高硅SSZ-13分子筛膜二次水热生长过程

采用稀释模板剂合成溶胶在管状莫来石支撑体上制备高硅SSZ-13分子筛膜以研究膜的二次水热生长过程。对433 K下二次生长2~72 h的膜和底料进行表征,XRD表明膜和底料中的SSZ-13特征峰均在6 h后出现。底料中的晶粒尺寸基本不随晶化时间的延长而变化。在298 K和0.4 MPa测试条件下,433 K晶化72 h的SSZ-13分子筛膜CO₂渗透通量为2.08×10^-7 mol·m^-2·s^-1·Pa^-1,CO₂/CH₄理想选择性为24。探讨了SSZ-13分子筛膜的生长过程：涂覆在支撑体上的晶种首先溶解并形成大量有序的结构单元,诱导溶胶中晶粒形成并快速生长,晶粒沉积在支撑体的表面共生形成无缺陷的膜层。     

利用适用于SAPO-34的有机结构导向剂合成SSZ-13分子筛

硅铝分子筛SSZ-13和硅磷铝分子筛SAPO-34已广泛应用于已商业化的催化应用中, 如甲醇制烯烃反应(MTO)和氨气选择性催化还原反应(NH₃-SCR). 目前, 已有多种商业化的有机结构导向剂(OSDA)可用于制备 SAPO-34, 而用于合成SSZ-13的OSDA仍主要依赖经典的N,N,N-三甲基-1-金刚烷基氢氧化铵(TMAdaOH). 因此, 寻找具有较高性价比且可导向合成高硅铝比(SAR)SSZ-13的OSDAs具有重要意义. 本文使用3种可制备SAPO-34的OSDAs[二异丙胺(DIPA)、 二丙胺(DPA)、 正丁胺(nBA)]替代部分TMAdaOH, 发现即使不加入晶种也可合成出SSZ-13. 采用粉末X射线衍射(PXRD)和固体核磁共振(ss-NMR)分析方法对制备的SSZ-13进行了系统研究. 结果显示, 所合成的具有可调变SARs的SSZ-13负载Cu之后, 在NH₃-SCR性能上与商业化催化剂相当. 此外, 通过研究DIPA和TMAdaOH合成SSZ-13的晶化机理发现, DIPA的加入可以加快结晶过程、 提高产率并防止非晶相的形成. 本文提出的观点可为寻找更高效和商业化的SSZ-13结构导向剂及合成具有特定性质的SSZ-13提供参考.     

Synthesis Optimization of SSZ-13 Zeolite Membranes by Dual Templates for N2/NO2 Separation

High-silica SSZ-13 zeolite membranes are promising in industrial separations of light gases and continuous membranes are highly demanded for better separation performances. Herein, pure-phase, continuous and thin SSZ-13 zeolite membranes were synthesized using dual templates of N,N,N-trimethtyl-1-adamantammonium hydroxide(TMAdaOH) and tetraethylammonium hydroxide(TEAOH). Systematical investigations of TMAdaOH/TEAOH ratios and their concentrations show that TMAdaOH acts as the main structure-directing agent in the formation of the SSZ-13 zeolite. TMAdaOH cooperatively plays with TEAOH in promoting the SSZ-13 crystal intergrowth to form a continuous polycrystalline membrane. Additionally, appropriate introduction of TEAOH is able to adjust the membrane thickness to the crystal-comparable size of ca. 2.0 μm. The SSZ-13 membranes are further applied for N₂/NO₂separation, which is firstly reported on zeolite membranes. The gas permeation results show that the SSZ-13 membrane synthesized by the dual-template approach exhibits selective separation of N₂ over NO₂ with N₂/NO₂ separation factor of 7.6 and N₂ permeance of 1.66×10^-8 mol·m^-2·s^-1·Pa^-1.     

DFT计算结合固体NMR研究富铝SSZ-13的铝分布和Br?nsted酸性

具有菱沸石(CHA)结构的SSZ-13分子筛在甲醇制烯烃(MTO)及柴油机车尾气氨选择性催化还原(NH_3-SCR)反应中具有重要的应用,采用富铝SSZ-13可以调节MTO反应的烯烃选择性和提升NH_3-SCR的低温脱硝活性,因此SSZ-13中的铝含量和分布与对应的酸性决定了其催化性能。本文采用密度泛函理论结合固体核磁共振实验研究了富铝和富硅HSSZ-13的Al位置与Br?nsted酸强度的内在关系。通过计算取代能发现,对于孤立Al位,质子位于Al周围4个不同O位时能量差异较小,最稳定的B酸位点是O(1)―H。对于富铝SSZ-13,两个Al原子位于同一六元环的对位是Al-Si-Si-Al (NNNN)序列中最稳定的结构,而Al-Si-Al (NNN)序列中能量最优的Al分布是两个铝原子排布于六棱柱上下不同的六元环上。通过计算最稳定构型下的质子亲和势、NH3脱附能和吸附氘代乙腈后的1H NMR化学位移,发现富铝SSZ-13中含有Si(2Al)分布的NNN序列导致了其Br?nsted酸强度弱于高硅的分子筛。分峰拟合29Si魔角旋转核磁共振(MASNMR)谱图表明富铝SSZ-13中Si(2Al)的含量在43%以上,而吸附氘代乙腈后的1H MAS NMR实验显示富铝SSZ-13的桥羟基化学位移向低场移动,进一步证明富铝SSZ-13具有较弱的Br?nsted酸强度。     

碳化硅上生长Cu/SSZ-13分子筛及其NH3-SCR催化性能

汽车尾气和柴油不完全燃烧所释放的NOx严重污染了大气环境.为了降低对大气的污染,可将其催化还原成氮气.氨气选择性催化还原(NH3-SCR)是使用较广泛的机动车高效脱硝技术.用于催化脱硝反应的催化剂有多种类型,分子筛具有特殊的孔道结构和骨架结构及高比表面积,因而已广泛用作脱硝反应催化剂.与传统三效催化剂相比,分子筛催化剂总体表现出更好的脱硝催化活性,但在高温下不稳定,容易失活,不耐热冲击,水热稳定性差.SiC具有耐酸碱、耐腐蚀、抗氧化、耐磨及良好的热稳定性和导电性,因此作为催化剂载体近年来引起广泛关注.但是其本身也存在许多缺点,如比表面积低、表面性质不活泼、不利于金属物种分散等.因此,本文通过原位水热法将SSZ-13生长在SiC表面,制备出新型催化复合材料SSZ-13@SiC.采用X射线衍射(XRD)、扫描电子显微镜(SEM)和N2吸附-脱附等手段研究了不同碱量和晶化时间对SSZ-13在SiC表面生长的影响,负载Cu后获得Cu/SSZ-13@SiC作为催化剂,研究了SiC对Cu/SSZ-13中高温下脱硝活性的影响规律.结果表明,碱含量会影响SSZ-13在SiC表面的结晶程度.当SiO2/NaOH ≥ 0.1时,SSZ-13有杂相出现,并且结晶度都不高; 当SiO2/NaOH < 0.1时,SiC表面会生长成纯相的SSZ-13晶粒且具有较高的结晶度.晶化时间也会影响SSZ-13在SiC表面的覆盖程度: 反应1 d时,SiC表面会生长零星的SSZ-13晶粒; 2 d时,SSZ-13达到全面覆盖; 3 d后,SSZ-13在SiC上的生长达到饱和,其比表面积达到最大值,约为201.3 m2/g.通过离子交换将不同含量Cu离子交换到分子筛表面,其中Cu(1.71)/SSZ-13@SiC样品具有最佳的脱硝活性,接近200 °C时,NO转化率就达到90%以上,到高温500 °C时,NO转化率仍能保持在70%以上.相比于未负载的Cu/SSZ-13,Cu/SSZ-13@SiC催化剂在NH3-SCR测试中具有更高的高温催化活性,同时催化活性窗口明显拓宽.上述结果说明SiC对Cu/SSZ-13的高温催化活性具有一定的提高和稳定作用.     

Mechanochemical Pretreatment for Efficient Solvent-Free Synthesis of SSZ-13 Zeolite

The economical and environmentally benign synthesis of SSZ-13 zeolite was possible due to the mechanochemical activation of dry reagents by planetary mill. Contrary to manual grinding in a mortar, the proposed automatized approach is scalable and reproducible. This solvent-free process provided a huge gain in product/gel ratios, significantly minimized reaction space and organic structure-directing agent use, and allowed for the elimination of agitation. Obtained materials were comparable to the product of “classical” syntheses. The use of different silica sources resulted in SSZ-13 zeolites with various characteristics: different Si/Al ratio and crystal size.     

SSZ-13和RUB-50分子筛上甲醇制烯烃的对比研究

对比研究了SSZ-13(CHA拓扑结构)和RUB-50(LEV拓扑结构)硅铝分子筛笼大小对甲醇制烯烃反应性能的影响,并采用X射线衍射、N2吸附-脱附、固体核磁共振、热重和紫外-可见光谱等技术对催化剂的结构及反应后的碳物种进行了表征.结果表明,笼尺寸较大的SSZ-13分子筛在反应中的稳定性和产物丙烯选择性均较高;而笼尺寸...     

Conversion of CO_2 and H_2 into propane over InZrO_x and SSZ-13 composite catalyst

Direct converting carbon dioxide into hydrocarbon fuels and value-added chemicals would offer a very attractive approach for efficient utilization of CO₂ as a carbon resource.Although,olefins,aromatics and gasoline have been successfully synthesized by CO₂ hydrogenation,highly selective conversion of CO₂ and H₂ into C₂₊hydrocarbon is still challenging due to a high C-C coupling barrier and inhibiting the production of other long-chain hydrocarbons.Here,we report a composite catalyst made of InZrO_x and SSZ-13 molecular sieve(InZrO_x+SSZ-13),which exhibits 74.5% propane selectivity at 623 K.The 8-MR micropores and the higher strength of the acid for SSZ-13 benefit the formation of propane.Compared with pure InO_x and m-ZrO₂ the composite oxide InZrO_x containing more oxygen vacancies,exhibits to be more readily reduced by H₂ and easier to adsorb and desorb CO₂ within the reaction temperature.All those could be beneficial to the activation and conversion of H₂ and CO₂.The catalytic performance of InZrO_x+SSZ-13 in CO₂ hydrogenation provides a potential for production of propane.     

使用四乙基氢氧化铵作为有机模板剂和常规硅铝源直接合成SSZ-13沸石分子筛

使用四乙基氢氧化铵作为有机模板剂, 利用常规铝源和硅源而不需要高硅Y沸石作为起始原料, 同时加入适量的沸石晶种直接合成了SSZ-13沸石分子筛. 所合成的沸石产物结晶度好, 具有良好的水热稳定性, 并在氨选择性催化还原(NH₃-SCR)反应中显示出优异的催化性能, 为其在工业上广泛应用提供了可能.     

Unconventional, highly selective CO2 adsorption in zeolite SSZ-13

Low-pressure adsorption of carbon dioxide and nitrogen was studied in both acidic and copper-exchanged forms of SSZ-13, a zeolite containing an 8-ring window. Under ideal conditions for industrial separations of CO(2) from N(2), the ideal adsorbed solution theory selectivity is >70 in each compound. For low gas coverage, the isosteric heat of adsorption for CO(2) was found to be 33.1 and 34.0 kJ/mol for Cu- and H-SSZ-13, respectively. From in situ neutron powder diffraction measurements, we ascribe the CO(2) over N(2) selectivity to differences in binding sites for the two gases, where the primary CO(2) binding site is located in the center of the 8-membered-ring pore window. This CO(2) binding mode, which has important implications for use of zeolites in separations, has not been observed before and is rationalized and discussed relative to the high selectivity for CO(2) over N(2) in SSZ-13 and other zeolites containing 8-ring windows.     

Dual template synthesis of a highly mesoporous SSZ-13 zeolite with improved stability in the methanol-to-olefins reaction

The dual template synthesis of zeolite SSZ-13 by use of trimethyl-adamantanammonium hydroxide and a diquaternary-ammonium mesoporogen induces considerable mesoporosity without impeding zeolite microporosity. The strongly improved accessibility of Br?nsted sites in mesoporous SSZ-13 increases its stability during application as an acid catalyst in the methanol-to-olefins reaction.     

SSZ-53 and SSZ-59: two novel extra-large pore zeolites

The syntheses, structure solutions, and physicochemical and catalytic characterizations of the novel zeolites SSZ-53 and SSZ-59 are described. SSZ-53 and SSZ-59 were synthesized under hydrothermal conditions with the [1-(4-fluorophenyl)cyclopentylmethyl]trimethyl ammonium cation and 1-[1-(4-chlorophenyl)cyclopentylmethyl]-1-methyl azocanium cation, respectively, as structure-directing agents. The framework topology of SSZ-53 was solved with the FOCUS method, and the structure of SSZ-59 was determined by model building. Rietveld refinement of synchrotron X-ray powder diffraction data confirms each proposed model. SSZ-53 and SSZ-59 each possess a one-dimensional channel system delimited by 14-membered rings. Results from transmission electron microscopy, electron diffraction, catalytic experiments (spaciousness index and constraint index tests), and argon and hydrocarbon adsorption experiments are consistent with the proposed structures.     

Evaluation of Co/SSZ-13 Zeolite Catalysts Prepared by Solid-Phase Reaction for NO-SCR by Methane

Co/SSZ-13 zeolites were prepared by heating the finely dispersed mixture of NH₄-SSZ-13 and different cobalt salts up to 550 °C. Investigations by thermogravimetry – differential scanning calorimetry – mass spectrometry provided new insight into details of the solid-state reaction. Formation of Co carrying hydrate melt or volatile species was shown to proceed from chloride, nitrate, or acetylacetonate Co precursor salts upon thermal treatment. This phase change allows the transport of the Co species into the zeolite pores. The reaction of the NH₄⁺ or H⁺ zeolite cations and the mobile Co precursors generates vapor or gas products, readily leaving the zeolite pores, and cobalt ions in lattice positions suggesting that solid-state ion-exchange is the prevailing process. The obtained catalysts are of good activity and N₂ selectivity in the CH₄/NO-SCR reaction. The thermal treatment of acetate or formate salts give solid intermediates that are unable to get in contact and react with the cations in the zeolite micropores. These catalysts contain mainly Co-oxide clusters located on the outer surface of the zeolite crystallites and have poor catalytic performance.     

SSZ-39分子筛的合成及应用进展

近年来,小孔八元环SSZ-39分子筛因具有特殊的孔道结构和物理化学性质,在小分子择形催化反应中展现出相对优异的催化活性、抗积碳性和水热稳定性.本文概述了SSZ-39分子筛的合成历程,包括不同种类有机模板剂的使用、特定硅源铝源的选择以及凝胶组成的调控等;简要总结了SSZ-39分子筛在甲醇制低碳烯烃、氮氧化物的选择性催化还...     

以四乙基氢氧化铵为模板并通过转晶法合成高硅铝比的SSZ⁃13沸石分子筛

使用四乙基氢氧化铵为有机模板剂,以低硅铝比(nSiO2/nAl2O3)的Y分子筛为铝源,通过转晶法制备结晶度良好的SSZ?13沸石分子筛。从凝胶配比方面考察了不同原料组成对分子筛合成的影响,并通过X射线衍射(XRD)、扫描电子显微镜(SEM)及电感耦合等离子体(ICP)表征水热反应过程中的物相、形貌、硅铝比等变化,揭示分子筛合成过程。氨选择性催化还原(NH3?SCR)反应显示该分子筛具有优异的催化活性,为其工业上的广泛应用提供了可能性。     

SSZ-60: a new large-pore zeolite related to ZSM-23

SSZ-60 is a new borosilicate zeolite that may be prepared using N-ethyl-N-(2,4,4-trimethylcyclopentyl)pyrrolidinium or N-ethyl-N-(3,3,5-trimethylcyclohexyl)pyrrolidinium as a structure directing agent; the framework of SSZ-60 was determined by the FOCUS Fourier recycling method, its structure refined in space group P21nm and found to possess a one-dimensional channel system with pores delimited by twelve-rings; the topological structure of SSZ-60 may be derived from a sigma-expansion of the framework of ZSM-23 (MTT).     

Studies of the synthesis of SSZ-25 zeolite in a "mixed-template" system

The synthesis of aluminosilicate zeolite, SSZ-25, is described using a two-component organic guest molecule strategy. This method has been recently described by us and is quite effective in crystallizing a variety of aluminosilicate zeolites with reduction in template cost. In this instance the original organic guest component used in the discovery of SSZ-25, N',N',N'-trimethyl-2-adamantammonium cation, is used in conjunction with a variety of smaller amines. The amine is the major organic component in the synthesis and the quaternary ammonium compound, while a minor component, is essential for structure direction to the desired zeolite product. Studies here show that the adamantyl component is preferentially taken up during crystal growth. Our studies showed that the use of the multi-organic component approach to synthesis resulted in a faster and cheaper route to crystallizing SSZ-25. The SSZ-25 has been described in the literature as having the MWW topology and as such has two different channel systems accessed by 10-ring openings; the channel systems do not intersect. One set of 10-rings open into large cavities. In this study we used NMR spectroscopy to examine the as-made materials and to see if the two organic components are used in different capacities in the synthesis, probing if the admantyl component is only found in these larger cavities. The crystalline products could be affected by solvent extraction with polar solvents like dimethylformamide: the X-ray powder patterns and elemental analyses changed with solvent treatment. The solvent-treated crystals were studied by NMR spectroscopy, elemental analysis, and argon adsorption. The two-component organic guest approach was also found to be quite flexible not only with regard to the amine, but also towards the quaternary ammonium compounds. Non-adamantyl polycyclic templates could be used, and polar but non-quaternized adamantyl derivatives also succeeded in directing towards SSZ-25 formation. On the other hand. in one instance it was shown that the two-component approach favors SSZ-25 as the kinetic product but at longer run times Ostwald ripening was observed, leading to the disappearance of SSZ-25 and formation of ferrierite zeolite and quartz.     

Structure and synthesis of SSZ-63: toward an ordered form of zeolite beta

The synthesis, characterization, and structure elucidation of the borosilicate zeolite SSZ-63 are described. SSZ-63 is synthesized using the 1-cyclodecyl-1-methylpyrrolidinium cation as a structure-directing agent. The structural model for SSZ-63 was determined by comparison of its powder X-ray diffraction pattern with those of zeolite beta and its polytype structures. Whereas conventional zeolite beta may be described as a random intergrowth of polytypes A and B, SSZ-63 is more accurately described as a random intergrowth of polytypes B and C(H) (the hypothetical polytype C proposed by Higgins). Polytype C(H) is essentially an ordered intergrowth (of polytypes A and B) in which one of the crystallographic projections is equivalent to those in polytype A and another projection is equivalent to those in polytype B. Unlike zeolite beta, which possesses significant disorder related to layer shifts along both the a- and b-crystallographic axes, the structure of SSZ-63 has little disorder associated with the translations of layers in the a-direction. DIFFaX simulations of the powder diffraction patterns, electron diffraction, and high-resolution transmission electron microsocopy data all support the proposed model.     

Polymethylated [4.1.1] Octanes Leading to Zeolite SSZ-50

In this communication, we report on the discovery of novel zeolite compositions, SSZ-50. The zeolite has the RTH topology but can be made over a large silica-to-alumina range including no aluminum at all. The surprising capability to produce a broad compositional range comes from the use of a single organo-cation guest molecule in the zeolite synthesis. The molecule is a specific derivative from within a family of 2-aza [4.1.1] bicyclo octanes that were prepared employing a sequence of organic synthesis steps from a starting ketone. Other cage-based zeolites like SSZ-35,-36,-39 and MTN arose from the use of the other derivatives in this series. We also comment on the tendency of a variety of polymethylated organo-cations to produce RTH, the closely related ITE, or the intergrowth structure, SSZ-36.     

Effect of Calcination Temperature on the Properties of Mn–Zr–Ce Catalysts in the Oxidation of Carbon Monoxide

Kinetics and Catalysis - The effect of the calcination temperature of MnOх–ZrO2–CeO2 catalysts on their structural properties and activity in the reaction of CO oxidation has been...