Oxidative Coupling of Methane over Na-W-Mn/Si0_2 Catalysts at Elevated Pressures

Na-Mn-W/SiO2 catalysts were studied for the oxidative coupling of methane (OCM) in a micro fixed bed reactor made of stainless steel reactor at elevated pressures. The effect of operating conditions, such as GHSV, pressure, temperature and CH4/O2 ratio on the catalytic performance of OCM was investigated. The C2+ selectivity of 80.3% was obtained at a CH4 conversion of 16.1% at 750℃, 1.5×105h-1 GHSV, and 0.6 MPa. Also, there is a small output of C3 and C4 hydrocarbons in the tail gas. The results show that unfavorable effects due to elevated pressure can be overcome by increasing GHSV, and the OCM reaction is strongly dependent on the operating conditions at elevated pressures, particularly GHSV and the CH4/O2 ratio.     

Effects of operating parameters on oxidative coupling of methane over Na-W-Mn/SiO2 catalyst at elevated pressures

The effects of operating parameters on oxidative coupling of methane (OCM) over Na-W-Mn/SiO2 catalyst have been studied at elevated pressures of 0.2, 0.3 and 0.4 MPa under low gaseous hourly space velocity (GHSV) and low temperature conditions. Experimental results show that when the operating pressure is increased, C2+ yield slightly decreases, while the maximum ratio of ethylene to ethane remains unchanged. Moreover, it has been found empirically that increase of pressure does not affect the catalyst behavior permanently, the catalyst recovers its original low pressure performance without hysteresis behavior by reducing the pressure. Under the investigated conditions, when oxygen is completely consumed, the increase of GHSV leads to improvement in C2 selectivity, while C3+ and COx selectivities decrease slightly. The C2+ selectivity increases by increase of nitrogen diluent in the feed, but the C3+ hydrocarbons selectivities decrease with increase of nitrogen since it is possible that further dilution at high pressure may reduce the probability of collision between CH3 and C2+ hydrocarbons. During the stability test at high pressure, the catalyst performance remains unchanged throughout the 20 h running. The fresh and used catalysts were characterized using XRD, SEM and N2 adsorption-desorption methods. It was found that the phase transformation of the support from α-cristobalite to tridymite and quartz does not have obvious effect on catalyst performance at high pressure.     

Effects of ammonium exchange and Si/Al ratio on the conversion of methanol to propylene over a novel and large partical size ZSM-5

One type of ZSM-5 zeolite with large partical size was prepared and characterized by XRD, SEM, N2 adsorption-desorption, XRF, Py-IR and NH3-TPD techniques. Effects of ammonium exchange and SiO2/Al2O3 molar ratios on the reaction of methanol to propylene (MTP) over Na-ZSM-5 and H-ZSM-5 zeolites have been studied in a fixed-bed flow reactor under the operating conditions of T = 500 °C, P = 1 atm, and WHSV = 6 h-1. Ammonium exchange led to a rapid decrease in Na content for Na-ZSM-5 zeolite. The reaction results indicated that Na-ZSM-5 and H-ZSM-5 with different SiO2/Al2O3 molar ratios all exhibited high activity for methanol conversion. Ammonium exchange and the decreased SiO2/Al2O3 molar ratio of ZSM-5 zeolite led to an increase both in strong acid sites and weak acid sites. Na-ZSM-5 with high SiO2/Al2O3 molar ratio was favorable for the formation of propylene. The highest propylene selectivity (45.9%) was obtained over Na-ZSM-5 zeolite catalyst with SiO2/Al2O3 molar ratio of 220.     

Comparison of dry reforming of methane in low temperature hybrid plasma-catalytic corona with thermal catalytic reactor over Ni/γ-Al2O3

In the current study,the hybrid effect of a corona discharge and γ-alumina supported Ni catalysts in CO2 reforming of methane is investigated.The study includes both purely catalytic operation in the temperature range of 923-1023K,and hybrid catalytic-plasma operation of DC corona discharge reactor at room temperature and ambient pressure.The effect of feed flow rate,discharge power and Ni/γ-Al2O3 catalysts are studied.When CH4/CO2 ratio in the feed is 1/2,the syngas of low H2/CO ratio at about 0.56 is obtained,which is a potential feedstock for synthesis of liquid hydrocarbons.Although Ni catalyst is only active above 573K,presence of Ni catalysts in the cold corona plasma reactor(T≤523K) shows promising increase in the conversions of methane and carbon dioxide.When Ni catalysts are used in the plasma reaction,H2/CO ratios in the products are slightly modified,selectivity to CO increases whereas fewer by-products such as hydrocarbons and oxygenates are formed.     

OXIDATIVE COUPLING OF METHANE OVER Mn_2O_3-Na_2WO_4/SiO_2 CATALYST IN THE ABSENCE OF DILUTE GAS

The oxidative coupling of methane over Mn2O3-Na2WO4/SiO2 catalyst has been investigated in the absence of dilute gas. 16.4% of C2 yield and 80.4% of the selectivity to C2 hydrocarbons were obtained at CH4/O2 = 8.5/1.5. The effect of flow rate on the selectivity to C2 hydrocarbons and CH4 conversion was different under the reaction condition of different ratio of CH4 to oxygen. The flow rate had a more remarkable effect on the selectivity at the lower ratio of methane to oxygen. The addition of steam into the reaction gas can increase C2 yield to some extent, but that of HC1 decrease the selectivity to C2 hydrocarbons.     

Production of propylene from an unconventional metathesis of ethylene and 2-pentene over Re2O7/SiO2-Al2O3 catalysts

An unconventional metathesis of ethylene and 2-pentene over Re2O7/SiO2-Al2O3 catalysts has been studied as an alternative route for the production of propylene. Complete conversion of 2-pentene and propylene yield as high as 88 wt% were obtained under mild reaction conditions at 35°C and atmospheric pressure. Unlike the conventional metathesis of ethylene and 2-butenes in which isomerization is a competing side reaction, the isomerization of 1-butene product from the unconventional metathesis of ethylene and 2-pentene to 2-butenes can further react with excess ethylene in the feed, resulting in additional increase in propylene yield. The secondary metathesis reaction was found to be favored under ethylene/2-pentene (E/2P) molar ratio 3 and gas hourly space velocity (GHSV) 1000 h-1 at the reaction temperature of 35°C. No catalyst deactivation was observed during the 455 min time-on-stream under the selected reaction conditions.     

Experimental investigation of fluidized-bed reactor performance for oxidative coupling of methane

Performance of the oxidative coupling of methane in fluidized-bed reactor was experimentally investigated using Mn-Na2WO4/SiO2,La2O3/CaO and La2O3-SrO/CaO catalysts.These catalysts were found to be stable,especially Mn-Na2WO4/SiO2 catalyst.The effect of sodium content of this catalyst was analyzed and the challenge of catalyst agglomeration was addressed using proper catalyst composition of 2%Mn2.2%Na2WO4/SiO2.For other two catalysts,the effect of Lanthanum-Strontium content was analyzed and 10%La2O 3-20%SrO/CaO catalyst was found to provide higher ethylene yield than La2O3/CaO catalyst.Furthermore,the effect of operating parameters such as temperature and methane to oxygen ratio were also reviewed.The highest ethylene and ethane (C2) yield was achieved with the lowest methane to oxygen ratio around 2.40.5% selectivity to ethylene and ethane and 41% methane conversion were achieved over La2O3-SrO/CaO catalyst while over Mn-Na2WO4 /SiO2 catalyst,40% and 48% were recorded,respectively.Moreover,the consecutive effects of nitrogen dilution,ethylene to ethane production ratio and other performance indicators on the down-stream process units were qualitatively discussed and Mn-Na2WO4/SiO2 catalyst showed a better performance in the reactor and process scale analysis.     

Thermodynamic analysis of mixed and dry reforming of methane for solar thermal applications

Thermodynamic analysis of the reforming of methane with carbon dioxide alone ("dry reforming") and with carbon dioxide and steam together ("mixed reforming") is performed as part of a project which investigates the suitability of these endothermic reactions for the storage of solar thermal energy. The Gibbs free energy minimization method was employed to identify thermodynamically optimal operating conditions for dry reforming as well as mixed reforming with a desired H2/CO molar ratio of 2. The non-stoichiometric equilibrium model was developed using FactSage software to conduct the thermodynamic calculations for carbon formation, H2/CO ratio, CH4 conversion and H2 yield as a function of reaction temperature, pressure and reactant molar ratios. Thermodynamic calculations demonstrate that in the mixed reforming process, optimal operating conditions in a carbon-free zone are under H2O/CH4 /CO2 =1.0/1.0/0.5, p = 1 to 10 bar and T = 800 to 850℃ for the production of syngas with a H2 /CO molar ratio of 2. Under the optimal conditions, the maximum H2 yield of 88.0% is achieved at 1 bar and 850℃ with a maximum CH4 conversion of 99.3%. In the dry reforming process, a carbon formation regime is always present at a CO2/CH4 molar ratio of 1 for T = 700 1000℃ and p = 1-30 bar, whereas a carbon-free regime can be obtained at a CO2/CH4 molar ratio greater than 1.5 and T≥800℃.     

Modeling of Fischer-Tropsch Synthesis in a Slurry Reactor with Water Permeable Membrane

Fischer-Tropsch synthesis is an important chemical process for the production of liquid fuels and olefins. In recent years, the abundant availability of natural gas and the increasing demand of olefins, diesel, and waxes have led to a high interest to further develop this process. A mathematical model of a slurry membrane reactor used for syngas polymerization was developed to simulate and compare the maximum yields and operating conditions in the reactor with that in a conventional slurry reactor. The carbon polymerization was studied from a modeling point of view in a slurry reactor with a water permeable membrane and a conventional slurry reactor. Simulation results show that different parameters affect syngas conversion and carbon product distribution, such as the hydrogen to carbon monoxide ratio, and the membrane parameters such as membrane permeance.     

Effect of O2 and H2O on the tri-reforming of the simulated biogas to syngas over Ni-based SBA-15 catalysts

A series of Ni/SBA-15 catalysts with Ni contents from 7.5 wt% to 15 wt% were prepared by impregnation method. The effect of O2 and H2O on the combined reforming of the simulated biogas to syngas was investigated in a continuous flow fixed-bed micro-reactor. The stability of the catalyst was tested at 800 ℃. The results indicated that 10 wt%Ni/SBA-15 catalyst exhibited the highest catalytic activities for the combined reforming of the simulated biogas to syngas. Under the reaction conditions of the feed gas molar ratios CH4/CO2/O2/H2O = 2/1/0.6/0.6, GHSV = 24000 ml•g{cat}-1\cdoth-1 and the reaction temperatureT = 800 ℃, the conversions of CH4 and CO2 were 92.8% and 76.3%, respectively, and the yields of CO and H2 were 99.0% and 82.0%, respectively. The catalytic activities of the catalyst did not decrease obviously after 100 h reaction time on stream.     

Effect of Ni Loading and Reaction Conditions on Partial Oxidation of Methane to Syngas

The partial oxidation of methane to synthesis gas is studied in this paper over Ni/Al2O3 catalysts under atmospheric pressure. The effects of Ni loading on the activity and stability of catalysts with 5 mm α-Al2O3 and θ-Al2O3 pellets as supports were measured in a continuous fixed bed reactor. It is found that the optimum Ni loading is 10%. And the effect of reaction conditions on partial oxidation of methane is also studied. The methane conversion and CO selectivity increase with the increase of the reaction temperature and the space velocity on 10%Ni/α-Al2O3 catalysts. The best CH4/O2 mole ratio is 2 for CO selectivity, and the optimum space velocity is 5.4x105 h-1.     

Effect of Al2O3 Binder on the Precipitated Iron-Based Catalysts for Fischer-Tropsch Synthesis

A series of iron-based Fischer-Tropsch synthesis (FTS) catalysts incorporated with Al2O3 binder were prepared by the combination of co-precipitation and spray drying technology. The catalyst samples were characterized by using N2 physical adsorption, temperature-programmed reduc-tion/desorption (TPR/TPD) and Mossbauer effect spectroscopy (MES) methods. The characterization results indicated that the BET surface area increases with increasing Al2O3 content and passes through a maximum at the Al2O3/Fe ratio of 10/100 (weight basis). After the point, it decreases with further increase in Al2O3 content. The incorporation of AI2O3 binder was found to weaken the surface basicity and suppress the reduction and carburization of iron-based catalysts probably due to the strong K-Al2O3 and Fe-Al2O3 interactions. Furthermore, the H2 adsorption ability of the catalysts is enhanced with increasing Al2O3 content. The FTS performances of the catalysts were tested in a slurry-phase continuously stirred tank reactor (CSTR) under the reaction conditions of 260℃, 1.5 MPa, 1000 h-1 and molar ratio of H2/CO 0.67 for 200 h. The results showed that the addition of small amounts of Al2O3 affects the activity of iron-based catalysts to a little extent. However, with further increase of Al2O3 content, the FTS activity and water gas shift reaction (WGS) activity are decreased severely. The addition of appropriate Al2O3 do not affect the product selectivity, but the catalysts incorporated with large amounts of Al2O3 have higher selectivity for light hydrocarbons and lower selectivity for heavy hydrocarbons.     

Effect of reaction conditions and kinetic study on the Fischer-Tropsch synthesis over fused Co-Ni /Al_2O_3 catalyst

Co-Ni/Al2O3catalyst was prepared by the fusion method and used in Fischer-Tropsch synthesis(FTS).The catalysts were characterized by means of nitrogen sorption and scanning electron microscopy.The effect of some reaction conditions such as temperature,pressure and H2/CO feed ratio on the catalytic performance of Co-Ni/Al2O3in CO hydrogenation was investigated in a fixed-bed reactor.The results indicate that the optimum reaction conditions are 250℃,0.3 MPa,H2/CO feed ratio of 2.0,and GHSV of 3 000 h-1.Kinetically,the reaction rate was correlated with the Langmuir-Hinshelwood-Hougen-Watson type models.The activation energy for the best fitted model is 88.41 kJ/mol,suggesting that the intra-particle mass transport is not significant.     

Higher alcohol synthesis over Cu-Fe composite oxides with high selectivity to C2+OH

Cu-Fe composite oxides were prepared by co-precipitation method and tested for higher alcohol synthesis from syngas. The selectivity to C2+OH and C6+OH in alcohol distribution was very high while the methane product fraction in hydrocarbon distribution was rather low, demonstrating a promising potential in higher alcohols synthesis from syngas. The distribution of alcohols and hydrocarbons approximately obeyed Anderson-Schulz-Flory distribution with similar chain growth probability, indicating alcohols and hydrocarbons derived from the same intermediates. The effects of Cu/Fe molar ratio, reaction temperature and gas hourly space velocity (GHSV) on catalytic performance were studied in detail. The sample with a Cu/Fe molar ratio of 10/1 exhibited the best catalytic performance. Higher reaction temperature accelerated water-gas-shift reaction and led to lower total alcohols selectivity. GHSV showed great effect on catalytic performance and higher GHSV increased the total alcohol selectivity, indicating there existed visible dehydration reaction of alcohol into hydrocarbon.     

Dealuminated ZSM-5 Zeolite Catalyst for Ethylene Oligomerization to Liquid Fuels

Ethylene oligomerization using ZSM-5 zeolite was investigated to study the role of Bronsted acid sites in the formation of higher hydrocarbons. The oligomerization of olefins, dependent on the acidity of ZSM-5 zeolite, is an important step in the conversion of natural gas to liquid fuels. The framework Si/Al ratio reflects the number of potential acid sites and the acid strength of the ZSM-5 catalyst. ZSM-5 with the mole ratio SiO2/Al2O3 equal to 30 was dealuminated for different periods of time according to the acidic ion-exchange method to produce ZSM-5 with various Si/Al ratios. The FT-IR analysis revealed that the integrated framework aluminum band, non-framework aluminum band, and silanol groups areas of the ZSM-5 zeolites decreased after being dealuminated. The performance of the dealuminated zeolite was tested for ethylene oligomerization. The results demonstrated that the dealumination of ZSM-5 led to higher ethylene conversion, but the gasoline selectivity was reduced compared to the performance     

STUDIES ON FISCHER TROPSCH SYNTHESIS OVER Fe-Cu-K CATALYST Ⅰ.CATALYTIC PERFORMANCE

The influence of reaction pressure, temperature, space velocity (GHSV), particle size of catalyst and H2/CO ratio of feed-gas on the steady-state product distribution, conversion of CO, H2 and syngas, olefin to paraffin ratio and CO2/ H2O ratio for FTS reaction were investigated using a coprecipitated copper- potassium promoted iron catalyst. The test was carried out in a fixed-bed reactor. Increasing the reaction temperature from 493. 2 to 5-13. 2 K shifted the hydrocarbon distribution toward the heavier hydrocarbons (C5-C23) and selectively increased CO conversion to CO2. The hydrocarbon distribution was found to be dependent on the H2/CO feed-gas ratio in the range from 1.23 to 2. 22. The CO2/H2O ratio in product decreased as the flow of feed-gas rate increased, which suggests that H2O is a primary product and its reaction with CO to form CO2 occurs via a secondary process. The CO conversion increased with the decrease of catalyst particle size from 10 to 60 mesh (2. 0- 0. 3 mm), while the CO convers     

Scale up and stability test for oxidative coupling of methane over Na2WO4-Mn/SiO2 catalyst in a 200 ml fixed-bed reactor

The study of scale up for the oxidative coupling of methane （OCM） has been carried out in a 200 ml stainless steel fixed-bed reactor over a 5wt% Na2WO4-1.9wt% Mn/SiO2 （W-Mn/SiO2） catalyst. The effects of reaction conditions were investigated in detail. The results showed that, with increasing reaction temperature, the gas-phase reaction was enhanced and a significant amount of methane was converted into COx; with the CH4/O2 molar ratio of 5, the highest C2 （ethylene and ethane） yield of 25% was achieved; the presence of steam （as diluent） had a positive effect on the C2 selectivity and yield. Under lower methane gaseous hourly space velocity （GHSV）, higher selectivity and yield of C2 were obtained as the result of the decrease of released heat energy. In 100 h reaction time, the C2 selectivity of 66%-61% and C2 yield of 24.2%-25.4% were achieved by a single pass without any significant loss in catalytic performance.     

Effects of Temperature and Catalyst to Oil Weight Ratio on the Catalytic Conversion of Heavy Oil to Propylene Using ZSM-5 and USY Catalysts

It is useful for practical operation to study the rules of production of propylene by the catalytic conversion of heavy oil in FCC (fluid catalytic cracking). The effects of temperature and C/O ratio (catalyst to oil weight ratio) on the distribution of the product and the yield of propylene were investigated on a micro reactor unit with two model catalysts, namely ZSM-5/Al2O3 and USY/Al2O3, and Fushun vacuum gas oil (VGO) was used as the feedstock. The conversion of heavy oil over ZSM-5 catalyst can be comparable to that of USY catalyst at high temperature and high C/O ratio. The rate of conversion of heavy oil using the ZSM-5 equilibrium catalyst is lower compared with the USY equilibrium catalyst under the general FCC conditions and this can be attributed to the poor steam ability of the ZSM-5 equilibrium catalyst. The difference in pore topologies of USY and ZSM-5 is the reason why the principal products for the above two catalysts is different, namely gasoline and liquid petroleum gas (LPG), repspectively. So the LPG selectivity, especially the propylene selectivity, may decline if USY is added into the FCC catalyst for maximizing the production of propylene. Increasing the C/O ratio is the most economical method for the increase of LPG yield than the increase of the temperature of the two model catalysts, because the loss of light oil is less in the former case. There is an inverse correlation between HTC (hydrogen transfer coefficient) and the yield of propylene, and restricting the hydrogen transfer reaction is the more important measure in increasing the yield of propylene of the ZSM-5 catalyst. The ethylene yield of ZSM-5/Al2O3 is higher, but the gaseous side products with low value are not enhanced when ZSM-5 catalyst is used. Moreover, for LPG and the end products, dry gas and coke, their ranges of reaction conditions to which their yields are dependent are different, and that of end products is more severe than that of LPG. So it is clear that maximizing LPG and propylene and restricting dry gas and coke can be both achieved via increasing the severity of reaction conditions among the range of reaction conditions which LPG yield is sensitive to.     

Dealuminated ZSM—5 Zeolite Catalyst for Ethylene Oligomerization to Liquid Fuels

Ethylene oligomerization using ZSM-5 zeolite was investigated to study the role of Broensted acid sites in the formation of higher hydrocarbons,The oligomeriztion of olefins,dependent on the acidity of ZSM-5 zeolite ,is an important step in the conversion of natural gas to liquied fuels,The framework Si/Al ratio reflects the number of potential acid sites and the acid strength of the ZSM-5 catalyst,ZSM-5 with the mole ratio SiO2/Al2O3 equal to 30 was dealuminated for different periods of time according to the acidic ion-exchange method to produce ZSM-5 with various Si/Al ratios,The FT-IR analysis revealed that the integrated framework aluminum band,non-framework aluminum band,and silanol groups areas of the ZSM-5 zeolites decreased after being dealuminated,The performanc of the dealuminated zeolite was tested for ethylene oligomerization.The results demonstrated that the dealumination of ZSM-5 led to higher ethylene conversion,but the gasoline selectivity was reduced compared to the performance of a ZSM-5 zeolite ,The characterization results revealed the amount of aluminum in the zeolitic framework,the crystallinity of the ZSM-5 zeolite,and the Si/Al ration affected the formation of Broensted acid sites,The number of the Broensted acid sites on the catalyst active sites is important in the olefin conversion to liquied hydrocarbons.     

Partial oxidation of dimethyl ether to H2/syngas over supported Pt catalyst

Dimethyl ether （DME） is a non-toxic fuel with high H/C ratio and high volumetric energy density, and could be served as an ideal source of H2/syngas production for application in solid oxide fuel cells （SOFC）. This study presents results of DME partial oxidation over a 1.5 wt% Pt/Ce0.4Zr0.6O2 catalyst under the condition of gas hourly space velocity （GHSV） of 15000-60000 ml/（g·h）, molar ratio of O2/DME of 0.5 and 500-700 ℃, and this temperature range was also the operation temperature range for intermediate temperature SOFC. The results indicated that the catalyst showed good activity for the selective partial oxidation of DME to H2/syngas. Under the working conditions investigated, DME was completely converted. Increase in reaction temperature enhanced the amount of syngas, but lowered the H2/CO ratio and yield of methane; while increase in reaction GHSV resulted in only slight variation in the distribution of products. The good catalytic activity of Pt supported on Ce0.4Zr0.6O2 for the partial oxidation of DME may be directly associated with the good oxygen storage capacity of the support, which is worth of further investigation to develop materials for application in SOFC.