连续样条小波变换用于分解重叠峰的研究

以B-样条小波为分析小波，提出了用于分析化学重叠信号解析的新方法——连续样条小波变换，结果表明：连续样条小波变换应用于分析化学信号的处理，能使峰变窄同时还能提高信号的信噪比，是一种新型有效的重叠信号解析方法，能从含噪声重叠信号中直接得到重叠峰的峰数目及其相应的峰位置。     

自适应中值滤波用于色谱信号去噪的研究

在分析化学领域中，如何从被干扰的信号中有效去除噪声并恢复有用信号，具有重要的意义。此文从中值滤波基本概念出发，针对经典中值滤波器滑动窗口长度固定对信号去噪的影响，提出了自适应中值滤波器，通过对某元素色谱曲线进行去噪处理，并与移动均值法和小波变换法进行比较表明，此方法不仅能有效地滤除脉冲和高斯噪声，而且使色谱峰的边缘得到良好保护，从而提高了色谱数据分析的精确性。     

芳香烃异构体的毛细管柱气相色谱—傅里叶变换红外光谱联用技术分析

采用国产色谱仪与进口红外光谱仪及接口组成的气相色谱－傅里叶变换红外光谱（ＧＣ／ＦＴＩＲ）分析仪，使用大口径毛细管柱，分析了乙苯与苯乙烯固相催化反应液的复杂芳香烃异构体组成，讨论了ＧＣ／ＦＴＩＲ分析中随机噪声和基线漂的去除方法。采用等高线图９ＣＴＤ）分析技术得混合液中各组分的纯气相红外光谱图，最后了１４个气相色谱峰中的９个，占整个色谱峰面积９９５以上。     

芳香烃异构体的毛细管柱气相色谱－傅里叶变换红外光谱联用技术分析

采用国产色谱仪与进口红外光谱仪及接口组成的气相色谱－傅里叶变换红外光谱（ＧＣ／ＦＴＩＲ）分析仪，使用大口径毛细管柱，分析了乙苯与苯乙烯固相催化反应液的复杂芳香烃异构体组成，讨论了ＧＣ／ＦＴＩＲ分析中随机噪声和基线漂移的去除方法。采用等高线图（ＣＴＤ）分析技术得到了混合液中各组分的纯气相红外光谱图，最后鉴定了１４个气相色谱峰中的９个，占整个色谱峰面积９９％以上。     

裂解毛细管柱气相色谱－傅里叶变换红外光谱的剖析应用

采用裂解气相色谱－傅里叶变换红外光谱（ＰｙＧＣ／ＦＴＩＲ）技术，使用大口径毛细管柱，分析了一未知进口涂料，对其主要裂解碎片峰进行了定性，进而从特征碎片的产生推出该涂料的成分。并同常规红外光谱差减法进行了比较，结果表明ＰｙＧＣ／ＦＴＩＲ具有简便、快速、全面和无需标样等优点，有广泛的应用价值。     

裂解毛细管柱气相色谱－傅里叶变换红外光谱的剖析应用

 采用裂解气相色谱－傅里叶变换红外光谱（ＰｙＧＣ／ＦＴＩＲ）技术，使用大口径毛细管柱，分析了一未知进口涂料，对其主要裂解碎片峰进行了定性，进而从特征碎片的产生推出该涂料的成分。并同常规红外光谱差减法进行了比较，结果表明ＰｙＧＣ／ＦＴＩＲ具有简便、快速、全面和无需标样等优点，有广泛的应用价值。     

基于提升格式的小波变换用于处理化学信号

将提升haar小波变换应用于对不同类型含高噪声化学信号的处理,提出1种用于高噪声化学信号中滤除噪声的快速新方法——提升小波滤噪法,并使之与重叠峰分辨技术联用;以优选的小波分解层数对低信噪比的分析化学信号进行基于提升格式的小波变换处理,取得满意的结果;方法简单、快捷、准确、易行．运算速度是传统小波变换的一半,对高噪声化学信号的处理结果信噪比提高几百倍,峰位置相对误差小于1．5％;应用于氨基酸体系毛细管电泳检测信号的处理,有效降低了实验噪声的影响,分辨提取了难以察觉的信号．结果峰形变窄,峰高增加．大大提高了峰的分辨率．验证和显示了方法的可行性和优越性。     

(R,S)-α-羟基苯丁酸乙酯的HPLC手性分离

建立了手性柱HPLC法测定盐酸贝那普利的中间体(R)-α-羟基苯丁酸乙酯中的(S)-α-羟基苯丁酸乙酯。采用Chiralcel OD-H色谱柱,流动相正己烷-异丙醇（体积比90：10),流速1．0mL／min,检测波长254nm,进样体积20μL,按外标法以峰面积计算(R)-α-羟基苯丁酸乙酯中的(S)-α-羟基苯丁酸乙酯的含量。(S)体的线性范围5．5～23．8μg／mL,检出限0．47μg／mL(S／N=3),回收率为96％～103％,精密度RSD为2．1％(n=6)。     

快速傅立叶变换用于色谱噪声平滑及微弱信号的检测

应用快速傅立叶变换法（ＦＦＴ）对色谱噪声进行平滑处理及微弱信号检测,同时,也与其他数字滤波法进行了比较。结果表明,利用ＦＦＴ法可以很好地对噪声进行平滑处理,使信噪比提高１８倍,为更好地进行痕量组分的色谱微弱信号检测打下了基础。     

红外付里叶变换光谱及其在分析化学上的应用

(一)红外付里叶变换光谱付里叶变换(FT)是发生在自然界里最普通的变换之一。人们驾驭了这个变换的特点并已经将它用到了脑照相术、x-射线晶体学、雷达网络设计、红外光谱、核磁共振、离子回旋共振质谱、电化学、图象辨认和信息处理等领域中。时间域的强度谱与频率域的强度谱,在数学上是互为付里叶变换的。用某种实验手段首先取得时间域的强度谱,而后再以Cooley-Tukeyf快速付里叶变换算法用计算机将其计算成人们所熟悉的频率域的强度谱,已成为波谱学常用的一种技术。红外付里叶变换光谱(FT-IR)就是利用干     

Preparation and characterization of Nafion/SPEEK layered composite membrane and its application in vanadium redox flow battery

In order to reduce the cost of membrane used in vanadium redox flow battery (VRB) system while keeping its chemical stability, Nafion/sulfonated poly(ether ether ketone) (SPEEK) layered composite membrane (N/S membrane) consisting of a thin layer of recast Nafion membrane and a layer of SPEEK membrane were prepared by chemical crosslink the sulfonic acid groups of different ionomer membranes. Scanning electron microscopy (SEM) and IR spectra analysis of the membrane showed that Nafion layer was successfully deposited on the SPEEK membrane surface and an integral layered membrane structure was formed. The area resistance and permeability of vanadium ions of membrane were also measured. It was found that N/S membrane have a very low permeability of vanadium ions accompanied by a little higher area resistance compared with Nafion membrane. As a result, the VRB single cell with N/S membrane exhibited higher coulombic efficiency and lower voltage efficiency compared with VRB single cell with Nafion membrane. Although N/S membrane delivered relatively lower energy efficiency compared with Nafion membrane, its good chemical stability and low cost make it a suitable substitute for Nafion membrane used in VRB system.     

Aminoborohydrides. 12. Novel tandem S(N)Ar amination-reduction reactions of 2-halobenzonitriles with lithium N,N-dialkylaminoborohydrides

A novel tandem amination-reduction reaction has been developed in which 2-(N,N-dialkylamino)benzylamines are generated from 2-halobenzonitriles and lithium N,N-dialkylaminoborohydride (LAB) reagents. These reactions are believed to occur through a tandem S(N)Ar amination-reduction mechanism wherein the LAB reagent promotes halide displacement by the N,N-dialkylamino group, and the nitrile is subsequently reduced. This one-pot procedure is complimentary to existing synthetic methods and is an attractive synthetic tool for the nucleophilic aromatic substitution of halobenzenes with less nucleophilic amines. The (N,N-dialkylamino)benzylamine products of this reaction are easily isolated after a simple aqueous workup procedure in very good to excellent yields.     

Catalytic activation of the leaving group in the S(N)2 reaction

A novel catalytic activation of the leaving group in the S(N)2 reaction is achieved as an extension of our mercuric triflate-catalyzed reactions. Derivatives of anilinoethyl 4-pentynoate reacted smoothly with catalytic amounts of Hg(OTf)(2) to give indoline derivatives in excellent yield with efficient catalytic turnovers under very mild conditions. The reaction of optically pure secondary alcohol derivatives resulted in inversion of stereochemistry, which is a definitive feature of the S(N)2 reaction. The procedure is applicable for benzoazepine synthesis.     

Determination of perfluorooctane sulfonate in river water by liquid chromatography/atmospheric pressure photoionization mass spectrometry by automated on-line extraction using turbulent flow chromatography

A simple, fast and sensitive liquid chromatography/atmospheric pressure photoionization mass spectrometry (LC/APPI-MS) method, with automated on-line extraction using turbulent flow chromatography (TFC), was developed for the determination of perfluorooctane sulfonate (PFOS) in river water. In this method, following an on-line extraction by injection onto a column under TFC conditions, PFOS is back-flushed onto a reversed-phase column via on-line column switching, and resolved chromatographically at a laminar flow rate of 1 mL min(-1). Using this tandem LC-LC/APPI-MS system the extraction, separation and selective detection of PFOS in river water could be achieved with satisfactory selectivity and sensitivity. The limit of detection (LOD) (S/N = 3) and the limit of quantitation (LOQ) (S/N = 10)were 5.35 and 17.86 pg mL(-1). The described procedure was very simple since no off-line sample preparation was required, total analysis time being 18.75 min.     

Giant brainlike aggregates from new fluorocarbon/hydrocarbon hybrid cationic surfactants

A rapid synthetic procedure in two steps from perfluoroalkylethyl iodide derivatives led to 18 novel ammonium type hybrid surfactants of the general formula: R(F)(CH(2))(2)S(CH(2))(2)N(+)(CH(3))(2)R(H)Br(-) (R(F) = C(4)F(9), C(6)F(13), C(8)F(17); R(H) = C(4)H(9), C(6)H(13), C(8)H(17), C(10)H(21), C(12)H(25), C(14)H(29)). These hybrid surfactants exhibited very low surface tension (from 16 to 25 mN/m) as well as low critical micellar concentration until 1.5 × 10(-5) mol/L. A special focus was made on aggregation phenomenon as giant multilamellar "brainlike" vesicles were observed via cryogenic scanning electron microscopy (cryoSEM) and transmission electron microscopy (TEM; with a contrast agent) suggesting a high encapsulation ability and a very important specific surface of these particular organizations.     

Influence of peak measurement parameters on the quality of chiral electrophoretic separations

The effect of nine peak measurement/analysis parameters on chiral capillary electrophoresis (CE), followed by UV detection, was studied. The parameters pertained UV-detection (detection wavelength, reference wavelength, and wavelength bandwidths), signal processing (data acquisition rate, type and amount of filtering) and peak detection (detection threshold and peak width). The influence of these factors on the chiral separation of dimethindene enantiomers was studied at two different concentrations (i.e., at high and low signal-to-noise (S/N) ratio) by the means of experimental designs. The electropherogram characteristics considered were the resolution between the two enantiomers, the peak areas, and the S/N ratio. A D-optimal design was first used as screening design to identify the most critical parameters. Afterwards, a modelling of the different responses as a function of these critical parameters was performed based on the results of a face-centered central composite design. The results showed that the signal-processing parameters should be carefully selected when developing a CE separation since very important variations in the separation, the S/N ratio and the peak area of the substances can occur by setting these parameters at different levels. The detection wavelength should also be carefully chosen for optimal peak area measurement. The role of these parameters becomes more important with decreasing concentration of the analytes (i.e., low S/N ratio). This study showed that the peak measurement/analysis parameters should be optimized as the chemical and physical parameters of a method. They also should always be well specified in order to allow a good transfer of a method from one instrument to another.     

Convenient synthesis of N-methylamino acids compatible with Fmoc solid-phase peptide synthesis

N(alpha)-Methylamino acid containing peptides exhibit interesting therapeutic profiles and are increasingly recognized as potentially useful therapeutics. Unfortunately, their synthesis is hampered by the high price and unavaibility of many N(alpha)-methylamino acids. An efficient and practical preparation of N(alpha)-methyl-N(alpha)-(o-nitrobenzenesulfonyl)-alpha-amino acids without extensive purification is described. The procedure is based on the well-known N-alkylation of N(alpha)-arylsulfonylamino esters which was improved by using dimethyl sulfate and DBU as base. Ester cleavage is efficiently achieved by using an S(N)2-type saponification with lithium iodide, avoiding racemization observed with lithium hydroxide hydrolysis. Compatibility of the synthesized N(alpha)-methylamino acids with Fmoc solid-phase peptide synthesis is demonstrated by using normal coupling conditions to efficiently prepare N-methyl dipeptides. The described procedure allows the preparation of N(alpha)-methylamino acids in a very short period of time and a rapid synthesis of N-methyl peptides using Fmoc solid-phase peptide synthesis.     

Synthesis of phosphorofluoridates and phosphorofluoridothioates via the phosphoramidite approach

We present a very efficient synthetic procedure leading to the phosphorofluoridates RO-P(O)(OH)F 1 or phosphorofluoridothioates RO-P(S)(OH)F 2, which is based on the intermediary of fluorophosphoramidites (RO)P(F)N(i)Pr2 5 [R = 9-(hydroxyethyloxymethyl)guaninyl), 3'azido-3'deoxythymidinyl, thymidinyl, anhydrothymidinyl, cholesteryl, N6-benzoyl-5'-O-(4,4'-dimethoxytrityl)-2'-deoxyadenosinyl]. The activation of the amino group was performed with trimethylchlorosilane (TMCS).