TiO2/SiO2的制备及其对染料X-3B溶液降解的光催化活性

 以粗孔球形硅胶为载体,以聚乙二醇和二乙醇单乙醚的钛酸四丁酯无水乙醇溶液为浸涂液,用涂覆法制备了TiO2／SiO2光催化剂．用XRD,SEM和UV－Vis等对催化剂的物相、形貌及TiO2负载量进行了表征,并通过可溶性染料活性艳红X－3B的降解反应,考察了其光催化活性．实验结果表明,当选用16．79％TiO2／SiO2光催化剂时,活性艳红X－3B溶液的脱色率可达93％以上．     

Gd掺杂TiO2/活性炭纤维复合材料的制备及表征

以TiCl4和Gd(NO3)3·6H2O为主要原料,采用酸催化水解法制备Gd掺杂TiO2光催化剂并通过浸涂法将其负载在活性炭纤维(ACF)表面,制得Gd掺杂TiO2/ACF复合材料。 以气相苯为模型物,考察材料的光催化活性。 利用XRD、FTIR及GC-MS对催化剂的晶相结构、光谱特征等进行了表征。 结果表明,Gd掺杂能有效抑制TiO2的晶粒生长。 Gd掺杂量、浸涂次数影响TiO2/ACF光催化活性,Gd2O3掺杂质量分数为0.48%、浸涂2次的TiO2/ACF活性最高。 在苯光催化氧化后的Gd掺杂TiO2/ACF复合材料表面未发现醌类中间产物的存在。 Gd的掺入能减缓催化剂失活,光催化反应100 min后仍能表现出较高活性。     

Gd掺杂TiO2/活性炭纤维复合材料的制备及表征

以TiCl4和Gd(NO3)3·6H2O为主要原料,采用酸催化水解法制备Gd掺杂TiO2光催化剂并通过浸涂法将其负载在活性炭纤维(ACF)表面,制得Gd掺杂TiO2/ACF复合材料。 以气相苯为模型物,考察材料的光催化活性。 利用XRD、FTIR及GC-MS对催化剂的晶相结构、光谱特征等进行了表征。 结果表明,Gd掺杂能有效抑制TiO2的晶粒生长。 Gd掺杂量、浸涂次数影响TiO2/ACF光催化活性,Gd2O3掺杂质量分数为0.48%、浸涂2次的TiO2/ACF活性最高。 在苯光催化氧化后的Gd掺杂TiO2/ACF复合材料表面未发现醌类中间产物的存在。 Gd的掺入能减缓催化剂失活,光催化反应100 min后仍能表现出较高活性。     

环境湿度对TiO2借性炭纤维气．固光催化氧化甲苯的影响

在恒温控湿的环境舱中，以自制的TiO2／ACF（活性炭纤维）为光催化剂，研究了环境湿度对甲苯光催化降解过程的影响．通过N2吸附和扫描电子显微镜分别对TiO2／ACF光催化剂的孔径结构和形貌特征进行了表征；利用GC—MS和GC—FID对甲苯光催化过程中生成的中间产物进行了定性及定量分析．结果表明，环境舱中相对湿度增大，甲苯光催化转化率提高；不同相对湿度下，积累在光催化剂表面的中间产物种类相同，但支链氧化产物（苯甲醇、苯甲醛和苯甲酸）的积累量远多于苯环氧化产物（甲酚和对甲基苯酚）的积累量；随环境相对湿度的增大．苯甲醛在光催化剂表面的积累量减小，其余中间产物的积累量均有不同程度的增加．这说明水分子在甲苯光催化过程中起重要作用，相对湿度不仅影响甲苯的光催化转化效率，还影响其光催化转化的过程．尽管在各湿度条件下，支链氧化都是甲苯光催化降解的主要途径，但环境湿度增大更有利于苯环氧化途径的进行．讨论了水蒸气在甲苯光催化氧化过程中的作用机理．     

碳纳米管改性TiO2的光催化性能

本文研究碳纳米管改性TiO2光催化剂的制备和影响其光催化性能的因素。实验结果表明，CNT的加入方法，CNT的含量，催化剂的灼烧温度等均影响光催化剂的光催化性能。制备的CNT-TiO2光降解低浓度的甲胺脾农药(40．7lmg／L)具有很好的效果，光催化降解过程符合一级反应动力学方程。     

煤质活性炭的光催化再生

 研究了利用光催化氧化降解反应实现饱和吸附苯酚的煤质活性炭光催化再生的可行性，并分析了活性炭的光催化再生机理．结果表明，在一定条件下可以实现活性炭的光催化再生．在Ag－TiO2负载量为1．9％，pH＝13，θ＝70℃，t＝72h的再生条件下，活性炭的再生率可达 78．4％．在光照条件下，光催化剂作为有机物的降解中心而造成活性炭内外吸附苯酚的浓度差是活性炭光催化再生的主要驱动力．     

B掺杂TiO2/AC光催化剂的制备及活性

以硼酸和钛酸丁酯为主要原料，以活性炭(AC)为载体。用溶胶-凝胶法制备了B掺杂TiO2／AC光催化剂．用X射线衍射(XRD)、紫外可见漫反射吸收光谱(UV—VIS)对制得的光催化剂进行了表征．以甲基橙水溶液的光催化脱色反应和氧化乐果水溶液的光催化降解反应。考查了不同B掺杂TiO2／AC光催化剂的活性．结果表明，所有B掺杂TiO2／AC光催化剂均为锐钛矿晶相．B的掺杂未导致TiO2／AC光催化剂的吸收带边发生明显的移动．当B-TiO2质量分数分别为2．0％和2．5％时，TiO2／AC光催化剂的活性有明显的提高．B-TiO2质量分数2．0％时活性最高．但是，当B-TiO2质量分数分别为1．5％和3．0％时。TiO2／AC光催化剂的活性降低．B的缺电子特性可能改变了TiO2能带中的电子密度，使光催化反应中光生电子和空穴的俘获方式发生变化；同时。B的缺电子特性也会使光催化剂表面的Lewis酸强度增强，导致表面吸附OH-数量和目标反应物的吸附方式发生变化．这些可能是B-TiO2／AC光催化剂活性发生变化的主要原因．     

La2O3掺杂TiO2光催化剂的制备和性能

采用溶胶-凝胶法制备了La2O3掺杂TiO2纳米光催化剂，并通过XRD、TEM、BET和XPS等手段进行了表征．掺入La2O3后，阻止了TiO2从锐钛矿晶型向金红石晶型的转变，使TiO2的粒径减小，比表面积增大．以甲基橙为光催化降解反应模型化合物，考察了光催化剂的活性．测定了甲基橙在纯TiO2和La2O3掺杂TiO2光催化剂上的吸附常数．考察了pH、H2O2对降解性能的影响．讨论了光催化活性与催化剂性质的关系．     

TiO_2表面NiO光催化活性中心的构建及其光催化析氢性能研究

本文采用离子快速注入法,在低温条件下利用微量NiO物种对TiO_2光催化剂表面微结构进行了修饰和改性,构建了NiO光催化反应活性中心。研究结果表明,Ni物种是以TiO_2-NiO-H形式存在于TiO_2表面;相对于未修饰的TiO_2光催化剂,NiO的修饰很大程度上提高了其光催化析氢性能,在最佳条件下,放氢速率由1.1μmol·h~(-1)提高到241.4μmol·h~(-1)。另外,Ni物种含量,热处理温度,乙醇电子给体浓度,催化剂悬浮浓度对光催化析氢性能也有明显的影响。光电化学实验结果表明,NiO的表面修饰能够产生有效的光催化反应活性中心,增强了光生电子-空穴电子对的分离效果。所制备的光催化剂采用X射线粉末衍射(XRD),光电子能谱(XPS)等技术进行表征。     

紫外光照射下丙炔光催化水解反应的研究 Ⅰ．纳米二氧化钛光催化剂的性能

 采用5种不同的纳米二氧化钛为光催化剂,考察了它们在丙炔水解反应中的光催化活性,并用X射线衍射和漫反射紫外－可见吸收光谱技术进行了表征．研究了催化剂表面物理化学性质与在丙炔光催化水解反应中的构效关系．实验结果表明,纳米二氧化钛光催化剂能够引发丙炔的光催化水解反应,生成乙烷和乙烯等产物;锐钛矿相纳米二氧化钛具有较高的光催化活性,在晶型相同的情况下,影响光催化活性的主要因素是催化剂的粒径和比表面积．     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.