Sub-wavelength Raman spectroscopy on isolated silver islands

Surface Enhanced Raman Spectroscopy (SERS) is a valuable analytical tool for the investigation of molecules adsorbed on roughened noble metal surfaces. The shape, size, and surrounding of the metal protrusions play an important role in the Raman scattering enhancement. By combining scanning near-field optical microscopy (SNOM) with Raman spectroscopy the spatial resolution suffices for investigating isolated silver islands on SERS active substrates. We demonstrate an optical resolution below 70 nm for recording spectra on specifically prepared and fully characterized SERS substrates. For a quantitative evaluation of the SERS signal the spatial distribution of Rhodamine 6G (R6G) deposited on the SERS substrate was determined by friction force measurements. By comparing the Raman intensities of the SERS substrates with those of unmetallized support plates absolute SERS enhancement factors at specific locations on top and in the vicinity of the silver islands were determined directly.     

Silver–platinum core–shell nanoparticles for surface-enhanced Raman spectroscopy

Core–shell Ag@Pt nanoparticles have been synthesised by the means of seed-growth reaction including reduction of PtCl₄²⁻ with silver and replacing Ag atoms with Pt. Surface-enhanced Raman scattering (SERS) spectra of pyridine (which gives slightly different spectra when interacting with various metals) adsorbed on synthesised Ag@Pt clusters were measured. SERS measurements have revealed that deposition of the platinum layer causes near elimination of the spectral interferences from pyridine directly interacting with the silver core. The average SERS enhancement factor for pyridine adsorbed on the Ag@Pt clusters was estimated as equal to about 10³–10⁴, significantly higher than the SERS enhancement factor achievable on the pure platinum nanostructures. Using the silver core (instead of the previously used gold cores) allows for measurement of strong SERS spectra on the Pt covered nanostructures for the wider range of the excitation radiation. This procedure of platinum deposition was tested with various silver nanoparticles – produced with borohydride, citrate and citrate/borohydride methods – which substantially differ in size distribution. The application of formed Ag@Pt structures for obtaining intense Raman spectra for molecules adsorbed on only slightly modified platinum surfaces is discussed.     

Surface-enhanced Raman scattering measurements on silver nanoparticles covered with differently formed platinum films

Gold and silver electromagnetic nanoresonators covered by a thin layer of platinum are often used to study adsorption of various molecules on “model platinum surfaces” with surface-enhanced Raman scattering (SERS) spectroscopy. In this contribution spectra of pyridine adsorbed on films formed from core–shell Ag@Pt and Ag@Ag–Pt nanoparticles and pure Pt or Ag nanoparticles were measured using a confocal Raman microscope. The SERS spectra of pyridine adsorbed on alloy Ag@Ag–Pt nanoparticles could not be obtained as a linear combination of spectra measured on pure Ag and Pt surfaces. In other words, for silver electromagnetic nanoresonators covered by platinum there is no simple correlation between the “quality” of the deposited Pt layer and the relative intensity of SERS bands characteristic for adsorbate interacting with silver. The SERS spectra accumulated from various places of a film formed from Ag@Pt or Ag@Ag–Pt nanoclusters may differ significantly. Using Ag@Pt nanoparticles with practically negligible amount of Ag on the surface (as per the stripping measurement), it is possible to record SERS spectrum in which the contribution characteristic for pyridine adsorbed on the Ag surface is well visible. It means that, even for macroscopic samples of core–shell Ag–Pt nanoparticles, averaging of many spectra measured at various locations of the sample should be carried out to characterize reliably their properties.     

Silver Nano Islands Enhanced Raman Scattering on Large Area Grating Substrates Fabricated by Two Beam Laser Interference

The authors preparedlarge area surface-enhanced Raman scattering(SERS) active substrates with tunable enhancement. First the large area gratings were fabricated by scanning a photoresist with two-beam laser interference and subsequently they were coated with silver nano islands via vacuum evaporation. SERS active metal island grating substrates with four different periods(300, 400, 515 and 600 nm) and Ag nano islands uniformly coated on an area of 2.5 cm×0.5 cm were obtained. The measured SERS spectra reveal the tuning effect of the period on the Raman signals period. The highest enhancement(ca. 10⁵) for Rhodamine 6G(R6G) as probing molecule is associated with a period of 515 nm due to the perfect matching of surface plasmons and Raman excitation line. A good reproducibility of SERS signals with almost the same SERS intensity at different spots was observed on all the larger area Ag island grating substrates.     

贵金属在Ag_2S纳米颗粒中由内向外的迁移现象

纳米颗粒具有明显区别于块体材料的新奇特性,本文利用透射电镜观察,描述并讨论一种发生在贵金属(Au、Ag、Pd和Pt)和硫化银(Ag_2S)构成的核壳结构纳米颗粒中的有趣现象,即贵金属在Ag_2S纳米颗粒中由内向外的迁移。迁移可在室温下进行,其最终结果使最初的核壳结构颗粒演变成由贵金属和Ag_2S构成的异质纳米二聚体结构,如Au-Ag_2S、Ag-Ag_2S、PdAg_2S和Pt-Ag_2S。电镜表征表面实验条件下贵金属在Ag_2S的迁移类似于一种整体迁移的模式且迁移过程中伴随着颗粒形貌结构的演变。贵金属在Ag_2S中的经空位互换的扩散机制或半导体纳米颗粒的自纯化机制可以用来解释这种迁移现象。     

Noble‐Metal‐Free Materials for Surface‐Enhanced Raman Spectroscopy Detection

Surface‐enhanced Raman spectroscopy (SERS) is an attractive tool for the sensing of molecules in the fields of chemical and biochemical analysis as it enables the sensitive detection of molecular fingerprint information even at the single‐molecule level. In addition to traditional coinage metals in SERS analysis, recent research on noble‐metal‐free materials has also yielded highly sensitive SERS activity. This Minireview presents the recent development of noble‐metal‐free materials as SERS substrates and their potential applications, especially semiconductors and emerging graphene‐based nanostructures. Rather than providing an exhaustive review of this field, possible contributions from semiconductor substrates, characteristics of graphene enhanced Raman scattering, as well as effect factors such as surface plasmon resonance, structure and defects of the nanostructures that are considered essential for SERS activity are emphasized. The intention is to illustrate, through these examples, that the promise of noble‐metal‐free materials for enhancing detection sensitivity can further fuel the development of SERS‐related applications.     

Fabrication and characterization of homogeneous surface-enhanced Raman scattering substrates by single pulse UV-laser treatment of gold and silver films

The fabrication of SERS-active substrates, which offer high enhancement factors as well as spatially homogeneous distribution of the enhancement, plays an important role in the expansion of surface-enhanced Raman scattering (SERS) spectroscopy to a powerful, quantitative, and noninvasive measurement technique for analytical applications. In this paper, a novel method for the fabrication of SERS-active substrates by laser treatment of 20, 40, and 60 nm thick gold and of 40 nm thick silver films supported on quartz glass is presented. Single 308 nm UV-laser pulses were applied to melt the thin gold and silver films. During the cooling process of the noble metal, particles were formed. The particle size and density were imaged by atomic force microscopy. By varying the fluence, the size of the particles can be controlled. The enhancement factors of the nanostructures were determined by recording self-assembled monolayers of benzenethiol. The intensity of the SERS signal from benzenethiol is correlated to the mean particle size and thus to the fluence. Enhancement factors up to 10(6) with a high reproducibility were reached. Finally we have analyzed the temperature dependence of the SERS effect by recording the intensity of benzenethiol vibrations from 300 to 120 K. The temperature dependence of the SERS effect is discussed with regard to the metal properties.     

Unravelling the Relationship between Raman Enhancement and Photocatalytic Activity on Single Anisotropic Au Microplates

Anisotropic noble‐metal structures are attracting increasing attention because of interesting size‐ and shape‐dependent properties and have emerging applications in the fields of optics and catalysis. However, it remains a significant challenge to overcome chemical contributions and acquire molecular insight into the relationship between Raman enhancement and photocatalytic activity. This study gives visualized experimental evidence of the anisotropic spatial distribution of Raman signals and photocatalytic activity at the level of single nanometer‐thin Au microtriangles and microhexagons. Theoretical simulations indicate an anisotropic spatial distribution and sharpness‐dependent strength of the electric‐field enhancement. Analysis by using statistical surface‐enhanced Raman scattering (SERS) supports this view, that is, Raman enhancement is on the order of corner>edge>face for a single microplate, but SERS measurements at different depths of focus also imply a concentration‐dependent feature of SERS signals, especially at the corners and edges. Similarly, the SERS signals of product molecules in plasmonic photocatalysis also exhibit asymmetrical strengths at different corners of the same microplate. However, by examining the variations in the relative intensities of the SERS peaks, the difference in the photocatalytic activities at the corners, edges, and faces has been successfully calculated and is highly consistent with electric‐field simulations, thus indicating that an increased number of molecules adsorbed at specific sites does not necessarily lead to a higher conversion ratio in noble‐metal photocatalysis. Our strategy weakens the assumed impact of plasmonic local heating and, to a certain extent, excludes the influence of concentration effects and chemical contributions in noble‐metal photocatalysis, thus clearly profiling plasmon‐related characteristics. This study also promises a new research direction to understand the enhancement mechanism of SERS‐active structures.     

Synthesis, characterization, and 3D-FDTD simulation of Ag@SiO2 nanoparticles for shell-isolated nanoparticle-enhanced Raman spectroscopy

Au-seed Ag-growth nanoparticles of controllable diameter (50-100 nm), and having an ultrathin SiO(2) shell of controllable thickness (2-3 nm), were prepared for shell-isolated nanoparticle-enhanced Raman spectroscopy (SHINERS). Their morphological, optical, and material properties were characterized; and their potential for use as a versatile Raman signal amplifier was investigated experimentally using pyridine as a probe molecule and theoretically by the three-dimensional finite-difference time-domain (3D-FDTD) method. We show that a SiO(2) shell as thin as 2 nm can be synthesized pinhole-free on the Ag surface of a nanoparticle, which then becomes the core. The dielectric SiO(2) shell serves to isolate the Raman-signal enhancing core and prevent it from interfering with the system under study. The SiO(2) shell also hinders oxidation of the Ag surface and nanoparticle aggregation. It significantly improves the stability and reproducibility of surface-enhanced Raman scattering (SERS) signal intensity, which is essential for SERS applications. Our 3D-FDTD simulations show that Ag-core SHINERS nanoparticles yield at least 2 orders of magnitude greater enhancement than Au-core ones when excited with green light on a smooth Ag surface, and thus add to the versatility of our SHINERS method.     

Decoration of Diatom Biosilica with Noble Metal and Semiconductor Nanoparticles (<10 nm): Assembly,Characterization, and Applications

Diatom‐templated noble metal (Ag, Pt, Au) and semiconductor (CdTe) nanoparticle arrays were synthesized by the attachment of prefabricated nanoparticles of defined size. Two different attachment techniques—layer‐by‐layer deposition and covalent linking—could successfully be applied. The synthesized arrays were shown to be useful for surface‐enhanced Raman spectroscopy (SERS) of components, for catalysis, and for improved image quality in scanning electron microscopy (SEM).     

Stereoaligned Epitaxial Growth of Single‐Crystalline Platinum Nanowires by Chemical Vapor Transport

Epitaxial Pt nanowire (NW) arrays are synthesized for the first time by a chemical vapor transport method by using a metal halide as a precursor. Here we report that the epitaxial growth direction of NWs can be steered by seed crystal morphology. Octahedral seeds grow into inclined NWs possessing six growth directions, whereas half‐octahedral seeds grow into vertical and horizontal NWs. Interfacial energies between the seed material and the substrate are critical in determining the morphology of seed crystals. We also demonstrate that non‐SERS‐active Pt NWs can show strong surface‐enhanced Raman scattering (SERS) spectra by placing them on Ag films. The active SERS observation would help to elucidate platinum‐catalyzed chemical reactions.     

Controllable Electrochemical Synthesis of Silver Dendritic Nanostructures and Their SERS Properties

Ag dendritic nanostructures were synthesized on fluorine-doped tin oxide covered glass sub-strates by the electrodeposition method. Results demonstrate that the size, diameter, crys-tallinity, and branch density of the Ag dendrites can be controlled by the applied potential,the surfactants and the concentration of AgNO₃. Three kinds of typical silver dendrites were applied as substrates of the surface enhanced Raman scattering (SERS) and one of them was able to clearly detect rhodamine 6G concentrations up to 0.1 nmol/L. The differences of the SERS spectra at these Ag dendrites confirmed that the shapes and interparticle spacings have great effect on Raman enhancement, especially the interparticle spacings.     

3D aluminum/silver hierarchical nanostructure with large areas of dense hot spots for surface‐enhanced raman scattering

Plasmonic nanomaterials possessing large‐volume, high‐density hot spots with high field enhancement are highly desirable for ultrasensitive surface‐enhanced Raman scattering (SERS) sensing. However, many as‐prepared plasmonic nanomaterials are limited in available dense hot spots and in sample size, which greatly hinder their wide applications in SERS devices. Here, we develop a two‐step physical deposition protocol and successfully fabricate 3D hierarchical nanostructures with highly dense hot spots across a large scale (6 × 6 cm²). The nanopatterned aluminum film was first prepared by thermal evaporation process, which can provide 3D quasi‐periodic cloud‐like nanostructure arrays suitable for noble metal deposition; then a large number of silver nanoparticles with controllable shape and size were decorated onto the alumina layer surfaces by laser molecular beam epitaxy, which can realize large‐area accessible dense hot spots. The optimized 3D‐structured SERS substrate exhibits high‐quality detection performance with excellent reproducibility (13.1 and 17.1%), whose LOD of rhodamine 6G molecules was 10^?9 M. Furthermore, the as‐prepared 3D aluminum/silver SERS substrate was applied in detection of melamine with the concentration down to 10^?7 M and direct detection of melamine in infant formula solution with the concentration as low 10 mg/L. Such method to realize large‐area hierarchical nanostructures can greatly simplify the fabrication procedure for 3D SERS platforms, and should be of technological significance in mass production of SERS‐based sensors.     

Photocatalytically Powered Matchlike Nanomotor for Light‐Guided Active SERS Sensing

Surface enhanced Raman spectroscopy (SERS) is a powerful optical sensing technique that can detect analytes of extremely low concentrations. However, the presence of enough SERS probes in the detection area and a close contact between analytes and SERS probes are critical for efficient acquisition of a SERS signal. Presented here is a light‐powered micro/nanomotor (MNM) that can serve as an active SERS probe. The matchlike AgNW@SiO₂ core–shell structure of the nanomotors work as SERS probes based on the shell‐isolated enhanced Raman mechanism. The AgCl tail serves as photocatalytic nanoengine, providing a self‐propulsion force by light‐induced self‐diffusiophoresis. The phototactic behavior was utilized to achieve enrichment of the nanomotor‐based SERS probes for on‐demand biochemical sensing. The results demonstrate the possibility of using photocatalytic nanomotors as active SERS probes for remote, light‐controlled, and smart biochemical sensing on the micro/nanoscale.     

Raman spectroscopy on transition metals

Surface-enhanced Raman spectroscopy (SERS) has developed into one of the most important tools in analytical and surface sciences since its discovery in the mid-1970s. Recent work on the SERS of transition metals concluded that transition metals, other than Cu, Ag, and Au, can also generate surface enhancement as high as 4 orders of magnitude. The present article gives an overview of recent progresses in the field of Raman spectroscopy on transition metals, including experimental, theory, and applications. Experimental considerations of how to optimize the experimental conditions and calculate the surface enhancement factor are discussed first, followed by a very brief introduction of preparation of SERS-active transition metal substrates, including massive transition metal surfaces, aluminum-supported transition metal electrodes, and pure transition metal nanoparticle assembled electrodes. The advantages of using SERS in investigating surface bonding and reaction are illustrated for the adsorption and reaction of benzene on Pt and Rh electrodes. The electromagnetic enhancement, mainly lightning-rod effect, plays an essential role in the SERS of transition metals, and that the charge-transfer effect is also operative in some specific metal–molecule systems. An outlook for the field of Raman spectroscopy of transition metals is given in the last section, including the preparation of well-ordered or well-defined nanostructures, and core-shell nanoparticles for investigating species with extremely weak SERS signals, as well as some new emerging techniques, including tip-enhanced Raman spectroscopy and an in situ measuring technique. Figure Electric-field enhancement of a SERS-active Rh surface decorated with small nanohemispheres     

Noble metal coated single-walled carbon nanotubes for applications in surface enhanced Raman scattering imaging and photothermal therapy

Single-walled carbon nanotubes (SWNTs) with various unique optical properties are interesting nanoprobes widely explored in biomedical imaging and phototherapies. Herein, DNA-functionalized SWNTs are modified with noble metal (Ag or Au) nanoparticles via an in situ solution phase synthesis method comprised of seed attachment, seeded growth, and surface modification with polyethylene glycol (PEG), yielding SWNT-Ag-PEG and SWNT-Au-PEG nanocomposites stable in physiological environments. With gold or silver nanoparticles decorated on the surface, the SWNT-metal nanocomposites gain an excellent concentration and excitation-source dependent surface-enhanced Raman scattering (SERS) effect. Using a near-infrared (NIR) laser as the excitation source, targeted Raman imaging of cancer cells labeled with folic acid (FA) conjugated SWNT-Au nanocomposite (SWNT-Au-PEG-FA) is realized, with images acquired in significantly shortened periods of time as compared to that of using nonenhanced SWNT Raman probes. Owing to the strong surface plasmon resonance absorption contributed by the gold shell, the SWNTs-Au-PEG-FA nanocomposite also offers remarkably improved photothermal cancer cell killing efficacy. This work presents a facile approach to synthesize water-soluble noble metal coated SWNTs with a strong SERS effect suitable for labeling and fast Raman spectroscopic imaging of biological samples, which has been rarely realized before. The SWNT-Au-PEG nanocomposite developed here may thus be an interesting optical theranostic probe for cancer imaging and therapy.     

Surface enhanced fluorescence and Raman imaging of Langmuir-Blodgett azopolymer films

The spectroscopic properties and surface-enhanced spectra of Langmuir-Blodgett (LB) films of methacrylic homopolymer (HPDR13) are presented. It is shown that LB film displays strong fluorescence attributed to the spatial restrictions imposed by its structure. The emission is observed in conjunction with photoisomerization, a process clearly demonstrated by the formation of surface-relief gratings in the LB film [C.R. Mendon?a et al., Macromolecules 32 (1999) 1493]. Surface-enhanced Raman scattering (SERS), Surface-enhanced resonance Raman scattering (SERRS) and surface-enhanced fluorescence (SEF) were observed for LB films of HPDR13 deposited onto silver island films. SERS measurements were also carried out on a sample fabricated with one monolayer LB film deposited onto silver islands followed by one overlayer of silver (LB sandwiched between two layers of silver islands). The polymer interacts very weakly with the metal surface (physisorption), and the enhancement effect is determined by the local electric field enhancement. The strong SERS and SERRS signals were suitable for micro-Raman imaging. Line, area mapping and global images of the LB monolayer on silver island are reported. The transfer ratio in the fabrication of the LB suggests a homogeneous coating of the silver islands, thereby the chemical images show the variation of the SERS intensity due to surface enhancement.     

用于电化学界面研究的共焦显微拉曼光谱技术(英文)

系统地介绍了将共焦显微拉曼光谱系统用于电化学界面研究的方法 ,包括铂电极的粗糙和电化学拉曼电解池的设计 .进行了铂上氢、氧和氯共吸附的拉曼光谱研究 .通过对甲醇氧化过程的现场跟踪 ,提出检测界面区溶液浓度变化和计算溶液 pH值的方法 .实验表明拉曼光谱技术可作为研究实际应用体系的重要工具 .     

Differential SERS activity of gold and silver nanostructures enabled by adsorbed poly(vinylpyrrolidone)

We report that poly(vinylpyrrolidone) (PVP), a common stabilizer of colloidal dispersions of noble metal nanostructures, has a dramatic effect on their surface-enhanced Raman scattering (SERS) activity and enables highly selective SERS detection of analytes of various type and charge. Nanostructures studied include PVP-stabilized Au-Ag nanoshells synthesized by galvanic exchange reaction of citrate-reduced Ag nanoparticles (NPs), as well as solid citrate-reduced Ag and Au NPs, both before and after stabilization with PVP. All nanostructures were characterized in terms of their size, surface plasmon resonance wavelength, surface charge, and chemical composition. While the SERS activities of the parent citrate-reduced Ag and Au NPs are similar for rhodamine 6G (R6G) and 1,2-bis(4-pyridyl)ethylene (BPE) at various pH values, PVP-stabilized nanostructures demonstrate large differences in SERS enhancement factors (EFs) between these analytes depending on their chemical nature and protonation state. At pH values higher than BPE's pK(a2) of 5.65, where the analyte is largely unprotonated, the PVP-coated Au-Ag nanoshells showed a high SERS EF of >10(8). In contrast, SERS EFs were 10(3)- to 10(5)-fold lower for the protonated form of BPE at lower pH values, or for the usually highly SERS-active cationic R6G. The differential SERS activity of PVP-stabilized nanostructures is a result of discriminatory binding of analytes within-adsorbed PVP monolayer and a subsequent increase of analyte concentration at the nanostructure surface. Our experimental and theoretical quantum chemical calculations show that BPE binding with PVP-stabilized Au-Ag nanoshells is stronger when the analyte is in its unprotonated form as compared to its cationic, protonated form at a lower pH.     

Surface enhanced Raman scattering based on silver dendrites substrate

A simple method of the reduction of AgNO3 by copper foil in aqueous medium was used to prepare silver dendrites, which can be used as a novel good reproducible surface enhanced Raman scattering (SERS) active substrate. The SERS spectra of 4-pyridinethiol on this novel substrate reflected the different SERS activities on the minuteness and strong Ag dendrites. The electromagnetic coupling enhancement and chemical enhancement mechanisms are used to explain the SERS effect.