Breaking 12% efficiency in flexible organic solar cells by using a composite electrode

The performance of flexible organic solar cells(OSCs)significantly relies on the quality of transparent flexible electrode.Here,we used silver nanowires(AgNWs)with various weight ratios to dope high-conductive poly(3,4-ethylenedioxythiophene):polystyrene sulfonate(PH1000)to optimize the optical and electronic properties of PH1000 film.A high-quality flexible composite electrode PET/Ag-mesh/PH1000:AgNWs-20 with smooth surface,a low sheet resistance of 6Ω/sq and a high transmittance of 86%at 550-nm wavelength was obtained by doping 20 wt%AgNWs to PH1000(PH1000:AgNWs-20).The flexible OSCs based on the PET/Ag-mesh/PH1000:AgNWs-20 electrode delivered a power conversion efficiency(PCE)of12.07%with an open circuit voltage(V_(oc))of 0.826 V,a short-circuit current density(J_(sc))of 20.90 m A/cm~2and a fill factor(FF)of69.87%,which is the highest reported PCE for the flexible indium-tin oxide(ITO)-free OSCs.This work demonstrated that the flexible composite electrodes of PET/Ag-mesh/PH1000:AgNWs are promising alternatives for the conventional PET/ITO electrode,and open a new avenue for developing high-performance flexible transparent electrode for optoelectronic devices.     

Flexible ITO-free organic solar cells over 10% by employing drop-coated conductive PEDOT:PSS transparent anodes

Highly conductive poly(3,4-ethylenedioxythiophene):poly(styrene-sulfonic acid)(PEDOT:PSS) has been explored to fabricate flexible and stretchable conductors. Generally, PEDOT:PSS transparent anodes are prepared by spin-coating method. In this article, we adopt a method by dropping PEDOT:PSS aqueous solution on the PET plastic substrate to fabricate flexible electrodes. Compared with spin coating, drop-coating is simple and cost-effective with large-area fabrications. Through this method, we fabricated highly transparent conductive electrodes and systematically studied their electrical, optical, morphological and mechanical properties. With dimethyl sulfoxide/methanesulfonic acid(DMSO/MSA) treated PEDOT:PSS electrode,bendable devices based on non-fullerene system displayed an open-circuit voltage of 0.925 V, a fill factor of 70.74%, and a high power conversion efficiency(PCE) of 10.23% under 100 mW cm~(-2) illumination, which retained over 80% of the initial PCE value after 1000 bending cycles. Based on the findings, drop-coated PEDOT:PSS electrodes exhibited high suitability for the development of large-area and high-efficiency printed solar cell modules in the future.     

基于银纳米线复合透明电极的可弯折柔性聚合物太阳能电池

本文设计了一种可以通过刮涂方法制备的基于银纳米线(AgNWs)的柔性复合透明电极,并以此为基础实现了高性能柔性聚合物太阳能电池的制备。 基于银纳米线的柔性复合薄膜(APA)由银纳米线(AgNWs),聚乙烯醇缩丁醛(PVB)和铝掺杂氧化锌(AZO)纳米粒子在低温下通过多层刮涂的方法制备。 APA透明复合薄膜在550 nm处透光率达到90.90%,面电阻低至13.01 Ω/sq,在柔性基底上具有很高的粘附性。 在透明的APA/聚对苯二甲酸乙二醇酯(PET)基底上制备的柔性聚合物太阳能电池(PSCs),能量转换效率达到5.47%。 而且以5 mm为曲率半径,经过1000次循环弯曲实验,电池的能量转换效率仅下降了14%。     

Inspired by Grape Seed and Wine: Tannic Acid as a Modified Coating for Fabricating Highly Flexible,Transparent and Conductive Film

The application of transparent conductive films in flexible electronics has shown promising prospects recently. Tannic acid(TA) was successfully applied to modifying the surface of polydimethylsiloxane(PDMS) to fhbricate highly flexible, transparent and conductive Ag nanowires(NWs) based films. TA modification transformed the PDMS surface from hydrophobicity into hydrophilicity without decreasing the transparence. A sheet resistance(Rs) of 80 Ω/cm^2 with an optical transmittance of 94% was achieved, which was superior to that of indium tin oxide(ITO) films. More importantly, the TA layer enhanced the interaction between Ag NWs and the PDMS substrate. The Ag NWs films on TA modified PDMS substrate exhibited excellent stability in Rs when subjected to a bending test.     

喷墨打印技术制备聚合物太阳能电池的研究进展

聚合物太阳能电池具有成本低、质量轻、容易制备大尺寸器件等优势,是太阳能电池研究中最为活跃的领域之一。喷墨打印技术作为新的成膜技术,具有材料利用率高、快速、可柔性加工等优点,已被用于聚合物太阳能电池的制备,发展潜力巨大。综述了聚合物太阳能电池、喷墨打印技术和喷墨打印技术制备聚合物太阳能电池的研究进展,同时对聚合物太阳能电...     

Printable SnO2 cathode interlayer with up to 500 nm thickness-tolerance for high-performance and large-area organic solar cells

The printable electrode interlayer with excellent thickness tolerance is crucial for mass production of organic solar cells(OSCs)by solution-based print techniques. Herein, high-quality printable SnO_2 films are simply fabricated by spin-coating or bladecoating the chemical precipitated SnO_2 colloid precursor with post thermal annealing treatment. The SnO_2 films possess outstanding optical and electrical properties, especially extreme thickness-insensitivity. The interfacial electron trap density of SnO_2 cathode interlayers(CILs) are very low and show negligible increase as the thicknesses increase from 10 to 160 nm,resulting in slight change of the power conversion efficiencies(PCEs) of the PM6:Y6 based OSCs from 16.10% to 13.07%. For blade-coated SnO_2 CIL, the PCE remains high up to 12.08% even the thickness of SnO_2 CIL is high up to 530 nm. More strikingly, the large-area OSCs of 100 mm~2 with printed SnO_2 CILs obtain a high efficiency of 12.74%. To the best of our knowledge, this work presents the first example for the high-performance and large-area OSCs with the thickness-insensitive SnO_2 CIL.     

Conductivity enhancement of PEDOT:PSS film via sulfonic acid modification: application as transparent electrode for ITO-free polymer solar cells

3-Hydroxy-1-propanesulfonic acid(HPSA)was applied as a modification layer on poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate)(PEDOT:PSS)film via spin-coating,resulting in a massive boost of the conductivity of PEDOT:PSS film,and thus the as-formed PEDOT:PSS/HPSA bilayer film was successfully used as a transparent electrode for ITO-free polymer solar cells(PSCs).Under the optimized concentration of HPSA(0.2 mol L~(-1)),the PEDOT:PSS/HPSA bilayer film has a conductivity of 1020 S cm~(-1),which is improved by about 1400 times of the pristine PEDOT:PSS film(0.7 S cm~(-1)).The sheet resistance of the PEDOT:PSS/HPSA bilayer film was 98Ωsq~(-1),and its transparency in the visible range was over 80%.Both parameters are comparable to those of ITO,enabling its suitability as the transparent electrode.According to atomic force microscopy(AFM),UV-Vis and Raman spectroscopic measurements,the conductivity enhancement was resulted from the removal of PSS moiety by methanol solvent and HPSA-induced segregation of insulating PSS chains along with the conformation transition of the conductive PEDOT chains within PEDOT:PSS.Upon applying PEDOT:PSS/HPSA bilayer film as the transparent electrode substituting ITO,the ITO-free polymer solar cells(PSCs)based on poly[N-9″-hepta-decanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)]:[6,6]-phenyl C71-butyric acid methyl ester(PC_(71)BM)(PCDTBT:PC_(71)BM)active layer exhibited a power conversion efficiency(PCE)of 5.52%,which is comparable to that of the traditional ITO-based devices.     

基于印刷电子的透明导电薄膜研究进展

透明导电薄膜是一种在可见光范围内透光率较高、导电性优良的薄膜材料.近年来随着智能手机、平板电脑等电子产品日益普及,透明导电薄膜受到越来越多的关注.本文分析了目前占据市场统治地位的掺锡氧化铟透明导电薄膜的缺点以及近年来国内外对透明导电薄膜开展的研究工作,总结了目前在印刷电子领域透明导电薄膜的主要研究方向,一方面是在传统金属氧化物薄膜基础上的改进;另一方面是寻找新型透明导电薄膜材料,并分别综述了各个研究方向的最新进展.     

Fast printing of thin,large area,ITO free electrochromics on flexible barrier foil

Processing of large area, indium tin oxide (ITO) free electrochromic (EC) devices has been carried out using roll‐to‐roll (R2R) processing. By use of very fine high‐conductive silver grids with a hexagonal structure, it is possible to achieve good transparency of the electrode covered substrates and when used in EC devices switching times are similar to corresponding ITO devices. This is obtained without the uneven switching of larger areas, which is generally observed when using ITO because of its high‐sheet resistance. The silver electrode structures for 18 × 18 cm² devices can be processed at high speed (10 m/min) on PET by flexographic printing and the EC polymer ECP‐Magenta as well as a minimal color changing polymer MCCP by slot‐die coating, showing the potential for fast fabrication of large volumes of low‐priced flexible EC devices by use of R2R processing techniques. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Transparent electrodes fabricated via the self-assembly of silver nanowires using a bubble template

To shore up the demand of transparent electrodes for wide applications such as organic light emitting diodes and solar cells, transparent electrodes are required as an alternative for indium tin oxide electrodes. Herein the self-assembly method with a bubble template paves the way for cost-effective fabrication of transparent electrodes with high conductivity and transparency using self-assembly of silver nanowires (AgNWs) in a bubble template. AgNWs were first dispersed in water that was bubbled with a surfactant and a thickening agent. Furthermore, these AgNWs were assembled by lining along the bubble ridges. When the bubbles containing the AgNWs were sandwiched between two glass substrates, the bubble ridges including the AgNWs formed continuous polygonal structures. Mesh structures were formed on both glass substrates after air-drying. The mesh structures evolved into mesh transparent electrodes following heat-treatment. The AgNW mesh structure exhibited a low sheet resistance of 6.2 Ω/square with a transparency of 84% after heat treatment at 200 °C for 20 min. The performance is higher than that of transparent electrodes with random networks of AgNWs. Furthermore, the conductivity and transparency of the mesh transparent electrodes can be adjusted by changing the amount of the AgNW suspension and the space between the two glass substrates.     

Direct Toner Printing: A Versatile Technology for Easy Fabrication of Flexible Miniaturized Electrodes

We reported here three simple, low cost and easy to accomplish strategies for the fabrication of microelectrodes and other conductive patterns using ordinary office laser‐printers. In this work, toner patterns were directly printed onto the flexible substrate, acting as a mask to create the intended conductive design. To highlight the versatility of such technology, toner‐printed patterns were employed in two diverse ways: one in which the patterned toner had the exact design of the electrode and other employing a reverse toner‐printed pattern. The first one was used for the adaptation of the well‐known printed circuit board (PCB) fabrication technique, but using direct toner printing (DTP) in an already conductive flexible substrate. The second was employed for the two remaining strategies: one based on the deposition of conductive film, followed by lift‐off process; and another based on drop‐casting of a conductive ink into the formed toner cavities, followed by thermal cure. As proof‐of‐concept, all three DTP strategies were used for the fabrication of miniaturized gold electrodes in polyimide substrate, and electrochemical performance of each obtained electrode was evaluated by cyclic voltammetry. Insights about DTP technology, alignment issues, advantages, limitations and resolution of each presented approach were provided. Finally, direct toner printing showed to be a simple, affordable and quite promising technology for the fabrication of low cost point‐of‐care electrochemical devices using flexible platforms.     

High-efficiency (7.2%) flexible dye-sensitized solar cells with Ti-metal substrate for nanocrystalline-TiO2 photoanode

High-efficiency flexible dye-sensitized solar cells were fabricated with a Ti-metal foil substrate for photo anode and using a Pt-electrodeposited counter electrode on ITO/polyethylene naphthalate (ITO/PEN); these devices were characterized by incident photon-to-current efficiency (IPCE), optical transmittance and electrical impedance spectroscopy.     

Low reflectivity and high flexibility of tin-doped indium oxide nanofiber transparent electrodes

Tin-doped indium oxide (ITO) has found widespread use in solar cells, displays, and touch screens as a transparent electrode; however, two major problems with ITO remain: high reflectivity (up to 10%) and insufficient flexibility. Together, these problems severely limit the applications of ITO films for future optoelectronic devices. In this communication, we report the fabrication of ITO nanofiber network transparent electrodes. The nanofiber networks show optical reflectivity as low as 5% and high flexibility; the nanofiber networks can be bent to a radius of 2 mm with negligible changes in the sheet resistance.     

A two-step method combining electrodepositing and spin-coating for solar cell processing

Electrochemistry provides a simple and promising method for preparing organic solar cells (OSCs). In this paper, we present a two-step solution-based method to prepare bilayer heterojunction OSCs by electrodepositing polythiophene (PTh) and then spin-coating chloroform solution of [6,6]-phenyl C61-butyric acid methyl ester (PCBM) onto the PTh layer. The influence of film thickness on performance of bilayer solar cells was investigated, and the best performance was achieved when the thickness of PTh and PCBM was 15 nm and 30 nm, respectively. The optimized solar cell showed power conversion efficiency of 0.1% under the illumination of AM 1.5 (100 mW cm⁻²) simulated solar light. This solution-based method offers a new way for processing bilayer OSCs.     

A Facile Solution-Phase Approach to Transparent and Conducting ITO Nanocrystal Assemblies

Monodisperse 11 nm indium tin oxide (ITO) nanocrystals (NCs) were synthesized by thermal decomposition of indium acetylacetonate, In(acac)(3), and tin bis(acetylacetonate)dichloride, Sn(acac)(2)Cl(2), at 270 °C in 1-octadecene with oleylamine and oleic acid as surfactants. Dispersed in hexane, these ITO NCs were spin-cast on centimeter-wide glass substrates, forming uniform ITO NC assemblies with root-mean-square roughness of 2.9 nm. The assembly thickness was controlled by ITO NC concentrations in hexane and rotation speeds of the spin coater. Via controlled thermal annealing at 300 °C for 6 h under Ar and 5% H(2), the ITO NC assemblies became conductive and transparent with the 146 nm-thick assembly showing 5.2 × 10(-3) Ω·cm (R(s) = 356 Ω/sq) resistivity and 93% transparency in the visible spectral range-the best values ever reported for ITO NC assemblies prepared from solution phase processes. The stable hexane dispersion of ITO NCs was also readily spin-cast on polyimide (T(g) ～360 °C), and the resultant ITO assembly exhibited a comparable conductivity and transparency to the assembly on a glass substrate. The reported synthesis and assembly provide a promising solution to the fabrication of transparent and conducting ITO NCs on flexible substrates for optoelectronic applications.     

Influence of the substrate type on the microstructural,optical and electrical properties of sol–gel ITO films

Indium tin oxide (ITO) is recognized as the best transparent and conductive material [transparent conducting oxide (TCO)] until now and its properties are dependent on the preparation method. In the present work ITO films with In:Sn atomic ratio 9:1 were prepared by a sol–gel route on different substrates (microscope glass slides, microscope glass covered with one layer of SiO₂ and Si wafers) for TCO applications. The multilayer ITO films were obtained by successive deposition by the dip-coating method and the films were characterized from the structural, morphological, optical, and electrical points of view using X-ray diffraction, scanning electron microscopy, atomic force microscopy, spectroscopic ellipsometry and by Hall effect measurements, respectively. The results showed that the thickness, optical constants and carrier numbers depend strongly on the type of substrate, number of deposited layers and sol concentration. The optical properties of ITO films are closely related to their electrical properties. The enhancement of the conductivity was possible with the increase of crystallite size (which occurred after thermal treatment) and with the reduction of surface roughness.     

Self-assembling ensembles of silicomolybdic acid-diamines

Modification of the surface of the conductive glass [conductive layer is indium-tin oxide (ITO)] by diamines (1,8-diaminooctane and piperazine) and organic polycations [poly(diallyldimethylammonium chloride) and poly(allylamine) hydrochloride] followed by the formation of electroactive composites with silicomolybdic acid H₄SiMo₁₂O₄₀ was carried out. The two-layer ITO/cationic/anionic coatings were shown to differ by the shape of cyclic voltammograms depending on the cationic component.     

Printing graphene-carbon nanotube-ionic liquid gel on graphene paper: Towards flexible electrodes with efficient loading of PtAu alloy nanoparticles for electrochemical sensing of blood glucose

The increasing demands for portable, wearable, and implantable sensing devices have stimulated growing interest in innovative electrode materials. In this work, we have demonstrated that printing a conductive ink formulated by blending three-dimensional (3D) porous graphene–carbon nanotube (CNT) assembly with ionic liquid (IL) on two-dimensional (2D) graphene paper (GP), leads to a freestanding GP supported graphene–CNT–IL nanocomposite (graphene–CNT–IL/GP). The incorporation of highly conductive CNTs into graphene assembly effectively increases its surface area and improves its electrical and mechanical properties. The graphene–CNT–IL/GP, as freestanding and flexible substrates, allows for efficient loading of PtAu alloy nanoparticles by means of ultrasonic-electrochemical deposition. Owing to the synergistic effect of PtAu alloy nanoparticles, 3D porous graphene–CNT scaffold, IL binder and 2D flexible GP substrate, the resultant lightweight nanohybrid paper electrode exhibits excellent sensing performances in nonenzymatic electrochemical detection of glucose in terms of sensitivity, selectivity, reproducibility and mechanical properties.     

Impact of A–D–A-Structured Dithienosilole- and Phenoxazine-Based Small Molecular Material for Bulk Heterojunction and Dopant-Free Perovskite Solar Cells

Herein, the synthesis of the novel acceptor–donor–acceptor (A–D–A)-structured small molecule Si-PO-2CN based on dithienosilole (DTS) as building block flanked by electron-rich phenoxazine (POZ) units, which are terminated with dicyanovinylene, is presented. Si-PO-2CN showed unique electrochemical and photophysical properties and has been successfully employed in perovskite solar cells (PSCs) as well as in bulk heterojunction organic solar cells (OSCs). The PSCs fabricated with dopant-free Si-PO-2CN as hole-transport material (HTM) exhibited a power conversion efficiency (PCE) of 14.1 % (active area=1.02 cm²). Additionally, a PCE of 5.6 % has been achieved for OSCs, which employed Si-PO-2CN as p-type donor material when blended with a [6,6]-phenyl C71 butyric acid methyl ester (PC₇₁BM) acceptor. The versatile application of Si-PO-2CN provides a pathway for further implementation of DTS-based building blocks in solar cells for designing new molecules.     

Polymer‐coated Boron Doped Diamond Optically Transparent Electrodes for Spectroelectrochemical Sensors

Spectroelectrochemical sensors combine electrochemistry, spectroscopy, and partitioning into a film to provide improved selectivity for the target analyte. The sensor usually consists of an optically transparent electrode (OTE) coated with a charge selective polymer film. The polymer film is chosen to pre‐concentrate analyte at the OTE surface to improve the sensitivity and provide selectivity against like charged interferences. OTEs such as Indium Tin Oxide (ITO) have been used extensively for spectroelectrochemical sensors, but little is known about the applicability of such sensors using other OTE materials, such as Boron Doped Diamond (BDD). One distinct advantage of BDD OTEs over ITO OTEs is their significant increase in sensitivity for organic compounds, such as 4‐aminophenol and hydroquinone. We have developed absorption and fluorescence‐based sensing methods with a BDD OTE coated with a sulfonated ionomer film, Nafion. This is demonstrated with tris(2,2′‐bipyridyl)ruthenium(II) ion [Ru(bpy)₃²⁺] using an attenuated total reflectance (ATR) flow cell setup for both absorption and fluorescence. With a Nafion coated BDD optically transparent thin layer electrode (OTTLE), we developed a fluorescence based sensor for a common polyaromatic hydrocarbon (PAH), 1‐hydroxypyrene (1‐pyOH), achieving a detection limit of 80 nM (17 ppb). This work manifests new sensing applications while broadening the use of spectroelectrochemistry, OTEs, and BDD as an electrode material.