Synthesis and characterization of poly(L‐lactic acid)–poly(ε‐caprolactone) multiblock copolymers by melt polycondensation

An Erratum has been published for this article in J. Polym. Sci. Part A: Polym. Chem. (2004) 42(22) 5845 New multiblock copolymers derived from poly(L‐lactic acid) (PLLA) and poly(ε‐caprolactone) (PCL) were prepared with the coupling reaction between PLLA and PCL oligomers with ? NCO terminals. Fourier transform infrared (FTIR), ¹³C NMR, and differential scanning calorimetry (DSC) were used to characterize the copolymers and the results showed that PLLA and PCL were coupled by the reaction between ? NCO groups at the end of the PCL and ? OH (or ? COOH) groups at the end of the PLLA. DSC data indicated that the different compositions of PLLA and PCL had an influence on the thermal and crystallization properties including the glass‐transition temperature (T_g), melting temperature (T_M), crystallizing temperature (T_c), melting enthalpy (ΔH_m), crystallizing enthalpy (ΔH_c), and crystallinity. Gel permeation chromatography (GPC) was employed to study the effect of the composition of PLLA and PCL and reaction time on the molecular weight and the molecular weight distribution of the copolymers. The weight‐average molecular weight of PLLA–PCL multiblock copolymers was up to 180,000 at a composition of 60% PLLA and 40% PCL, whereas that of the homopolymer of PLLA was only 14,000. A polarized optical microscope was used to observe the crystalline morphology of copolymers; the results showed that all polymers exhibited a spherulitic morphology. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5045–5053, 2004     

Preparation and characterization of biodegradable poly(lactic acid)‐ block‐poly(ε‐caprolactone) multiblock copolymer

Biodegradable copolymers of poly(lactic acid)‐block‐poly(ε‐caprolactone) (PLA‐b‐PCL) were successfully prepared by two steps. In the first step, lactic acid monomer is oligomerized to low molecular weight prepolymer and copolymerized with the (ε‐caprolactone) diol to prepolymer, and then the molecular weight is raised by joining prepolymer chains together using 1,6‐hexamethylene diisocyanate (HDI) as the chain extender. The polymer was carefully characterized by using ¹H‐NMR analysis, gel permeation chromatography (GPC), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and Fourier transform infrared spectroscopy (FTIR). The results of ¹H‐NMR and TGA indicate PLA‐b‐PCL prepolymer with number average molecular weights (M_n) of 4000–6000 were obtained. When PCL‐diols are 10 wt%, copolymer is better for chain extension reaction to obtain the polymer with high molecular weight. After chain extension, the weight average molecular weight can reach 250,000 g/mol, as determined by GPC, when the molar ratio of –NCO to –OH was 3:1. DSC curve showed that the degree of crystallization of PLA–PCL copolymer was low, even became amorphous after chain extended reaction. The product exhibits superior mechanical properties with elongation at break above 297% that is much higher than that of PLA chain extended products. Copyright © 2009 John Wiley & Sons, Ltd.     

Facile synthesis of AB2‐type miktoarm star polymers through the combination of atom transfer radical polymerization and ring‐opening polymerization

A novel miktofunctional initiator ( 1 ), 2‐hydroxyethyl 3‐[(2‐bromopropanoyl)oxy]‐2‐{[(2‐bromopropanoyl)oxy]methyl}‐2‐methyl‐propanoate, possessing one initiating site for ring‐opening polymerization (ROP) and two initiating sites for atom transfer radical polymerization (ATRP), was synthesized in a three‐step reaction sequence. This initiator was first used in the ROP of ?‐caprolactone, and this led to a corresponding polymer with secondary bromide end groups. The obtained poly(?‐caprolactone) (PCL) was then used as a macroinitiator for the ATRP of tert‐butyl acrylate or methyl methacrylate, and this resulted in AB₂‐type PCL–[poly(tert‐butyl acrylate)]₂ or PCL–[poly(methyl methacrylate)]₂ miktoarm star polymers with controlled molecular weights and low polydispersities (weight‐average molecular weight/number‐average molecular weight < 1.23) via the ROP–ATRP sequence. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2313–2320, 2004     

稀土硫化物：e–己内酯开环聚合新催化剂

The ring-opening polymerization （ROP） of ε-caprolactone （ε-CL） using lanthanide thiolate complexes [（CH3CsH4）2Sm（μ-SPh）（THF）]2 （1） and Sm（SPh）3（HMPA）3 （2） as initiators has been investigated for the first time. Both of 1 and 2 were found to be highly efficient initiators for the ROP of ε-CL. The poly（ε-caprolactone） （PCL） with molecular weight Mn up to 1.97 ×10^5 and relatively narrow molecular weight distributions （1.20〈MW/Mn〈 2.00） have been obtained in high yield in the temperature range of 35-65℃. According to the polymer yield, 2 showed much higher activity than 1. However, the number-average molecular weight of PCL obtained with 2 was much lower than with 1. The possible polymerization mechanism of the ε-CL polymerization has been proposed based on the results of the end group analysis of the ε-CL oligomer.     

Synthesis and characterization of well‐defined polystyrene and poly(ε‐caprolactone) hetero eight‐shaped copolymers

Well‐defined hetero eight‐shaped copolymers composed of polystyrene (PS) and poly(ε‐caprolactone) (PCL) with controlled molecular weight and narrow molecular weight distribution were successfully synthesized by the combination of ring‐opening polymerization, ATRP, and “click” reaction. The synthetic procedure involves three steps: (1) preparation of a tetrafunctional PS and PCL star copolymer with two PS and two PCL arms using the tetrafunctional initiator bearing two hydroxyl groups and two bromo groups; (2) synthesis of tetrafunctional star copolymer, (α‐acetylene‐PCL)₂(ω‐azido‐PS)₂, by the transition of terminal hydroxyl and bromo groups to acetylene and azido groups through the reaction with 4‐propargyloxybutanedioyl chloride and NaN₃ respectively; (3) intramolecular cyclization reaction to produce the hetero eight‐shaped copolymers using “click” chemistry under high dilution. The ¹H NMR, FTIR, and gel permeation chromatography techniques were applied to characterize the chemical structures of the resulted intermediates and the target polymers. Their thermal behavior was investigated by DSC, and their crystallization behaviors of PCL were studied by polarized optical microscopy. The decrease in chain mobility of the eight‐shaped copolymers restricts the crystallization of PCL and the crystallization rate of PCL is slower in comparison with their corresponding star precursors. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6496–6508, 2008     

Synthesis of biocompatible and biodegradable block copolymers of polyvinyl alcohol‐block‐poly(ε‐caprolactone) using metal‐free living cationic polymerization

Applications of metal‐free living cationic polymerization of vinyl ethers using HCl · Et₂O are reported. Product of poly(vinyl ether)s possessing functional end groups such as hydroxyethyl groups with predicted molecular weights was used as a macroinitiator in activated monomer cationic polymerization of ε‐caprolactone (CL) with HCl · Et₂O as a ring‐opening polymerization. This combination method is a metal‐free polymerization using HCl · Et₂O. The formation of poly(isobutyl vinyl ether)‐b‐poly(ε‐caprolactone) (PIBVE‐b‐PCL) and poly(tert‐butyl vinyl ether)‐b‐poly(ε‐caprolactone) (PTBVE‐b‐PCL) from two vinyl ethers and CL was successful. Therefore, we synthesized novel amphiphilic, biocompatible, and biodegradable block copolymers comprised polyvinyl alcohol and PCL, namely PVA‐b‐PCL by transformation of acid hydrolysis of tert‐butoxy moiety of PTBVE in PTBVE‐b‐PCL. The synthesized copolymers showed well‐defined structure and narrow molecular weight distribution. The structure of resulting block copolymers was confirmed by ¹H NMR, size exclusion chromatography, and differential scanning calorimetry. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5169–5179, 2009     

Synthesis of four‐armed poly(ε‐caprolactone)‐block‐poly(ethylene oxide) by diethylzinc catalyst

Biodegradable, amphiphilic, four‐armed poly(?‐caprolactone)‐block‐poly(ethylene oxide) (PCL‐b‐PEO) copolymers were synthesized by ring‐opening polymerization of ethylene oxide in the presence of four‐armed poly(?‐caprolactone) (PCL) with terminal OH groups with diethylzinc (ZnEt₂) as a catalyst. The chemical structure of PCL‐b‐PEO copolymer was confirmed by ¹H NMR and ¹³C NMR. The hydroxyl end groups of the four‐armed PCL were successfully substituted by PEO blocks in the copolymer. The monomodal profile of molecular weight distribution by gel permeation chromatography provided further evidence for the four‐armed architecture of the copolymer. Physicochemical properties of the four‐armed block copolymers differed from their starting four‐armed PCL precursor. The melting points were between those of PCL precursor and linear poly(ethylene glycol). The length of the outer PEO blocks exhibited an obvious effect on the crystallizability of the block copolymer. The degree of swelling of the four‐armed block copolymer increased with PEO length and PEO content. The micelle formation of the four‐armed block copolymer was examined by a fluorescent probe technique, and the existence of the critical micelle concentration (cmc) confirmed the amphiphilic nature of the resulting copolymer. The cmc value increased with increasing PEO length. The absolute cmc values were higher than those for linear amphiphilic block copolymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 950–959, 2004     

Hydrolytic degradation of poly(ε‐caprolactone) with different end groups and poly(ε‐caprolactone‐co‐γ‐butyrolactone): characterization and kinetics of hydrocortisone delivery

Asymmetric telechelic α‐hydroxyl‐ω‐(carboxylic acid)‐poly(ε‐caprolactone) (HA‐PCL), α‐hydroxyl‐ω‐(benzylic ester)‐poly(ε‐caprolactone) (HBz‐PCL), and an asymmetric telechelic copolymer α‐hydroxyl‐ω‐(carboxylic acid)‐poly(ε‐caprolactone‐co‐γ‐butyrolactone) (HA‐PCB) were synthesized by ring‐opening polymerization of ε‐caprolactone (CL). CL and CL/γ‐butyrolactone mixture were used to obtain homopolymers and copolymer respectively at 150°C and 2 hr using ammonium decamolybdate (NH₄) [Mo₁₀O₃₄] (Dec) as a catalyst. Water (HA‐PCL and HA‐PCB) or benzyl alcohol (HBz‐PCL) were used as initiators. The three polylactones reached initial molecular weights between 2000 and 3000 Da measured by proton nuclear magnetic resonance (¹H‐NMR). Compression‐molded polylactone caplets were allowed to degrade in 0.5 M aqueous p‐toluenesulfonic acid at 37°C and monitored up to 60 days for weight loss behavior. Data showed that the copolymer degraded faster than the PCL homopolymers, and that there was no difference in the weight loss behavior between HA‐PCL and HBz‐PCL. Caplets of the three polylactones containing 1% (w/w) hydrocortisone were placed in two different buffer systems, pH 5.0 with citrate buffer and pH 7.4 with phosphate buffer at 37°C, and monitored up to 50 days for their release behavior. The release profiles of hydrocortisone presented two stages. The introduction of a second monomer in the polymer chain significantly increased the release rate, the degradation rate for HA‐PCB being faster than those for HBz‐PCL and HA‐PCL. At the pH studied, only slight differences on the liberation profiles were observed. SEM micrographs indicate that hydrolytic degradation occurred mainly by a surface erosion mechanism. Copyright © 2009 John Wiley & Sons, Ltd.     

Windmill Co4{Co4(μ4‐O)} with 16 Divergent Branches Forming a Family of Metal–Organic Frameworks: Organic Metrics Control Topology,Gas Sorption,and Magnetism

A series of highly connected metal–organic frameworks (MOFs), [Co₈(O)(OH)₄(H₂O)₄(ina)₈](NO₃)₂ ? 2 C₂H₅OH ? 4 H₂O ( 1 ), [Co₈(O)(OH)₄(H₂O)₄(pba)₈](NO₃)₂ ? 8 C₂H₅OH ? 28 H₂O ( 2 ), and [Co₈(O)(OH)₄(H₂O)₄(pbba)₈](NO₃)₂ ? guest ( 3 ), in which ina=isonicotinate, pba=4‐pyridylbenzoate, and pbba=4‐(pyridine‐4‐yl)phenylbenzoate, is reported. These MOFs contain a new secondary building unit (SBU), with a square Co₄(μ₄‐O) central unit having the rare μ₄‐O^2? motif, which is decorated by the other four peripheral cobalt atoms through μ₃‐OH in a windmill‐like shape. This SBU holds 16 divergent connecting organic ligands, pyridyl‐carboxylates, to form three different frameworks. The high porosity of desolvated 2 is shown by the efficient gas absorption of N₂, CO₂, CH₄, and H₂. In addition, 1 and 2 exhibit unusual canted antiferromagnetic behavior with spin‐glass‐like relaxation, with blocking temperatures that are fairly high, 20 K ( 1 ) and 10 K ( 2 ), for cobalt materials. The relationship between the metal clusters and linkers has been studied, in which the size and rotational degrees of freedom of the ligands are found to control the topology, gas sorption, and magnetic properties.     

Microwave‐improved polymerization of ϵ‐caprolactone initiated by carboxylic acids

The ring‐opening polymerization of ε‐caprolactone (ε‐CL), initiated by carboxylic acids such as benzoic acid and chlorinated acetic acids under microwave irradiation, was investigated; with this method, no metal catalyst was necessary. The product was characterized as poly(ε‐caprolactone) (PCL) by ¹H NMR spectroscopy, Fourier transform infrared spectroscopy, ultraviolet spectroscopy, and gel permeation chromatography. The polymerization was significantly improved under microwave irradiation. The weight‐average molecular weight (M_w) of PCL reached 44,800 g/mol, with a polydispersity index [weight‐average molecular weight/number‐average molecular weight (M_w/M_n)] of 1.6, when a mixture of ε‐CL and benzoic acid (25/1 molar ratio) was irradiated at 680 W for 240 min, whereas PCL with M_w = 12,100 and M_w/M_n = 4.2 was obtained from the same mixture by a conventional heating method at 210 °C for 240 min. A degradation of the resultant PCL was observed during microwave polymerization with chlorinated acetic acids as initiators, and this induced a decrease in M_w of PCL. However, the degradation was hindered by benzoic acid at low concentrations. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 13–21, 2003     

Thermal decomposition of hydrotalcite with hexacyanoferrate(II) and hexacyanoferrate(III) anions in the interlayer

The mechanism for the decomposition of hydrotalcite remains unsolved. Controlled rate thermal analysis enables this decomposition pathway to be explored. The thermal decomposition of hydrotalcites with hexacyanoferrate(II) and hexacyanoferrate(III) in the interlayer has been studied using controlled rate thermal analysis technology. X-ray diffraction shows the hydrotalcites have a d(003) spacing of 10.9 and 11.1 Å which compares with a d-spacing of 7.9 and 7.98 Å for the hydrotalcite with carbonate or sulphate in the interlayer. Calculations show dehydration with a total loss of 7 moles of water proving the formula of hexacyanoferrate(II) intercalated hydrotalcite is Mg₆Al₂(OH)₁₆[Fe(CN)₆]_0.5·7H₂O and 9.0 moles for the hexacyanoferrate(III) intercalated hydrotalcite with the formula of Mg₆Al₂(OH)₁₆[Fe(CN)₆]_0.66·9H₂O. CRTA technology indicates the partial collapse of the dehydrated mineral. Dehydroxylation combined with CN unit loss occurs in two isothermal stages at 377 and 390°C for the hexacyanoferrate(III) and in a single isothermal process at 374°C for the hexacyanoferrate(III) hydrotalcite.     

Synthesis of inverse star block copolymer by combination of ATRP,ring opening polymerization,and “click chemistry”

The inverse star block copolymer, (poly(ε‐caprolactone)‐b‐polystyrene)₂‐core‐(poly(ε‐caprolactone)‐b‐polystyrene)₂, [(PCL‐PS)₂‐core‐(PCL‐PS)₂] has been successfully prepared by combination of atom transfer radical polymerization (ATRP), ring opening polymerization (ROP), and “Click Chemistry.” The synthesis includes the following five steps: (1) synthesis of a heterofunctional initiator with two ATRP initiating groups and two hydroxyl groups; (2) formation of (Br‐PS)₂‐core‐(OH)₂ via ATRP of styrene; (3) preparation of the (PCL‐PS)₂‐core‐(OH)₂ through “click” reaction of the α‐propargyl, ω‐acetyl terminated PCL with (N₃‐PS)₂‐core‐(OH)₂ which was prepared by transformation of the terminal bromine groups in (Br‐PS)₂‐core‐(OH)₂ into azide groups; (4) the ROP of CL using (PCL‐PS)₂‐core‐(OH)₂ as macroinitiator to form (PCL‐PS)₂‐core‐(PCL‐OH)₂; and (5) preparation of the (PCL‐PS)₂‐core‐(PCL‐PS)₂ through the ATRP of styrene using (PCL‐PS)₂‐core‐(PCL‐Br)₂ as macroinitiator which was prepared by reaction of the terminal hydroxyl groups at the end of the PCL chains with 2‐bromoisobutyryl bromide. The characterization data support structures of the inverse star block copolymer and the intermediates. The differential scanning calorimeter results and polarized optical microscope observation showed that the intricate structure of the inverse star block copolymer greatly restricted the movement of the PS segments and PCL segments, resulted in the increase of the glass transition temperature of PS segments and the decrease of crystallization ability of PCL segments. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7757–7772, 2008     

A convenient synthesis of α,α′‐ homo‐ and α,α′‐hetero‐bifunctionalized poly(ε‐caprolactone)s by ring opening polymerization: The potentially valuable precursors for miktoarm star copolymers

Two new ring opening polymerization (ROP) initiators, namely, (3‐allyl‐2‐(allyloxy)phenyl)methanol and (3‐allyl‐2‐(prop‐2‐yn‐1‐yloxy)phenyl)methanol each containing two reactive functionalities viz. allyl, allyloxy and allyl, propargyloxy, respectively, were synthesized from 3‐allylsalicyaldehyde as a starting material. Well defined α‐allyl, α′‐allyloxy and α‐allyl, α′‐propargyloxy bifunctionalized poly(ε‐caprolactone)s with molecular weights in the range 4200–9500 and 3600–10,900 g/mol and molecular weight distributions in the range 1.16–1.18 and 1.15–1.16, respectively, were synthesized by ROP of ε‐caprolactone employing these initiators. The presence of α‐allyl, α′‐allyloxy and α‐allyl, α′‐propargyloxy functionalities on poly(ε‐caprolactone)s was confirmed by FT‐IR, ¹H, ¹³C NMR spectroscopy, and MALDI‐TOF analysis. The kinetic study of ROP of ε‐caprolactone with both the initiators revealed the pseudo first order kinetics with respect to ε‐caprolactone consumption and controlled behavior of polymerization reactions. The usefulness of α‐allyl, α′‐allyloxy functionalities on poly(ε‐caprolactone) was demonstrated by performing the thiol‐ene reaction with poly(ethylene glycol) thiol to obtain (mPEG)₂‐PCL miktoarm star copolymer. α‐Allyl, α′‐propargyloxy functionalities on poly(ε‐caprolactone) were utilized in orthogonal reactions i.e copper catalyzed alkyne‐azide click (CuAAC) with azido functionalized poly(N‐isopropylacrylamide) followed by thiol‐ene reaction with poly(ethylene glycol) thiol to synthesize PCL‐PNIPAAm‐mPEG miktoarm star terpolymer. The preliminary characterization of A₂B and ABC miktoarm star copolymers was carried out by ¹H NMR spectroscopy and gel permeation chromatography (GPC). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 844–860     

Synthesis of Dendrigraft Poly(ϵ‐Caprolactone)s Using Side Hydroxyl Groups for the Grafting of Branch Chains

Dendrigraft poly(ϵ‐caprolactone)s with high molecular weight and narrow polydispersity are synthesized via a convenient generation‐growth approach. Copolymerization of ϵ‐caprolactone (CL) and 4‐(2‐benzoxyethoxy)‐ϵ‐caprolactone (BECL) with stannous octanoate as a catalyst affords a functionalized poly(ϵ‐caprolactone) (PCL) with benzyl‐protected hydroxyl side groups. After removal of benzyl groups by palladium‐catalyzed hydrogenolysis, the graft copolymerization of CL and BECL onto the hydroxyl‐bearing linear polyester (zero‐generation) affords the first‐generation graft polyester. Further deprotection and graft polymerization cycles led to dendrigraft polyesters. Molecular weights are multiplied in each graft copolymerization. The second‐generation dendrigraft poly(ϵ‐caprolactone) has an M_w of 236 000 g·mol⁻¹ and M_w/M_n of 1.53.     

Ring‐opening polymerization of ϵ‐caprolactone by iodine charge‐transfer complex

The ring‐opening polymerization of ?‐caprolactone (?‐CL) catalyzed by iodine (I₂) was studied. The formation of a charge‐transfer complex (CTC) among triiodide, I, and ?‐CL was confirmed with ultraviolet–visible spectroscopy. The monomer ?‐CL was polymerized in bulk using I₂ as a catalyst to form the polyester having apparent weight‐average molecular weights of 35,900 and 45,500 at polymerization temperatures of 25 and 70 °C, respectively. The reactivity of both, ?‐CL monomer and ?‐CL:I₂ CTC, was interpreted by means of the potential energy surfaces determined by semiempirical computations (MNDO‐d). The results suggest that the formation of the ?‐CL:I₂ CTC leads to the ring opening of the ?‐CL structure with the lactone protonation and the formation of a highly polarized polymerization precursor (?‐CL)⁺. The band gaps approximated from an extrapolation of the oligomeric polycaprolactone (PCL) structures were computed. With semiempirical quantum chemical calculations, geometries and charge distributions of the protonated polymerization precursor (?‐CL)⁺ were obtained. The calculated band gap (highest occupied molecular orbit/lowest unoccupied molecular orbit differences) agrees with the experiment. The analysis of the oligomeric PCL isosurfaces indicate the existence of a weakly lone pair character of the C?O and C? O bonds suggesting a ?‐CL ring‐opening specificity. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 714–722, 2002     

Supramolecular inclusion complexation of polyhedral oligomeric silsesquioxane capped poly(ε‐caprolactone) with α‐cyclodextrin

Supramolecular inclusion complexes (ICs) involving polyhedral oligomeric silsesquioxane (POSS) capped poly(?‐caprolactone) (PCL) and α‐cyclodextrin (α‐CD) were investigated. POSS‐terminated PCLs with various molecular weights were prepared via the ring‐opening polymerization of ?‐caprolactone (CL) with 3‐hydroxypropylheptaphenyl POSS as an initiator. Because of the presence of the bulky silsesquioxane terminal group, the inclusion complexation between α‐CD and the POSS‐capped PCL was carried out only with a single end of a PCL chain threading inside the cavity of α‐CD, which allowed the evaluation of the effect of the POSS terminal groups on the efficiency of the inclusion complexation. The X‐ray diffraction results indicated that the organic–inorganic ICs had a channel‐type crystalline structure. The stoichiometry of the organic–inorganic ICs was quite dependent on the molecular weights of the POSS‐capped PCLs. With moderate molecular weights of the POSS‐capped PCLs (e.g., M_n =3860 or 9880), the stoichiometry was 1:1 mol/mol (CL unit/α‐CD), which was close to the literature value based on the inclusion complexation of α‐CD with normal linear PCL chains with comparable molecular weights. When the PCL chains were shorter (e.g., for the POSS‐capped PCL of M_n = 1720 or 2490), the efficiency of the inclusion complexation decreased. The decreased efficiency of the inclusion complexation could be attributed to the lower mobility of the bulky POSS group, which restricted the motion of the PCL chain attached to the silsesquioxane cage. This effect was pronounced with the decreasing length of the PCL chains. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1247–1259, 2007     

Novel synthesis of biodegradable amphiphilic linear and star block copolymers based on poly(ε‐caprolactone) and poly(ethylene glycol)

Biodegradable, amphiphilic, diblock poly(ε‐caprolactone)‐block‐poly(ethylene glycol) (PCL‐b‐PEG), triblock poly(ε‐caprolactone)‐block‐poly(ethylene glycol)‐block‐poly(ε‐caprolactone) (PCL‐b‐PEG‐b‐PCL), and star shaped copolymers were synthesized by ring opening polymerization of ε‐caprolactone in the presence of poly(ethylene glycol) methyl ether or poly(ethylene glycol) or star poly(ethylene glycol) and potassium hexamethyldisilazide as a catalyst. Polymerizations were carried out in toluene at room temperature to yield monomodal polymers of controlled molecular weight. The chemical structure of the copolymers was investigated by ¹H and ¹³C NMR. The formation of block copolymers was confirmed by ¹³C NMR and DSC investigations. The effects of copolymer composition and molecular structure on the physical properties were investigated by GPC and DSC. For the same PCL chain length, the materials obtained in the case of linear copolymers are viscous whereas in the case of star copolymer solid materials are obtained with low T_g and T_m temperatures. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3975–3985, 2007     

Microwave‐assisted ring‐opening polymerization of ϵ‐caprolactone

Ring‐opening polymerization of ?‐caprolactone was carried out smoothly and effectively with constant microwave powers of 170, 340, 510, and 680 W, respectively, with a microwave oven at a frequency of 2.45 GHz. The temperature of the polymerization ranged from 80 to 210 °C. Poly(?‐caprolactone) (PCL) with a weight‐average molar mass (M_w) of 124,000 g/mol and yield of 90% was obtained at 680 W for 30 min using 0.1% (mol/mol) stannous octanoate as a catalyst. When the polymerization was catalyzed by 1% (w/w) zinc powder, the M_w of PCL was 92,300 g/mol after the reaction mixture was irradiated at 680 W for 270 min. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1749–1755, 2002     

Synthesis of block and end‐functionalized polyesters by triflimide‐catalyzed ring‐opening polymerization of ε‐caprolactone, 1,5‐dioxepan‐2‐one,and rac‐lactide

The ring‐opening polymerization (ROP) of cyclic esters, such as ε‐caprolactone, 1,5‐dioxepan‐2‐one, and racemic lactide using the combination of 3‐phenyl‐1‐propanol as the initiator and triflimide (HNTf₂) as the catalyst at room temperature with the [monomer]₀/[initiator]₀ ratio of 50/1 was investigated. The polymerizations homogeneously proceeded to afford poly(ε‐caprolactone) (PCL), poly(1,5‐dioxepan‐2‐one) (PDXO), and polylactide (PLA) with controlled molecular weights and narrow polydispersity indices. The molecular weight determined from an ¹H NMR analysis (PCL, M_n,NMR = 5380; PDXO, M_n,NMR = 5820; PLA, M_n,NMR = 6490) showed good agreement with the calculated values. The ¹H NMR and matrix‐assisted laser desorption ionization time‐of‐flight mass spectrometry analyses strongly indicated that the obtained compounds were the desired polyesters. The kinetic measurements confirmed the controlled/living nature for the HNTf₂‐catalyzed ROP of cyclic esters. A series of functional alcohols, such as propargyl alcohol, 6‐azido‐1‐hexanol, N‐(2‐hydroxyethyl)maleimide, 5‐hexen‐1‐ol, and 2‐hydroxyethyl methacrylate, successfully produced end‐functionalized polyesters. In addition, poly(ethylene glycol)‐block‐polyester, poly(δ‐valerolactone)‐block‐poly(ε‐caprolactone), and poly(ε‐caprolactone)‐block‐polylactide were synthesized using the HNTf₂‐catalyzed ROP. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2455–2463     

Synthesis and structural analysis of functionalized poly (ϵ‐caprolactone)‐based three‐arm star polymers

Hydroxyl‐functionalized three‐arm poly(?‐caprolactone)s (PGCL‐OHs) were synthesized by the ring‐opening polymerization of ?‐caprolactone in the presence of glycerol (as the core) and stannous octoate. The effect of the feed ratio of ?‐caprolactone to glycerol on the ring‐opening polymerization was studied. These three‐arm PGCL‐OHs were then converted into double‐bond‐functionalized three‐arm poly(?‐caprolactone)s (PGCL‐Mas) by the reaction of PGCL‐OH with maleic anhydride in the melt at 130 °C. The quantitative conversion of hydroxyl functionality was achieved at a low molecular weight. The resulting PGCL‐OH and PGCL‐Ma were characterized with gel permeation chromatography, Fourier transform infrared, ¹H NMR, ¹³C NMR, and differential scanning calorimetry. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1127–1141, 2002