竹基多孔碳材料的制备及其协同阻燃环氧树脂研究

以KOH为致孔剂,制备了竹基微孔多孔碳材料(PCM);将PCM与聚磷酸铵(APP)添加于环氧树脂(EP),研究了PCM协同APP阻燃EP复合材料的作用及机理.BET吸附、扫描电子显微镜(SEM)及X射线光电子能谱(XPS)分析显示,PCM6的比表面积、孔容、孔径分别为2063 m2/g、0.9 cm2/g、1.8 nm;粒径为1~5μm;表面存在C—C,C—O—,C O及COO—等活性基团.极限氧指数(LOI)、UL 94垂直燃烧及锥形量热仪(Cone)研究表明,0.8 wt%的PCM6与3.1 wt%的APP复合可使EP复合材料的LOI由24.6%提高到27.3%,热释放速率峰值降低45.4%,PCM6表现出良好的协同阻燃作用.热失重分析及XPS研究表明,PCM6提高了阻燃EP复合材料的热稳定性,催化APP释放NH3、H2O,加快了交联成炭的速度及热解产物焦磷酸(酯)的形成,由此揭示了PCM协同APP阻燃EP的作用机理.     

阻燃超疏水棉纤维的制备及性能

将氢氧化镁(Mg(OH)₂)凝胶沉积到棉纤维上,以提高棉纤维表面粗糙度和阻燃性能,随后将含有Mg(OH)₂的棉纤维浸渍到聚二甲基硅氧烷(PDMS)溶液,获得阻燃超疏水棉织物。 并对棉纤维进行了傅里叶变换红外光谱仪(FTIR)、扫描电子显微镜(SEM)、疏水性、热稳定性、阻燃性能和耐久性测试。 结果表明,Mg(OH)₂负载到织物上,使得织物表面具有一定的微/纳米结构,形成了粗糙涂层。 当Mg(OH)₂浓度为1.0 mol/L时,Mg(OH)₂/PDMS改性的织物接触角(CA)可达158°,极限氧指数(LOI)提升至24.5%,导热系数为0.0525 W/(m·K), 具有超疏水和阻燃性能。 整理后织物经过20次洗涤,100次磨擦,极端条件处理后,CA仍大于150°,LOI值高于23%,显示了较好的耐久性。     

Ni2P/Cu(OH)2催化剂的制备及其全解水性能研究

通过化学处理法在泡沫铜基底表面生成Cu(OH)₂纳米线,大大增加了基底材料的表面积和导电性.采用水热法在Cu(OH)₂纳米线表面制备片状Ni-CH/Cu(OH)₂前驱体,对Ni-CH/Cu(OH)₂前驱体进行低温磷化得到多级结构Ni₂P/Cu(OH)₂催化剂.通过扫描电子显微镜(SEM)、X射线光电子能谱仪(XPS)和X射线衍射仪(XRD)对催化剂的物质结构和表面形貌进行了表征.采用线性伏安法、恒电位等技术对催化剂的电化学性能进行测试.在1.0 mol·L^-1 KOH碱性溶液中,当电流密度为10 mA·cm^-2时,Ni₂P/Cu(OH)₂的析氢反应(HER)和析氧反应(OER)过电位分别为133和333 mV,且均具有较好的稳定性.将这种多级结构Ni₂P/Cu(OH)₂催化剂分别用作阳极和阴极进行全解水电解,电流密度达到10 ...     

亚微米级多刺状星形氧化铜的制备

在阳离子gemini表面活性剂[C₁₆H₃₃(CH₃)₂N^＋(CH₂)₄N^＋(CH₃)₂C₁₆H₃₃]•2Br^－ (16-4-16)存在条件下, 以六次甲基四胺为沉淀剂, 利用水热合成法制备了大量多刺状星形亚微米级氧化铜. 用X射线衍射(XRD), X射线光电子能谱(XPS), 扫描电子显微镜(SEM)和透射电子显微镜(TEM)等多种手段对制备产物的表征结果表明, 所得产物是具有单斜结构多刺状星形氧化铜. 考察了表面活性剂浓度、温度以及铜源对产物物相及其形貌的影响.     

两个多钒盖帽的Keggin型多铌钒酸盐衍生物的水热合成与表征

通过水热方法合成了2个由多铌酸盐和过渡金属配合物形成的有机-无机杂化配合物[Cu(TETA)]₄[VNb₁₂(VO)₄O₄₀][OH]·10H₂O(1)和[Cu(TETA)]₄[VNb₁₂(VO)₆O₄₀][OH]₅·5H₂O(2)(TETA=三亚乙基四胺). 化合物1和2的多阴离子分别是由4个{VO₅}帽和6个{VO₅}帽加盖在Keggin型多铌酸盐的方形缺口上形成的, 它们通过多酸阴离子中Nb-O_t (O_t =端氧)与[Cu(TETA)]²⁺配合物的金属中心配位构筑形成三维结构. 价键计算结果表明, Keggin中心的钒为+5价, 帽位的钒为+4价, X射线光电子能谱分析(XPS)结果也证实了这一结论. 通过单晶X射线衍射分析、红外光谱(IR)、粉末X射线衍射(PXRD)、热重(TG)分析和元素分析对这2个化合物的结构和性质进行了表征.     

Zn-MOF模板法制备ZnO/C/SNTs及其药物缓释性能

采用超声法一步合成了SiO₂包覆金属-有机骨架[Zn₆(OH)₃(BTC)₃(H₂O)₃] ·7H₂O(Zn-MOF, BTC=1,3,5-均苯三羧酸根)纳米晶, 在N₂保护下, 热解Zn-MOF@SiO₂获得了ZnO/C/SNTs复合物, 进而与布洛芬(HIBU)反应合成药物组装体Zn(IBU)₂/C/SNTs. 通过透射电子显微镜(TEM)、 傅里叶变换红外光谱仪(FTIR)、 高分辨透射电子显微镜(HRTEM)和X射线衍射仪(XRD)对样品的结构和形貌进行表征. 结果显示, Zn-MOF@SiO₂呈棒状, 具有清晰的核/壳结构, 形貌单一, 分散性良好. 煅烧后SNTs结构稳定, 形貌基本不变. 载药实验表明, 药物组装体的载药量为752 mg/g, 并具有良好的pH响应性能.     

水性聚氨酯阻燃纳米复合材料的Click反应制备及性能

以4,4'-二羟甲基-1,4-庚二炔功能单体作为扩链剂制备了端炔基功能化聚氨酯, 与叠氮基改性纳米蒙脱土(MMT-N₃)、 纳米氢氧化铝(ATH-N₃)和纳米氢氧化镁(MH-N₃)通过Click反应制备了水性聚氨酯(WPU)阻燃纳米复合材料. 采用红外光谱(FTIR)、 核磁氢谱(¹H NMR)和扫描电子显微镜(SEM)对WPU阻燃纳米复合材料的结构进行了表征, 对比研究了纳米阻燃剂配比和制备方法对WPU阻燃纳米复合材料的氧指数、 动态燃烧行为和热稳定性的影响. 阻燃性能研究结果表明, 当MMT-N₃, MH-N₃和ATH-N₃的质量分数分别为7%, 2%和1%时, 采用Click反应制备的复合材料的氧指数比纯WPU高7%, 点燃时间从10 s延长到29 s, 峰值热释放速率和烟释放速率分别降低了41%和42%. 热失重分析结果表明, 当MMT-N₃质量分数为10%时, 与WPU相比, 采用Click反应制备的MMT/WPU复合材料在热失重50%时的温度提高了21 ℃. 复合材料断面和燃烧后残渣的SEM分析证明在聚合物基体中Click反应是分散纳米材料的一种有效方法.     

石墨烯负载离子液体的制备及其与六苯氧基环三磷腈协效阻燃环氧树脂的性能研究

本文以可膨胀石墨(EG)和1-丁基-3-甲基咪唑六氟磷酸盐离子液体([BMIM]PF_6)为原料,在去离子水中通过绿色、简单的球磨法成功制备出了石墨烯负载离子液体杂化物(GnP@ILs),并对其结构组成进行表征.将GnP@ILs单独或与六苯氧基环三磷腈(HPCTP)混合加入到环氧树脂(EP)中,研究其对EP复合材料综合性能的影响.极限氧指数(LOI)、垂直燃烧(UL-94)和锥形量热测试结果表明,GnP@ILs能提高EP复合材料的阻燃性能,同时与HPCTP复配的EP复合材料(EP/7.2wt%HPCTP/1.8wt%GnP@ILs)的阻燃性能最好,LOI达到33.8%,并通过了UL-94V 0级.EP/7.2wt%HPCTP/1.8wt%GnP@ILs的热释放速率峰值和总热释放量分别降低了55.54%和44.28%.同时,[BMIM]PF_6的加入增强了阻燃剂与EP的界面相容性,EP复合材料的拉伸强度和抗冲强度均明显提高.     

多孔MOFs(UiO-66和UiO-68)合成与表征的综合性大学化学实验*

结合科研工作设计了一个综合性大学化学实验--多孔MOFs(UiO-66,[Zr₆O₄(OH)₄(BDC)₄]_n (H₂BDC=对苯二甲酸)和UiO-68,[Zr₆O₄(OH)₄(ATDA)₄]_n (H₂ATDA=2′-氨基-[1,1′:4′,1″-三联苯]-4,4″-二羧酸))的合成、表征及相关性能研究。该设计实验选择具有不同长度的配体与锆离子组装得到晶态材料,整个实验过程包括有机合成、溶剂热合成、X射线单晶衍射和粉末衍射、红外光谱、热重分析等内容,综合了各大化学知识点于一身。经过此实验,学生不仅能有效了解并掌握MOFs材料的合成、性能测试与相关仪器的操作,还可做到理论结合实际、基础知识结合现代科研手段,培养学生的化学科研素养。     

纳米晶(CeO2)1-x(BiO1.5)x固溶体的水热合成与离子输运性质研究

在240℃水热体系中首次合成出系列纳米晶固溶体(CeO₂)_1-x(BiO_1.5)_x(x=0.0～0.50).产物采用X射线衍射,扫描电子显微镜和X射线光电子能谱仪进行表征.Bi₂O₃在CeO₂中的固溶限约为50%.所有固溶体结晶属立方萤石结构,粒度范围为10～18nm.当Bi₂O₃掺杂量小于固溶限时,于800℃烧结不会导致结构转变.而对于(CeO₂)_0.5(BiO_1.5)_0.5,于800℃在空气中烧结将导致固溶限降低.Bi₂O₃含量低于固溶限时,固溶体只具有体电导,而(CeO₂)_0.6(BiO_1.5)_0.4的总电导可分为体电导和晶界电导.体电导为氧离子,而晶界为来自电极的银离子.     

Luminescence properties of CdTe QDs embedded in Zn5(CO3)2(OH)6 matrix

CdTe@Zn₅(CO₃)₂(OH)₆ composites were synthesized by a hydrothermal method. CdTe@Zn₅(CO₃)₂(OH)₆ composite nanospheres were characterized via X-ray diffraction, scanning electron microscopy, energydispersive X-ray spectroscopy, and photoluminescence (PL). The hydrothermal reaction time and the mole ratios of Zn/Te played important roles in the growth and fluorescence intensity of CdTe@Zn₅(CO₃)₂(OH)₆ composites. The composite powders showed peak PL at 578 nm at 1.6 times the intensity of powdered CdTe QDs. CdTe@Zn₅(CO₃)₂(OH)₆ exhibited a strong yellow fluorescence emission, and its preparation method was easy and economical. Therefore, CdTe@Zn₅(CO₃)₂(OH)₆ offers potential applications in biological markers and light-emitting diodes.     

Preparation of Poly(phosphoric acid piperazine) and Its Application as an Effective Flame Retardant for Epoxy Resin

A phosphorus-nitrogen containing flame retardant additive of poly(phosphoric acid piperazine),defined as PPAP,was synthesized by the salt-forming reaction between anhydrous piperazine and phosphoric acid,and the dehydration polymerization under heating in nitrogen atmosphere.Its chemical structure was well characterized by Fourier transform infrared (FTIR) spectroscopy,13C and 31p solid-state nuclear magnetic resonance measurements.The synthesized PPAP and curing agent m-phenylenediamine were blended into epoxy resin (EP) to prepare flame retardant EP thermosets.The effects of PPAP on the fire retardancy and thermal degradation behavior of cured EP/PPAP composites were investigated by limiting oxygen index (LOI),vertical burning (UL-94),thermogravimetric analysis/infrared spectrometry (TG-IR) and cone calorimeter tests.The morphologies and chemical compositions of char residues for cured epoxy resin were investigated by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS),respectively.The results demonstrated that the flame retardant EP thermosets successfully passed UL-94 V-0 flammability rating and the LOI value was as high as 30.8％ when incorporating 5wt％ PPAP into the EP thermosets.The TGA results indicated that the synthesized PPAP flame retardant additive possessed high thermal stability and excellent charring capability.Meanwhile,the incorporation of PPAP stimulated the epoxy resin matrix to decompose and charring ahead of time due to its catalytic decomposition effect,which led to a higher char yield at high temperature.The morphological structures and the analysis results of XPS for char residues of EP thermosets revealed that the introduction of PPAP benefited the formation of a sufficient,more compact and homogeneous char layer containing phosphorus-nitrogen flame retardant elements on the material surface during combustion.The formed char layer with high quality effectively prevented the heat transmission and diffusion,limited the production of combustible gases,and inhibited the emission of smoke,leading to the reduction of heat and smoke release.     

Effect of different ionic layered compounds decorated with zinc hydroxystannate on flame retardancy and smoke performance of epoxy resin

ZHS@ Mg‐Al‐LDH and ZHS@α‐ZrP hybrid materials were prepared by electrostatically loading zinc hydroxystannate (ZHS) on the layered compounds (Mg‐Al‐LDH and α‐ZrP) in this work. With the addition of 2 wt% of the two hybrid materials to epoxy resin (EP), respectively, the fire hazard of EP and its composites were investigated. The limiting oxygen index (LOI) of ZHS@ Mg‐Al‐LDH/EP composite increased by 19.0% compared with pure EP, while its peak heat release rate (PHRR), total heat release rate (THR), and peak smoke release rate (SPR) decreased by 48.2%, 20.8%, and 21.6%, respectively, evidenced by the results of the LOI test and cone calorimetry test (CCT). The LOI of ZHS@α‐ZrP/EP composite increased by 20.4%, and its PHRR, THR, and SPR decreased by 47.7%, 21.4%, and 27.1%, respectively. Both hybrid materials showed prominent flame retardant and smoke suppressing properties. In addition, through the analysis of the TG‐IR and Raman spectrum of residual char, the specific mechanism of flame retardance and smoke suppression was explored.     

Novel nanocomposites based on epoxy resin and modified magnesium hydroxide: Focus on flame retardancy and mechanical properties

In this work, a novel multifunctional organic‐inorganic hybrid flame agent (AM‐MEL) was prepared from magnesium hydroxide nanosheets decorated by nitrilotrimethylene triphosphonic acid and melamine. Then, an intrinsic flame‐retardant epoxy resin (EP) was prepared by covalently incorporating AM‐MEL nanoparticles. Meanwhile, ammonium polyphosphate (APP) was added into EP to form an intumescent flame retardant system with AM‐MEL. The chemical structure of AM‐MEL was characterized by Fourier transform infrared spectra, X‐ray photoelectron spectroscopy, and scanning electron microscopy. With the incorporation of 5 wt% AM‐MEL and 15 wt% APP, EP/AM‐MEL/APP could reach a limiting oxygen index value of 32.0% and achieve UL‐94 V‐0 rating, along with 88.0%, 70.0%, 81.5%, and 87.3% decrease in the peak heat release rate, total heat release, total smoke production, and the peak CO production rate, respectively, with respect to that of pure EP. The mechanisms of its flame retardant and smoke suppression were investigated.     

DOPO衍生物改性碳纳米管的制备及对聚乳酸阻燃性能的影响

以含羧基的碳纳米管(CNT-COOH)和9,10-二氢-9-氧-10-磷杂菲-10-氧化物(DOPO)衍生物DOPO-NH₂为原料, 通过酰氯化反应、 缩合反应等制备了一种新型无机-有机杂化阻燃剂—DOPO衍生物改性碳纳米管(CNT-DOPO), 利用傅里叶变换红外光谱、 透射电子显微镜、 X射线光电子能谱及热重分析等对其结构进行表征并对有机物接枝率进行了定量测试. 结果表明, DOPO-NH₂成功接枝到碳纳米管上, 接枝率约为50%. 将CNT-COOH, DOPO-NH₂和CNT-DOPO以质量分数5%添加到聚乳酸(PLA)中制备阻燃PLA复合材料. 锥形量热测试结果表明, 与纯PLA相比, PLA/5CNT-COOH, PLA/5DOPO-NH₂和PLA/5CNT-DOPO 3种复合材料的热释放速率峰值分别下降46%, 3.4%和39.8%; 炭层形貌和结构分析表明, PLA/5CNT-DOPO的炭层石墨化程度最高, CNT-DOPO₂在凝聚相阻燃方面有明显的促进作用. 流变结果表明, 碳纳米管对黏弹转变影响很明显, PLA/5CNT-COOH和PLA/5CNT-DOPO基本上表现为弹性行为. 正是由于碳纳米管的存在, 使得PLA复合材料在低频区黏度增大, 并且在燃烧后期形成了连续致密的炭层, 有效降低了材料的热释放速率和烟释放.     

静电自组装方法合成的具有多孔三维网络结构的Fe_3O_4/石墨烯复合材料作为高性能锂离子电池负极材料(英文)

采用静电自组装方法,分两步合成Fe(OH)3/GO前驱体(GO:氧化石墨烯),再通过水热反应和600°C高纯氮气气氛下煅烧,获得了Fe3O4/石墨烯复合材料.通过X射线衍射(XRD)、扫描电镜(SEM)、高分辨透射电镜(HRTEM)、拉曼(Raman)光谱等多种分析,发现该复合材料具有三维多孔石墨烯网络结构.把合成的这种Fe3O4/石墨烯复合材料作为锂离子电池负极材料,电化学测试结果表明其具有优良的电化学性能:首次放电容量为1390 mAh·g-1,50次循环后容量为819 mAh·g-1.通过对比实验表明,三维石墨烯网络结构的形成对复合材料的电化学循环稳定性起着关键作用.     

Synthesis of DOPO‐based pyrazine derivative and its effect on flame retardancy and thermal stability of epoxy resin

A novel DOPO‐based pyrazine derivative 6‐((2‐hydroxyphenyl)(pyrazin‐2‐ylamino)methyl)dibenzo[c,e][1,2]oxaphosphinine 6‐oxide (DHBAP) was triumphantly synthesized by a two‐step addition reaction using 2‐aminopyrazine, 2‐hydroxybenzaldehyde and 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO) as reactants, and characterized by Fourier‐transform infrared (FTIR), ³¹P nuclear magnetic resonance (NMR) and ¹H NMR. Afterwards, the addition type flame retardant (DHBAP) was utilized to modify epoxy resin (EP) by blending method. When the content of DHBAP in neat EP was 8 wt%, it reached to the V‐0 rating and the limited oxygen index (LOI) value up to 34.0%. Furthermore, according to the cone calorimeter (CC) test results, the heat release rate (HRR), total heat release (THR), smoke produce rate (SPR) and total smoke production (TSP) of EP/8% DHBAP decreased by 26.3%, 21.3%, 37.0% and 60.9% when compared with neat EP, respectively, indicating that DHBAP had good inhibition on heat and smoke releases. Eventually, the flame‐retardant mechanism of DHBAP was further explored by X‐ray photoelectron spectroscopy (XPS), Raman spectroscopy, and pyrolysis‐gas chromatography/mass spectrometry (Py‐GC/MS). The results showed that DHBAP had good flame‐retardant activity in the gasous‐condensed two phases.     

A novel intumescent flame retardant imparts high flame retardancy to epoxy resin

Intumescent flame retardant (IFR) has received the considerable attention ascribed to the inherent advantages including non‐halogen, low toxicity, low smoke release and environmentally friendly. In this work, a novel charring agent poly (piperazine phenylaminophosphamide) named as PPTA was successfully synthesized and characterized by Fourier transform infrared spectra (FTIR) and X‐ray photoelectron spectroscopy (XPS). Then, a series of flame‐retardant EP samples were prepared by blending with ammonium polyphosphate (APP) and PPTA. Combustion tests include oxygen Index (LOI), vertical Burning Test (UL‐94) and cone calorimeter testing,these test results showed that PPTA greatly enhances the flame retardancy of EP/APP. According to detailed results, EP containing 10 wt% APP had a LOI value of 30.2%,but had no enhancement on UL‐94 rating. However, after both 7.5 wt% APP and 2.5 wt% PPTA were added, EP‐7 passed UL‐94 V‐0 rating with a LOI value of 33.0%. Moreover, the peak heat release rate (PHRR) and peak of smoke product rate (PSPR) of EP‐7 were greatly decreased. Meanwhile, the flame‐retardant mechanism of EP‐7 was investigated by scanning electron microscopy (SEM), thermogravimetric analysis/infrared spectrometry (TG‐IR) and X‐ray photoelectron spectroscopy (XPS). The corresponding results presented PPTA significantly increased the density of char layer, resulting in the good flame retardancy.     

Synthesis of a caged bicyclic phosphates derived anhydride and its performance as a flame‐retardant curing agent for epoxy resins

A novel curing and flame‐retardant agent (PEPA‐TMAC) was successfully synthesized. The chemical structure was characterized by Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance (NMR). Use of PEPA‐TMAC as part of the curing agent in combination with another anhydride for a commercial epoxy resin (EP) was studied. Results of differential scanning calorimetry (DSC) indicated that PEPA‐TMAC was an effective curing agent for EP. The dynamic mechanical analysis (DMA) results showed that the glass transition temperature (T_g) and cross‐linking density (V_e) of EP composites exhibited an increase trend with the addition of PEPA‐TMAC. The limiting oxygen index (LOI) value of EP composites reached 26.9%, and the cone calorimeter results indicated that peak heat release rate (PHRR), total heat release (THR), smoke produce rate (SPR), and total smoke produce (TSP) remarkably decreased with increasing PEPA‐TMAC content. TGA data showed that the addition of PEPA‐TMAC greatly increased the amount of residual char during combustion. The morphology of the residual char was studied by SEM and showed that the addition of PEPA‐TMAC greatly increased the stability of EP composites. The thermogravimetric analysis (TGA), energy‐dispersive X‐ray spectroscopy (EDS), and FTIR results revealed the flame‐retardant mechanism that PEPA‐TMAC can promote the formation of charred layers with the phospho‐carbonaceous complexes in the condensed phase during burning of EP composites.     

三聚氰胺聚磷酸盐/季戊四醇配比、协效剂组及表面改性对聚丙烯基木塑复合材料的膨胀阻燃影响

通过极限氧指数(LOI)、线性燃烧速率(LBR)、热重分析和锥形量热分析等技术手段研究膨胀型阻燃剂(IFRs)中三聚氰胺聚磷酸盐(MPP)和季戊四醇(PER)的质量比、组成为m(MgO):m(可膨胀石墨,EG):m(SiO₂)=1:5:5的协效剂组(MgO/EG/SiO₂)和硅烷偶联剂(KH550)对聚丙烯基木塑复合材料(WPC)阻燃性能的影响。 结果表明,当IFRs中m(MPP):m(PER)=23:2(IFRs-M1)、质量分数为25%时的阻燃性能最佳,膨胀阻燃复合材料WPC/IFRs-M1的LOI和LBR分别为27.1%和3.89 mm/min,较未添加的WPC分别提高48.1%和下降89.79%,燃烧时的热释放速率、总热释放量、总烟释放量和CO₂释放量分别降低了76.2%、50.1%、6.9%和65.4%,600 ℃时的残炭率提高了498.3%。 协效剂组和KH550表面处理均可进一步改善WPC/IFRs-M1的阻燃性能,均对IFRs-M1具有良好的阻燃增效作用。 相比于WPC/IFRs-M1,同时用这两种阻燃增效手段的WPC/IFRs-M1/MgO/EG/SiO₂/KH550,其LOI提高了3.7%,LBR降低了20.3%;材料的热稳定性明显提高,热失重降低;燃烧时的热释放速率、总热释放量、总烟释放量和CO₂释放量分别降低了36.5%、37.6%、57.5%和33.33%,600 ℃时的残炭率提高了84.02%,显示出二者更好的协同效应。