水煤浆添加剂与煤之间的相互作用规律研究 Ⅰ. 复合煤颗粒间的相互作用对水煤浆流变性的影响

使用12种不同分散剂对14种不同变质程度的煤进行了成浆性实验，分析了182个水煤浆(CWS)样品的流变性。结果表明，低变质程度和高灰煤浆多呈屈服假塑性，煤的性质起主导作用；变质程度高且灰分较低煤浆的流变性，主要依赖于分散剂的结构与性质；分子结构单元立体空间效应大，疏水基团与亲水基团呈立体间隔分布的分散剂，易形成屈服假塑性CWS；分子线度长，亲水基团与疏水基团呈线性间隔分布的分散剂，易形成胀塑性CWS。复合煤粒间的相互作用方式是决定CWS流变特性的关键。     

Inverse gas chromatography in the study of polymer degradation. Part 4: A study of model systems for reinforced vulcanizates

Summary Inverse gas chromatography with olefinic stationary phases, impregnated with silica gel or carbon black, and air as carrier gas has been found to yield characteristic shifts of retention data and concomitant changes in peak shape. The plots of retention index versus oxygen flow obtained indicate carbon black to have significant antioxidant properties, which are not altogether lost on solvent extraction. On the other hand, silica gel yields results consistence with the existence of a novel chain scission repair process.     

高分子型炭黑分散剂的合成及其性能研究

研究了嵌段型分分子颜料分散剂的合成及其有炭黑分散体系中的分散稳定作用。结果表明，高分子嵌段分散剂在炭黑分散体系中能明显改善分散稳定性。同时发现，嵌段分散剂的组成、结构及分子量对分散作用有综合影响。     

Interaction of binders with dispersant stabilised alumina suspensions

The rheological response of selected aqueous alumina suspensions, stabilised with a polyelectrolyte or with an organic polyvalent salt dispersant, and including poly(vinyl) alcohol (PVA) as a binder, are described in this study. The polymer dispersant was composed of an ammonium salt of poly(methacrylate) and the organic polyvalent compound was a sodium salt of an aromatic sulphate. The results show that the addition of PVA, without any included dispersant does not significantly influence the rheology of the system. However, in the presence of a dispersant the rheology is greatly affected. At a given concentration of the dispersant, the viscosity, storage and loss moduli all increase, as the PVA concentration is increased. Also, for a given concentration of the PVA, it is observed that the viscosity, storage and loss moduli values increase as the concentration of the dispersant is increased. It is argued that at low PVA concentrations, an excess concentration of the unadsorbed dispersant causes flocculation of the particles in the suspension by a reduction of the repulsive electrostatic (double layer) effect. In contrast, at higher concentrations of the PVA the flocculation of the suspension is promoted via a depletion mechanism.     

水溶性分散剂的合成及其性能研究

合成了苯乙烯－顺丁烯二酸酐共聚型水溶性分解剂，并讨论了这种分散剂对导电粉及炭黑等难分散颜料的分散稳定性作用。结果表明，在水介质中，该发散剂能明显改善导电粉和炭黑颜料的分散稳定性。     

Rheological Characterization of Alumina Ceramic Suspensions in Presence of a Dispersant and a Binder

The rheological responses of aqueous alumina suspensions, stabilized with an organic polyvalent salt dispersant called “Aluminon,” and including a poly(vinyl) alcohol (PVA) binder, are described in this study. It is observed that the addition of PVA, without any dispersant does not significantly influence the rheology. However, in the presence of the dispersant the rheology is affected significantly. At a given concentration of the dispersant, the viscosity, the storage and loss modulii all increase with the PVA concentration. Also, for a given concentration of the PVA, the viscosity, the storage and loss modulii values increases as the concentration of the dispersant is increased. At relatively low PVA concentrations, an excess concentration of the dispersant, causes flocculation of the particles in the suspension by a reduction of the electrostatic (double layer) effect. On the contrary, at higher concentrations of the PVA the flocculation of the suspension occurs via a depletion mechanism.     

Scaling in Electrical Conductivity Measurements and Rheological Measurements of Monarch 700 Dispersions Stabilized by Polymers

For making stable dispersions of graphitic carbon black (Monarch 700), the effectiveness of three dispersants/polymers (hypermer LP1, hypermer B246, and OLOA 11000) in xylene is investigated. Hypermer LP1 (polyhydroxystearic acid) is a homopolymer and hypermer B246 (PEG 30-dipolyhydroxystearate) is a polyhydroxystearic acid/polyethylene oxide/polyhydroxystearic acid ABA block copolymer, while OLOA 11000 (polyisobutylene succinimide) has a polar head group (polyamine) attached to a hydrocarbon chain (polyisobutylene). Well-dispersed graphitic carbon black dispersions were prepared using dispersants at optimum concentrations. Percolation threshold and rheological threshold were determined by analyzing the variations in electrical conductivity and elastic modulus with concentration of carbon black. Above threshold concentration, scaling law was applied to experimental data of rheology (dynamic measurements) and electrical conductivity measurements to evaluate quality of the system. Effectiveness of polymers was investigated on the basis of value of critical exponent (t and t′, respectively) in scaling power law. Hypermer LP1 was proved to be a poor dispersant for Monarch 700 dispersions while other two polymers were found to be effective stabilizers.     

Temperature dependence of the colloidal agglomeration inhibition: computer simulation study

There exist experimental evidences that the structure and extension of colloidal aggregates in suspensions change dramatically with temperature. This results in an associated change in the suspension rheology. Experimental studies of the inhibitor applications to control the particle clustering have revealed some unexpected tendencies. Namely, the heating of colloidal suspensions has provoked either extension or reduction of the colloidal aggregates. To elucidate the origin of this behavior, we investigate the influence of temperature on the stabilizing effect of the inhibitor, applying an associative two-component fluid model. Our results of the canonical Monte Carlo simulations indicate that the anomalous effect of the temperature may not be necessarily explained by the temperature dependent changes in the inhibitor tail conformation, as has been suggested recently by Won et al. [Langmuir 21, 924 (2005)]. We show that the competition between colloid-colloid and colloid-inhibitor associations, which, in turn, depends on the temperature and the relative concentrations, may be one of the main reasons for the unexpected temperature dependence of inhibitor efficacy.     

Mechanical and rheological properties of poly(ethylene-co-ethyl acrylate) as a function of carbon black content

Carbon black (CB) filled poly(ethylene-co-ethyl acrylate) (EEA-CB) is used as conductive phase in conductive polymer composites (CPC). Electrical conductivity of CPC obtained from blends of immiscible polymers results from CB particles localization within the material, which depends on composition and processing conditions. It is particularly important to control viscosity of such systems as this parameter determines both the phase morphology and conductive pathway structure. The small scale, at which CB particle aggregation/dispersion phenomena occur within CPC, makes direct observations difficult. But the effect of carbon black particles/polymers interactions is clearly visible by means of rheological measurements. A strong reinforcing effect of CB on CPC in both solid and liquid states has been noticed. This phenomenon has been analyzed using classical models as a function of temperature and CB content. The results confirm the necessity of CPC rheology control especially during the process to achieve good reproducibility of electrical properties.     

阴离子分散剂对酸化膨润土流变性的影响

研究了阴离子分散剂聚丙烯酸钠对质量分数为10%的酸化膨润土分散体系流变性的影响. 结果表明, 添加0.4%分散剂的分散体系的剪切应力、表观黏度和屈服应力最低. 其它体系流体均表现为从假塑型到胀流型流体的转变, 而含0.4%分散剂的体系始终表现为胀流型流体. 采用Herschel-Bulkley模型对各体系的流变曲线进行了拟合, 得到较好的拟合曲线, 同时探讨了酸化膨润土分散体系的流变机理.     

炭黑填充聚苯乙烯熔体流变行为

研究了炭黑(CB)填充聚苯乙烯(PS)熔体的稳态和动态流变行为. CB/PS复合体系在CB体积分数φ=0.06时发生逾渗转变. 结果表明, 低应变区熔体模量降低主要归因于粒子-粒子及粒子-高分子间作用力的破坏, 高应变下模量的急剧下降则主要与高分子链间解缠结有关. 采用“两相”模型拟合线性动态流变行为, 发现应变放大因子A_f(φ)、填充相模量及松弛指数与温度有关. A_f(φ)~φ关系符合Guth方程和扩散控制的粒子簇聚集模型. “粒子相”形状参数与聚集体分维度均随温度升高而有所降低, 说明CB粒子聚集体因团聚而趋于各向同性, 应变放大效应减弱. “粒子相”特征模量G'_f1(φ)和G"_f0(φ)与φ关系满足标度律. 当φ > 0.06时, G'_f1(φ)和G"_f0(φ)及其标度指数均随温度升高而明显降低, 其G'_f1(φ)变化幅度略大于G"_f0(φ), 说明“粒子相”弹性与黏性组分具有不同的温度依赖性. 随着温度升高, 扩散控制的CB粒子团聚过程加快, 应变放大效应减弱.     

Thermal characterization of biomass smoke particles

In this paper we present results on characterization of filter-collected redwood (Sequoia sempevirens)-needle and eucalyptus smoke particles by thermal, optical, and solvent extraction methods. Our results show that black carbon and a significant fraction of organic carbon in biomass smoke particles have similar volatility and combustion temperatures. Combustion temperatures of both black carbon and this organic fraction critically depend on the concentrations of common constituents of biomass smoke such as Na and K. These species are also known to catalyze the combustion and therefore lower the combustion temperatures by more than 100 °C. Consequently, thermal methods that rely on a specific temperature to separate organic from black carbon may either underestimate or overestimate the black and organic carbon concentrations, depending on the amounts of Na and K and on the composition and concentration of organic material present in a sample. These results suggest that more than one method must be used to accurately determine the organic and black carbon concentrations in biomass smoke particles.     

Charge transport in melt-dispersed carbon nanotubes

We investigate the effect of interfacial stabilizer on charge transport in polymer-dispersed carbon nanotubes. Despite mechanical contact, samples with dispersant show poor conductivity, which we attribute to a robust interfacial layer between contacted nanotubes. In comparison, results obtained when nanotubes are mechanically mixed into polymer melts without dispersant show much better conductivity. The difference is striking; at comparable loading, neat melt composites have resistivities five orders of magnitude smaller than those containing interfacial stabilizer. Our results highlight a fundamental issue for the engineering of conducting carbon nanotube composites; dispersion stability will typically be achieved at the expense of conductivity.     

Effect of surface structure on the charge storage capacity of carbon black electrodes

In this work we study the effect of surface structure on the charge storage capacity of carbon black electrodes with various changes in surface chemistry, morphology, and doping species. Cyclic voltammetry and chronopotentiometry studies, performed under alkaline conditions with carbon paste electrodes, indicate the importance of surface structure and grain size on the faradic and capacitive charge contributions of these materials. Among the various carbon blacks studied, the lithiated material shows superior charge storage capacity, suggesting the importance of alkaline metals and oxygenated groups on the carbon surface. For the graphitic carbon, the appearance of a reversible redox process with cycling resembles the electrochemical behavior reported for hydrogen storage in carbon nanotubes. Electronic Publication     

乙烯类聚合物-炭黑复合物的PTC效应

本文以低密度聚乙烯(LDPE)和乙烯-醋酸乙烯酯共聚物(EVA)为基材,炭黑(CB)为导电微粒,探讨了聚合物-炭黑复合物的结构对正温度系数效应(PTC)增强与减弱的影响和炭黑含量与PTC效应的关系以及交联结构对PTC现象的稳定作用.     

Rheology of a reversible supramolecular polymer studied by comparison of the effects of temperature and chain stoppers

The rheology of a reversible supramolecular polymer is studied by comparing the effects of an increase in temperature and the addition of chain stoppers. The dependence of the zero-shear viscosity and the terminal relaxation time on temperature is exponential, and the activation energy for viscous flow can be calculated. Above a critical stopper fraction, power laws describe the stopper dependence of the viscosity and relaxation time. A simple model for the effect of the addition of chain stoppers on the average degree of polymerization adequately describes the results. A comparison of flow curves at several temperatures and stopper fractions reveals considerable differences between solutions with the same zero-shear viscosity. These are mainly associated with differences in the terminal relaxation time. A mechanism of shear-induced alignment and subsequent elongation of chains is proposed, with which the experimental results are consistent.     

不同粒径炭黑混合对复合型导电材料PTC性能的影响

研究了炭黑分散效果对具有PTC效应的高密度聚乙烯／炭黑导电复合材料性能的影响。实验结果表明，由不同粒度和比表面积的两种炭黑混合后填充的复合材料同由导电性能较好的乙炔炭黑填充复合材料比较，前者具有较低的渗滤阀值、较高的临界温度、优良的PTC特性以及电阻稳定性好的特点．     

Experimental clues of soft glassy rheology in strained filled elastomers

Tensile stress‐relaxation measurements have been performed on a series of cross‐linked filled elastomers. The fillers are chosen to investigate the effect of the filler–filler and the filler–matrix interactions on the time dependence of the tensile relaxation modulus E(t) after UP and DOWN jumps. For the carbon black‐filled sample (strong filler–elastomer interaction) E(t) decreases as log(t) when the strain ε is strictly larger than 0.2 and reached by UP jumps. For the silica‐filled samples in the same conditions, and for all samples after a DOWN jump, including ε = 0.2, the experimental data can be fitted with a power law equation characterized by the exponent m. Thus, in all cases, |dE(t)/dt| scales as t^?α with α ? m + 1. Pertinence of the soft glassy rheology model for interpreting these results is examined. It is shown that α could be equivalent to the effective noise temperature x and related to the polymer chain mobility. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 647–656     

甲烷在石墨化热解碳黑和活性炭上的吸附

为研究影响碳基吸附剂吸附超临界温度气体的主要因素,选择石墨化热解碳黑BP280和Ajax活性炭,分析超临界温度高压甲烷在其上的吸附平衡。应用容积法,在压力0~20.5 MPa、温度253 K~313 K测定甲烷的吸附平衡数据,并由等量吸附线标绘和亨利定律常数确定等量吸附热。引入通用吸附等温方程,再由方程的Langmuir标绘确定最大吸附容量,进而通过方程的线性化计算吸附平衡态中甲烷分子的作用能。结果表明,甲烷在两种吸附剂上的最大吸附容量均随温度而变化,并都小于液态甲烷的密度;甲烷在碳黑和活性炭上的等量吸附热分别为11.9 kJ/mol~12.5 kJ/mol和17.5 kJ/mol~22.5 kJ/mol,体现了两种吸附剂不同的表面能量分布;甲烷分子间作用能随吸附量的变化特点反映了超临界温度甲烷以类似于压缩气体状态聚集的特点和吸附剂结构上的差异。碳基吸附剂的比表面积和微孔容积是影响其储存甲烷容量的重要因素。