Complexation between poly(acrylic acid) and poly(vinylpyrrolidone): Influence of the molecular weight of poly(acrylic acid) and small molecule salt on the complexation

Poly(acrylic acid) (PAA) with different molecular weight and poly(vinylpyrrolidone) (PVP) were prepared by free radical polymerization using 2,2′-azoisobutyronitrile (AIBN) as initiator in anhydrous methanol for PAA, and in distilled water for PVP. Then, the complexation between PAA and PVP in aqueous solution was studied by UV transmittance measurement and fluorescence probe technique. The result shows that (1) at low pH, the formation of complexation between PAA and PVP bases on the intermacromolecular hydrogen bond and the composition of the formed complex is around 3:2 (the unit molar ratio of PAA to PVP) at pH 2.60 over the range of pH investigated. (2) The cooperative interaction through the formation of hydrogen bond among active sites plays an important role in complex formation, and depends on the pH of solution, the required minimum chain length of poly(acrylic acid). (3) The hydrogen bond is not affected by small molecular salt, which only affects those carboxylic groups without forming hydrogen bond on the PAA chain.     

PH effects in the complex formation and blending of poly(acrylic acid) with poly(ethylene oxide)

The effect of pH on the complex formation between poly(acrylic acid) (PAA) and poly(ethylene oxide) (PEO) has been studied in aqueous solutions by turbidimetric and fluorescent methods. It was shown that the formation of insoluble interpolymer complexes is observed below a certain critical pH of complexation (pH(crit1)). The formation of hydrophilic interpolymer associates is possible above pH(crit1) and below a certain pH(crit2). The effects of polymer concentrations in solution and PEO molecular weight as well as inorganic salt addition on these critical pH values were studied. The polymeric films based on blends of PAA and PEO were prepared by casting from aqueous solutions with different pHs. These films were characterized by light transmittance measurements and differential scanning calorimetry. The existence of the pH value above which the polymers form an immiscible blend was demonstrated. The transitions between the interpolymer complex, miscible blend, and immiscible blend caused by pH changes are discussed. The recommendations for preparation of homogeneous miscible films based on compositions of poly(carboxylic acids) and various nonionic water-soluble polymers are presented.     

Complexation between poly(N,N-diethylacrylamide) and poly(acrylic acid) in aqueous solution

The complexation between poly(N,N-diethylacrylamide) (PDEA) and poly(acrylic acid) (PAA) in aqueous solution was studied by viscometric, potentiometric, and fluorescence techniques. It was found that an interpolymer complex formed between the two polymers through hydrogen bonding interactions with the stoichiometry of r=0.6 (r is unit molar ratio of PAA/PDEA), and the complex formation show the dependence on pH values. The phase behaviour studies showed that the lower critical solution temperature of the PDEA-PAA aqueous solution gradually increased with the increasing of r from 0.01 to 0.15, until a soluble system in the whole temperature region was obtained, which remained in the range of r=0.15-0.3. At higher PAA concentrations, when r is above 0.3, the system appeared phase separation, and almost no temperature dependence was observed. Based on these conclusion and structure characteristics of PDEA and PAA, a model containing only short sequences of monomer residues was proposed for the structure of PDEA-PAA complex.     

Binding of a surfactant counterion to low-charge-density poly(acrylic acid) and poly(methacrylic acid)

The binding of a cationic surfactant, dodecylpyridinium (C12Py) chloride, with a low-charge-density poly (methacrylic acid) (PMA) was investigated in buffer solutions under the condition of constant pH. The binding isotherms with PMA consisted of two and three steps at a pH lower and higher than 3.2, respectively. Bindings in the first step were independent of pH and this step was considered to correspond to the solubilization of the hydrocarbon chains of C12Py into the nonpolar region of the compact form of PMA. This is the indication of the compact form from the binding isotherm. At pH higher than 3.2, the second step was discriminated and it depended on the pH. In the third step, a sharp rise in the degree of binding (β) was observed accompanying the solubilization of the precipitates of the PMA–C12Py complex. The binding with poly(acrylic acid) (PAA) and PMA in conventional unbuffered NaCl solutions was also examined and the pH profile of the solution during the binding process was determined. In the case of unbuffered NaCl solutions, the binding with PAA took place cooperatively at the critical association concentration (cac). The binding isotherm consisted of two steps and the pH decreased with the increase in β. The binding isotherm of PMA, on the other hand, consisted of three steps: the pH decreased slightly in the first step and considerably in the second step with the increase in β but it increased with β in the third step, exhibiting a pH minimum around 3.2. The binding in the first step coincided with that obtained in the buffered solutions. Linear relationships between β and the pH were found for both polymers. In the case of PMA, no cac was observed in both buffered and unbuffered NaCl solutions. Received: 24 January 2001 Accepted: 23 May 2001     

Hydrogen bonded layer-by-layer assembly of poly(2-vinylpyridine) and poly(acrylic acid): Influence of molecular weight on the formation of microporous film by post-base treatment

This article describes the buildup of hydrogen bonded multilayer film of poly(2-vinylpyridine) (P2VP) and poly(acrylic acid) (PAA), and the influence of polymer molecular weight on the formation of microporous film by post-base treatment. The formation of a microporous film involved a two-step mechanism: the release of PAA from P2VP/PAA multilayer, and the reorganization of the remaining P2VP on the substrate. Fourier transform infrared spectroscopy (FT-IR) indicated that the release of PAA from hydrogen bonded multilayer was a rapid process, which was almost independent of the molecular weight of PAA. Furthermore, the molecular weight of P2VP had a great effect on micropore formation by immersing the P2VP/PAA multilayer in basic solution. The rate of micropore formation increased with increasing molecular weight. We anticipate that a comparative study on P2VP/PAA films containing high or low molecular weight polymer provides a way to control the surface morphology, and will be helpful and constructive for the forthcoming discussion about the formation of the microporous film.     

Preparation and characterization of poly(acrylic acid)-based nanoparticles

The present investigation describes the synthesis and characterization of nanoparticles based on poly(acrylic acid) (PAA) intramolecularly cross-linked with diamine, 2,2′-(ethylenedioxy)bis(ethylamine), using water-soluble carbodiimide. The aqueous colloid dispersions of nanoparticles were clear or mildly opalescent depending on the ratio of cross-linking, pH of the solution, and the molecular weight of PAA, finding consistent with values of transmittance between 3% and 99%. The structure was determined by nuclear magnetic resonance spectroscopy, and the particle size was identified by dynamic light scattering (DLS) and transmission electron microscopy (TEM) measurements. It was found that particle size depends on the pH, and at a given pH, it was caused by the ratio of cross-linking and the molecular weight of PAA. Particle size measured by TEM varied in the range of 20 and 80 nm. In the swollen state, the average size of the particles measured by DLS was in the range of 35–160 nm.     

Interpolymer complexes of poly(acrylic acid) with poly(2-hydroxyethyl acrylate) in aqueous solutions

Complexes formed from poly(acrylic acid) and poly(2-hydroxyethyl acrylate) were studied in aqueous solutions by viscometric, turbidimetric, FTIR spectroscopic, and thermogravimetric analysis methods. The formation of interpolymer complexes stabilized by hydrogen bonds was observed. It was found that the compositions of these interpolymer complexes are strongly dependent on the concentration of polymers, the order of mixing the solutions, and the pH. It was demonstrated that the complexation ability of poly(2-hydroxyethyl acrylate) is relatively low compared to other known nonionic water-soluble polymers. However, it can be significantly increased via hydrophobic modification of the poly(acrylic acid) using cetyl pyridinium bromide.     

Polyelectrolyte complexes of soluble poly-2-[(methacryloyloxy)ethyl]trimethylammonium chloride and its hydrogels with poly(acrylic acid)

The complex formation of poly-2-[(methacryloyloxy)-ethyl]trimethylammonium chloride (PMADQUAT) with poly(acrylic acid) (PAA) of different molecular weights has been studied in aqueous solutions by potentiometric, viscometric, turbidimetric and FTIR spectroscopic methods. The formation of insoluble non-stoichiometric polyelectrolyte complexes has been shown. The stability of polyelectrolyte complexes in solutions of different pH and ionic strength has been evaluated. The formation of polyelectrolyte complexes between hydrogels of PMADQUAT and linear PAA of different molecular weights has been studied. It was shown that the molecular weight of PAA considerably affects the kinetics of interaction as well as the final state of gel-polymer complex.     

Complexation of poly(acrylic acid) and poly(ethylene oxide) investigated by enhanced Rayleigh scattering method

The method of enhanced Rayleigh scattering spectroscopy (ERS) was developed to investigate the complexation of poly(acrylic acid) (PAA) and poly(ethylene oxide) (PEO) in semidilute polymer solutions. Based on the Ornstein‐Zernike equation, the relationship between macromolecular static correlation length and ERS intensity was presented. Moreover, the ERS spectra were calculated by the moving window two‐dimensional (MW2D) correlation spectroscopy to get detailed information of the polymer complexation. The results indicated that the ERS spectroscopy characteristics of the polymer mixtures have similar trend, and the ERS intensity promptly increases as the macromolecular chains contract. The increase of ERS intensity showed that the degree of complexation between PAA and PEO increases when the pH value decreases. The complexation results from the collapse of macromolecular chains, which is induced by the PAA chains contracting and the enhanced association between PAA and PEO chains because of the hydrogen bond formation. In addition, the association resulting from the complexation of PAA and PEO in solution was demonstrated by the MW2D correlation spectroscopy. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1847–1852, 2010     

聚丙烯酸/聚氧化乙烯高分子复合溶液的结构与粘度

通过溶液折光指数和粘度测定,研究了聚丙烯酸（ＰＡＡ）与聚氧化乙烯（ＰＥＯ）高分子链间在复合溶液中的相互作用和ＰＡＡ／ＰＥＯ高分子氢键复合溶液的结构与粘度,研究了复合溶液粘度随溶液ｐＨ值的变化规律及不同浓度时剪切速率对复合溶液粘度和复合增粘效果的影响。结果表明：ＰＡＡ／ＰＥＯ复合溶液结构不同于ＰＡＡ和ＰＥＯ两组分聚合物溶液结构,ＰＡＡ与ＰＥＯ高分子链间的氢键相互作用形成构象更为伸展、流体力学体积列大     

The synthesis and characterization of monodisperse poly(acrylic acid) and poly(methacrylic acid)

A number of polyacrylic (PAA) and polymethacrylic (PMAA) acids have been synthesized by living anionic polymerization of the monomeric tert-butyl esters followed by subsequent hydrolysis of the corresponding polyesters. The necessary precautions were taken in order to assure good molecular weight control, as well as high yields in the polymerization reactions. The intermediate and final polymers were characterized by gel permeation chromatography and NMR-H¹ spectrometry.     

聚丙烯酸在纳米TiO2表面吸附行为的研究

讨论了聚丙烯酸在纳米TiO₂水悬浮体系中的吸附行为.红外光谱分析和吸附实验结果表明,纳米TiO₂通过氢键吸附PAA.PAA吸附量随着浓度的升高而增大直至饱和吸附量,且分子量越大,饱和吸附量越大.pH值增大,则饱和吸附量减小.在相同条件下,表面吸附层的厚度随PAA分子量、浓度和pH值增大而增大.这是由PAA在颗粒表面构型的变化所致.吸附PAA后的纳米TiO₂的表面电荷密度和ζ电位发生变化,pHiep值向低值方向移动.表面吸附自由能的计算结果说明,PAA在纳米TiO₂表面的吸附是自发过程.     

Interpolymer complexes of copolymers of vinyl ether of diethylene glycol with poly(acrylic acid)

 The complex formation reactions of poly(vinyl ether of diethylene glycol) as well as vinyl ether of diethylene glycol–vinyl butyl ether copolymers with poly(acrylic acid) have been studied in aqueous and alcohol solutions. The formation of interpolymer complexes which were stabilized by hydrogen bonds was shown. The effects of molecular weight of poly(acrylic acid) and the nature of the nonionic polymer on the composition and stability of interpolymer complexes were clarified. The critical pH values of complexation were determined for different systems with various molecular weights and hydrophobic–hydrophilic balances. The stability of the interpolymer complexes formed in aqueous and alcohol solutions with respect to dimethylformamide addition was evaluated. The role of hydrophobic interactions and the presence of active groups on stability of the interpolymer complexes is discussed. Received: 23 July 2001 Accepted: 27 September 2001     

Adsorption mechanism and dispersion efficiency of three anionic additives [poly(acrylic acid), poly(styrene sulfonate) and HEDP] on zinc oxide

Adsorption on ZnO of sodium poly(acrylate) (PAA), sodium poly(styrene sulfonate) (PSS) and a monomer surfactant [hydroxyethylidene diphosphonate (HEDP)] was investigated in suspensions initially equilibrated at pH 7. Results demonstrate interplay in the adsorption mechanism between zinc complexation, salt precipitation, and ZnO dissolution. In the case of PAA, the adsorption isotherm exhibits a maximum attributed to the precipitation of zinc polyacrylate. PSS and HEDP formed high-affinity adsorption isotherms, but the plateau adsorption of HEDP was significantly lower than that of PSS. The adsorption isotherm of each additive is divided into two areas. At low additive concentration (high zinc/additive ratio), the total zinc concentration in the solution decreased and the pH increased upon addition. At a higher additive ratio, zinc concentration and pH increased with the organic concentration. The increase in pH is due to the displacement of hydroxyl ions from the surface and the increase in zinc concentration results from the dissolution of ZnO due to the complexation of zinc ions by the organics. The stability of the ZnO dispersions was investigated by measurement of the particle size distribution after addition of various amounts of polymers. The three additives stabilized the ZnO dispersions efficiently once full surface coverage was reached.     

Low molecular weight poly(acrylic acid) as a salt scaling inhibitor in oilfield operations

Poly(acrylic acid) (PAA) samples with molecular weights between 820 and 2950 were synthesized by a solution polymerization process using an initiating redox system. The obtained PAAs were then screened for their ability to inhibit salt scale formation. In this screening system, salt scale was formed by injecting pit water into the oil. The salt scale inhibition efficiency was higher for PAAs at a higher concentration and for lower molecular weight PAAs. A reduction of pH, extension of stirring time, or an increase in temperature caused the inhibition efficiency of the PAAs to drop. An optimal inhibition efficiency of 98.70% was observed using a PAA with a molecular weight of 820 at a concentration of 20 ppm, at 20 °C, while being stirred for 1 h at a pH of 6.029.     

Interpolymer complex between poly(ethylene oxide) and poly(carboxylic acid)

An interpolymer complex was prepared by mixing aqueous solutions of poly(ethylene oxide) (PEO) and of a poly(carboxylic acid), i.e., poly(acrylic acid)(PAA), poly(methacrylic acid)(PMAA), or styrene-maleic acid copolymer(PSMA). The complexation mechanism was discussed on the basis of results of such experimental methods as viscosity, potentiometric titration, and turbidimetry. The hydrogen bond is primarily involved in these complexations, but the influence of hydrophobic interaction on complexation can not be ignored. If the degree of dissociation α of carboxylic acid or the degree of polymerization P_n of PEO was perceptibly changed, a stable complex was obtained at about α 0.1 or P_n (PEO) = 40 for PMAA, 200 for PAA. This fact indicates that more than a definite number of binding sites are necessary for a stable interpolymer complex to be formed and that cooperative interaction among active sites plays an important role in complex formation.     

Characterization of poly(carboxylic acid)/poly(ethylene oxide) blends formed through hydrogen bonding by spectroscopic and calorimetric analyses

The solid state of the complex between poly(acrylic acid) (PAA) and poly(ethylene oxide) (PEO), and that between poly(methacrylic acid) (PMAA) and PEO formed via hydrogen-bonding was studied by differential-scanning calorimetric (DSC) and by Fourier-transform infrared (FT–IR) spectroscopic measurements. Melting temperature T_m and the degree of the crystallinity X_c of PEO in the systems PAA (or PMAA)/PEO blends obtained from aqueous or dimethyl sulfoxide (DMSO) medium were measured in various unit mol % of PEO ([PEO]100/{[PAA(or PMAA)] + [PEO]}) where [ ] is the unit mole concentration. It was found that 50 unit mol % of PEO is a critical composition, which gives new evidence for the 1 : 1 complex formation between PAA (or PMAA) and PEO. From the FT–IR spectroscopic analysis in conjunction with DSC measurements we also found that the effects of solvent and of hydrophobic interaction (due to the α-methyl group of PMAA) are the important factors controlling the complexation in the solution and solid systems. These factors also affect the crystallization behavior and the microstructure of the PAA (or PMAA)/PEO blend in solid state.     

Surface modification of glass beads with poly(acrylic acid)

Non‐porous P₂ glass beads were etched with sodium hydroxide to increase the number of silanol groups that could be used to modify the surface. The etched glass beads were then functionalized with 3‐aminopropyltriethoxysilane (APS) and/or glycidoxypropyltrimethoxysilane (GPS). The surface of the glass beads were further modified with poly(acrylic acid) (PAA) by reacting the carboxyl groups on PAA with the amino groups of the pregrafted APS. The chemical modifications were characterized by FT‐IR spectroscopy, particle size analyzer and tensiometry for contact angle and porosity measurements. Five different molecular weight PAA polymers ranging from 2000 to 3,000,000 were grafted with less than expected increase of grafted PAA with molecular weight. The amount of APS and PAA on the surface was determined from thermogravimetric analysis and elemental analysis data. The surface properties of the surface modified glass beads were determined by measuring water and hexane penetration rate and contact angle. The surface morphology was examined by scanning electron microscopy. Copyright © 2006 John Wiley & Sons, Ltd.     

Molecular weight influence on viscosimetric parameters of poly(4-vinylpyridine) polymers

This work describes the effect of the molecular weight on the viscosimetric parameters of poly(4-vinylpyridine) (P4VP) polymers in ethanolic solution. Numerous studies concerning this question have been reported in very separate intervals of molecular weight. We have observed a discordance (discontinuity) in the variation of the intrinsic viscosity as a function of the molecular weight of these polymers ([η]=f(M_w)). In order to establish a general relationship between viscosimetric parameters and M_w, we have considered 10 P4VP samples in a wide interval of molecular weights: 0.75×10⁴ to 153×10⁴. These results have been compared and completed with that of the literature. We have observed that:

(i)

All viscosimetric parameters (intrinsic viscosity [η], Huggins constant k_H, second virial coefficient, viscosimetric expansion coefficient α_η, and critical concentration) change according to a continuous function without a break.

(ii)

The lower is the molecular weight of P4VP; the higher are the variations of the expansion coefficient and the interaction effects.

(iii)

The variation of the intrinsic viscosity versus the molecular weight follows a unique relation in the whole M_w range. In fact, the Berkowitz equation (1), described for a limited range of relatively high M_w (10⁵ to 18.5×10⁵) is extended for all M_w interval values.

(iv)

Empiric laws for [η], k_H, A₂ and C^* and variations as a function of molecular weight were proposed for the P4VP in ethanol.

     

Studies on interpolymer self-organisation behaviour of protoporphyrin IX bound poly(carboxylic acid)s with complimentary polymers by means of fluorescence techniques

Covalently bound protoporphyrin IX was used as a fluorophore to investigate the interpolymer complex formation between the poly(carboxylic acid)s, PMAA/PAA and poly(N-vinyl pyrrolidone), PVP, poly(ethylene oxide), PEO or poly(ethylene glycol), PEG. Absorption and emission spectral properties of protoporphyrin IX bound to PAA, PMAA and PVP have been studied. Protoporphyrin IX in poly(MAA-co-PPIX) was found to be present in the dimer or higher aggregated form at low pH due to the environmental restriction imposed by the polymer whereas in the case of poly(AA-co-PPIX) and poly(VP-co-PPIX), PPIX exists in monomeric form. The fluorescence intensity and lifetime of PPIX bound to poly(carboxylic acid)s increase on complexation through hydrogen bonding with PVP, PEO and PEG due to the displacement of water molecules in the vicinity of the PPIX. Poly(MAA-co-PPIX) shows longer fluorescence lifetime due to the more compact interpolymer complexation as compared to poly(AA-co-PPIX) due to the enhanced hydrophobicity of PMAA. Poly(VP-co-PPIX) shows a decrease in the fluorescence lifetime on complexation with PMAA or PAA due to the hydrophilic and microgel like environment of the fluorophore bound to PVP. The contrasting behaviour of the same polymer adduct with respect to the site of the fluorophore is interpreted to be due to the solvent structure which determines the environment of the fluorophore.