嵌入式超薄微晶纤维素/碳糊电极的构建及应用

以镍铬合金为基体,在其表面通过直接嵌入微晶纤维素修饰的碳糊膜,构建了嵌入式超薄微晶纤维素/碳糊电极(ISM/CPE). 用扫描电子显微镜和循环伏安法表征了电极的特性;以抗坏血酸(AA)为目标物考察其在该电极上的电化学行为. 结果表明,在ISM/CPE上,AA的氧化峰电位为0.38 V,较传统碳糊电极负移了0.05 V;峰电流与AA的浓度在1.0×10-6～1.0×10-3 mol/L范围内呈良好线性关系,相关系数r=0.999 3,检测限(S/N=3)为7.5×10-7 mol/L. 表明合金表面嵌入的超薄微晶纤维素/碳糊膜,改变了基体电极的电化学性质,可用于实际样品中AA的测定.     

抗坏血酸在预阳极化嵌入式超薄碳糊电极上的电化学行为

以镍铬合金为基体,直接在其表面嵌入碳糊构建了嵌入式超薄碳糊(IUCP)前驱膜,然后对其表面进行电化学处理,制备了预阳极化嵌入式超薄碳糊电极(PAIUCPE).扫描电镜表征其形貌,伏安法检验其电化学性能,并以抗坏血酸(AA)为目标物考察PAIUCPE对AA的电化学响应情况,该电极制备非常简单、实验成本极其低廉,可直接用于...     

纳米电极界面的构建和茶碱的直接电氧化测定

以镍铬合金为基体制备嵌入式超薄碳糊前驱膜,然后在薄膜表面构筑单壁碳纳米管/聚L-酪氨酸复合电极.SEM结果表明膜表面的碳纳米管复合物呈立体枝状渗透性结构,电化学实验证明表面膜上的复合纳米结构改变了基体的电化学性质,使之可用作研究电极.以茶碱为目标物考察其在该电极上的伏安行为,在0.1 mol/L的HClO4底液中,茶碱的2.5次微分峰电流与其浓度在1.0×10-6～8.0×10-4 mol/L 范围内呈良好的线性关系,相关系数为0.9971,方法可用于茶碱的定量测定.     

碳纳米管复合聚合物电极的构建及对色氨酸和5-羟基色氨酸的同时电化学测定

以镍铬合金为基体,首先通过嵌压技术在其表面置入厚度约为100 nm的碳糊前驱膜,然后结合SWNTs和聚合物膜的特性,构建了单壁碳纳米管复合聚对氨基苯甲酸修饰的嵌入式超薄碳糊电极(SWNTs/PABAE).SWNTs/PABAE改变了基体材料的电化学性质,使其可用作电化学研究电极,并用于色氨酸(Trp)和5-羟基色氨酸(5-HTP)的同时电化学行为研究,获得满意的结果.     

嵌入式超薄化学修饰碳糊电极及抗坏血酸的电化学行为研究

以镍铬合金为基体,在其表面构建了嵌入式超薄邻啡口罗啉修饰碳糊电极,以扫描电镜表征电极形貌、电化学技术研究电极的电化学性质。该电极对抗坏血酸(AA)有灵敏的响应,在pH 2.0的B.R.缓冲溶液中,AA的氧化峰电流与其浓度在1.0×10-7~1.0×10-4mol/L范围内呈良好的线性关系,检出限为6.0×10-8mol/L。该电极可用于AA的电化学测量。     

球型Pt微粒电极的构建及其对甲醇电氧化的研究

以镍铬合金为基体,在其表面电化学沉积制备了Pt微粒电极,用扫描电子显微镜（SEM）对电极的表面形貌进行了表征,电化学方法考察了电极的电化学性能和甲醇在该电极上的电催化行为．结果表明镍铬合金表面沉积的球型Pt微粒电极对甲醇的电氧化具有良好的催化活性,相同实验条件下,该电极的催化活性比纯Pt电极高30倍．该电极对甲醇的电氧化显示出较高的催化性能．     

嵌入式超薄碳糊电极的研究及其应用

在镍铬合金基体上,研制了一种新颖的嵌入式超薄碳糊膜电极。该电极可用作银离子的伏安测定。峰电流与Ag 离子浓度在1.0×10-10～1.0×10-6mol/L范围呈良好的线性关系,检出限为8.0×10-11mol/L。     

嵌入式超薄碳糊膜银离子传感器的研究

研制了一种新颖的超薄碳糊膜银离子传感电极 .在镍铬合金基体上通过嵌入碳糊薄膜而制得该电极 .用电位法研究了电极的响应特性 ,电极电位E (mV)与银离子浓度在 1.0× 10 -6～ 1.0× 10 -2 mol/L范围内呈良好的线性关系 ,相关系数为 0 .9998,检测限为 6.0× 10 -7mol/L ,对银离子的响应斜率为 5 8.3～ 60 .3mV/ ( -logcAg+ ) .电极制作简单、费用很低、稳定性良好 ,可用作银离子指示电极     

嵌入式超薄碳膜电极的伏安行为及其应用

以镍铬合金为基体,在其表面嵌入碳膜或碳纳米管,制备了超薄碳膜电极,并用于酚磺乙胺(ETA)的测定。超薄碳膜电极对ETA有良好的电催化作用和增敏作用,与玻碳电极相比,氧化峰电位负移120mV,还原峰电位正移160mV,电流响应明显增大。在最优条件下,ETA浓度在5×10-7 ~9×10-6 mol/L和9×10-6~6×10-5 mol/L之间与其氧化峰电流呈良好的线性关系,相关系数分别为0. 9967和0. 9979。该电极制备简便,价格低廉,用于酚磺乙胺的测定结果令人满意。     

嵌入式超薄碳糊膜电极伏安法同时测定黄嘌呤和次黄嘌呤

以镍铬合金为基体制备了嵌入式超薄碳糊膜电极,研究了黄嘌呤(Xa)和次黄嘌呤(Hxa)在该电极上的电化学行为。该电极对Xa和Hxa具有良好的电化学催化特性。两峰电位相差320mV。其氧化峰电流与Xa和Hxa的浓度在5.0×10-8～8.0×10-5mol/L和7.0×10-8～7.0×10-5mol/L范围内呈良好线性关系;检出限为2.0×10-10mol/L。电极制备简单,有良好的灵敏度、选择性和稳定性。该方法可用于人尿中Xa和Hxa的同时测定。     

Polystyrene sulphonate wrapped multiwalled carbon nanotubes modified graphite electrode for simultaneous determination of ascorbic acid, dopamine and uric acid

Graphite electrode is modified by casting multi-walled carbon nanotubes (MWCNTs) wrapped with polystyrene sulphonate (PSS) onto the surface of the bare graphite electrode. The modified electrode was characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The behavior of the modified electrode towards the oxidation of ascorbic acid (AA), dopamine (DA) and uric acid (UA) has been determined by cyclic voltammetry (CV), differential pulse voltammetry (DPV) and chronoamperometry (CA). The modified electrode showed better electrocatalytic activity towards AA, DA and UA compared to bare graphite electrode. The electrochemical oxidation signals of AA, DA and UA are well separated into three distinct peaks with peak potential difference of 222, 128 and 350 mV between AA-DA, DA-UA and AA-UA respectively in CV studies and corresponding peak potential separation in DPV are 228, 120 and 348 mV. This modified electrode was successfully used for simultaneous determination of AA, DA and UA in ternary mixture.     

聚色氨酸／镍复合膜修饰电极测定抗坏血酸的研究

采用电化学聚合法制备了聚色氨酸／镍复合膜修饰玻碳电极,研究了抗坏血酸在该修饰电极上的电化学行为,建立了测定痕量抗坏血酸的新方法。在pH6．2的磷酸盐缓冲溶液中,抗坏血酸在修饰电极上产生一个灵敏的氧化峰,采用线性扫描伏安法测定,其氧化峰电流与抗坏血酸浓度在2．0×10^-6 -1．0×10^-3mol／L范围内呈良好的线性关系,检出限为5．0×10^-7mol／L。对1．0×10^-4mol／L抗坏血酸溶液平行测定6次,测定结果的相对标准偏差为1．9％。该法用于片剂中抗坏血酸含量的测定,加标回收率为97．8％～101．2％。     

A glassy carbon electrode modified with the nickel(II)-bis(1,10-phenanthroline) complex and multi-walled carbon nanotubes, and its use as a sensor for ascorbic acid

A glassy carbon electrode (GCE) was modified with the nickel(II)-bis(1,10-phenanthroline) complex and with multi-walled carbon nanotubes (MWCNTs). The nickel complex was electrodeposited on the MWCNTs by cyclic voltammetry. The modified GCE displays excellent electrocatalytic activity to the oxidation of ascorbic acid (AA). The effects of fraction of MWCNTs, film thickness and pH values were optimized. Response to AA is linear in the 10 to 630 μM concentration range, and the detection limit is 4 μM (at a signal-to-noise ratio of 3:1). The modified electrode was applied to determine AA in vitamin C tablets and in spiked fruit juice.

Congo Red Immobilized on a Silica/Aniline Xerogel: Preparation and Application as an Amperometric Sensor for Ascorbic Acid

Congo red (CR) was immobilized on a silica/aniline xerogel through electrostatic interaction. The dye is strongly retained and is not easily leached from the xerogel matrix. The material containing the adsorbed dye was used to prepare a carbon paste electrode and the electrochemical properties of the hybrid material were investigated using cyclic voltammetry and amperometry. The modified electrode was used to study the electrochemical oxidation of ascorbic acid. The adsorbed dye mediates ascorbic acid oxidation at the solid electrode surface‐solution interface at an anodic potential of 0.18 V at pH 7, in a 0.5 mol L^?1 KCl solution. This novel modified carbon paste electrode shows good analytical performance for the determination of ascorbic acid in commercial Vitamin C tablets.     

Electrochemical Properties of Lanthanum Hexacyanoferrate Particles Immobilized onto Electrode Surface by Au‐Codeposition Method

Lanthanum hexacyanoferrate (LaHCF) was immobilized onto a substrate surface as an electroactive material by Au‐codeposition method. The LaHCF particles were attached to the electrode surface as the result of occlusion within the gold film deposited. This deposition method was first introduced for the preparation of hexacyanoferrate‐based modified electrodes. It was demonstrated that this deposition method provides a higher stability of the electroactive film in comparison with available methods for the mechanical attachment of electroactive films. On the other hand, electrochemical properties of the LaHCF film modified electrode were studied for the first time. The results showed that LaHCF film has excellent electrochemical activity as well as other analogues of Prussian blue. The modified electrode was successfully used as an electrocatalyst for the oxidation of ascorbic acid.     

Highly Sensitive Enzyme-free Sensor Based on a Carbon Paste Electrode Modified with Binary Zinc Oxide/Polyaniline Nanocomposites for Dopamine,Ascorbic Acid and Uric Acid Sensing

Hybrid composites ZnO/PANI were facily synthesized by a sonication process at room temperature. This procedure is non-expensive, time/energy saving and environmentally safe. The as-prepared ZnO/PANI were characterized by FTIR, UV-vis spectroscopies and SEM in order to investigate the structure and morphology of the studied composites. The samples were used to modify carbon paste electrode (CPE) in order to develop electrochemical biosensors (ZnO/PANI/CPE). The sensing properties of the nanoparticles were evaluated for dopamine, ascorbic acid and uric acid non-enzymatic detection. The effect of percentage of polyaniline in the composites and the effect of calcination on the biosensor's response were also examined in the present study. It was revealed that the existence of PANI in ZnO/PANI/CPE largely enhanced the electroactive surface area and therefore the sensitivity for electrochemical sensing. A good electrochemical behavior was noted for ZnO/40 wt% PANI-cal/CPE modified electrode toward DA, AA and UA oxidation. The electroactive surface area of the previously mentioned modified electrode (0.235 cm²) was two times higher than that of the bare electrode (0.117 cm²). The liner relationships between current intensities and concentrations were found to be 0.01–1.4 mM, 0.1–1.3 mM and 0.01–0.12 mM, with detection limit of 0.029 mM, 0.063 mM and 0.007 mM, for DA, AA and UA respectively. In the mixtures of ascorbic acid (AA), dopamine (DA) uric acid (UA) and glucose (Glu) the sensor showed high selectivity of DA with low interference of ascorbic acid by a current change of 14 %. The as-prepared ZnO/PANI/CPE biosensor displayed a good reproducibility and stability.     

聚对氨基苯磺酸/碳纳米管复合膜修饰电极对尿酸与抗坏血酸的同时测定

通过在碳纳米管修饰玻碳电极表面电聚合的方法制备了聚对氨基苯磺酸/碳纳米管复合膜修饰电极(PABSA/CNT/GC),采用扫描电镜对电极形貌进行了表征。运用循环伏安法研究了尿酸(UA)和抗坏血酸(AA)在该修饰电极上的电化学行为,在pH7.0的PBS中,UA和AA分别在0.312、-0.025 V处产生灵敏氧化峰,与其在聚氨基苯磺酸和碳纳米管单层膜修饰电极上的电化学行为相比,两者的氧化峰电流显著增加,峰电位差(ΔEpa)达到337 mV,表明碳纳米管和聚合物产生协同增效作用,探讨了其作用机理。在优化实验条件下,建立了差分脉冲伏安法同时测定UA和AA的方法,UA、AA的线性范围分别为2.5×10-7~5.0×10-4、8.0×10-6~4.0×10-3mol/L,检出限分别为7.5×10-8、5.0×10-6mol/L。该方法用于尿样中UA和AA的测定,结果令人满意。     

聚苯胺薄膜修饰电极对抗坏血酸的电催化氧化

本文表明聚苯胺(PAn)薄膜修饰电极对水溶液中的抗坏血酸(AH_2)在较宽的pH范围和较宽的浓度范围内均有良好的电催化氧化作用, 为EC平行催化过程。利用旋转圆盘电极(RDE)进行了催化过程动力学分析, 求出了催化反应动力学参数。在抗坏血酸浓度10~(-2)～10~(-6) mol·L~(-1)范围内, 催化峰电流与AH_2浓度均成良好的线性关系, 且PAn薄膜修饰电极具有很好的稳定性, 有应用分析抗坏血酸的意义。     

Preparation of tetraheptylammonium iodide-iodine graphite-multiwall carbon nanotube paste electrode: electrocatalytic determination of ascorbic acid in pharmaceuticals and foods

The present work describes the construction of a new modified graphite-multiwall carbon nanotube paste electrode by casting the appropriate mixture of tetraheptylammonium iodide-iodine as a new modifier. The modified paste electrode was used for the determination of ascorbic acid (AA) in a phosphate buffer solution (pH 2.0). When compared to activated carbon, a graphite and multiwall carbon nanotube paste electrode containing a new modifier, the proposed modified paste electrode not only shifted the oxidation potential of AA towards a less-positive potential but also enhanced its oxidation peak current. Further, the oxidation of AA was highly stable at the modified paste electrode. The optimum analytical conditions were sought. The current response of AA increases linearly while increasing its concentration from 5.6 × 10(-5) to 1.2 × 10(-2) M with a correlation coefficient of 0.9991; the detection limit (3σ) was found to be of 3.6 × 10(-5) M. The present modified paste electrode was also successfully used for the determination of AA in the presence of common interference compounds. The present modified electrode was successfully demonstrated towards the determination of AA in pharmaceutical and food samples.