Simultaneous Determination of Lead,Copper, and Mercury Free from Macromolecule Contaminants by Square Wave Stripping Voltammetry

Abstract

A novel approach for the voltammetric determination of Pb²⁺, Cu²⁺, and Hg²⁺ in the presence of macromolecule contaminants was developed. An Au nanoparticles array was directly electrodeposited onto the gold electrode surface followed by a further modification of a mercaptoethanesulfonate (MES) monolayer. Square wave stripping voltammetry (SWSV) of Pb²⁺, Cu²⁺, and Hg²⁺ was performed on the doubly modified electrode. The electrodeposited gold nanoparticles provided a significantly improved sensitivity. Simultaneously, the MES monolayer efficiently prevented the macromolecules accessing the electrode surface. Compared with the bare gold electrode, the doubly modified electrode has the ability to detect metal ions in the presence of macromolecule contaminants, even when their concentration reach 100 ppm. Under the optimal conditions, the detection limits of 0.16, 0.15, and 0.14 ppb for Pb²⁺, Cu²⁺, and Hg²⁺ were obtained, respectively. The calibration graphs were linear in the concentration range of 1–100 ppb. The results of the analysis of a real metallurgy wastewater sample were reported. The electrode system has a great potential for the direct determination of trace metals in the complex environment and biological samples.     

CC Bonding of Graphene Oxide on 4‐Aminophenyl Modified Gold Electrodes towards Simultaneous Detection of Heavy Metal Ions

This paper studied the electrochemical sensors based on C? C bonding of graphene oxide (GO) on π‐conjugated aromatic group modified gold electrodes for simultaneous detection of heavy metal ions. For comparison, another sensing interface Au‐Ph‐NH‐CO‐GO, in which GO was modified to Au‐Ph‐NH₂ interfaces by amide bonding. On the basis of the principle of heavy metal ions complexation with oxygenated species on GO, the fabricated sensing interfaces were used for the simultaneous determination of Pb²⁺, Cu²⁺ and Hg²⁺. The performance of two sensing interfaces for simultaneous detection of three metal ions was compared. Au‐Ph‐GO sensing interface demonstrated higher sensitivity and better repeatability than Au‐Ph‐NH‐CO‐GO sensing interface.     

Anodic Stripping Voltammetric Determination of Mercury(II) in Water Using a 4‐Tert‐Butyl‐1‐(Ethoxycarbonylmethoxy)Thiacalix[4]Arene Modified Glassy Carbon Electrode

A glassy carbon electrode coated the film of 4‐tert‐butyl‐1‐(ethoxycarbonylmethoxy)thiacalix[4]arene is designed for the determination of trace amounts of Hg²⁺. Compared with bare glassy carbon electrode, the modified electrode can improve the measuring sensitivity of Hg²⁺. Under the optimum experimental condition, the modified electrode in 0.1 mol L^?1 H₂SO₄ + 0.01 mol L^?1 KCl solution shows a linear voltammetric response in the range of 8.0 × 10^?9 ～ 3.0 × 10^?6 mol L^?1 with detection limit 5.0 × 10^?9 mol L^?1 for Hg²⁺. The high sensitivity, selectivity, and stability of modified electrode also prove its practical application for a simple, rapid and economical determination of Hg²⁺ in water samples.     

Electrochemical aptamer sensor for highly sensitive detection of mercury ion with Au/Pt@carbon nanofiber‐modified electrode

In this paper, an electrochemical aptamer sensor was proposed for the highly sensitive detection of mercury ion (Hg²⁺). Carbon nanofiber (CNF) was prepared by electrospinning and high‐temperature carbonization, which was used for the loading of platinum nanoparticles (PtNPs) by the hydrothermal method. The Pt@CNF nanocomposite was modified on the surface of carbon ionic liquid electrode (CILE) to obtain Pt@CNF/CILE, which was further decorated by gold nanoparticles (AuNPs) through electrodeposition to get Au/Pt@CNF/CILE. Self‐assembling of the thiol‐based aptamer was further realized by the formation of Au‐S bond to get an electrochemical aptamer sensor (Aptamer/Au/Pt@CNF/CILE). Due to the specific binding of aptamer probe to Hg²⁺ with the formation of T‐Hg²⁺‐T structure, a highly sensitive quantitative detection of Hg²⁺ could be achieved by recording the changes of current signal after reacting with Hg²⁺ within the concentration range from 1.0 × 10^?15 mol/L to 1.0 × 10^?6 mol/L and the detection limit of 3.33 × 10^?16 mol/L (3σ). Real water samples were successfully analyzed by this method.     

Exploring the interactions between gold nanoparticles and analytes through surface‐assisted laser desorption/ionization mass spectrometry

Surface‐assisted laser desorption/ionization mass spectrometry (SALDI‐MS) is applied to provide strong evidence for the chemical reactions of functionalized gold nanoparticles (Au NPs) with analytes – Hg²⁺ ions induced MPA?Au NPs aggregation in the presence of 2,6‐pyridinedicarboxylic acid (PDCA) and H₂O₂ induced fluorescence quenching of 11‐MUA?Au NDs. PDCA‐Hg²⁺‐MPA coordination is responsible for Au NPs aggregation, while the formation of 11‐MUA disulfide compounds that release into the bulk solution is responsible for H₂O₂‐induced fluorescence quenching. In addition to providing information about the chemical structures, SALDI‐MS is also selective and sensitive for the detection of Hg²⁺ ions and H₂O₂. The limits of detection (LODs) for Hg²⁺ ions and H₂O₂ by SALDI‐MS were 300 nM and 250 µM, respectively. The spot‐to‐spot variations in the two studies were both less than 18% (50 sample spots). Our results reveal that SALDI‐MS can be used to study analyte‐induced changes in the surface properties of nanoparticles. Copyright © 2010 John Wiley & Sons, Ltd.     

Development of a Sensor Based on Poly(1,2-diaminoanthraquinone) for Individual and Simultaneous Determination of Mercury (II) and Bismuth (III)

Contamination of natural water by mercury (Hg²⁺) and bismuth (Bi³⁺) metal ions have been extensively studied due to their toxic effects. A validated square-wave anodic stripping voltammetry (SW-ASV) method for determining Bi³⁺ and Hg²⁺ ions individually and simultaneously is described. A new electrochemical sensor was constructed using a gold (Au) electrode that has been modified with poly(1,2-diaminoanthraquinone) (p-1,2-DAAQ). Scanning electron microscopy, cyclic voltammetry, and electrochemical impedance spectroscopy were used to characterize the p-1,2-DAAQ/Au modified electrode. Factors such as the polymer film thickness, electrolyte, square wave parameters and preconcentration conditions were optimized to improve the performance of the modified Au electrode. Good linear responses were achieved in the concentration ranges of 1–200 μg L⁻¹ and 1–50 μg L⁻¹ forBi³⁺ and Hg²⁺, respectively, and the limits of detection were 0.27 μg L⁻¹ (Bi³⁺) and 0.29 μg L⁻¹ (Hg²⁺). The interference study results illustrated the high selectivity of the modified electrode for detection of Bi³⁺ and Hg²⁺. The proposed SW-ASV method was successfully applied for Bi³⁺ and Hg²⁺analyses in different real water samples.     

Anodic Stripping Voltammetric Detection of Arsenic(III) at Gold Nanoparticle‐Modified Glassy Carbon Electrodes Prepared by Electrodeposition in the Presence of Various Additives

The simple, fast and highly sensitive anodic stripping voltammetric detection of As(III) at a gold (Au) nanoparticle‐modified glassy carbon (GC) (nano‐Au/GC) electrode in HCl solution was extensively studied. The Au nanoparticles were electrodeposited onto GC electrode using chronocoulometric technique via a potential step from 1.1 to 0 V vs. Ag|AgCl|NaCl (sat.) in 0.5 M H₂SO₄ containing Na[AuCl₄] in the presence of KI, KBr, Na₂S and cysteine additives. Surfaces of the resulting nano‐Au/GC electrodes were characterized with cyclic voltammetry. The performances of the nano‐Au/GC electrodes, which were prepared using different concentrations of Na[AuCl₄] (0.05–0.5 mM) and KI additive (0.01–1.0 mM) at various deposition times (10–30 s), for the voltammetric detection of As(III) were examined. After the optimization, a high sensitivity of 0.32 mA cm^?2 μM^?1 and detection limit of 0.024 μM (1.8 ppb) were obtained using linear sweep voltammetry.     

Electrochemical Oxidation of Methionine Mediated by a Fullerene‐C60 Modified Gold Electrode

The usefulness of a C₆₀‐fullerene modified gold (Au) electrode in mediating the oxidation of methionine in the presence of potassium ions electrolyte has been demonstrated. During cyclic voltammetry, an oxidation peak of methionine appearing at +1.0 V vs. Ag/AgCl was observed. The oxidation current of methionine is enhanced by about 2 times using a C₆₀ modified gold electrode. The current enhancement is significantly dependent on pH, temperature and C₆₀ dosage. Calibration plot reveals linearity of up to 0.1 mM with a current sensitivity of close to 50 mA L mol^?1 and detection limit of 8.2×10^?6 M. The variation of scan rate study shows that the system undergoes diffusion‐controlled process. Diffusion coefficient and rate constant of methionine were determined using hydrodynamic method (rotating disk electrode) with values of 1.11×10^?5 cm² s^?1 and 0.0026 cm s^?1 respectively for unmodified electrode while the values of diffusion coefficient and rate constant of methionine using C₆₀ modified Au electrode are 5.7×10^?6 cm² s^?1 and 0.0021 cm s^?1 respectively.     

Naphthalene Diimide Carrying Two Cysteine Termini at Both Imide Linkers as a Molecular Staple

Naphthalene diimide ( 1 ) carrying cysteines at the termini of amide substituents were synthesized to act as a molecular staple of double stranded DNA. Since 1 is able to bind to double stranded DNA with threading intercalation, the complex of 1 with double stranded DNA can be topologically immobilized on a gold surface through the S? Au linkage as confirmed by cyclic voltammetric experiment. Ferrocenyl‐double stranded 23‐mertic oligonucleotide, dsFcODN, was immobilized on gold electrode with 1.0×10¹² molecules cm^?2 when electrode was treated with 2.0 µM dsFcODN and 4.0 µM 1 for 1 h at room temperature. The coverage density was similar to that obtained for the terminal thiol‐modified oligonucleotide. Compound 1 was applied to detect the 321‐meric PCR product of P. gingivalis, which is important in the diagnosis of periodontal disease. This experiment, coupled with the use of ferrocenylnaphthalene diimide, FND as electrochemical indicator for double stranded DNA, resulted in quantitative detection of PCR product within the range of 10 pg µL^?1–10 ng µL^?1 (15 nM–15 µM). The 1 and FND established a simple and rapid detection method of double stranded PCR product with a detection limit of 10 pg µL^?1 (15 nM).     

Anodic Stripping Voltammetric Determination of Lead（Ⅱ） Using Glassy Carbon Electrode Modified with Novel Calix[4] arene

A new glassy carbon electrode modified with novel calix[4]‐arene derivative was prepared and then applied to the selective recognition of lead ion in aqueous media by cyclic and square wave voltammetry. A new anodic stripping peak at ? 0.92 V (vs. Ag/Ag⁺) in square wave voltammogram can be obtained by scanning the potential from ? 1.5 to ? 0.6 V, of which the peak current is proportional to the concentration of Pb²⁺. The modified electrode in 0.1 mol/L HNO₃ solution showed a linear voltammetric response in the range of 2.0 × 10–⁸–1.0 × 10–⁶ mol/L and a detection limit of 6.1 × 10–⁹ mol/L. In the modified glassy carbon electrode no significant interference occurred from alkali, alkaline and transition metal ions except Hg²⁺, Ag⁺ and Cu²⁺ ions, which can be eliminated by the addition of KSCN. The proposed method was successfully applied to determine lead in aqueous samples.     

Electrodeposited nanogold decorated graphene modified carbon ionic liquid electrode for the electrochemical myoglobin biosensor

In this paper, a carbon ionic liquid electrode (CILE) was fabricated using ionic liquid 1-hexylpyridinium hexafluorophosphate as modifier, which was further in situ electrodeposited with graphene (GR) and gold nanoparticles step by step to get an Au/GR nanocomposite modified CILE. Myoglobin (Mb) was further immobilized on the Au/GR/CILE surface with Nafion film to get the modified electrode denoted as Nafion/Mb/Au/GR/CILE. Cyclic voltammetric experiments indicated that a pair of well-defined quasi-reversible redox peaks appeared in pH 3.0 phosphate buffer solution with the formal potential (E ^0′) located at ?0.197 V (vs. saturated calomel electrode), which was the typical characteristics of Mb heme Fe(III)/Fe(II) redox couples. Thus, the direct electron transfer rate between Mb and the modified electrode was promoted due to the high conductivity and increased surface area of Au/GR nanocomposite present on electrode surface. Based on the cyclic voltammetric data, the electrochemical parameters of Mb on the modified electrode were calculated. The Mb-modified electrode showed excellent electrocatalytic activities towards the reduction of trichloroacetic acid and H₂O₂ with wider linear range and lower detection limit. Using GR and Au nanoparticles modified CILE, a new third-generation electrochemical Mb biosensor was constructed with good stability and reproducibility.     

Voltammetric determination of mercury (II) in aqueous media using glassy carbon electrodes modified with novel calix[4]arene

A novel calix[4]arene derivative containing benzothiazole group was coated on glassy carbon electrode (GCE) and then applied to the recognition of mercury ion. Cyclic and square wave voltammetric results showed that the modified electrode selectively recognizes Hg²⁺ ion in aqueous media. A new anodic stripping peak at −0.3 V (vs. Ag/Ag⁺) can be obtained by scanning the potential from −0.6 to 0.6 V, and the peak currents are proportional to the Hg²⁺ concentration. The modified electrode in a 0.1 M H₂SO₄+0.01 M NaCl solution shows linear voltammetric response in the range of 25-300 μg l⁻¹ and detection limit of 5 μg l⁻¹ (ca. 2.5×10⁻⁸ M). This modified GCE does not present any significant interference from alkali, alkaline and transition metal ions except for Pb²⁺, Ag⁺ and Cu²⁺ ions. Only 500, 50 and 100-fold molar excess of Pb²⁺, Ag⁺ and Cu²⁺ ions, respectively, can lead to voltammetric response comparable with that of Hg²⁺. The proposed method was successfully applied to determine mercury in natural water.     

Electrochemical Detection of Catechol on Boron‐doped Diamond Electrode Modified with Au/TiO2 Nanorod Composite

Au/TiO₂ nanorod composites with different ratios of [TiO₂]:[Au] have been prepared by chemically reducing AuCl₄^‐ on the positively charged TiO₂ nanorods surface and used to modify boron‐doped diamond (BDD) electrodes. The electrochemical behaviors of catechol on the bare and different Au/TiO₂ nanorod composites‐modified BDD electrodes are studied. The cyclic voltammetric results indicate that these different Au/TiO₂ nanorod composites‐modified BDD electrodes can enhance the electrocatalytic activity toward catechol detection, as compared with the bare BDD electrode. Among these different conditions, the Au/TiO₂‐BDD3 electrode (the ratio of [TiO₂]:[Au] is 27:1) is the most choice for catechol detection. The electrochemical response dependences of the Au/TiO₂‐BDD3 electrode on pH of solution and the applied potential are studied. The detection limit of catechol is found to be about 1.4 × 10^‐6 M in a linear range from 5 × 10^‐6 M to 200 × 10^‐6 M on the Au/TiO₂‐BDD3 electrode.     

Target-induced formation of gold amalgamation on DNA-based sensing platform for electrochemical monitoring of mercury ion coupling with cycling signal amplification strategy

Heavy metal ion pollution poses severe risks in human health and environmental pollutant, because of the likelihood of bioaccumulation and toxicity. Driven by the requirement to monitor trace-level mercury ion (Hg²⁺), herein we construct a new DNA-based sensor for sensitive electrochemical monitoring of Hg²⁺ by coupling target-induced formation of gold amalgamation on DNA-based sensing platform with gold amalgamation-catalyzed cycling signal amplification strategy. The sensor was simply prepared by covalent conjugation of aminated poly-T₍₂₅₎ oligonucleotide onto the glassy carbon electrode by typical carbodiimide coupling. Upon introduction of target analyte, Hg²⁺ ion was intercalated into the DNA polyion complex membrane based on T–Hg²⁺–T coordination chemistry. The chelated Hg²⁺ ion could induce the formation of gold amalgamation, which could catalyze the p-nitrophenol with the aid of NaBH₄ and Ru(NH₃)₆³⁺ for cycling signal amplification. Experimental results indicated that the electronic signal of our system increased with the increasing Hg²⁺ level in the sample, and has a detection limit of 0.02 nM with a dynamic range of up to 1000 nM Hg²⁺. The strategy afforded exquisite selectivity for Hg²⁺ against other environmentally related metal ions. In addition, the methodology was evaluated for the analysis of Hg²⁺ in spiked tap-water samples, and the recovery was 87.9–113.8%.     

Immunosensors Based on Layer‐by‐Layer Self‐Assembled Au Colloidal Electrode for the Electrochemical Detection of Antigen

Colloidal Au particles have been deposited on the gold electrode through layer‐by‐layer self‐assembly using cysteamine as cross‐linkers. Self‐assembly of colloidal Au on the gold electrode resulted in an easier attachment of antibody, larger electrode surface and ideal electrode behavior. The redox reactions of [Fe(CN)₆]^4?/[Fe(CN)₆]^3? on the gold surface were blocked due to antibody immobilization, which were investigated by cyclic voltammetry and impedance spectroscopy. The interaction of antigen with grafted antibody recognition layers was carried out by soaking the modified electrode into a phosphate buffer at pH 7.0 with various concentrations of antigen at 37 °C for 30 min. Further, an amplification strategy to use biotin conjugated antibody was introduced for improving the sensitivity of impedance measurements. Thus, the sensor based on this immobilization method exhibits a large linear dynamic range, from 5–400 μg/L for detection of Human IgG. The detection limit is about 0.5 μg/L.     

Electrode Modified with Langmuir–Blodgett (LB) Film of Calixarenes for Preconcentration and Stripping Analysis of Hg(II)

A new type of current sensor, Langmuir–Blodgett (LB) film of calixarene on the surface of glassy carbon electrode (GCE) was prepared for determination of mercury by anodic stripping voltammetry (ASV). An anodic stripping peak was obtained at 0.15 V (vs. SCE) by scanning the potential from ?0.6 to +0.6 V. Compared with a bare GCE, the LB film coated electrode greatly improves the sensitivity of measuring mercury ion. The fabricated electrode in a 0.1 M H₂SO₄+0.01 M HCl solution shows a linear voltammetric response in the range of 0.07–40 μg L^?1 and detection limit of 0.04 μg L^?1 (ca. 2×10^?10 M). The high sensitivity, selectivity, and stability of this LB film modified electrode demonstrates its practical application for a simple, rapid and economical determination of Hg²⁺ in a water sample.     

Electrochemical Fabrication of Prussian Blue Nanocube‐decorated Electroreduced Graphene Oxide for Amperometric Sensing of NADH

In this study, Prussian blue (PB) film on the electroreduced graphene oxide (ERGO)‐modified Au electrode surface (ERGO/PB) is easily prepared by means of cyclic voltammetric technique in the mixture of K₃Fe(CN)₆ and FeCl₃. Its electrochemical behaviors for NADH biosensor are studied. The structural and morphological characters of modified electrode material are analyzed with using of XPS, XRD, Raman, EDS, and SEM techniques. ERGO/PB hybrid nanocomposite for NADH biosensor is exhibited to the higher catalytic effect (linear range from 1.0 to 100 μM, detection limit of 0.23 μM at S/N=3) compared to naked Au, ERGO‐modified Au, and PB‐modified Au electrodes. In addition to, ERGO/PB electrode was used to voltammetric and amperometric detection of H₂O₂. ERGO/PB electrodes also showed the same behavior as the NADH sensor. This ERGO/PB‐modified electrode supplied a simple, new, and low‐cost route for amperometric sensing of both NADH and H₂O₂.     

Modification of gold electrode by self-assembled 2-mercapto benzothiazole for the determination of Hg2+

An electrochemical method was developed for the determination of mercury using polycrystalline gold electrode modified by self-assembled monolayers (SAMs) of 2-mercaptobenzothiazole (MBTH). Morphological and electrochemical characterisation of the self-assembled structure of MBTH was performed using atomic force microscopy (AFM) and electrochemical impedance spectroscopy (EIS) measurements. The monolayer of MBTH has shown high affinity for Hg²⁺. The limit of detection for the determination of Hg²⁺ using the MBTH SAMs modified gold electrode was obtained as 0.421 μg L^?1. The pre-concentration of Hg²⁺ at open circuit potential is beneficial for the onsite monitoring of mercury concentration in water samples.     

Colloid Au-enhanced DNA immobilization for the electrochemical detection of sequence-specific DNA

We use colloidal Au to enhance the DNA immobilization amount on a gold electrode and ultimately lower the detection limit of our electrochemical DNA biosensor. Self-assembly of approximately 16-nm diameter colloidal Au onto a cysteamine modified gold electrode resulted in an easier attachment of an oligonucleotide with a mercaptohexyl group at the 5′-phosphate end, and therefore an increased capacity for nucleic acid detection. Quantitative results showed that the surface densities of oligonucleotides on the Au colloid modified gold electrode were approximately (1–4)×10¹⁴ molecules cm⁻². Hybridization was induced by exposure of the ssDNA-containing gold electrode to ferrocenecarboxaldehyde labeled complementary ssDNA in solution. The detection limit is 5×10⁻¹⁰ mol l⁻¹ of complementary ssDNA, which is much lower than our previous electrochemical DNA biosensors. The Au nanoparticle films on the Au electrode provide a novel means for ssDNA immobilization and sequence-specific DNA detection.     

Differential Pulse Voltammetric Determination of Selenocystine Using Selenium‐gold Film Modified Electrode

Differential pulse voltammetric determination of selenocystine (SeC) using selenium‐gold film modified glassy carbon electrode ((Se‐Au)/GC) is presented. In 0.10 mol?L^?1 KNO₃ (pH 3.20) solution, SeC yields a sensitive reduction peak at ?740 mV on (Se‐Au)/GC electrode. The peak current has a linear relationship with the concentration of SeC in the range of 5.0×10^?8–7.0×10^?4 mol?L^?1, and a 3σ detection limit of SeC is 3.0×10^?8 mol?L^?1. The relative standard deviation of the reduction current at SeC concentration of 10^?6 mol?L^?1 is 3.88% (n=8) using the same electrode, and 4.19% when using three modified electrodes prepared at different times. The content of SeC in the selenium‐enriched yeast and selenium‐enriched tea is determined. The total selenium in ordinary or selenium‐enriched tea is determined by DAN fluorescence method. The results indicate that in selenium‐enriched yeast about 20% of total selenium is present as SeC and in selenium‐enriched tea SeC is the major form of selenoamino acids. The total selenium content in selenium‐enriched tea soup is 0.09 μgSe/g accounting by 7% compared with that in selenium‐enriched tea. Hence, only a little amount of selenium is utilized by drinking tea, and most selenium still stay in tealeaf. Uncertainty are 22.4% and 16.1% for determination of SeC in selenium‐enriched yeast and selenium‐enriched tea by differential pulse voltammetry (DPV) on (Se‐Au)/GC electrode, respectively.