便携式近红外光谱仪对废旧涤/棉混纺织物中涤含量的快速检测

利用近红外光谱技术对252个涤/棉混纺织物进行研究,建立了不同光谱特征的涤/棉混纺织物的偏最小二乘(PLS)定量分析模型。将近红外光谱异常样本与光谱正常样本分别建模,显著提高了定量分析模型的预测精度、拓宽了模型的适用范围。以涤、棉主要吸收峰区间为基本建模波段,进行双向扩展,筛选出最佳建模波段,以相关系数(R)、预测集标准差(SEP)和验证集准确率优化建模条件,并与未分别建模的PLS模型相比较。用346个未参与建模的废旧涤/棉混纺织物对模型进行外部验证,外部验证准确率为92%,识别时间8s。     

近红外光谱法同时测定黄芪精口服液中黄芪多糖和黄芪甲苷的含量

应用傅立叶变换近红外光谱仪透射光谱技术对黄芪精口服液中黄芪多糖(APS)和黄芪甲苷(AGS)的含量进行检测分析,采用偏最小二乘回归法(PLS)建立了黄芪精口服液中APS和AGS含量近红外数学校正模型.通过内部交叉验证,确定了模型的最佳变量数,得到了建立模型的最佳参数,并通过预测集对模型进行了外部验证.黄芪多糖的相关系数...     

校正集样品特性对鼠药中毒鼠强近红外光谱分析的影响

根据市售鼠药样品成分各异且相对复杂,建立6种不同成分体系和9个不同样本容量的校正集,运用小波变换压缩鼠药的近红外透射光谱数据,结合BP反向神经网络算法对压缩的数据进行建模,考察校正集样品特性对模型预测能力的影响。试验结果表明:采用BP神经网络算法建立定量模型时,只要校正集样品中包含了与预测样品性质相似的样本,就能准确地对复杂样品进行近红外定量分析。当校正集容量分别为72和84时,模型预测结果趋于平稳。当校正集数量为96时,模型的最大相关系数为0.959 8,预测最小标准差和平均相对误差分别为1.893%和1.92%。     

近红外光谱与组合的间隔偏最小二乘法测定清开灵四混液中总氮和栀子苷的含量

应用近红外光谱分析技术结合化学计量学方法, 建立了中药清开灵注射液中间体总氮和栀子苷含量测定的新方法. 首先采用Kernard-Stone法对训练集样本和预测集样品进行分类, 然后应用组合的间隔偏最小二乘法(Synergy interval partial least squares, siPLS)对所得近红外透射光谱进行有效谱段范围的选择以及二者定量校正模型的建立, 并对光谱预处理方法进行了详细的讨论. 所建立的总氮和栀子苷校正模型的预测相关系数(R)分别为0.999和0.708; 交叉验证误差均方根(RMSECV)均为0.023; 预测误差均方根(RMSEP)分别为0.074和0.159; 预测结果表明, 本实验所建方法快速、无损且可靠, 可推广并应用于中药注射液中间体的在线质量控制.     

近红外光谱法快速测定溶剂型木器涂料中甲苯、乙苯和二甲苯

建立了使用近红外光谱法(NIR)快速测定溶剂型木器涂料中甲苯、乙苯和二甲苯的方法。收集涂料样品,使用气相色谱法(GC)测定苯系物含量。采用聚乙烯密实袋封装聚氨酯类、硝基类或醇酸类涂料,应用积分球透漫射采样方式采集清漆和漫射采样方式采集色漆的近红外光谱。采用偏最小二乘法,分别建立清漆和色漆的近红外光谱与苯系物线性关系模型。校正集均方差在0.43%~1.32%之间、相关系数R在0.9046~0.9766之间。验证集均方差在0.591%~1.73%之间。对未知样品预测,清漆样品预测值相对偏差<15%;色漆样品预测值相对偏差<20%。两个定量模型预测效果良好。该2个NIR定量方法适用于对溶剂型木器涂料中甲苯、乙苯和二甲苯含量进行快速测定。     

近红外光谱法快速检测何首乌炮制过程中多糖含量的研究

该研究基于近红外光谱技术建立了何首乌在蒸制过程中多糖含量变化的快速定量模型。采用蒽酮-浓硫酸法测定了不同蒸制时间何首乌的多糖含量并结合采集的近红外光谱数据建立模型,以校正集相关系数(R²_c)、预测集相关系数(R²_p)、交叉验证集均方根误差(RMSECV)和预测集均方根误差(RMSEP)作为评价指标,考察了不同预处理方法和变量筛选方法的效果。结果显示,随着蒸制时间的延长,何首乌多糖含量先上升后下降并趋于平稳,采用平滑+变量标准化+随机蛙跳变量筛选建立的偏最小二乘法回归模型的R²_c=0.96,RMSECV=0.74,R²_p=0.96,RMSEP=0.28;外部预测相对偏差小于3.0%。所建立的多糖含量定量模型质量较高,预测能力较强,可为探索何首乌炮制工艺标准化及质量评价提供参考。     

近红外光谱法测定卷烟纸中钠、钾、镁、钙和柠檬酸根的含量

采用近红外光谱法测定卷烟纸中钠、钾、镁、钙和柠檬酸根的含量。用近红外光谱法对163个具有代表性卷烟纸样品进行测定,利用偏最小二乘法建立了卷烟纸中钠、钾、镁、钙和柠檬酸根的数学定量模型。结果表明:当卷烟纸重叠张数为15张及以上时,近红外漫反射扫描光谱无明显差异;各模型相关系数分别为0.949 6,0.982 5,0.958 1,0.930 0,0.987 9;模型交互验证均方根误差分别为0.245,0.415,0.050 5,3.08,0.533;模型外部验证平均相对偏差分别为6.63%,4.87%,6.03%,2.31%,4.58%。t-检验结果表明:5种组分显著性水平均大于0.05,预测值与测定值不存在显著性差异。     

近红外光谱法同时测定通天口服液中天麻素和芍药苷的含量

本文应用近红外光谱结合偏最小二乘法建立了同时测定通天口服液中天麻素与芍药苷含量的方法。以高效液相色谱(HPLC)法测定通天口服液样品中天麻素和芍药苷的化学参考值,随机抽取60个样本作校正集,20个样本作预测集。用偏最小二乘法(PLS)将校正集样本的近红外光谱与相应样本的天麻素和芍药苷含量分别相关联建立模型。结果表明,天麻素和芍药苷校正模型的决定系数分别为96.28%、94.55%,模型的交叉验证均方差分别为0.0336、0.00908,预测集的决定系数分别为94.23%、92.86%,预测集均方差分别为0.0453、0.00839。同时还做了模型的精密度实验,该方法能用于大批量样品的快速分析。     

鲜辣椒中糖份和维生素C含量的近红外光谱非破坏性测定

用近红外光谱法非破坏测定鲜辣椒中可溶性糖和维生素C含量，可溶性糖含量的化学值与近红外预测值之间的相关系数为0．9024，校正集标准差(SEP)为1．23％，RSD9．3％；VC含量的化学值与近红外预测之间的相关系数为0．9122，校正集标准差(SEP)为24．17，RSD为9．5％，辣椒鲜果中可溶性糖和VC含量与近红外光谱有显著的相关关系。     

近红外光谱法测定柴油硫含量方法研究(英文)

近红外分析方法是目前发展较快的一种快速测量方法,它具有快速、准确、无污染等特性,被广泛应用于石油化工各个领域中,而采用近红外分析方法测定硫含量的文献报道较少。本文对近红外分析方法测定柴油硫含量进行了研究。选取有代表性的100个柴油样品,采用多元线性回归法建立校正模型。由17个样品组成验证集,用建立的分析模型预测其硫含量,将近红外光谱测定的结果与标准方法测定的结果进行比较。模型具有较好的相关性,标准偏差为426.95,相关系数是0.998。     

近红外光谱法快速分析有机肥料中有机质、总养分和pH值

建立了近红外光谱法结合偏最小二乘(PLS)法测定126种有机肥料中有机质、总养分和p H值的快速方法。采用K–S法分类,选取S–G平滑、S–G导数、多元散射校正和均值平均化4种前处理方法对粉碎后样品的近红外光谱信息进行预处理,以PLS法建立定量分析模型。结果表明,有机肥料中总养分的RC,SEC,RP,SEP,RPD分别为0.990,1.272%,0.985,1.084%,5.9;p H值的RC,SEC,RP,SEP,RPD分别为0.910,0.344%,0.737,0.428%,2.9。有机质项目根据国标方法分为小于40%、小于55%和大于55%3种样品进行分析,3种样品的RP分别为1.000,0.989,1.000;RPD分别为18.9,17.5,8.8。对比国标方法,有机质和总养分的测定精度满足实验室精确分析要求,p H值测定法可用于定量分析。NIR–PLS法实现了对有机肥料进行无损快速的检测分析。     

白酒基酒中酮类物质的近红外光谱检测方法

应用近红外光谱技术建立了白酒基酒中2,3-丁二酮和3-羟基-2-丁酮的快速检测模型。从洛阳杜康酒厂选取182个白酒基酒样品为材料,运用气相色谱法测得两种物质的化学值,同时采集其在12 000~4 000 cm-1范围内的光谱数据,采用偏最小二乘法(PLS)结合内部交叉验证建立校正模型。通过对比不同光谱预处理下PLS模型效果对其进行优化,确定2,3-丁二酮和3-羟基-2 丁酮的最佳预处理方法分别为一阶导数+多元散射校正和二阶导数,最佳光谱区间分别为9 403.2~7 497.9 cm-1和9 403.2~7 497.9 cm-1+6 101.7~5 449.8 cm-1。优化后2,3-丁二酮和3 羟基-2-丁酮校正集样品的化学值和近红外预测值的决定系数(R2)分别为0.960 2和0.963 2,交叉验证均方根误差(RMSECV)分别为0.39、0.22 mg/100 mL;通过外部检验,验证集样品的R2分别为0.957 6和0.957 8,预测均方根误差(RMSEP)分别为0.40、0.24 mg/100 mL。结果表明,应用近红外光谱技术结合化学计量学方法所建立的模型有较高的准确度,能够满足白酒生产中酮类物质的快速检测需要。     

ICA方法与NIR技术用于药片中活性成分含量的测定

用独立分量分析(ICA)方法提取药片近红外光谱数据矩阵的独立成分和相应的混合矩阵, 再用BP神经网络对混合矩阵和药片中活性成分的浓度矩阵进行建模, 提出了新的药片活性成分含量测定的基于独立分量分析-神经网络回归(ICA-NNR)的近红外光谱分析方法. 通过分析独立分量数和网络中间隐层的神经元数对模型性能的影响, 分别建立三类药片定量分析的最优模型. 该方法用于实测的三类药片中活性成分含量的测定, 测试样品集的化学检测值与近红外预测值的相关系数分别达到0.962, 0.980及0.979. 结果表明, 基于ICA-NNR的近红外光谱分析方法对制药业的药片进行定量分析是可行的.     

Quantitative Analysis of Uncoated Eszopiclone Tablets by Near-Infrared Spectroscopy

This study employed near-infrared (NIR) spectroscopy to analyze content uniformity, moisture content, compression force, tablet hardness, average particle size, and particle-size distribution. The content uniformity, moisture content, compression force, tablet hardness, and average particle size models yielded high correlation coefficients (R²) of 0.99582, 0.99725, 0.99620, 0.96294, and 0.98421, respectively, whereas the particle size distribution models showed good predictive ability. Conventional criteria such as R², root-mean-square error of calibration, and the root-mean-square error of prediction were used to evaluate the accuracy and precision of the model. To ensure the accuracy and predictability of the content model for low-dose tablets, additional validation and reliability evaluations were performed using 70%, 80%, 100%, 120%, and 130% drug concentrations as well as 90% and 110% active content formulations. Near-infrared spectroscopy with multivariate modeling is a rapid, nondestructive technique for the characterization of the manufacturing process.     

Determination of Nitrogen in Rapeseed by Fourier Transform Infrared Photoacoustic Spectroscopy and Independent Component Analysis

Fourier-transform mid-infrared photoacoustic spectroscopy was utilized for rapid and nondestructive determination of nitrogen in rapeseeds. Rapeseed spectra were characterized by independent component analysis for quantitative calibration. A calibration model was built by using independent components as the input for partial least squares. Compared to full-spectrum partial least squares, the combined model achieved higher prediction accuracy with a residual predictive deviation of 2.06. Moreover, a genetic algorithm coupled with partial least squares was adopted to optimize the independent components for partial least square modeling and provide a further refined model with the highest residual predictive deviation of 2.12. A t-test verified a high congruence between results obtained by calibration models and the reference Kjeldahl method. This study demonstrated the promise of Fourier-transform mid-infrared photoacoustic spectroscopy for the determination of nitrogen in rapeseeds and the applicability of independent components for multivariate calibration.     

近红外光谱测定聚四氢呋喃混合液

近红外光谱;聚合反应;过程分析;四氢呋喃;分子质量     

Direct, non-destructive quantitative measurement of an active pharmaceutical ingredient in an intact capsule formulation using Raman spectroscopy

The active pharmaceutical ingredient (ambroxol) in an intact capsule formulation has been non-destructively quantified using Raman spectroscopy. To improve the problem of insufficient representive sampling inherent in Raman measurements, we have employed a wide area illumination (WAI) scheme that enables much improved sample coverage through a circular excitation laser spot with a 6 mm diameter. One of the anticipated sources of variation for this measurement was variation in the capsule shells. However, the WAI scheme significantly decreased the spectral variation among empty capsules compared to a measurement with a traditional small-spot excitation. Therefore, measurement variations emanating from the capsule shell did not significantly influence the accuracy of the determination of ambroxol concentrations. The resulting standard error of prediction (SEP) using the WAI scheme was comparable to that from previous Raman measurements which used a conventional small-spot excitation and employed a sampling scheme that involved rotation of an ambroxol pellet. It is further noteworthy that the SEP was also similar to that obtained from the use of transmission NIR spectroscopy, which was achieved by collection of spectra of the powdered capsule contents removed from the shell. The proposed Raman measurement using the WAI scheme in this case was sufficient to achieve the quantitative measurement of the active pharmaceutical ingredient (API) content of capsules non-destructively.     

Evaluation and comparison of mid-infrared,Raman and near-infrared spectroscopies for characterization and determination of the compositions in fully biodegradable poly(lactic acid)/poly(propylene carbonate)/poly(butylene adipate-co-terephthalate) blends combined with chemometrics

In this work, mid-infrared (MIR), Raman and near-infrared (NIR) spectroscopies were evaluated and compared for characterization and determination of the compositions in poly(lactic acid)/poly(propylene carbonate)/poly(butylene adipate-co-terephthalate) (PLA/PPC/PBAT) blends via chemometrics. Qualitative analysis of MIR, Raman, and NIR spectra of the three compositions was performed. Partial least squares (PLS) models were developed based on each spectroscopy for quantitative determination of the concentrations. The data suggested that MIR and Raman have an advantage over NIR in terms of qualitative recognition of the three compositions. The data also showed that Raman and NIR succeeded in determining the concentrations, while the concentration determined via MIR was inaccurate. Hence, Raman is the optimal analytical tool for qualitative characterization and quantitative determination of the compositions in fully biodegradable PLA/PPC/PBAT blends. The characteristic bands in the Raman spectra clearly identify PLA, PPC, and PBAT to be 392 cm^?1 (δ CCO), 948 cm^?1 (ν C?O?C) and 1600 cm^?1 (ν C ? C in benzene ring), respectively. The optimal calibration models based on Raman for PLA, PPC, and PBAT exhibited root mean square error of prediction (RMSEP) values of 3.140%, 3.576%, and 2.538%, respectively.     

Expanding the analytical toolbox for identity testing of pharmaceutical ingredients: Spectroscopic screening of dextrose using portable Raman and near infrared spectrometers

In the pharmaceutical industry, dextrose is used as an active ingredient in parenteral solutions and as an inactive ingredient (excipient) in tablets and capsules. In order to address the need for more sophisticated analytical techniques, we report our efforts to develop enhanced identification methods to screen pharmaceutical ingredients at risk for adulteration or substitution using field-deployable spectroscopic screening. In this paper, we report our results for a study designed to evaluate the performance of field-deployable Raman and near infrared (NIR) methods to identify dextrose samples. We report a comparison of the sensitivity of the spectroscopic screening methods against current compendial identification tests that rely largely on a colorimetric assay. Our findings indicate that NIR and Raman spectroscopy are both able to distinguish dextrose by hydration state and from other sugar substitutes with 100% accuracy for all methods tested including spectral correlation based library methods, principal component analysis and classification methods.