Liquid Crystal Ordering on Conjugated Polymers Film Morphology for High Performance

The electronic performance of conjugated polymers depends on the microstructure of the polymer films. A percolated network morphology with high crystallinity, ordered intermolecular packing and long‐range order is beneficial for charge transport. In recent reports, some conjugated polymers have been shown to exhibit liquid crystallinity. The appearance of liquid crystalline ordering provides a new solution to solve the difficulties in microstructure manipulation. In this review, we summarize how liquid crystallinity can assist molecular arrangement and guide long‐range orientation during film processing, leading to high charge mobility. We expect that this article could draw more attention to the liquid crystallinity of conjugated polymers. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1572–1591     

Self‐Assembly of Poly(vinylpyridine‐b‐oligo(ethylene glycol) methyl ether methacrylate) Diblock Copolymers

Poly(oligoethylene glycol)‐poly(2‐vinylpyridine) is a model diblock for studying the effect of block‐localized charge on block copolymer self‐assembly because in the absence of charge the polymers are perfectly miscible, and upon protonation of the vinylpyridine block the polymer undergoes an order–disorder transition. Seven model block copolymers with molecular weights of approximately 60 kDa containing poly(2‐vinylpyridine) volume fractions spanning 0.069–0.700 were synthesized using reversible addition fragmentation transfer polymerization and then studied to understand the effect of protonation level, diblock composition, and temperature on the location of the ordering transition and the type of nanostructures formed in a charge asymmetric system. All of the polymers displayed lower critical solution‐type behavior, with the order–disorder transition temperature decreasing with increasing acid content. Polymers with symmetric compositions showed the highest degree of incompatibility for a given degree of protonation, and the observed morphologies for all polymers were consistent with those observed at similar compositions for classical hydrophobic block copolymers. The observed protonation‐induced phase transition can be explained by the shift of the Flory–Huggins parameter due to the alternation of the identity of monomers, consistent with the prediction of Nakamura and Wang's theory. The use of polyvalent ions promotes self‐assembly at lower concentrations, consistent with ionic crosslinking effects between polymer chains that are promoted at high concentration due to exchange entropy in crosslinked polymers. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1181–1190     

Long‐range order in physical networks of gel‐forming triblock copolymer solutions

Structural studies on physical gels, based on a triblock copolymer and a solvent selective for its midblocks, are presented. Gel formation in such systems arises due to interconnected microdomains that form the junctions in a three‐dimensional network. Small angle X‐ray scattering studies revealed that the physical networks show either short‐range order, described by an effective hard sphere model, or long‐range order, where junctions are arranged on a cubic lattice. The emerging morphology depends on the thermal conditions during preparation of such systems, which essentially reflects a competition among microdomain ordering and formation of the physical network. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1833–1840, 1999     

Controlled co‐solvent vapor annealing and the importance of quenching conditions in thin‐film block copolymer self‐assembly

A controlled co‐solvent vapor annealing system was designed and constructed to investigate the effects of solvent vapor activity during the rapid ambient quenching process on the morphology of a cylinder‐forming poly(styrene)‐b‐poly (ethylene oxide) (PS‐PEO) annealed in toluene and water vapor. A phase transformation from cylinders in the bulk to close‐packed spheres in swollen thin films occurred, which was reversed upon quenching with dry nitrogen. Quenching with humidified nitrogen preserved the spherical morphology but could significantly alter domain spacing and reduce long‐range order in the dried films under some circumstances. Specifically, long‐range order in the quenched films was found to decrease as the quenching humidity decreased from the humidity used during annealing, and the best long‐range order was obtained when the humidity remained consistent throughout both annealing and quenching. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1125–1130     

Bulky side chain effect of poly(N‐vinylcarbazole)‐based stacked polymer electrets on device performance parameters of transistor memories

Three poly(N‐vinylcarbazole) (PVK)‐based polymer electrets were synthesized through Friedel‐Crafts postfunctionalization for the function of charge storage in nonvolatile organic field effect transistor (OFET) memory devices. The bulky side chain effect of these stacked polymer electrets on the morphology, water contact angles, and memory characteristics were examined with regard to those of precursor PVK. The introduction of steric hindrance groups could interrupt the large length of π‐stacked structures in PVK and block the form of region‐regular structures from region‐random on external electric field. As a result, the memories based on the three modified polymers exhibited approximate memory windows of 32 V increased by 13 V with respect to PVK. Besides, the write‐read‐erase‐read cycles stability of the modified polymers was superior to that of PVK. Furthermore, we found that the holes were mainly located in the region of local π‐stacked structures and bulky π‐conjugated groups also acted as additional electron trapping sites. Molecular engineering of charge trapping site with tunneling polymers will be a promise strategy for the advance of transistor memory. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3554–3564     

Regioirregular ambipolar naphthalenediimide‐based alternating polymers: Synthesis,characterization, and application in field‐effect transistors

In this work, we report the synthesis, characterization, and application of two regioirregular naphthalenediimide (NDI)‐based alternating conjugated polymers, namely P1 and P2 , in which nitrile‐substituted moiety, 2,3‐bis(thiophen‐2‐yl)acrylonitrile and NDI moiety act as donor and acceptor unit, respectively. The two regioirregular polymers possess low‐lying LUMO energy levels of ?3.92 eV for P1 and ?3.96 eV for P2 . Both polymers possess typical dual‐band UV?Vis?NIR absorption profiles of NDI‐based polymers, and show broadened and red‐shifted absorption spectra in the solid state compared with those in solutions. Field‐effect transistor devices with top‐gate bottom‐contact configuration were used to evaluate the polymers' semiconducting properties. The two polymers exhibited promising and air‐stable ambipolar charge transport characteristics. Thin film microstructure investigations (AFM and 2D‐GIXRD) suggest both polymers formed continuous and smooth thin films, and adopted predominantly face‐on molecular packing in the solid state. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 3627–3635     

In situ grazing incidence small‐angle X‐ray scattering study of solvent vapor annealing in lamellae‐forming block copolymer thin films: Trade‐off of defects in deswelling

Solvent vapor annealing (SVA) is one route to prepare block copolymer (BCP) thin films with long‐range lateral ordering. The lattice defects in the spin‐coated BCP thin film can be effectively and rapidly reduced using SVA. The solvent evaporation after annealing was shown to have a significant impact on the in‐plane ordering of BCP microdomains. However, the effect of solvent evaporation on the out‐of‐plane defects in BCPs has not been considered. Using grazing‐incidence x‐ray scattering, the morphology evolution of lamellae‐forming poly(2‐vinlypyridine)‐b‐polystyrene‐b‐poly(2vinylpyridine) triblock copolymers, having lamellar microdomains oriented normal to substrate surface during SVA, was studied in this work. A micelle to lamellae transformation was observed during solvent uptake. The influence of solvent swelling ratio and solvent removal rate on both the in‐plane and out‐of‐plane defect density was studied. It shows that there is a trade‐off between the in‐plane and out‐of‐plane defect densities during solvent evaporation. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 980–989     

Two‐Dimensional Conducting Polymers: Synthesis and Charge Transport

Current technological advances and prolific endeavors have entrenched two‐dimensional conducting polymers as the rapidly emerging interface across a diversity of functional materials for flexible electronics, sensors, ion‐exchange membranes, biotechnology, catalysis, energy storage, and conversion. Rational design and fabrication of polymeric nanostructures enriched with well‐ordered geometry are appealing and endorse significant impact on their in‐built electrical, optical, and mechanical properties. In particular, recent interest in controlled hierarchical assembly of monomers/oligomers proved the free‐standing sheet‐like structures with exotic features of high conductivity and flexibility. Yet, the ongoing research to make nanometer‐thick polymers suffers from limitations to access large‐area, mechanical stability, and high‐range internal ordering. In this perspective, we focus on the radical approaches that highlight confinement‐entitled features of two‐dimensional polymeric materials correlating to their interface or template‐assisted synthesis, structure–property relationship, charge transport properties, and future scopes for relevant practical enactments. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1169–1176     

Ambipolar charge transport in a donor–acceptor–donor‐type conjugated block copolymer and its gate‐voltage‐controlled thin film transistor memory

We demonstrate a fully conjugated donor–acceptor–donor (D–A–D) triblock copolymer, PBDTT–PNDIBT–PBDTT, which contains PBDTT as the donor block and PNDIBT as the acceptor block. The polymer was synthesized by end‐capping each block with a reactive unit, followed by condensation copolymerization between the two blocks. The physical, optical, and electrochemical properties of the polymer were investigated by comparing those of donor‐ and acceptor‐homopolymers (i.e., PBDTT and PNDIBT), which are the oligomeric monomers, and their blends. On using the newly synthesized block copolymer, ambipolar charge transport behavior was observed in the corresponding thin‐film transistor, and the behavior was compared to that of blend film of donor‐ and acceptor‐homopolymers. Owing to the presence of donor and acceptor blocks in a single polymer chain, it was found that the triblock copolymer can store two‐level information; the ability to store this information is one of the most intriguing challenges in memory applications. In this study, we confirmed the potential of the triblock copolymer in achieving distinct two‐stage data storage by utilizing the ambipolar charge trapping phenomenon, which is expected in donor and acceptor containing random and block copolymers in a thin‐film transistor. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3223–3235     

Dithieno[2,3‐d:2',3'‐d']benzo[1,2‐b:4,5‐b']dithiophene (DTBDAT)‐based copolymers for high‐performance organic solar cells

P(BDT‐TCNT) and P(DTBDAT‐TCNT) , which has an extended conjugation length, were designed and synthesized for applications in organic solar cell (OSCs). The solution absorption maxima of P(DTBDAT‐TCNT) with the extended conjugation were red‐shifted by 5–15 nm compared with those of P(BDT‐TCNT) . The optical band gaps and highest occupied molecular orbital (HOMO) energy levels of both P(BDT‐TCNT) and P(DTBDAT‐TCNT) were similar. The structure properties of thin films of these materials were characterized using grazing‐incidence wide‐angle X‐ray scattering and tapping‐mode atomic force microscopy, and charge carrier mobilities were characterized using the space‐charge limited current method. OSCs were formed using [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) as the electron acceptor and 3% diphenylether as additive suppress aggregation. OSCs with P(BDT‐TCNT) as the electron donor exhibited a power conversion efficiency (PCE) of 4.10% with a short‐circuit current density of J_SC = 9.06 mA/cm², an open‐circuit voltage of V_OC = 0.77 V, and a fill factor of FF = 0.58. OSCs formed using P(DTBDAT‐TCNT) as the electron donor layer exhibited a PCE of 5.83% with J_SC = 12.2 mA/cm², V_OC = 0.77 V, and FF = 0.62. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3182–3192     

Effect of polydispersity on the bulk‐heterojunction morphology of P3HT:PCBM solar cells

Bulk heterojunctions (BHJs) based on semiconducting electron–donor polymer and electron–acceptor fullerene have been extensively investigated as potential photoactive layers for organic solar cells (OSCs). In the experimental studies, poly‐(3‐hexyl‐thiophene) (P3HT) polymers are hardly monodisperse as the synthesis of highly monodisperse polymer mixture is a near impossible task to achieve. However, the majority of the computational efforts on P3HT: phenyl‐C61‐butyric acid methyl ester (P3HT:PCBM)‐based OSCs, a monodisperse P3HT is usually considered. Here, results from coarse‐grained molecular dynamics simulations of solvent evaporation and thermal annealing process of the BHJ are shared describing the effect of variability in molecular weight (also known as polydispersity) on the morphology of the active layer. Results affirm that polydispersity is beneficial for charge separation as the interfacial area is observed to increase with higher dispersity. Calculations of percolation and orientation tensors, on the other hand, reveal that a certain polydispersity index ranging between 1.05 and 1.10 should be maintained for optimal charge transport. Most importantly, these results point out that the consideration of polydispersity should be considered in computational studies of polymer‐based OSCs. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 895–903     

EDOT‐diketopyrrolopyrrole copolymers for high bulk hole mobility and near infrared absorption

To obtain novel low‐bandgap materials with tailored hole‐transport properties and extended absorption, electron rich 3,4‐ethylenedioxythiophene is introduced as a comonomer in diketopyrrolo[3,4‐c]pyrrole copolymers with different aryl flanking units. The polymers are characterized by absorption and photoluminescence spectroscopy, dynamic scanning calorimetry, cyclic voltammetry, and X‐ray diffraction. The charge transport properties of these new materials are studied carefully using an organic field effect transistor geometry where the charge carriers are transported over a narrow channel at the semiconductor/dielectric interface. These results are compared to bulk charge carrier mobilities using space‐charge limited current (SCLC) measurements, in which the charge carrier is transported through the complete film thickness of several hundred nanometers. Finally, charge carrier mobilities are correlated with the electronic structure of the compounds. We find that in particular the thiophene‐flanked copolymer PDPP[T]₂‐EDOT is a very promising candidate for organic photovoltaics, showing an absorption response in the near infrared region with an optical bandgap of 1.15 eV and a very high bulk hole mobility of 2.9 × 10^?4 cm² V^?1 s^?1 as measured by SCLC. This value is two orders of magnitudes higher than SCLC mobilities reported for other polydiketopyrrolopyrroles and is in the range of the well‐known hole transporting polymer poly(3‐hexylthiophene). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 639–648     

Enhanced efficiency of ternary organic solar cells by doping a polymer material in P3HT:PC61BM

Doping a low‐bandgap polymer material (PDTBDT‐DTNT) as a complementary electron donor in poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C₆₁‐butyricacid methyl ester (PC₆₁BM) blend is experimented to improve the power conversion efficiency (PCE) of organic solar cells (OSCs). The PCE of OSCs was increased from 3.19% to 3.75% by doping 10 wt% PDTBDT‐DTNT, which was 17.55% higher than that of the OSCs based on binary blend of P3HT:PC₆₁BM (host cells). The short‐circuit current density (J_sc) was increased to 10.11 mA·cm⁻² compared with the host cells. Although the PCE improvement could partly be attributed to more photon harvest for complementary absorption of 2 donors by doping appropriate PDTBDT‐DTNT, the promotion of charge separation and transport as well as the suppression of charge recombination due to a matrix of cascade energy levels is also important. And the better morphology of the active layer films is beneficial to the optimized performance of ternary devices.     

Controlling open‐shell loading in norbornene‐based radical polymers modulates the solid‐state charge transport exponentially

Radical polymers are an emerging class of electronically active macromolecules; however, the fundamental mechanism by which charge is transferred in these polymers has yet to be established in full. To address this issue, well‐defined norbornene‐based nitroxide radical polymers were synthesized using the controlled ring‐opening metathesis polymerization technique. These polymers were blended in solution with a quenched, electrically insulating hydroxylamine derivative to dilute the radical content of the system. Electron paramagnetic resonance spectroscopy data were used to characterize the radical content as well as to reveal that hydrogen atom transfer occurred between the open‐shell and closed‐shell polynorbornene derivatives when they were blended in solution. Using these platform macromolecules, we demonstrate that the systematic manipulation of the radical content in open‐shell macromolecules leads to exponential changes in the macroscopic electrical conductivity. When coupled with the fact that these materials show a clear temperature‐independent charge transport behavior, a picture emerges that charge transfer in radical polymers is dictated by a tunneling mechanism between localized donor and acceptor sites within the redox‐active thin films. These results constitute the first experimental insight into the mechanism of solid‐state electrical conduction in radical polymers, and this provides a design paradigm for open‐shell macromolecular charge transport. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1516–1525     

Correlation of charge transport with structural order in highly ordered melt‐crystallized poly(3‐hexylthiophene) thin films

A series of well‐defined poly(3‐hexylthiophene)s (P3HT) of different molecular weight (MW) and high regioregularity was investigated for charge transport properties in as‐cast and melt‐crystallized films. The semicrystalline structure of the P3HT was characterized by X‐ray scattering and Atomic force microscopy. Crystallization by cooling from the melt led to a substantial increase in crystallinity and a stronger alignment of the crystals in comparison to as‐cast films. The increase in crystallinity went along with an increase in hole mobility of up to an order of magnitude as measured by the space charge limited current method. Additionally, the hole mobility depended on the long period of P3HT lamellae and consequently on the MW. In compliance with the long period, the charge carrier mobility first increased with the MW before decreasing again at the onset of chain folding. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 943–951     

Iodinated polyesters as a versatile platform for radiopaque biomaterials

The design of polymeric biomaterials with long‐lasting X‐ray contrast could advance safe and effective implants and contrast agents. Herein, a new set of wholly aliphatic, iodinated polyesters are synthesized and evaluated as high‐contrast biomaterials and nanoparticle contrast agents for general computed tomography imaging. A single iodinated monomer is used to synthesize a variety of aliphatic polyesters with tunable thermal and mechanical properties. These iodinated polyesters are end‐functionalized with a photocurable methacrylate group, which allows easy processability. The resulting materials exhibit no cytotoxicity and are radiopaque, containing over 40% iodine by weight after processing. The polymers can be formulated into lipid–polymer hybrid nanoparticles using a modified nanoprecipitation method. Initial studies indicate that these nanoparticles show good continual contrast over 60 minutes with no uptake into the kidneys. The work presented here illustrates a novel platform for iodinated polyesters that exhibit high radiopacity and processability, low cost, and no cytotoxicity. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2171–2177     

Electrohydrodynamics of spherical polyampholyte‐grafted nanoparticles: Multiscale simulations by coupling of molecular dynamics and lattice‐boltzmann method

We perform multiscale simulations based on the coupling of molecular dynamics and lattice‐Boltzmann (LB) method to study the electrohydrodynamics of a polyampholyte‐grafted spherical nanoparticle. The long‐range hydrodynamic interactions are modeled by coupling the movement of particles to a LB fluid. Our results indicate that the net‐neutral soft particle moves with a nonzero mobility under applied electric fields. We systematically explore the effects of different parameters, including the chain length, grafting density, electric field, and charge sequence, on the structures of the polymer layer and the electrophoretic mobility of the soft particle. It shows that the mobility of nanoparticles has remarkable dependence on these parameters. We find that the deformation of the polyampholyte chains and the ion distribution play dominant roles in modulating the electrokinetic behavior of the polyampholyte‐grafted particle. The enhancement or reduction in the accumulation of counterions around monomers can be attributed to the polymer layer structure and the conformational transition of the chains in the electric field. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1435–1447     

Synthesis and FET characterization of novel ambipolar and low‐bandgap naphthalene‐diimide‐based semiconducting polymers

A novel series of naphthalene‐diimide‐based semiconducting polymers ( P1–P4 ) containing benzodithiophene or dithienopyrrole were successfully synthesized for ambipolar semiconducting materials showing near infrared absorptions. The incorporation of a 3‐hexylthiophene (3HT) spacer extended the intramolecular charge‐transfer (ICT) peak from λ_onset = 739 nm ( P1 ) to 785 nm ( P3 ). Moreover, about 250 nm red‐shift of the ICT peaks was observed in P2 and P4 compared to P1 and P3 due to the increased high‐lying HOMO energy levels. The grazing incidence X‐ray scattering of the P3 and P4 films proved the slightly improved crystalline order in the π?π stacking direction, indicating that the planar backbone is probably due to the introduced 3HT. The P1–P4 ‐based field‐effect transistor showed n‐type dominant ambipolar characteristics. The P2 and P4 showed higher electron mobilities up to 1.5 × 10^?2 cm² V^?1 s^?1 than P1 and P3 , which might be influenced by the orientation of the polymer backbone and the intermolecular orbital overlap. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 359–367     

Temperature dependence of molecular conformation in uniaxially deformed isotactic polypropylene investigated by combination of polarized FTIR spectroscopy and 2D correlation analysis

Evolution of molecular conformation in uniaxially deformed isotactic polypropylene (iPP) as a function of temperature is investigated by time‐resolved polarized Fourier‐transform infrared spectroscopy. It is observed that oriented crystals (microfibrils) induced by deformation possess better thermal stability compared with isotropic spherulites. 2D correlation analysis reveals that the relaxation process of ordered helices in deformed iPP could be divided into two regions referring to the melting of different crystalline structures. No obvious sequential change of ordering conformations observed in low temperature region is attributed to melting of defective or destructed crystals. However, notable sequential changes of helices occur in the high temperature region; interestingly, long helices are more thermally stable than short helices. The central region of microfibrils is suggested to consist of a large amount of long helical bundles, and the short ordering segments are primarily located in the outer lateral surfaces. A physical picture of the conformational distribution in deformation‐induced microfibrils is thus gained. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 673–684