁺) varied with the nickel content in titania. A high nickel content in the sample resulted in a high peak intensity ratio of Niⁿ⁺ to Ti³⁺. It was found that the photoinduced self-redox reaction of Ni²⁺ ions to form Ni⁺ and Ni³⁺ ions has a priority over the photoreduction of Ti⁴⁺ to Ti³⁺ ions. The characteristic EPR spectrum of the Ni³⁺ (3d⁷) ions with g₁ = 2.268, g₂ = 2.237, and g₃ = 2.045 indicates that the Ni³⁺ ions are most likely located in the substitutional sites of TiO₂, possibly near the surface rutile phase. The Ni⁺ species (3d⁹) with g₄ = 2.130 and g₁ = 2.063 are on the surface of TiO₂. Both Ni⁺ and Ni³⁺ ions are quite stable in hydrogen. The Ni³⁺ ions seem to be responsible for anchoring the nickel ions onto titania and stablizing the Ni⁺ species on the surface. The Ni⁺ ions are thus free from oxygen poisoning and still show a high activity toward olefin oligomerization.     

Different Reactivity of Rutile and Anatase TiO2 Nanoparticles: Synthesis and Surface States of Nanoparticles of Mixed-Valence Magnéli Oxides

Magnéli phases Ti_nO_2n−1 (3<n≤10) are mixed Ti⁴⁺/Ti³⁺ oxides with high electrical conductivity. When used for water remediation or electrochemical energy storage and conversion, they are nanostructured and exposed to various environments. Therefore, understanding their surface reactivity is of prime importance. Such studies have been hindered by carbon contamination from syntheses. Herein, this synthetic and characterization challenge is addressed through a new approach to 50 nm carbon-free Ti₄O₇ and Ti₆O₁₁ nanoparticles. It takes advantage of the different reactivities of rutile and anatase TiO₂ nanoparticles towards H₂, to use the former as precursor of Ti_nO_2n−1 and the latter as a diluting agent. This approach is combined with silica templating to restrain particle growth. The surface reactivity of the Magnéli nanoparticles under different atmospheres was then evaluated quantitatively by synchrotron-radiation-based X-ray photoelectron spectroscopy, which revealed oxidized surfaces with lower conductivity than the core. This finding sheds a new light on the charge transfer occurring in these materials.     

Li4Ti5O12/CMK-3复合材料的制备及其作为锂离子电池负极材料的性能

将LiNO₃和Ti(OC₄H₉)₄填填充在有序介孔碳CMK-3 孔道中, 然后烧结合成了Li₄Ti₅O₁₂/CMK-3复合材料. 利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)和X射线衍射(XRD)对其结构和微观形貌进行了表征. 利用差热-热重分析(TG-DTA)测试复合材料中Li₄Ti₅O₁₂的含量. 利用充放电测试、循环伏安和电化学阻抗技术考察了复合材料作为锂离子电池负极材料的性能. 发现Li₄Ti₅O₁₂分布在CMK-3孔道中及其周围, 复合材料的高倍率充放电性能显著优于商品Li₄Ti₅O₁₂, 复合材料中Li₄Ti₅O₁₂的比容量明显高于除去CMK-3的样品(在1C倍率时比容量为117.8 mAh·g^-1), 其0.5C、1C和5C倍率的放电比容量分别为160、143 和131 mAh·g^-1, 库仑效率接近100%, 5C倍率时循环100次的容量损失率只有0.62%. 本研究结果表明CMK-3明显提高了Li₄Ti₅O₁₂的高倍率充放电性能, 可能是CMK-3特殊的孔道结构和良好的导电性减小了Li₄Ti₅O₁₂的粒径并提高了其电导率.     

Carboxymethylated polyethylenimine modified magnetic nanoparticles specifically for purification of His‐tagged protein

Employing immobilized metal‐ion affinity chromatography and magnetic separation could ideally provide a useful analytical strategy for purifying His‐tagged protein. In the current study, a facile route was designed to prepare CMPEI‐Ni²⁺@SiO₂@Fe₃O₄ (CMPEI=carboxymethylated polyethyleneimine) magnetic nanoparticles composed of a strong magnetic core of Fe₃O₄ and a Ni²⁺‐immobilized carboxymethylated polyethyleneimine coated outside shell, which was formed by electrostatic interactions between polyanionic electrolyte of carboxymethylated polyethyleneimine and positively charged surface of 3‐(trimethoxysilyl)propylamin modified SiO₂@Fe₃O₄. The resulting CMPEI‐Ni²⁺@SiO₂@Fe₃O₄ composite nanoparticles displayed well‐uniform structure and high magnetic responsiveness. Hexa His‐tagged peptides and purified His‐tagged recombinant retinoid X receptor alpha were chosen as the model samples to evaluate the adsorption, capacity, and reusability of the composite nanoparticles. The results demonstrated the CMPEI‐Ni²⁺@SiO₂@Fe₃O₄ nanoparticles possessed rapid adsorption, large capacity, and good recyclability. The obtained nanoparticles were further used to purify His‐tagged protein in practical environment. It was found that the nanoparticles could selectively capture His‐tagged recombinant retinoid X receptor protein from complex cell lysate. Owing to its easy synthesis, large binding capacity, and good reusability, the prepared CMPEI‐Ni²⁺@SiO₂@Fe₃O₄ magnetic nanoparticles have great potential for application in biotechnological fields.     

Effect of the high pressure on the structure and intercalation properties of lithium-nickel-manganese oxides

Lithium-nickel-manganese oxides (Li_1+x(Ni_1/2Mn_1/2)_1−xO₂, x=0 and 0.2), having different cationic distributions and an oxidation state of Ni varying from 2+ to 3+, were formed under a high-pressure (3 GPa). The structure and cationic distribution in these oxides were examined by powder X-ray diffraction, infrared (IR) and electron paramagnetic resonance (EPR) in X-band (9.23 GHz) and at higher frequencies (95 and 285 GHz). Under a high pressure, a solid-state reaction between NiMnO₃ and Li₂O yields LiNi_0.5Mn_0.5O₂ with a disordered rock-salt type structure. The paramagnetic ions stabilized in this oxide are mainly Ni²⁺ and Mn⁴⁺ together with Mn³⁺ (about 10%). The replacement of Li₂O by Li₂O₂ permits increasing the oxidation state of Ni ions in lithium-nickel-manganese oxides. The higher oxidation state of Ni ions favours the stabilization of the layered modification, where the Ni-to-Mn ratio is preserved: Li(Li_0.2Ni_0.4Mn_0.4)O₂. The paramagnetic ions stabilized in the layered oxide are mainly Ni³⁺ and Mn⁴⁺ ions. The disordered and ordered phases display different intercalation properties in respect of lithium. The changes in local Ni,Mn-environment during the electrochemical reaction are discussed on the basis of EPR and IR spectroscopy.