Unique Ordered TiO2 Superstructures with Tunable Morphology and Crystalline Phase for Improved Lithium Storage Properties

Unique ordered TiO₂ superstructures with tunable morphology and crystalline phase were successfully prepared by the use of different counterions. Dumbbell‐shaped rutile TiO₂ and nanorod‐like rutile mesocrystals constructed from ultrathin nanowires, and quasi‐octahedral anatase TiO₂ mesocrystals built from tiny nanoparticle subunits were achieved. Interestingly, the obtained anatase mesocrystals have a fine microporous structure and a large surface area. The influence of the counterions in the reaction system is discussed and possible mechanisms responsible for the formation of the unique ordered TiO₂ superstructures with different morphologies and crystalline phases are also proposed based on a series of experimental results. The obtained TiO₂ superstructures were used as anode materials in lithium ion batteries, and exhibited higher capacity and improved rate performance; this is attributed to the intrinsic characteristics of the mesoscopic TiO₂ superstructures, which have a single‐crystal‐like and porous nature.     

硼铈共掺杂纳米TiO2光催化降解三氯杀螨醇和菊酯类农药

采用溶胶-凝胶法在钛酸丁酯水解过程引入硼酸、硝酸铈,制备具有光催化活性的硼铈共掺杂纳米二氧化钛（TiO2）,经XRD、TEM、FT-IR、UV-Vis-DRS表征晶体结构,在日光灯照射下,光催化降解三氯杀螨醇、高氟氯氰菊酯、氟戊菊酯农药。结果表明：硼铈共掺杂的TiO2只有锐钛矿型,而纯的或掺铈的TiO2有含有锐钛矿型、金红石相和少量板钛矿型,UV-Vis-DRS测定结果表明硼铈共掺杂的TiO2禁带宽度变小,硼铈共掺杂的TiO2在可见光区吸光度高于掺杂铈和不掺杂的TiO2,在420nm~850nm有强的吸收;在同样光照下对三氯杀螨醇、高氟氯氰菊酯、氟戊菊酯的降解试验证明硼铈共掺杂纳米TiO2的光催化活性高于不掺杂或只掺杂铈的TiO2。     

Fluorine‐Doped Porous Single‐Crystal Rutile TiO2 Nanorods for Enhancing Photoelectrochemical Water Splitting

Fluorine‐doped hierarchical porous single‐crystal rutile TiO₂ nanorods have been synthesized through a silica template method, in which F^? ions acts as both n‐type dopants and capping agents to make the isotropic growth of the nanorods. The combination of high crystallinity, abundant surface reactive sites, large porosity, and improved electronic conductivity leads to an excellent photoelectrochemical activity. The photoanode made of F‐doped porous single crystals displays a remarkably enhanced solar‐to‐hydrogen conversion efficiency (≈0.35 % at ?0.33 V vs. Ag/AgCl) under 100 mW cm^?2 of AM=1.5 solar simulator illumination that is ten times of the pristine solid TiO₂ single crystals.     

Direct synthesis of Nd3+ doped mesoporous TiO2 and investigation of its photocatalytic performance

Nd³⁺ doped mesoporous TiO₂ samples with different molar ratio of Nd/Ti were synthesized by a sol?Cgel method. The textural and optical properties of the samples were systematical characterized by X-ray diffraction, transmission electron microscopy, N₂ adsorption?Cdesorption isotherms, Fourier transform infrared spectroscopy and UV?CVisible absorbance spectroscopy. It was revealed that Nd³⁺ doping inhibited the phase transformation from anatase to rutile after calcination, and the mesoporous structure of doped samples was still retained with the increase of Nd/Ti molar ratio. The surface area of the samples varied from 137 to 210 m²g^?1 and the average pore size of them ranged between 5.7 and 8.2?nm. The photocatalytic activities of all the samples were evaluated by degradation methyl orange (MO) in aqueous solution as a model reaction under UV light irradiation. The results showed that the doped samples demonstrated a higher photocatalytic activity than the mesoporous TiO₂, and the 3?mol% Nd³⁺ doped mesoporous TiO₂ exhibited the best photocatalytic performance. Meanwhile, a promotion effect of the H₂O₂ added was verified in the degradation of MO.     

Synthesis of Cristobalite Containing Ordered Interstitial Mesopores using Crystallization of Silica Colloidal Crystals

Cristobalite with ordered interstitial dual-sized mesopores was synthesized through the crystallization of silica colloidal crystals composed of monodispersed amorphous silica nanoparticles. An aqueous solution containing both a flux (Na₂O) and a carbon precursor (an aqueous low-molecular weight phenolic resin) was infiltrated into the interstices of silica colloidal crystals. The organic fraction in the nanocomposite was further polymerized and subsequently carbonized in an Ar flow at 750 °C to reinforce the colloidal crystal structure. The thermal treatment resulted in the crystallization of the colloidal crystals into cristobalite while retaining the porous structure. The cristobalite-carbon nanocomposite was calcined in air to remove the carbon and create interstitial ordered mesopores in the cristobalite. The surfaces of crystalline mesoporous silica are quite different from those of various ordered mesoporous silica with amorphous frameworks; thus, the present findings will be useful for a precise understanding and control of the interfaces between the mesopores and silica networks.     

Dispersion of TiO2 on high‐surface‐area mesoporous silica: functionalization with tungstophosphoric acid and application in solvent‐free,aerobic oxidation of n‐hexadecane

Imidazole type ionic liquid, 1‐hexadecyl‐3‐methylimidazolium chloride, was used to template the synthesis of high‐surface‐area mesoporous silica under acidic conditions and crystalline titanium dioxide (TiO₂) nanoparticles of anatase phase were inserted utilizing a solvent evaporation‐induced method. The surface area of more than 700 m² g^?1 was obtained after TiO₂ impregnation. Further, the polyoxometalate, 12‐tungstophosphoric acid (PW₁₂) was dispersed on the surface of TiO₂ to form PW₁₂–TiO₂–silica hybrid catalytic materials. The catalytic activity of this hybrid material was tested for solvent‐free, aerobic oxidation of n‐hexadecane. The experimental investigation shows that PW₁₂–TiO₂ nanocrystals did not block the pore channels and gave good conversion. Copyright © 2012 John Wiley & Sons, Ltd.     

A Blinking Mesoporous TiO2−x Composed of Nanosized Anatase with Unusually Long‐Lived Trapped Charge Carriers

A mesoporous TiO_2?x material comprised of small, crystalline, vacancy‐rich anatase nanoparticles (NPs) shows unique optical, thermal, and electronic properties. It is synthesized using polymer‐derived mesoporous carbon (PDMC) as a template. The PDMC pores serve as physical barriers during the condensation and pyrolysis of a titania precursor, preventing the titania NPs from growing beyond 10 nm in size. Unlike most titania nanomaterials, during pyrolysis the NPs undergo no transition from the anatase to rutile phase and they become catalytically active reduced TiO_2?x. When exposed to a slow electron beam, the NPs exhibit a charge/discharge behavior, lighting up and fading away for an average period of 15 s for an extended period of time. The NPs also show a 50 nm red‐shift in their UV/Vis absorption and long‐lived charge carriers (electrons and holes) at room temperature in the dark, even long after UV irradiation. The NPs as photocatalysts show a good activity for CO₂ reduction.     

The Influence of Defects on Mo‐Doped TiO2 by First‐Principles Studies

TiO₂ doped with transition metals shows improved photocatalytic efficiency. Herein the electronic and optical properties of Mo‐doped TiO₂ with defects are investigated by DFT calculations. For both rutile and anatase phases of TiO₂, the bandgap decreases continuously with increasing Mo doping level. The 4d electrons of Mo introduce localized states into the forbidden band of TiO₂, and this shifts the absorption edge into the visible‐light region and enhances the photocatalytic activity. Since defects are universally distributed in TiO₂ or doped TiO₂, the effect of oxygen deficiency due to oxygen vacancies or interstitial Mo atoms is systemically studied. Oxygen vacancies associated with the Mo dopant atoms or interstitial Mo will reduce the spin polarization and magnetic moment of Mo‐doped TiO₂. Moreover, oxygen deficiency has a negative impact on the improved photocatalytic activity of Mo‐doped TiO₂. The current results indicate that substitutional Mo, interstitial Mo, and oxygen vacancy have different impacts on the electronic/optical properties of TiO₂ and are suited to different applications.     

Novel synthesis of high-surface-area ordered mesoporous TiO2 with anatase framework for photocatalytic applications

Ordered mesoporous TiO₂ materials with an anatase frameworks have been synthesized by using a cationic surfactant cetyltrimethylammonium bromide (C₁₆TMABr) as a structure-directing agent and soluble peroxytitanates as Ti precursor through a self-assembly between the positive charged surfactant S⁺ and the negatively charged inorganic framework I^? (S⁺I^? type). The low-angle X-ray diffraction (XRD) pattern of the as-prepared mesoporous TiO₂ materials indicates a hexagonal mesostructure. XRD and transmission electron microscopy results and nitrogen adsorption–desorption isotherms measurements indicate that the calcined mesoporous TiO₂ possesses an anatase crystalline framework having a maximum pore size of 6.9 nm and a maximum Brunauer–Emmett–Teller specific surface area of 284 m² g^?1. This ordered mesoporous anatase TiO₂ also demonstrates a high photocatalytic activity for degradation of methylene blue under ultraviolet irradiation.     

Ordered Mesoporous Thin Films of Rutile TiO2 Nanocrystals Mixed with Amorphous Ta2O5

Ordered mesoporous thin films of composites of rutile TiO₂ nanocrystals with amorphous Ta₂O₅ are fabricated by evaporation‐induced self‐assembly followed by subsequent heat treatment beyond 780 °C. Incorporation of selected amounts of Ta₂O₅ (20 mol %) in the mesoporous TiO₂ film, together with the unique mesoporous structure itself, increased the onset of crystallization temperature which is high enough to ensure the crystallization of amorphous titania to rutile. The ordered mesoporous structure benefits from a block‐copolymer template, which stabilizes the mesostructure of the amorphous mixed oxides before crystallization. The surface and in‐depth composition analysis by X‐ray photoelectron spectroscopy suggests a homogeneous intermixing of the two oxides in the thin film. A detailed X‐ray absorption fine structure measurement on the composite film containing 20 mol % Ta₂O₅ and heated to 800 °C confirms the amorphous nature of the Ta₂O₅ phase. Photocatalytic activity evaluation suggests that the rutile nanocrystals in the synthesized ordered mesoporous thin film possess good ability to assist the photodegradation of rhodamine B in water under illumination by UV light.     

Electrochemical Fabrication and Properties of Highly Ordered Fe‐Doped TiO2 Nanotubes

Highly‐ordered Fe‐doped TiO₂ nanotubes (TiO₂nts) were fabricated by anodization of co‐sputtered Ti–Fe thin films in a glycerol electrolyte containing NH₄F. The as‐sputtered Ti–Fe thin films correspond to a solid solution of Ti and Fe according to X‐ray diffraction. The Fe‐doped TiO₂nts were studied in terms of composition, morphology and structure. The characterization included scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, X‐ray diffraction, UV/Vis spectroscopy, X‐ray photoelectron spectroscopy and Mott–Schottky analysis. As a result of the Fe doping, an indirect bandgap of 3.0 eV was estimated using Tauc’s plot, and this substantial red‐shift extends its photoresponse to visible light. From the Mott–Schottky analysis, the flat‐band potential (E_fb) and the charge carrier concentration (N_D) were determined to be ?0.95 V vs Ag/AgCl and 5.0 ×10¹⁹ cm^?3 respectively for the Fe‐doped TiO₂nts, whilst for the undoped TiO₂nts, E_fb of ?0.85 V vs Ag/AgCl and N_D of 6.5×10¹⁹ cm^?3 were obtained.     

Synthesis and Modification of Zn‐doped TiO2 Nanoparticles for the Photocatalytic Degradation of Tetracycline

The synthesis of Zn‐doped TiO₂ nanoparticles by solgel method was investigated in this study, as well as its modification by H₂O₂. The catalyst was characterized by transmission electron microscopy, X‐ray diffraction, Brunauer–Emmett–Teller, UV–visible reflectance spectra and X‐ray photoelectron spectroscopy (XPS). The results indicated that doping Zn into TiO₂ nanoparticles could inhibit the transformation from anatase phase to rutile phase. Zn existed as the second valence oxidation state in the Zn‐doped TiO₂. Zn‐doped TiO₂ that was synthesized by 5% Zn doping at 450°C exhibited the best photocatalytic activity. Then, the H₂O₂ modification further enhanced the photocatalytic activity. Zn doping and H₂O₂ modifying narrowed the band gap and efficiently increased the optical absorption in visible region. The optimal degradation rate of tetracycline by Zn‐doped TiO₂ and H₂O₂ modified Zn‐doped TiO₂ was 85.27% and 88.14%. Peroxide groups were detected in XPS analysis of H₂O₂ modified Zn‐doped TiO₂, favoring the adsorption of visible light. Furthermore, Zn‐doped TiO₂ modified by H₂O₂ had relatively good reusability, exhibiting a potential practical application for tetracycline's photocatalytic degradation.     

Photocatalytic Activity for Water Decomposition to Hydrogen over Nitrogen‐doped TiO2 Nanoparticle

Nitrogen-doped TiO2 nanoparticle photocatalysts were obtained by an annealing method with gaseous ammonia and nitrogen. The influence of dopant N on the crystal structure was characterized by XRD, XPS, BET, TEM and UV-Vis spectra. The results of XRD indicate that, the crystal phase transforms from anatase to rutile structure gradually with increase of annealing temperature from 300 to 700 ℃. XPS studies indicate that the nitrogen atom enters the TiO2 lattice and occupies the position of oxygen atom. Agglomeration of particles is found in TEM images after annealing. BET results show that the specific surface areas of N-doped samples from 44.61 to 38.27 m2/g are smaller than that of Degussa TiO2. UV-Vis spectra indicate that the absorption threshold shifts gradually with increase of annealing temperature, which shows absorption in the visible region. The influence of annealing condition on the photocatalytic property has been researched over water decomposition to hydrogen, indicating that nitrogen raises the photocatalytic activity for hydrogen evolution, and the modified TiO2 annealed for 2 h at 400 ℃ under gas of NH3/N2 (V/V＝1/2) mixture shows better efficiency of hydrogen evolution. Furthermore, the N-doped TiO2 nanoparticle catalysts have obvious visible light activity, evidenced by hydrogen evolution under visible light (λ＞400 nm) irradiation. However, the catalytic activity under visible light irradiation is absent for Degussa as reference and the N-doped TiO2 annealed at 700 ℃.     

Synthesis of Three‐dimensionally Ordered Macroporous TiO2 and TiO2/WO3 Composites and Their Photocatalytic Performance

This work presents the characterization and preparation of three‐dimensionally ordered macroporous TiO₂ and TiO₂/WO₃ composite nanoparticles with enhanced visible‐light‐responsive properties for rhodamine B (Rh B) photodegradation. The 3DOM TiO₂ and TiO₂/WO₃ composites were prepared through a dip‐infiltrating sol‐gel process using a polystyrene (PS) colloidal crystal template. The materials were characterized by SEM, TEM, XRD, BET, XPS and UV/Vis. The 3DOM TiO₂/WO₃ composite structures ranged from well‐defined 3DOM structures, which are highly ordered and interconnected via small pore windows, to collapsed three‐dimensional structures as the WO₃ content increased. The photoresponse range and specific surface area of the composite increased with less than 0.025 g of WCl₆. The 3DOM TiO₂/WO₃ composite with less than 0.025 g of WCl₆ exhibited a higher catalytic activity than 3DOM TiO₂ for the photocatalytic degradation of Rh B under simulated sunlight illumination.     

Synthesis and Studies of the Visible‐Light Photocatalytic Properties of Near‐Monodisperse Bi‐Doped TiO2 Nanospheres

Near‐monodisperse Bi‐doped anatase TiO₂ nanospheres with almost uniform diameters in the range of 117 to 87 nm were prepared simply by introducing different amounts of bismuth nitrate pentahydrate into the reaction system and subsequent calcinations. X‐ray diffraction, UV‐visible diffuse reflectance spectra, and X‐ray photoelectron spectroscopy confirm that the doped ions substitute some of the lattice titanium atoms, and furthermore, Bi³⁺ and Bi⁴⁺ ions coexist. All the Bi‐doped TiO₂ samples show much better photocatalytic activity than pure TiO₂ in the degradation of rhodamine B (RhB) under the irradiation of visible light (λ>420 nm), and, interestingly, it was found that the degradation mechanism is different from the conventional one, which has already been reported elsewhere. The detailed mechanism is discussed in this article.     

Reduced Graphene Oxide‐Supported TiO2 Fiber Bundles with Mesostructures as Anode Materials for Lithium‐Ion Batteries

Although the synthesis of mesoporous materials is well established, the preparation of TiO₂ fiber bundles with mesostructures, highly crystalline walls, and good thermal stability on the RGO nanosheets remains a challenge. Herein, a low‐cost and environmentally friendly hydrothermal route for the synthesis of RGO nanosheet‐supported anatase TiO₂ fiber bundles with dense mesostructures is used. These mesostructured TiO₂‐RGO materials are used for investigation of Li‐ion insertion properties, which show a reversible capacity of 235 mA h g^?1 at 200 mA g^?1 and 150 mA h g^?1 at 1000 mA g^?1 after 1000 cycles. The higher specific surface area of the new mesostructures and high conductive substrate (RGO nanosheets) result in excellent lithium storage performance, high‐rate performance, and strong cycling stability of the TiO₂‐RGO composites.     

Thermal and hydrothermal stability of flame hydrolytically synthesized SiO2/TiO2 mixed oxides

The phase stability of the two TiO₂ modifications (anatase and rutile) in fumed SiO₂/TiO₂ nano-composites (0–24.8 wt-% silica) under thermal and hydrothermal conditions was investigated by X-ray powder diffraction, transmission electron microscopy (TEM) and gas adsorption methods (BET). The results show that the phase transformation from anatase to rutile type of structure and the growth of anatase crystallites are significantly retarded by mixing small amounts of SiO₂ into TiO₂, while the specific surface area is maintained. The SiO₂/TiO₂-composites reveal a remarkable shift in the anatase to rutile transformation temperature from approx. 500 °C (pure TiO₂) to approx. 1000 °C (samples with SiO₂ contents of more than 10%). The rate of phase transformation from anatase to rutile is enhanced under hydrothermal conditions compared to conventional thermal treatment, e.g. pure titania (AEROXIDE^® TiO₂ P25) annealed under hydrothermal conditions (100 g/m³ absolute humidity, 4 h at 600 °C) had a rutile content of 85%, while the same specimens annealed in absence of humidity contained only 46% rutile. However, the difference in rate of phase transformation became less pronounced when the silica content in SiO₂/TiO₂-composites was further increased.TEM results showed that the surface of the anatase crystallites was covered with silica. This averts coalescence of anatase crystallites and keeps them under a critical size during the annealing process. When the crystal domains grew larger, a rapid conversion to rutile took place. The critical size of anatase crystallites for the phase transformation was estimated to be 15–20 nm.     

Preparation of Cr‐doped TiO2/SiO2 Photocatalysts and their Photocatalytic Properties

Cr‐doped TiO₂/SiO₂ nanostructured materials were prepared employing a layer‐by‐layer assemblym technique. TiO₂ colloids were synthesized by a sol‐gel method using TiCl₄ as a precursor. The experimental results showed that sphere‐type TiO₂ particles on SiO₂ exhibited uniform shape and a narrow size distribution. The amount of Ti (wt %) increased as a function of the number of the coating layers. The coatingv layers was composed of anatase titania nanocrystals at 550 °C. The onset of band‐gap transition for Crdoped TiO₂/SiO₂ showed a red shift compared with that for the undoped TiO₂/SiO₂. And the photocatalytic activity of Cr‐doped TiO₂/SiO₂ was higher than that of undoped sample.     

The effects of trace elements on the crystal properties of TiO2

The effects of trace element doping of TiO₂ on the crystal growth and on the anatase-to-rutile phase transformation of TiO₂ were investigated. The co-precipitation process, from sulfate solution, of doped (Cr, Fe, V, Nb, Si, P) TiO₂ was also studied. The heating temperatures were 473, 673, 873, 993, 1133 K and a higher temperature needed to achieve a rutile content of 98–99%. Traces of reduced titanium were found in freshly calcined anatase by X-ray diffraction. Pure anatase structure was found in 85% of the samples heated below 1000 K. Anatase-to-rutile transformation was accelerated by the mmol% content of Nb, Cr, Si, and Fe in TiO₂. Interaction of co-precipitated or impregnated cations was found critical in the phase transformation process. Nb retarded the crystal growth during calcination. Sulfate ions minimized the specific surface area of TiO₂ heated at low temperatures. These results of doped TiO₂ serve to promote the development of new high-technology TiO₂ products for photocatalytic purposes.     

Synthesis of Fe<Superscript>3+</Superscript> doped ordered mesoporous TiO<Subscript>2</Subscript> with enhanced visible light photocatalytic activity and highly crystallized anatase wall

Fe³⁺ doped mesoporous TiO₂ with ordered mesoporous structure were successfully prepared by the solvent evaporation-induced self-assembly process using P123 as soft template. The properties and structure of Fe³⁺ doped mesoporous TiO₂ were characterized by means of XRD, EPR, BET, TEM, and UV–vis absorption spectra. The characteristic results clearly show that the amount of Fe³⁺ dopant affects the mesoporous structure as well as the visible light absorption of the catalysts. The photocatalytic activity of the prepared mesoporous TiO₂ was evaluated from an analysis of the photodegradation of methyl orange under visible light irradiation. The results indicate that the sample of 0.50%Fe–MTiO₂ exhibits the highest visible light photocatalytic activity compared with other catalysts.