Stress wave attenuation in composites during ballistic impact

Experimental studies are presented on stress wave attenuation during ballistic impact for four types of polymer matrix composites. The materials considered are plain weave E-glass/epoxy, 8H satin weave T300 carbon/epoxy and two types of hybrid composite made using plain weave E-glass fabric and 8H satin weave T300 carbon fabric with epoxy resin. Strain profiles were obtained during ballistic impact event at certain distances from the point of impact. There is stress wave attenuation leading to reduction in peak strains obtained as the stress wave propagates away from the point of impact. Further, it is observed that ballistic limit velocity, V₅₀, can be increased compared to carbon only composites by adding E-glass layers to T300 carbon layers.     

Epoxy resin particles. I. Spontaneous particle formation by the polymerization reaction of epoxy resin in a stationary system using polyethers as organic media

 A thermosetting epoxy resin was found to form polymer particles spontaneously in a stationary reaction system using polyethers as solvents. Poly(oxypropylene) and its copolymer with poly(oxyethylene) were effectively used as reaction media. The diameter of the resultant particles depended on the structure of the amines used as hardeners as well as on the molecular weight and composition of the polyether media. The glass-transition temperatures of the particles revealed that a small amount of polyether used as the medium was incorporated in the epoxy resin particles during the polymerization. Received: 8 September 1999 Accepted: 7 December 1999     

Combined effect of zeolite and boric acid on thermal behavior of epoxy composites

The particles of natural zeolite in combination with boric acid were incorporated into the epoxy resin ED-20 in order to improve the thermal stability of epoxy polymer. Epoxy resin was cured using polyethylenepolyamine. Characterization of the epoxy composites was carried out by using Fourier transform infrared spectrometry, thermogravimetric analysis (TG) and differential scanning calorimetry (DSC) under flow of air and argon. The thermal behavior of the zeolite/boric acid-based epoxy composites (total percentage 15 mass%) were compared with that of 15 mass% boric acid-based epoxy system and the neat epoxy resin. TG and DSC results revealed that the combination of 5 mass% zeolite and 10 mass% boric acid significantly increased the mid-point temperature and residue, and decreased the maximum decomposition rate of the epoxy composites at the heating.     

Benzoxazine modified diglycidyl ether of bisphenol-a/silicon/siliconized epoxy hybrid polymer matrices: Mechanical,thermal, electrical and morphological properties

Benzoxazines modified epoxy hybrid polymer matrices were developed using benzoxazines (CB_DDM and BMPB_DDM) and epoxy resins (DGEBA, SE and EP-HTPDMS) to make them suitable for high performance applications. The benzoxazine-epoxy hybrid polymer matrices were prepared via in-situ polymerization and were investigated for their thermal, thermo-mechanical, mechanical, electrical and morphological properties. Two types of skeletal modified benzoxazines namely 1,1-bis(3-methyl-4-hydroxyphenyl)cyclohexane benzoxazine (CB_DDM) and bis(4-maleimidophenyl) benzoxazine (BMPB_DDM) were synthesized by reacting paraformaldehyde and 4,4′-diaminodiphenylmethane with 1,1-bis (3-methyl-4-hydroxyphenyl)cyclohexane and N-(4-hydroxyphenyl)maleimide respectively. Epoxy resins viz., diglycidyl ether of bisphenol-A (DGEBA), silicon incorporated epoxy (SE) and siliconized epoxy resin (EP-HTPDMS) were modified with 5, 10 and 15 wt% of benzoxazines using 4,4′-diaminodiphenylmethane as a curing agent at appropriate conditions. The chemical reaction of benzoxazines with the epoxy resin was carried out thermally and the resulting product was analyzed by FT-IR spectra. The glass transition temperature, curing behavior, thermal stability, char yield and flame resistance of the hybrid polymers were analysed by means of DSC, TGA and DMA. Mechanical properties were studied as per ASTM standards. The benzoxazines modified epoxy resin systems exhibited lower values of dielectric constant and dielectric loss with an enhanced values of of arc resistance, glass transition temperatures, degradation temperatures, thermal stability, char yield, storage modulus, tensile strength, flexural strength and impact strength.     

Effect of UV radiation on some polymeric networks based on vinyl ester resin and modified lignin

Some semi-interpenetrating polymer networks (semi-IPNs) based on vinyl ester resin (VER) and ammonium lignosulfonate (ALS) modified lignin were synthesized and characterized using Fourier transform-infrared (FT-IR) spectroscopy, optical microscopy (OM) and differential scanning calorimetry (DSC) techniques. VER was synthesized starting from an epoxy resin in reaction with acrylic acid. The cross-linking reaction was initiated by UV radiation. The synthesized networks showed good compatibility, due to some possible interactions between the functional groups from VER and ALS components (OH, especially). A slight effect of photostabilization of the VER was noticed, due to the ALS structures which were incorporated into the resin matrix.     

The application of highly soluble amine-terminated aromatic polyimides with pendent tert-butyl groups as a tougher for epoxy resin

Polyimides(PIs) with various molecular weights synthesized via the reaction of aromatic diamine monomer containing tert-butyl groups with aromatic dianhydride were highly soluble in common organic solvents and some epoxy resins at room temperature. These PIs can be incorporated in the absence of organic solvent into epoxy resin E51 with the loading below 2 wt% forming EP-PI composites. No phase separation is observed by SEM on cryogenically fractured surfaces of EP-PI composites. The PI can improve mechanical properties, especially impact strength. Adding 2 wt% PI-1.5W, the impact strength reaches to 55 k J/m2 with the increase in tensile and flexural strengths by 14% and 3%, respectively. SEM analyses for the fracture surface suggest that PI reduces the crosslink density, improves the plasticity of epoxy resin and changes the mode of fracture from fragile to ductile. Moreover, the glass transition temperature of EP-PI composites was found to increase to a significant extent.     

Synthesis and Characterization of Fluorinated Acrylic Polymer and the Properties of Epoxy Thermosets Modified With It

A novel fluorinated acrylic polymer poly(2,2,3,4,4,4-hexafluorobutyl methacrylate)-r-poly(glycidyl methacrylate) (PHFMA-r-PGMA) was synthesized and used to modify the general performances of epoxy resin. Fourier transform infrared spectroscopy (FTIR) and ¹H nuclear magnetic resonance spectroscopy (¹H-NMR) successfully verified the synthesis of PHFMA-r-PGMA. In order to study the effect of epoxy groups in PHFMA-r-PGMA on the properties of modified epoxy resin, corresponding fluoropolymer without epoxy group (PHFMA) was also prepared, and the properties of epoxy thermosets modified by two kinds of fluoropolymers were comparatively studied. The contact angle measurements indicated that the PHFMA-r-PGMA and PHFMA modified thermosets both showed considerable hydrophobicity and lipophobicity. For further comparison, it was also found that the thermosets modified by PHFMA-r-PGMA had a little worse hydrophobicity and lipophobicity but better surface stability than which modified by PHFMA because the epoxy groups in PHFMA-r-PGMA “locked” more fluoropolymers in the bulk matrix of the thermosets, but PHFMA was more freely able to migrate to the surface of the thermosets. SEM images of the fracture surface of PHFMA-r-PGMA and PHFMA modified epoxy thermosets displayed “irregular ripples” or “protuberant island” structures, which suggesting both of these two copolymers could significantly toughen epoxy resin. The results of differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) showed that the thermosets modified by PHFMA-r-PGMA had better thermal stability than which modified by PHFMA due to the higher crosslinking density between PHFMA-r-PGMA and epoxy resin because of the epoxy groups in PHFMA-r-PGMA. The mechanical properties were investigated by tensile testing and impact testing. Although the tensile strength of the PHFMA-r-PGMA and PHFMA modified epoxy thermosets both declined slightly with growing the content of fluoropolymers, the elongation at break and impact strength both increased first and then decreased in the meantime, which indicated that the two kinds of modified thermosets had better toughness than pure epoxy resin. It may be because the macro-phase separation between the long fluorine carbon chain segments and epoxy resin during curing could absorb the impact energy effectively.     

Phase separation,porous structure,and cure kinetics in aliphatic epoxy resin containing hyperbranched polyester

Thermosetting blends of an aliphatic epoxy resin and a hydroxyl‐functionalized hyperbranched polymer (HBP), aliphatic hyperbranched polyester Boltorn H40, were prepared using 4,4′‐diaminodiphenylmethane (DDM) as the curing agent. The phase behavior and morphology of the DDM‐cured epoxy/HBP blends with HBP content up to 40 wt % were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM). The cured epoxy/HBP blends are immiscible and exhibit two separate glass transitions, as revealed by DMA. The SEM observation showed that there exist two phases in the cured blends, which is an epoxy‐rich phase and an HBP‐rich phase, which is responsible for the two separate glass transitions. The phase morphology was observed to be dependent on the blend composition. For the blends with HBP content up to 10 wt %, discrete HBP domains are dispersed in the continuous cured epoxy matrix, whereas the cured blend with 40 wt % HBP exhibits a combined morphology of connected globules and bicontinuous phase structure. Porous epoxy thermosets with continuous open structures on the order of 100–300 nm were formed after the HBP‐rich phase was extracted with solvent from the cured blend with 40 wt % HBP. The DSC study showed that the curing rate is not obviously affected in the epoxy/HBP blends with HBP content up to 40 wt %. The activation energy values obtained are not remarkably changed in the blends; the addition of HBP to epoxy resin thus does not change the mechanism of cure reaction of epoxy resin with DDM. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 889–899, 2006     

Preparation and characterization of pavement materials with phase-change temperature modulation

A kind of pavement crack repairing material with temperature regulation property was successfully prepared through one-step method, in which the paraffin was incorporated into the polyurethane/epoxy resin-interpenetrating polymer networks. Differential scanning calorimeter results indicated that the phase-change latent heat of sample A was 14.4 kJ kg^?1, and the phase transition temperature was ??0.3 °C. FTIR and thermogravimetry measurements verified that the paraffin was successfully incorporated into the interpenetrating polymer network without leakage and reacted with the carrier, which exhibited high thermal stability above 300 °C. After 1 year of road test, there was no breakage for the repairing pavement with paraffin–polyurethane/epoxy resin-interpenetrating polymer networks, and there was almost no change for the accumulated attenuation of phase-change latent heat. Therefore, the materials of paraffin–polyurethane/epoxy resin-interpenetrating polymer networks have good chemical stability and thermal stability.

     

Effect of homologous nano-composites on the thermal degradation of the silicone resin

Effect of homologous of nano-composites on the thermal degradation of the silicone resin was researched based on graphene oxide (GO)/polyhedral oligomeric silsesquioxane (POSS). First, the amino-POSS was grafted onto the GO surface (GO/POSS) via the amide bond. Second, GO/POSS was incorporated into the silicone with active epoxy group via chemistry grafting. The reaction kinetics of the thermal decomposition of the epoxy–silicone resin based on nano-composite homologous effect is developed. The initial decomposition temperature of the modified silicone resin is improved by 77.2°C. At high temperatures, GO/POSS-modified silicone molecular end forms homologous nano-structures, which can restrain silicone future degradation. The developed strategy has potential to restrain the degradation of the polymer molecular chain.     

Synthesis and characterization of a novel cycloaliphatic epoxy resin starting from dicyclopentadiene

A novel tri-functional cycloaliphatic epoxy resin was synthesized starting from dicyclopentadiene. The chemical structures of the resultant epoxy resin and its precursor were characterized with FTIR spectroscopy, EEW, ¹H NMR and Mass spectrographic analyses. The thermal and mechanical properties of the resulting polymer were evaluated with differential scanning calorimeter (DSC), thermo-gravimetric and thermal mechanical analysis. Compared to that of the common cycloaliphatic epoxy resin ERL-4221, the cured polymer of the novel epoxy resin exhibited lower thermal degradation temperature with much higher char yield and similar thermal expansion coefficient. These excellent overall performances make it a promising packaging material.     

新环氧树脂纳米复合材料的合成和结构研究

以具有层状硅酸盐结构的累托石(REC)为主体,以烷基季铵盐为改性剂合成了有机累托石(OREC),以有机累托石和环氧树脂复合,制备出纳米复合材料。累托石含量在0.8wt.% 时,纳米复合材料具有最佳力学和热学性能,冲击强度增加到65.6 kJm-2,断裂伸长率从4.7 %增加到20.2 %,玻璃化转变温度提高到 197.9 ℃。用X-小角衍射法、透射电镜和红外吸收光谱研究了材料的微观结构,XRD 衍射图显示,未经处理REC 的层间距d001 = 2. 2 nm,经有机改性后,累托石片层间距扩大到2.8 nm,与环氧树脂复合后,其层间距扩大到4.2 nm 左右,FT-IR图显示,有机累托石中出现十六胺的特征吸收峰,TEM照片显示该复合材料是一种纳米复合材料。     

Epoxy-modified, unsaturated polyester hybrid networks

Hybrid polymer networks (HPNs) based on unsaturated polyester resin (UPR) and epoxy resins were synthesized by reactive blending. The epoxy resins used were epoxidised phenolic novolac (EPN), epoxidised cresol novolac (ECN) and diglycidyl ether of bisphenol A (DGEBA). Epoxy novolacs were prepared by glycidylation of the novolacs using epichlorohydrin. The physical, mechanical, and thermal properties of the cured blends were compared with those of the control resin. Epoxy resins show good miscibility and compatibility with the UPR resin on blending and the co-cured resin showed substantial improvement in the toughness and impact resistance. Considerable enhancement of tensile strength and toughness are noticed at very low loading of EPN. Thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC) were employed to study the thermal properties of the toughened resin. The EPN/UPR blends showed substantial improvement in thermal stability as evident from TGA and damping data. The fracture behaviour was corroborated by scanning electron microscopy (SEM). The performance of EPN is found to be superior to other epoxy resins.     

Fabrication of CdS Nanorods in PVP Fiber Matrices by Electrospinning

Summary: A controlled fabrication of rod‐like nanostructures of cadmium sulfide (CdS) incorporated into polymer fiber matrices has been developed by an electrospinning method. Here, poly(vinyl pyrrolidone) (PVP) was used as a polymer capping reagent, utilizing the interactions of cadmium ions with the carbonyl groups in the PVP molecules. The formation of CdS nanorods inside the PVP was carried out via the reaction of Cd²⁺ with H₂S. SEM images showed that the electrospun films of PVP/CdS are composed of fibers with a diameter between 100 and 900 nm. TEM proved that most of the CdS nanorods are incorporated in the PVP fibrous film. The diameter of the rod is about 50 nm and the length is from 100 to 300 nm.

TEM image of the CdS nanorods formed in the PVP fibrous film.     

Study on liquid oxygen compatibility of bromine‐containing epoxy resins for the application in liquid oxygen tank

The liquid oxygen compatible epoxy resin was obtained by the polycondensation between tetrabromobisphenol A and neat epoxy resins. The results of liquid oxygen impact test indicated that the synthetic epoxy resins were compatible with liquid oxygen. The relationship between impact reaction sensitivity (IRS) and flame retardancy were studied by liquid oxygen impact test and limiting oxygen index test. The results showed that the flame‐retardant modification of epoxy resin was valuable to reduce the IRS. The thermal gravimetric analysis results indicated that the Br · radical was quickly released in relatively low temperature (approximately 370°C) for compatible epoxy resin. The Br · radical was a key factor to promote the epoxy resin compatible with the liquid oxygen. The X‐ray photoelectron spectroscopy was used to survey the distribution of functional groups on the surface of samples before and after impact. The results showed that the oxidation reaction and carbonization process may occur on the surface of samples after impact. The liquid oxygen compatibility mechanism is proposed in this paper. The bromine‐containing epoxy resin has the potential to be the material used in liquid oxygen tank. Copyright © 2015 John Wiley & Sons, Ltd.     

Nanoscale highly filled epoxy nanocomposite

A new technique has been developed to prepare a highly filled epoxy-montmorillonite (MMT) nanocomposite using an organically modified MMT. Composites with clay content up to 70 wt.% exhibit unusual transparency, which is related to the spatial distribution of the mineral nanodomains. Dispersion of the layered silicate within the crosslinked epoxy matrix was verified using X-ray diffraction pattern, revealing layer spacings of 30 and 70 Å. Examination of these materials by scanning electron microscopy and transmission electron microscopy showed that intercalates have wholly layered morphology at all scales, oriented parallel to the surface of the specimen and have good wetting to the silicate surface by the epoxy matrix. Silicate lamellae intercalated with epoxy resin assembled into a cluster of about 50-120 nm thickness. These clusters assembled into superclusters with an average thickness of 300 nm. Studies by the Vickers hardness test of an epoxy-MMT nanocomposite containing 60 wt.% MMT indicated that the diamond pyramid hardness was 10-29 kg/mm².     

一种液晶环氧增韧环氧树脂的研究

环氧树脂具有优异的机械性能 ,耐高温以及良好的加工工艺性 .被广泛用于机械、航天、船舶等领域 .由于环氧树脂固化后断裂延伸率小 ,脆性大 ,使其应用受到了一定的限制 .为此 ,国内外学者对环氧树脂进行了大量的改性研究工作 .用含有“柔性链段”的固化剂固化环氧 ,在交联网络中引入柔性链段[1] ;在环氧基体中加入橡胶弹性体[2 ] 、热塑性树脂[3 ,4] 、液晶聚合物[5,6] 等分散相或用热固性树脂连续贯穿于环氧树脂网络中形成互穿、半互穿网络结构[7] ,以改善环氧树脂的韧性 .本文采用液晶环氧化合物原位复合增韧环氧树脂 ,考察了液晶环氧对环…     

Chemical force spectroscopy in heterogeneous systems: intermolecular interactions involving epoxy polymer,mixed monolayers,and polar solvents

We used chemical force microscopy (CFM) to study adhesive forces between surfaces of epoxy resin and self-assembled monolayers (SAMs) capable of hydrogen bonding to different extents. The influence of the liquid medium in which the experiments were carried out was also examined systematically. The molecular character of the tip, polymer, and liquid all influenced the adhesion. Complementary macroscopic contact angle measurements were used to assist in the quantitative interpretation of the CFM data. A direct correlation between surface free energy and adhesion forces was observed in mixed alcohol-water solvents. An increase in surface energy from 2 to 50 mJ/m(2) resulted in an increase in adhesion from 4-8 nN to 150-300 nN for tips with radii of 50-150 nm. The interfacial surface energy for identical nonpolar surface groups of SAMs was found not to exceed 2 mJ/m(2). An analysis of adhesion data suggests that the solvent was fully excluded from the zone of contact between functional groups on the tip and sample. With a nonpolar SAM, the force of adhesion increased monotonically in mixed solvents of higher water content; whereas, with a polar SAM (one having a hydrogen bonding component), higher water content led to decreased adhesion. The intermolecular force components theory was used for the interpretation of adhesion force measurements in polar solvents. Competition between hydrogen bonding within the solvent and hydrogen bonding of surface groups and the solvent was shown to provide the main contribution to adhesion forces. We demonstrate how the trends in the magnitude of the adhesion forces for chemically heterogeneous systems (solvents and surfaces) measured with CFM can be quantitatively rationalized using the surface tension components approach. For epoxy polymer, inelastic deformations also contributed heavily to measured adhesion forces.     

整体式吸附萃取搅拌棒在检测环境水样中镉离子含量方面的应用

通过逐步聚合反应制备了一种新型整体式吸附萃取搅拌棒,将其应用于环境水中镉离子的吸附萃取.考察了介质酸度、搅拌速率、吸咐时间、解吸溶剂和时间等实验条件对吸附量的影响.控制溶液pH为6.0,搅拌棒转速为300 r/min,吸附30 min,5% HNO3作为解吸液解吸10 min,采用等离子体原子发射光谱仪对Cd离子进行检...     

Cure behavior and thermal stability of an epoxy: new bismaleimide blends for composite matrices

A new bismaleimide (BMI) resin was synthesized to formulate epoxy(tetraglycidyl diaminodiphenyl methane; TGDDM) – bismaleimide thermoset blends for composite matrix applications. 4,4′-diaminodiphenyl methane (DDM) was used as an amine curing agent for the TGDDM. A Fourier transform infrared (FTIR) spectroscopy was employed to characterize the new BMI resin. Cure behavior of the epoxy–BMI blends was studied using a differential scanning calorimeter (DSC). DSC thermograms of the thermoset blends indicated two exothermic peaks. The glass transition temperature of the thermoset blends decreased with BMI content. Thermogravimetric analysis (TGA) was carried out to investigate thermal degradation behavior of the cured epoxy–BMI thermoset blends. The new BMI resin reacted partially with the DDM and weak intercrosslinking polymer networks were formed during cure of the thermoset blends.