Preparation and application of a coated‐fiber needle extraction device

In this study, a needle‐trap device with fibers coated with a molecularly imprinted polymer was developed for separation. A number of heat‐resistant Zylon filaments were longitudinally packed into a glass capillary, followed by coating with a molecularly imprinted polymer. Then, the molecularly imprinted polymer coating was copolymerized and anchored onto the surface of the fibers. The bundle of synthetic fibers coated with the molecularly imprinted polymer was packed into a 21G stainless‐steel needle and served as an extraction medium. The coated‐fiber needle extraction device was used to extract volatile organic compounds from paints and gasoline effectively. Subsequently, the extracted volatile organic compounds were analyzed by gas chromatography. Calibration curves of gaseous benzene, toluene, ethylbenzene, and o‐xylene in the concentration range of 1–250 μg/L were obtained to evaluate the method, acceptable linearity was attended with correlation coefficients above 0.998. The limit of detection of benzene, toluene, ethylbenzene, and o‐xylene was 11–20 ng/L using the coated‐fiber needle‐trap device. The relative standard deviation of needle‐to‐needle repeatability was less than 8% with an extraction time of 20 min. The loss rates after storage for 3 and 7 days at room temperature were less than 30%.     

Molecularly imprinted stir bars for selective extraction of thiabendazole in citrus samples

Stir‐bar sorptive extraction is based on the partitioning of target analytes between the sample (mostly aqueous‐based liquid samples) and a stationary phase‐coated magnetic stir bar. Until now, only PDMS‐coated stir bars are commercially available, restricting the range of applications to the non‐selective extraction of hydrophobic compounds due to the apolar character of PDMS. In this work, a novel stir bar coated with molecularly imprinted polymer as selective extraction phase for sorptive extraction of thiabendazole (TBZ) was developed. Two different procedures, based on physical or chemical coating, were assessed for the preparation of molecularly imprinted stir bars. Under optimum conditions, recoveries achieved both in imprinted and non‐imprinted polymer stir bars obtained by physical coating were very low, whereas TBZ was favourably retained by imprinted over non‐imprinted polymer stir bars obtained by chemical coating and thus the latter approach was used in further studies. Different parameters affecting both stir‐bars preparation (i.e. cross‐linker, porogen, polymerization time) and the subsequent selective extraction of TBZ (i.e. washing, loading and elution solvents, extraction time) were properly optimized. The molecularly imprinted coated stir bars were applied to the extraction of TBZ from citrus samples (orange, lemon and citrus juices) allowing its final determination at concentrations levels according to current regulations.     

Preparation and selective recognition of a novel solid‐phase microextraction fiber combined with molecularly imprinted polymers for the extraction of parabens in soy sample

A prepared molecularly imprinted polymer with ethyl p‐hydroxybenzoate as template molecule was applied for the first time to a homemade solid‐phase microextraction fiber. The molecularly imprinted polymer‐coated solid‐phase microextraction fiber was characterized by scanning electron microscopy and thermogravimetric analysis. Various parameters were investigated, including extraction temperature, extraction time, and desorption time. Under the optimum extraction conditions, the molecularly imprinted polymer‐coated solid‐phase microextraction fiber exhibited higher selectivity with greater extraction capacity toward parabens compared with the nonimprinted polymer‐coated solid‐phase microextraction fiber and commercial fibers. The molecularly imprinted polymer‐coated solid‐phase microextraction fiber was tested using gas chromatography to determine parabens, including methyl p‐hydroxybenzoate, ethyl p‐hydroxybenzoate, and propyl p‐hydroxybenzoate. The linear ranges were 0.01–10 μg/mL with a correlation coefficient above 0.9943. The detection limits (under signal‐to‐noise ratio of 3) were below 0.30 μg/L. The fiber was successfully applied to the simultaneous analysis of three parabens in spiked soy samples with satisfactory recoveries of 95.48, 97.86, and 92.17%, respectively. The relative standard deviations (n=6) were within 2.83–3.91%. The proposed molecularly imprinted polymer‐coated solid‐phase microextraction method is suitable for selective extraction and determination of trace parabens in food samples.     

Development of metal complex imprinted solid-phase microextraction fiber for 2,2'-dipyridine recognition in aqueous medium

In this paper, a novel metal complex imprinted polymer (CIP) coated solid-phase microextraction (SPME) fiber was prepared which could recognize the complex template [Cu(OAc)₂(2,2′-dipyridine)] in aqueous medium. The saturating adsorption capacity of CIP-coated fiber was 2.2 and 2.6 times greater than those of molecularly imprinted polymer (MIP) coated fiber and nonimprinted polymer (NIP) coated fiber, respectively. Extraction conditions that influenced the recognition performance of CIP-coated fiber were investigated including pH, extraction solvent, metal ion species, etc. The ligand selectivity was also evaluated and discussed. The results demonstrated that CIP-coated fiber had better binding affinity for 2,2′-dipyridine compared to its structure analogues. The recognition ability of CIP coating was stable and effective in aqueous medium while MIP coating showed weak imprinting effect due to disturbance from protic solvent. 2,2′-dipyridine extracted by CIP-coated fiber using HPLC/UV detection resulted in a linear range of 10-200 μg/L with a detection limit of 2.0 μg/L. The proposed method was successfully applied to the analysis of 2,2′-dipyridine in spiked tap water, laboratory wastewater and human urine samples with recoveries 80.3-103.3% and RSDs 5.5-8.9%.     

Ultra‐rapid non‐equilibrium solid‐phase microextraction at elevated temperatures and direct coupling to mass spectrometry for the analysis of lidocaine in urine

Solid‐phase microextraction (SPME) has been directly coupled to an ion‐trap mass spectrometer (MS) for the determination of the model compound lidocaine in urine, hereby applying MS/MS [fragmentation of [M + H]⁺ (m/z 235) to a fragment with m/z 86]. The throughput of samples has been increased using non‐equilibrium SPME with polydimethylsiloxane (PDMS) fibers. The effect of temperature on the sorption and the desorption was studied. Elevated temperatures during sorption (65°C) and desorption (55°C) had a considerable influence on the speed of the extraction. The desorption was carried out with a home‐made desorption chamber allowing thermostating. Only 1 min sorption and 1 min desorption were performed, after which MS detection took place, resulting in a total analysis time of 3 min. Detection limits below 1 ng/mL could be obtained despite yields of only 2.1 and 1.5% for a 100‐ and a 30‐μm PDMS‐coated fiber, respectively. Furthermore, the determination of lidocaine in urine had acceptable reproducibilities, i.e., relative standard deviations (RSDs) below 10%. A limit of quantitation (RSD < 15%) of about 1 ng/mL was obtained. No extra wash step of the extraction fiber was required after desorption if a 30‐μm coating was used, whereas not all the analyte was desorbed from the 100‐μm coating in a single desorption. Therefore, the SPME‐MS/MS system with a 30‐μm PDMS‐coated fiber for rapid non‐equilibrium SPME at elevated temperatures has interesting potential for high‐throughput analysis of biological samples.     

Graphene‐coated fiber for solid‐phase microextraction of triazine herbicides in water samples

Graphene is a novel and interesting carbon material that could be used for the separation and purification of some chemical compounds. In this investigation, graphene was used as a novel fiber‐coating material for the solid‐phase microextraction (SPME) of four triazine herbicides (atrazine, prometon, ametryn and prometryn) in water samples. The main parameters that affect the extraction and desorption efficiencies, such as the extraction time, stirring rate, salt addition, desorption solvent and desorption time, were investigated and optimized. The optimized SPME by graphene‐coated fiber coupled with high‐performance liquid chromatography‐diode array detection (HPLC‐DAD) was successfully applied for the determination of the four triazine herbicides in water samples. The linearity of the method was in the range from 0.5 to 200 ng/mL, with the correlation coefficients (r) ranging from 0.9989 to 0.9998. The limits of detection of the method were 0.05‐0.2 ng/mL. The relative standard deviations varied from 3.5 to 4.9% (n=5). The recoveries of the triazine herbicides from water samples at spiking levels of 20.0 and 50.0 ng/mL were in the range between 86.0 and 94.6%. Compared with two commercial fibers (CW/TPR, 50 μm; PDMS/DVB, 60 μm), the graphene‐coated fiber showed higher extraction efficiency.     

A high selective ion‐imprinted polymer grafted on a novel nanoporous material for efficient gold extraction

In this work, for the first time, an ion‐imprinted polymer was developed for selective extraction and determination of gold ions. To increase the sorbent efficiency, this polymer was coated on a novel nanoporous carbon‐based material, carbohydrate‐derived Max‐Planck Gesellschaft 1, which is also the first example of grafting imprinted polymer on nanoporous‐carbon material. These particles were applied successfully for preconcentration of ultratrace amount of gold ions, following determination by flame atomic absorption spectrometry. Some effective factors on the efficiency of gold ions extraction, such as concentration and volume of eluent, sample and eluent flow rates, and also effect of interfering ions especially palladium and platinum ions, were investigated. The LOD was determined to be 0.27 ng/mL. Furthermore, the precision of the method was calculated to be 2.14% under optimal conditions with recovery more than 97.3%. The technique was also used to determine the concentration of gold ions in mine stone samples with satisfactory results. The accuracy of this method was investigated by determination of gold ions concentrations in several reference materials with certified gold content.     

Preparation and application of molecularly imprinted polymer solid‐phase microextraction fiber for the selective analysis of auxins in tobacco

As signal molecules, auxins play an important role in mediating plant growth. Due to serious interfering substances in plants, it is difficult to accurately detect auxins with traditional solid‐phase extraction methods. To improve the selectivity of sample pretreatment, a novel molecularly imprinted polymer ‐coated solid‐phase microextraction fiber, which could be coupled directly to high‐performance liquid chromatography, was prepared with indole acetic acid as template molecule for the selective extraction of auxins. The factors influencing the polymer formation, such as polymerization solvent, cross‐linker, and polymerization time, were investigated in detail to enhance the performance of indole acetic acid‐molecularly imprinted polymer coating. The morphological and chemical stability of this molecularly imprinted polymer‐coated fiber was characterized by scanning electron microscopy, infrared spectrometry, and thermal analysis. The extraction capacity of the molecularly imprinted polymer‐coated solid‐phase microextraction fiber was evaluated for the selective extraction of indole acetic acid and indole‐3‐pyruvic acid followed by high‐performance liquid chromatography analysis. The linear range for indole acetic acid and indole‐3‐pyruvic acid was 1–100 µg/L and their detection limit was 0.5 µg/L. The method was applied to the simultaneous determination of two auxins in two kinds of tobacco (Nicotiana tabacum L and Nicotiana rustica L) samples, with recoveries range from 82.1 to 120.6%.     

Preparation and Characterization of Prometryn Molecularly Imprinted Solid‐Phase Microextraction Fibers

Abstract

A novel reproducible solid‐phase microextraction (SPME) coating was prepared on the surface of silanized silica fibers by molecularly imprinted polymerization using prometryn as template molecule. The structure and extraction performance of molecularly imprinted polymer (MIP) coating was studied with the scanning electron microscope and high performance liquid chromatography (HPLC). Specific selectivity was found with the prometryn MIP‐coated fiber to prometry and its structural analogues such as atrazine, simetryn, terbutylazin, ametryn, propazine and terbutryn. In contrast, these triazines could not be selectively extracted by the non‐imprinted polymer fiber or commercial polydimethylsiloxane (PDMS), polydimethylsiloxane/divinylbenzene (PDMS/DVB), polyacrylate (PA) fibers.     

Application of a new fiber coating based on electrochemically reduced graphene oxide for the cold‐fiber headspace solid‐phase microextraction of tricyclic antidepressants

A new fiber based on the electrochemical reduction of graphene oxide was prepared on a copper wire for solid‐phase microextraction (SPME) applications. The prepared fiber was used for the SPME and gas chromatographic analysis of tricyclic antidepressants (TCADs), including amitriptyline, trimipramine, and clomipramine. The feasibility of direct‐immersion and headspace modes of SPME for the determination of TCADs was studied. The effects of four parameters including pH, salt content, extraction temperature with and without cooling the fiber, and extraction time were investigated. The comparison showed that headspace cold fiber SPME results in the best outcome for the extraction of TCADs. Under the optimized conditions of this mode, the calibration curves were linear between 2.0 and 500 ng/mL and the detection limits were between 0.30 and 0.53 ng/mL. The intraday and interday RSDs obtained at 20 ng/mL (n = 5), using a single fiber, were 5.5–9.0 and 7.5–9.8, respectively. The fiber to fiber repeatability (n = 4), expressed as the RSD, was between 12.8 and 13.2% at a 20 ng/mL concentration level. The method was successfully applied to the analysis of TCADs in plasma samples showing recoveries from 73 to 96%.     

Development of a solid‐phase microextraction fiber coated with poly(methacrylic acid‐ethylene glycol dimethacrylate) and its application for the determination of chlorophenols in water coupled with GC

A solid‐phase microextraction (SPME) fiber coated with poly(methacrylic acid‐ethylene glycol dimethacrylate) coupled to GC with a micro electron‐capture detector was developed for the determination of four chlorphenols in water samples for the first time. A novel and simple method for the preparation of this novel SPME fiber was proposed by copolymerization of methacrylic acid and ethylene glycol dimethacrylate in an appropriate solvent using a glass capillary as a “mold”. The factors affecting the polymerization were optimized in detail. Furthermore, the extraction performance of the poly(methacrylic acid‐ethylene glycol dimethacrylate) fiber was evaluated. Moreover, experimental headspace‐SPME parameters, such as extraction temperature, extraction time, salt concentration, stirring speed, and pH, were optimized by orthogonal array experimental designs. Under the optimized conditions, the target analytes were linear in the range of 0.2–50 ng/mL, and the correlation coefficients were all greater than 0.99. RSD was less than 8.9%, and the detection limits were in the range of 0.1–10 ng/L. Four cholorphenols were detected from tap and lake water samples using the proposed method, with the recoveries of spiked natural water samples were ranged from 91.8 to 110.8, and 90.6 to 111.4% for tap and lake water samples, respectively.     

Preparation of magnetic molecularly imprinted polymer for dispersive solid‐phase extraction of valsartan and its determination by high‐performance liquid chromatography: Box‐Behnken design

In this work, core/shell magnetic molecularly imprinted polymer nanoparticles were synthesized for extraction and pre‐concentration of valsartan from different samples and then it was measured with high‐performance liquid chromatography. For preparation of molecularly imprinted polymer nanoparticles, Fe₃O₄ nanoparticles were coated with tetraethyl orthosilicate and then functionalized with 3‐(trimethoxysilyl) propyl methacrylate. In the next step, molecularly imprinted polymer nanoparticles were synthesized under reflux and distillation conditions via polymerization of methacrylic acid, valsartan (as a template), azobisisobutyronitrile and ethylene glycol dimethacrylate as cross linking. The properties of molecularly imprinted polymer nanoparticle were investigated by FTIR spectroscopy, field emission scanning electron microscopy, and X‐ray diffraction. Box‐Behnken design with the aid of desirability function was used for optimizing the effect of variables such as the amounts of molecularly imprinted polymer nanoparticles, time of sonication, pH, and volume of methanol on the extraction percentage of valsartan. According to the obtained results, the affecting variables extraction condition were set as 10 mg of adsorbent, 16 min for sonication, pH = 5.5 and 0.6 mL methanol. The obtained linear response (r² > 0.995) was in the range of 0.005–10 µg/mL with detection limit 0.0012 µg/mLand extraction recovery was in the range of 92–95% with standard deviation less than 6% (n = 3).     

Yttria‐based sol–gel coating for capillary microextraction online coupled to high‐performance liquid chromatography

This work about the development of yttria‐based polymeric coating using [bis(hydroxyethyl) amine] terminated polydimethylsiloxanes and yttrium trimethoxyethoxide inside the capillary. The coated capillary was utilized for online capillary microextraction and high‐performance liquid chromatography analysis. The prepared coating material was characterized using scanning electron microscopy, X‐ray photoelectron spectroscopy, energy dispersive X‐ray spectrometry, and thermogravimetric analysis. The coated capillary with polymer presented better extraction efficiency compared with the pure yttria‐based coated capillary with applicability in extreme pH environments (pH 0–pH 14). Excellent extraction towards polyaromatic hydrocarbons, aldehydes, ketones, alcohols, phenols, and amides was observed with limit of detection ranging from 0.18 to 7.35 ng/mL (S/N = 3) and reproducibility in between 0.6 and 6.8% (n = 3). Capillary‐to‐capillary extraction analysis has presented reproducibility between 4.1 and 9.9%. The analysis provided linear response for seven selected phenols in the range of 5–200 ng/mL with R² values between 0.9971 and 0.9998. The inter‐day, intra‐day, and capillary‐to‐capillary reproducibility for phenols was also <10%. Real sample analysis by spiking 5, 50, and 200 ng/mL of phenols in wastewater and pool‐water produced recovery between 84.7 and 94.3% and reproducibility within 7.6% (n = 3).     

Molecularly imprinted polymer as a novel solid‐phase microextraction coating for the selective enrichment of trace imidazolinones in rice,peanut, and soil

The development and application of an imazethapyr molecularly imprinted polymer‐based solid‐phase microextraction coating were investigated. A novel molecularly imprinted polymer coating with imazethapyr as template was firstly prepared by a one‐step in situ polymerization method, and demonstrated specific selectivity to imidazolinone herbicides in complicated samples. The structural characteristics and extraction performance of the imazethapyr molecularly imprinted polymer coating were studied. The molecularly imprinted polymer coating was homogeneous, dense, and heat and solvent resistant. Adsorption capacity experiments showed that the molecularly imprinted polymer coating could selectively extract imazethapyr and its structural analogs, and the maximum adsorption capacity was 2.5 times as much as that of the nonimprinted polymer coating. A method for the determination of five imidazolinones by imazethapyr molecularly imprinted polymer solid‐phase microextraction coupled with high‐performance liquid chromatography was developed. The linear range was 0.50–50 μg/L for imazameth, imazamox, imazapyr acid, and imazethapyr, and 1.0–100 μg/L for imazaquin acid, and the detection limits were within the range of 0.070–0.29 μg/L. The method was applied to simultaneous and multiresidual determinations of trace imidazolinones in rice, peanut, and soil samples with satisfactory recoveries of 60.6–99.5, 79.1–123, and 61.3–116%, respectively, and relative standard deviations of 0.40–10%, which indicated that this method was suitable for the trace analysis of imidazolinones in complex food and environmental samples.     

Synthesis of novel ion‐imprinted polymeric nanoparticles based on dibenzo‐21‐crown‐7 for the selective pre‐concentration and recognition of rubidium ions

In this work, we report the first application of ion‐imprinted technology via precipitation polymerization for simple and practical determination of rubidium ions. The rubidium‐ion‐imprinted polymer nanoparticles were prepared using dibenzo‐21‐crown‐7 as a selective ligand, methacrylic acid as functional monomer, ethylene glycol dimethacrylate as cross linker, and 2,2′‐azobisisobutyronitrile as radical initiator. The resulting powder material was characterized using scanning electron microscopy, which showed colloidal nanoparticles of 100–200 nm in diameter and slightly irregular in shape. The maximum adsorption capacity of the ion imprinted particles was 63.36 μmol/g. The experimental conditions such as nature and concentration of eluent, pH, adsorption and desorption times, weight of the polymer material, aqueous phase and desorption agent volumes were also studied. Finally, selectivity of the prepared IIP particles toward rubidium ion was investigated in the presence of some foreign metal ions.     

Fe3O4/polyethylene glycol nanocomposite as a solid‐phase microextraction fiber coating for the determination of some volatile organic compounds in water

A high‐performance metal oxide polymer magnetite/polyethylene glycol nanocomposite was prepared and coated in situ on the surface of the optical fiber by sol–gel technology. The magnetite nanoparticles as nanofillers were synthesized by a coprecipitation method and bonded with polyethylene glycol as a polymer. The chemically bonded coating was evaluated for the headspace solid–phase microextraction of some environmentally important volatile organic compounds from aqueous samples in combination with gas chromatography and mass spectrometry. The prepared fiber was characterized by scanning electron microscopy and Fourier transform infrared spectroscopy. The mass ratio of nanofiller and polymer on the coating extraction efficiency, morphology, and stability were investigated. The parameters affecting the extraction efficiency, including the extraction time and temperature, the ionic strength, desorption temperature, and time were optimized. The sol–gelized fiber showed excellent chemical stability and longer lifespan. It also exhibited high extraction efficiency compared to the two types of commercial fibers. For volatile organic compounds analysis, the new fiber showed low detection limits (0.008–0.063 ng/L) and wide linearity (0.001–450 × 10⁴ ng/L) under the optimized conditions. The repeatability (interday and intraday) and reproducibility were 4.13–10.08 and 5.98–11.61%, and 7.35–14.79%, respectively (n = 5). For real sample analysis, three types of water samples (ground, surface, and tap water) were studied.     

Polypyrrole–montmorillonite nanocomposite as sorbent for solid‐phase microextraction of phenolic compounds in water

A fiber‐coated polypyrrole–montmorillonite nanocomposite was prepared for solid‐phase microextraction. The fiber coating can be prepared easily; it is mechanically stable and exhibits relatively high thermal stability. The prepared fiber was evaluated for the extraction of some phenolic compounds from aqueous sample solutions by gas chromatography–mass spectrometry. The effects of the extraction and desorption parameters including extraction time, extraction temperature, stirring rate, ionic strength, pH and desorption temperature and time have been studied. At optimum conditions, the repeatability for one fiber (n = 5), expressed as % relative standard deviation was between 6.5 and 7.8% for the phenolic compounds. The detection limits for the studied phenolic compounds were between 0.05–1.3 ng/mL. The developed method offers the advantage of being simple to use, with shorter analysis time, lower cost, thermal stability of the fibers, and high relative recovery in comparison to conventional methods of analysis.     

Polythiophene/hexagonally ordered silica nanocomposite coating as a solid‐phase microextraction fiber for the determination of polycyclic aromatic hydrocarbons in water

A highly porous fiber coated with polythiophene/hexagonally ordered silica nanocomposite was prepared for solid‐phase microextraction (SPME). The prepared nanomaterial was immobilized onto a stainless‐steel wire for the fabrication of the SPME fiber. Polythiophene/hexagonally ordered silica nanocomposite fibers were used for the extraction of some polycyclic aromatic hydrocarbons from water samples. The extracted analytes were transferred to the injection port of a gas chromatograph using a laboratory‐designed SPME device. The results obtained prove the ability of the polythiophene/hexagonally ordered silica material as a new fiber for the sampling of organic compounds from water samples. This behavior is due most probably to the increased surface area of the polythiophene/hexagonally ordered silica nanocomposite. A one‐at‐a‐time optimization strategy was applied for optimizing the important extraction parameters such as extraction temperature, extraction time, ionic strength, stirring rate, and desorption temperature and time. Under the optimum conditions, the LOD of the proposed method is 0.1–3 pg/mL for analysis of polycyclic aromatic hydrocarbons from aqueous samples, and the calibration graphs were linear in a concentration range of 0.001–20 ng/mL (R² > 0.990) for most of the polycyclic aromatic hydrocarbons. The single fiber repeatability and fiber‐to‐fiber reproducibility were less than 8.6 and 19.1% (n = 5), respectively.     

Core–shell SiO2‐coated Fe3O4 with a surface molecularly imprinted polymer coating of folic acid and its applicable magnetic solid‐phase extraction prior to determination of folates in tomatoes

A novel core–shell magnetic surface molecularly imprinted polymer with folic acid as a template was successfully synthesized by the sol–gel method. To generate Lewis acid sites in the silica matrix for the interaction of the metal coordinate with the template, 3‐aminopropyltriethoxysilane was used as a functional monomer, tetraethyl orthosilicate as a cross‐linker, and aluminum ions as a dopant. The magnetite encapsulated by the silica shell plays an important role as a magnetic‐coated polymer. The synthesized product was characterized by powder X‐ray diffraction, scanning electron microscopy, transmission electron microscopy, and FTIR and UV/Vis spectroscopy. The powder X‐ray diffraction patterns, FTIR and UV/Vis spectra confirmed the characteristics of the as‐prepared silica coated magnetite and folic acid molecularly imprinted polymer. It was successfully applied for magnetic solid‐phase extraction prior to the determination of folates in tomato samples using high‐performance liquid chromatography with photodiode array detection. The detection limit of the proposed method was 1.67 μg/L, and results were satisfactory, with a relative standard deviation of < 3.94%.     

Preparation and Characterization of Metolachlor Molecularly Imprinted Polymer Coating on Stainless Steel Fibers for Solid-Phase Microextraction

A molecularly imprinted polymer (MIP) with metolachlor as the template molecule was first coated on the surface of stainless steel fibers through chemical bonding. Despite 12 times repeated coating procedures, a homogenous, porous, and highly cross-linked MIP coating was obtained with thickness of 17.4 µm (RSD of 6.1%). The specific selectivity of MIP coating to metolachlor and three metabolites could be concluded with 4.4, 4.1, 3.9, and 2.9 times higher extraction amounts of metolachlor, hydroxymetolachlor, deschlorometolachlor, and desmethylmetolachlor than that of the NIP coating, respectively, and good extraction capabilities for chloroacetanilide herbicides were found with the MIP-coated SPME stainless steel fiber. For validation, the fiber was applied for the extraction of metolachlor, propisochlor, and butachlor in spiked corn and soybean samples, and the recoveries of 90.7–92.6%, 86.4–87.9, and 85.4–87.5% were obtained, respectively.