Synthesis of polyimide and poly(imide-benzoxazole) in polyphosphoric acid

A polyimide made from 4,4′-diaminodiphenyl ether (ODA) and 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA) was synthesized in polyphosphoric acid. Although the polymerization proceeded heterogeneously, a polyimide with an inherent viscosity of 0.90 was obtained, and a tough and flexible film was made from this polyimide. This polymerization was a one-step reaction including polycondensation and imidization; this was also confirmed by a model reaction between aniline and phthalic anhydride. Utilizing this polymerization method, 3,3′-dihydroxy-4,4′-diaminobiphenyl and 2 mol of 4-aminobenzoic acid were reacted in PPA, then BPDA was reacted to obtain an alternate copolymer containing imide and oxazole rings. This reaction gave a homogeneous solution of the poly(imide-benzoxazole). © 1993 John Wiley & Sons, Inc.     

Complexation between poly(acrylic acid) and poly(vinylpyrrolidone): Influence of the molecular weight of poly(acrylic acid) and small molecule salt on the complexation

Poly(acrylic acid) (PAA) with different molecular weight and poly(vinylpyrrolidone) (PVP) were prepared by free radical polymerization using 2,2′-azoisobutyronitrile (AIBN) as initiator in anhydrous methanol for PAA, and in distilled water for PVP. Then, the complexation between PAA and PVP in aqueous solution was studied by UV transmittance measurement and fluorescence probe technique. The result shows that (1) at low pH, the formation of complexation between PAA and PVP bases on the intermacromolecular hydrogen bond and the composition of the formed complex is around 3:2 (the unit molar ratio of PAA to PVP) at pH 2.60 over the range of pH investigated. (2) The cooperative interaction through the formation of hydrogen bond among active sites plays an important role in complex formation, and depends on the pH of solution, the required minimum chain length of poly(acrylic acid). (3) The hydrogen bond is not affected by small molecular salt, which only affects those carboxylic groups without forming hydrogen bond on the PAA chain.     

Magnetically loaded poly(methyl methacrylate-co-acrylic acid) nano particles

Magnetically loaded polymeric nano-particles carrying functional groups on their surface were prepared by a two-stage process. In the first stage, super-paramagnetic magnetite (Fe₃O₄) nano-particles were produced by a co-precipitation method from the aqueous solutions of FeCl₂·4H₂O and FeCl₃·6H₂O using a NaOH solution. The smallest size obtained was 40.9 nm with poly-dispersity index of 0.194 obtained by using a Zeta Sizer. The effects of Fe²⁺/Fe³⁺ molar ratio, stirring rate, temperature, base concentration, and pH on the particle size/size distribution and stability of the dispersions were examined. Increasing the relative concentration of Fe²⁺ ion and decreasing the stirring rate and pH increased the particle size, while the concentration of NaOH and temperature did not change the particle size significantly. Polymer coating was achieved by emulsion polymerization at high surfactant to monomer ratio of methyl methacrylate (MMA) and acrylic acid which were used as comonomers (comonomer ratio: 90/10 weight) with high surfactant to monomer ratio. The surfactant and initiator were SDS and KPS, respectively. Nano-particles in the range of 115 and 300 nm in diameter were produced depending on recipe. Increasing the Fe₃O₄/monomer and surfactant/monomer ratios, the KPS concentration caused a decrease in the average diameter. Magnetic properties of the nano-particles were obtained by electron spin resonance and vibrating-sample magnetometer. Most of the polymer-coated nano-particles exhibited super paramagnetic behavior.An erratum to this article can be found at     

Modified cotton fabrics with poly (3-(furan-2-carboamido) propionic acid) and poly (3-(furan-2-carboamido) propionic acid)/gelatin hydrogel for UV protection,antibacterial and electrical properties

This research aimed to prepare smart cotton fabrics with multi functions for antibacterial activity, UV protection and electrical conductivity via in situ coating with conductive polymer and conductive hydrogel. Therefore, 3-(furan-2-carboamido) propionic acid was synthesized followed by polymerization using ceric ammonium nitrate. In addition, cotton fabrics coated with 3-(furan-2-carboamido) propionic acid via in situ polymerization and by the hydrogel that based on poly (3-(furan-2-carboamido) propionic acid) and gelatin which have been performed via in situ gelation process. The chemical structure and morphology of the 3-(furan-2-carboamido) propionic acid (monomer) and the synthesized polymer (PFu) were investigated by H¹NMR, IR, SEM, TGA and DSC. Where, the treated fabrics (PFu-T and PFu-G-T) are characterized by SEM, FTIR and contact angle. Furthermore, the AC electrical conductivity and dielectric properties of PFu, PFu-T, PFu-G-T and blank were investigated over the frequency range of 20 Hz–10 MHz at room temperature using impedance spectroscopy where the electric conductivity values are 1.74 × 10^-5, 7.5 × 10^-8, 4 × 10^-7, 8.24 × 10^-11 (S·cm)^-1, respectively. In addition, the anti-bacterial activity of PFu-T, PFu-G-T and blank was assessed versus gram-positive and gram-negative bacteria where, PFu-G-T shows activity against Escherichia coli and Staphylococcus aureus. Moreover, PFu-T, PFu-G-T showed high UV protection especially for PFu-G-T.     

Synthesis and characterization of poly(vinylpyrrolidone-co-vinylphosphonic acid) copolymers

Radical copolymerizations of 1-vinyl-2-pyrrolidone (VP) with vinylphosphonic acid (VPA) at different feed ratios were investigated. The copolymers were characterized by ¹H-NMR, ¹³C-NMR and FT-IR. The copolymer composition was determined from the elemental analysis. Thermogravimetric analysis (TG) illustrates that the copolymers are stable up to 200 °C. Temperature dependence of the alternating current (AC) conductivities were investigated by means of impedance spectroscopy. The direct current (DC) conductivities of the samples are derived from the AC conductivity data.     

New architectures of poly(ethylene glycol) and poly(methylthiirane) in block copolymers

Two synthetic ways were experimented to prepare new architectures of block copolymers made of poly(ethylene glycol) (PEG) and poly(methylthiirane). The coupling of both blocks conveniently end-capped as well as anionic polymerization of methylthiirane initiated by PEG-thiols gave readily the copolymers. Their characterization by ¹H NMR, SEC and IR confirmed the expected structures.     

Synthesis of star‐shaped poly(D,L‐lactic acid‐alt‐glycolic acid)‐b‐poly(L‐lactic acid) with the poly(D,L‐lactic acid‐alt‐glycolic acid) macroinitiator and stannous octoate catalyst

Two types of three‐arm and four‐arm, star‐shaped poly(D,L ‐lactic acid‐alt‐glycolic acid)‐b‐poly(L ‐lactic acid) (D,L ‐PLGA50‐b‐PLLA) were successfully synthesized via the sequential ring‐opening polymerization of D,L ‐3‐methylglycolide (MG) and L ‐lactide (L ‐LA) with a multifunctional initiator, such as trimethylolpropane and pentaerythritol, and stannous octoate (SnOct₂) as a catalyst. Star‐shaped, hydroxy‐terminated poly(D,L ‐lactic acid‐alt‐glycolic acid) (D,L ‐PLGA50) obtained from the polymerization of MG was used as a macroinitiator to initiate the block polymerization of L ‐LA with the SnOct₂ catalyst in bulk at 130 °C. For the polymerization of L ‐LA with the three‐arm, star‐shaped D,L ‐PLGA50 macroinitiator (number‐average molecular weight = 6800) and the SnOct₂ catalyst, the molecular weight of the resulting D,L ‐PLGA50‐b‐PLLA polymer linearly increased from 12,600 to 27,400 with the increasing molar ratio (1:1 to 3:1) of L ‐LA to MG, and the molecular weight distribution was rather narrow (weight‐average molecular weight/number‐average molecular weight = 1.09–1.15). The ¹H NMR spectrum of the D,L ‐PLGA50‐b‐PLLA block copolymer showed that the molecular weight and unit composition of the block copolymer were controlled by the molar ratio of L ‐LA to the macroinitiator. The ¹³C NMR spectrum of the block copolymer clearly showed its diblock structures, that is, D,L ‐PLGA50 as the first block and poly(L ‐lactic acid) as the second block. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 409–415, 2002     

Structural characterization of a poly(methacrylic acid)-poly(methyl methacrylate) copolymer by nuclear magnetic resonance and mass spectrometry

Mass spectrometry (MS) and nuclear magnetic resonance (NMR) have been combined to achieve the complete microstructural characterization of a poly(methacrylic acid)-poly(methyl methacrylate) (PMAA-PMMA) copolymer synthesized by nitroxide-mediated polymerization. Various PMAA-PMMA species could be identified which mainly differ in terms of terminaisons. ¹H and ¹³C NMR experiments revealed the structure of the end-groups as well as the proportion of each co-monomer in the copolymers. These end-group masses were further confirmed from m/z values of doubly charged copolymer anions detected in the single stage mass spectrum. In contrast, copolymer composition derived from MS data was not consistent with NMR results, obviously due to strong mass bias well known to occur during electrospray ionization of these polymeric species. Tandem mass spectrometry could reveal the random nature of the copolymer based on typical dissociation reactions, i.e., water elimination occurred from any two contiguous MAA units while MAA-MMA pairs gave rise to the loss of a methanol molecule. Polymer backbone cleavages were also observed to occur and gave low abundance fragment ions which allowed the structure of the initiating end-group to be confirmed.     

Polyacrylamide and poly(itaconic acid) complexes

Intermolecular complex formation through hydrogen bonding between poly(itaconic acid), partially neutralized and non-neutralized, and polyacrylamide was studied by potentiometry. The complexes were obtained by template polymerization of itaconic acid and partially neutralized itaconic acid on polyacrylamide as a template. All the complexes were characterized by elemental analysis, FTIR spectroscopy and thermal analysis.     

Molecular modeling of polymers. 10. Characterization of conformational transitions of poly(acrylic acid) and poly(methacrylic acid) using dyad structures

The conformational profiles of nearest side-chain neighbors, methylene-dyad structures, of poly(acrylic acid), PAA, and poly(methacrylic acid), PMA, were determined as a function of tacticity, extent of ionization, and presence of counterion. The dominant backbone conformer states are quite similar for both isotactic and syndiotactic diads in a common charge state. Thus, the overall dimensional properties of isotactic syndiotactic and atactic chains of PAA or PMA, based upon dyad interactions, are predicted to be alike for a given charge state. Significant deviations from precise t, g⁺, and g^? states are found for the dyad minimum energy conformations. The rod-to-coil and coil-to-rod transitions observed in PAA and PMA, respectively, as a function of increasing counterion concentration can be explained, to a large extent, by the conformational profiles of the corresponding dyad model structures. © 1994 John Wiley & Sons, Inc.     

Segmented block copolymers of poly(ethylene glycol) and poly(ethylene terephthalate)

A new series of segmented copolymers were synthesized from poly(ethylene terephthalate) (PET) oligomers and poly(ethylene glycol) (PEG) by a two‐step solution polymerization reaction. PET oligomers were obtained by glycolysis depolymerization. Structural features were defined by infrared and nuclear magnetic resonance (NMR) spectroscopy. The copolymer composition was calculated via ¹H NMR spectroscopy. The content of soft PEG segments was higher than that of hard PET segments. A single glass‐transition temperature was detected for all the synthesized segmented copolymers. This observation was found to be independent of the initial PET‐to‐PEG molar ratio. The molar masses of the copolymers were determined by gel permeation chromatography (GPC). © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4448–4457, 2004     

Stereoblock poly(lactic acid): synthesis via solid-state polycondensation of a stereocomplexed mixture of poly(L-lactic acid) and poly(D-lactic acid)

Stereoblock poly(lactic acid) consisting of D- and L-lactate stereosequences can be successfully synthesized by solid-state polycondensation of a 1:1 mixture of poly(L-lactic acid) and poly(D-lactic acid). In the first step, melt-polycondensation of L- and D-lactic acids is conducted to synthesize poly(L-lactic acid) and poly(D-lactic acid) with a medium-molecular-weight, respectively. In the next step, these poly(L-lactic acid) and poly(D-lactic acid) are melt-blended in 1:1 ratio to allow formation of their stereocomplex. In the last step, this melt-blend is subjected to solid-state polycondensation at temperature where the dehydrative condensation is allowed to promote chain extension in the amorphous phase with the stereocomplex crystals preserved. Finally, stereoblock poly(lactic acid) having high-molecular-weight is obtained. The stereoblock poly(lactic acid) synthesized by this way shows a higher melting temperature in consequence of the controlled block lengths and the resulting higher-molecular-weight. The product characterization as well as the optimization of the polymerization conditions is described. Changes in M(w) of stereoblock poly(lactic acid) (sb-PLA) as a function of the reaction time.     

Novel synthesis of biodegradable star poly(ethylene glycol)‐block‐poly(lactide) copolymers

Biodegradable star‐shaped poly(ethylene glycol)‐block‐poly(lactide) copolymers were synthesized by ring‐opening polymerization of lactide, using star poly(ethylene glycol) as an initiator and potassium hexamethyldisilazide as a catalyst. Polymerizations were carried out in toluene at room temperature. Two series of three‐ and four‐armed PEG‐PLA copolymers were synthesized and characterized by gel permeation chromatography (GPC) as well as ¹H and ¹³C NMR spectroscopy. The polymerization under the used conditions is very fast, yielding copolymers of controlled molecular weight and tailored molecular architecture. The chemical structure of the copolymers investigated by ¹H and ¹³C NMR indicates the formation of block copolymers. The monomodal profile of molecular weight distribution by GPC provided further evidence of controlled and defined star‐shaped copolymers as well as the absence of cyclic oligomeric species. The effects of copolymer composition and lactide stereochemistry on the physical properties were investigated by GPC and differential scanning calorimetry. For the same PLA chain length, the materials obtained in the case of linear copolymers are more viscous, whereas in the case of star copolymer, solid materials are obtained with reduction in their T_g and T_m temperatures. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3966–3974, 2007     

Synthesis and characterization of novel functional poly(vinyl alcohol-co-styrene sulfonic acid) copolymers

This paper first time reports the preparation of random anionic copolymers from vinyl acetate (VAc) bearing electro-donating substituent and sodium 4-vinylbenzenesulfonate (SSA) having electro-withdrawing substituent. Copolymers (PVA-co-SSA) of different composition have been successfully prepared by a simple free radical solution polymerization technique. Resulting final copolymer contained neutral hydrophilic as well as ionizable ion exchange sites. Evaluation of spectral data obtained from Fourier transform Infrared spectroscopy, Raman spectroscopy, and ¹H Nuclear magnetic resonance helped in identifying and confirming the chemical structure of copolymers. Characterization of copolymers by gel permeation chromatography revealed high molecular weight with moderate polydispersity index. Analysis of thermal stability and glass transition temperature of copolymers by thermogravimetric analysis and differential scanning calorimetry were found in between corresponding homopolymers. Physicochemical properties of PVA-co-SSA can be beneficial for prospective advanced application in the niche area of smart membrane technology for energy and environment.     

Electrochemical synthesis of soluble sulfonated poly(3-methyl thiophene)

Electrochemical polymerization of poly(3-methyl thiophene) films (3-MTy) which are self-doped with SO₃⁻ was investigated. The sulfonated poly(3-methyl thiophene) films synthesized from the solution which contained different amounts of HSO₃F. The sulfonated polymer films were found to be soluble in DMF and KOH. The solubility values increased and the conductivity values decreased with the increase in sulfonation ratio. The resulting polymers were characterized by cyclic voltammetry, UV-Vis, FT-IR, elemental analysis, dry conductivity measurements and SEM techniques.     

Synthesis and characters of hyperbranched poly(vinyl acetate) by RAFT polymeraztion

Reversible addition-fragmentation chain transfer (RAFT) polymerization of VAc in the presence of ECTVA, which capable of both reversible chain transferable through a xanthate moiety and propagation via a vinyl group, led to highly branched copolymers by a method analogous to self-condensing vinyl polymerization (SCVP). The ECTVA acted as a vinyl acetate AB^∗ inimer. It was copolymerized with vinyl acetate (VAc) in ratios selected to tune the distribution and length of branches of resulting hyperbranched poly(vinyl acetate). The degree of branching increased with chain ECTVA concentration, as confirmed by NMR spectroscopy. The polymer structure was characterized via MALDI–TOF. Retention of the xanthate compound during the polymerization was evidenced by successful chain extension of a branched (PVAc) macroCTA by RAFT polymerization. The branched PVAc led to better dissolution as compared to linear PVAc, an effect attributed primarily to an increased contribution of end groups.     

Microwave assisted hydroxyalkylamidation of poly(ethylene‐co‐acrylic acid) and formation of grafted poly(ϵ‐caprolactone) side chains

The microwave assisted amidation of poly(ethylene‐co‐acrylic acid) (PEAA) with 2‐(2‐aminoethoxy)ethanol was performed to yield a hydroxy functionalized poly(ethylene) based copolymer (PEAAOH) in a single step. PEAAOH was used as a polyinitiator for the ring‐opening polymerization of ε‐caprolactone. The obtained graft copolymers were studied via ¹H NMR spectroscopy, gel permeation chromatography, differential scanning calorimetry, polarized optical microscopy, and scanning electron microscopy. Microscopy methods show a crystallization behavior of banded spherulites. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3659–3667, 2007     

Binding of a surfactant counterion to low-charge-density poly(acrylic acid) and poly(methacrylic acid)

The binding of a cationic surfactant, dodecylpyridinium (C12Py) chloride, with a low-charge-density poly (methacrylic acid) (PMA) was investigated in buffer solutions under the condition of constant pH. The binding isotherms with PMA consisted of two and three steps at a pH lower and higher than 3.2, respectively. Bindings in the first step were independent of pH and this step was considered to correspond to the solubilization of the hydrocarbon chains of C12Py into the nonpolar region of the compact form of PMA. This is the indication of the compact form from the binding isotherm. At pH higher than 3.2, the second step was discriminated and it depended on the pH. In the third step, a sharp rise in the degree of binding (β) was observed accompanying the solubilization of the precipitates of the PMA–C12Py complex. The binding with poly(acrylic acid) (PAA) and PMA in conventional unbuffered NaCl solutions was also examined and the pH profile of the solution during the binding process was determined. In the case of unbuffered NaCl solutions, the binding with PAA took place cooperatively at the critical association concentration (cac). The binding isotherm consisted of two steps and the pH decreased with the increase in β. The binding isotherm of PMA, on the other hand, consisted of three steps: the pH decreased slightly in the first step and considerably in the second step with the increase in β but it increased with β in the third step, exhibiting a pH minimum around 3.2. The binding in the first step coincided with that obtained in the buffered solutions. Linear relationships between β and the pH were found for both polymers. In the case of PMA, no cac was observed in both buffered and unbuffered NaCl solutions. Received: 24 January 2001 Accepted: 23 May 2001     

Synthesis of poly(vinyl laurate)‐b‐poly(vinyl stearate) diblock copolymers by cobalt‐mediated radical polymerization in solution

Poly(vinyl laurate) (PVL) and poly(vinyl stearate) (PVS) were synthesized by means of cobalt‐mediated radical polymerization (CMRP). Cobalt(II) diacetylacetonate (Co(acac)₂) was demonstrated to control the radical polymerization of these monomers in solution. Molecular weights up to 15,000 g·mol^?1 were obtained with reasonably low polydispersity indices (PDI < 1.3). The efficiency of the redox initiator [lauroyle peroxide (LPO)/citric acid (CA)] was found to be low (around 10%) as already reported for vinyl acetate. The solvent and temperature were found to have a very weak influence on the initiator efficiency. It appeared that CA played no role in the initiation process that only involved a redox reaction between LPO and Co(acac)₂. PVL‐b‐PVS diblock copolymers could be synthesized using two strategies: (1) Sequential addition, that is, addition of the second monomer (VS) at high conversion of the first one (VL). (2) Macroinitiator technique, that is, isolation of a PVL macroinitiator then polymerization of VS from this cobalt functionalized macroinitiator. Both techniques allowed the synthesis of diblock copolymers with molar masses around 25,000 g·mol^?1 and PDI lower than 1.4. The resulting materials were characterized by DSC, revealing that both blocks exhibit side‐chain crystallinity and phase segregate in the bulk. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Thermogravimetric analysis of poly(alkyl methacrylates) and poly(methylmethacrylate-g-dimethyl siloxane) graft copolymers

The thermal stabilities of various poly(alkyl methacrylate) homopolymers and poly(methyl methacrylate-g-dimethyl siloxane) (PMMA-g-PSX) graft copolymers have been determined by thermogravimetric analysis (TGA). As expected, the thermal stabilities of poly(alkyl methacrylates) were a function of the ester alkyl group, and polymerization mechanism. In particular, thermally labile linkages, which result from termination during free radical or nonliving polymerization mechanisms, decrease the ultimate thermal stabilities of the polymers. However, graft copolymers, which were prepared by the macromonomer technique with free radical initiators, exhibited enhanced thermal stability compared to homopolymer controls. A more complex free radical polymerization mechanism for the macromonomer modified polymerization may account for this result. © 1994 John Wiley & Sons, Inc.