Indirect Determination of Ascorbic Acid with Ammonium Sulfate and Ethanol by Extraction and Flotation of Copper

A new method of indirect determination of ascorbic acid with ammonium sulfate and ethanol by extraction and flotation of copper in the presence of thiocyanate has been studied in this paper. The study shows that a small amount of Cu(II) is reduced to Cu(I) by ascorbic acid, then Cu(I) precipitates with SCN^?. In the course of phase separation of ethanol from water, the precipitated CuSCN is extracted and stays in the interface of ethanol and water. A good linear relationship is observed between the extraction yield of Cu(II) and the amount of ascorbic acid. The detection limit for ascorbic acid is 1 10^?5 M. Every parameter has been optimized and the reaction mechanism has been studied. The method is simple, rapid (5 min) and suffers from few interferences of common anions and cations. It has been successfully applied for the determination of ascorbic acid in pharmaceuticals and fruits.     

Indirect Determination of Ascorbic Acid with Ammonium Sulfate and Isopropyl Alcohol by Extraction-flotation of Copper

A new method of indirect determination of ascorbic acid(Vc) with ammonium sulfateand isopropyl alcohol by extraction-flotation of copper is studied in this paper. It shows that asmall amount of Cu( II ) can be reduced to Cu( I ) by Vc, then Cu( I ) reacted with the SCN-,which precipitated on the interface of isopropyl alcohol and H2O. A good linear relationshin is observed between the flotation yield(E) of Cu( II ) and the amount of Vc. The detection limi(forVc is 1.76 μg/mL. The method is simple, rapid (5 rain), but suffers from little interference of common anions and cations. It has been successfully applied for the determination of Vc in fruits.     

Spectrophotometric determination of a nanomolar amount of ascorbic acid using its catalytic effect on copper(II) porphyrin formation

A simple, fast and sensitive flow-injection method is proposed for the determination of nanomolar amounts of ascorbic acid in tea, urine and blood. The procedure is based on the accelerating effect of a nanomolar level of ascorbic acid on the reaction of cooper(II) with 5,10,15,20-tetrakis(1-methylpyridinium-4-yl)porphyrin, H(2)tmpyp(4+). Ascorbic acid reduces Cu(II) to Cu(I) which catalyzes the incorporation of Cu(II) into H(2)tmpyp(4+) to form Cu(II)(tmpyp)(4+). In this method two solutions, one containing ascorbic acid and H(2)tmpyp(4+) and the other containing copper(II) and acetate buffer (pH 5.0), were injected into two flowing streams of water through two sample injectors of 120 mu1 sample volume. The mixture was allowed to react in a 2 m reaction coil and the colored solution of Cu(II)(tmpyp)(4+) was monitored at 550 nm (epsilon = 2.01 x 10(4)M(-1)cm(-1)). The present method was applied to the determination of ascorbic acid in tea, urea and blood. Reducing agents such as sugars and vitamins B(1), B(2), B(6) and B(12) did not give serious errors at a concentration of 10(-6) M for the determination of 1.0 x 10(-8)M ascrobic acid. The relative standard deviation of the present method was 2.8% for the determination of 1.0 x 10(-8)M ascorbic acid. The reaction mechanism was clarified from the kinetic results of the formation of Cu(II)(tmpyp)(4+) in the presence of various concentrations of ascorbic acid, copper(II) and hydrogen ion.     

Indirect Determination of Sodium Cefotaxime with N‐Propyl Alcohol‐Ammonium Sulfate‐Water System by Extraction‐Flotation of Cuprous Thiocyanate

A novel method for the indirect determination of sodium cefotaxime by the extraction‐flotation of cuprous thiocyanate is described in this paper. The experiment indicated that the degradation of sodium cefotaxime took place in the presence of 0.20 M sodium hydroxide in a boiling water bath for 40 min. At pH 4.0, the thiol group (‐SH) of the degradation product of sodium cefotaxime could reduce Cu(II) to Cu(I) for the formation of the emulsion CuSCN precipitation in the presence of ammonium thiocyanate. By determining the residual amount of Cu(II) in the solution and calculating the flotation yield of CuSCN, the indirect determination of sodium cefotaxime can be achieved. When the concentration of Cu(II) was 5.0 μg mL^?1, a good linear relationship was obtained between the flotation yield of CuSCN and the amount of sodium cefotaxime in the range of 0.50～20 μg mL^?1. The linear equation is E = 1.329 + 2.654C with a correlation coefficient r = 0.9988. The detection limit of sodium cefotaxime of this proposed method evaluated by calibration curve (3σ/k) was found to be 0.39 μg mL^?1. Every parameter has been optimized and the reaction mechanism has been studied. This method has been successfully applied to the determination of sodium cefotaxime in pharmaceutical formulations, human serum, and urine samples, respectively. Analytical results obtained with this novel method are satisfactory.     

Indirect determination of ampicillin sodium with sodium nitrate-ammonium thiocyanate-water system by extraction-flotation of cuprous thiocyanate

A novel method for indirect determination of ampicillin sodium by the extraction-flotation is proposed in this paper. It is indicated that the degradation of ampicillin sodium took place in the presence of 0.30 M sodium hydroxide in boiling water for 20 min. At pH 4.0, in the presence of ammonium thiocyanate, the thiol group of the degradation product of ampicillin sodium could reduce copper(II) to copper(I) due to the formation of the emulsion cuprous thiocyanate precipitation. By determining the residual amount of copper(II) in the solution and calculating the flotation yield of cuprous thiocyanate, the indirect determination of ampicillin sodium can be performed. When the concentration of cooper(II) was 5.0 μg/mL, a good linear relationship was obtained between the flotation yield of cuprous thiocyanate and the amount of ampicillin sodium in the range of 0.40～9.6 μg/mL. The linear equation is E = 4.1469 + 3.7949c with the correlation coefficient r = 0.9992, and the detection limit (3σ/K) of 0.37 μg/mL. Each parameter has been optimized and the reaction mechanism has been studied. The method has been successfully applied to the determination of ampicillin sodium in pharmaceutical, human plasma and urine samples. Analytical results obtained are satisfactory.     

Ion flotation behaviour of thirty-one metal ions in mixed hydrochloric/nitric acid solutions

The ion flotation of 31 metal ions in hydrochloric/nitric acid solution with the cationic surfactant cetylpyridinium chloride was investigated. A 25-ml portion of 0.27-2.87 x 10(-4)M metal ion and 1.8-6.0 x 10(-4)M cetylpyridinium chloride solution in 0.17-3.4M acid mixture ([HCl]:[HNO(3)] = 2.4:1) was subjected to flotation in a cell, 22.5 cm high and 4.0 cm in diameter, for 5 min, with nitrogen bubbles. Ir(IV), Pt(IV), Ge(IV), Sn(IV), Bi(III), Au(III), Tl(III), Pd(II) and Sn(II) were floated from solution in 95-100% yield; Ru(III), Rh(III), Ir(III), Hg(II), Ag(I) and Tl(I) were partly floated, while Cr(VI), Ti(IV), Zr(IV), Ga(III), In(III), Fe(III), Sb(III), Al(III), Mn(II), Fe(II), Co(II), Ni(II), Cu(II), Zn(II), CD(II) and Pb(II) were floated with less than 20% yield. The flotation behaviour of these metal ions in the mixed acid system was compared with that in hydrochloric acid. The flotation is more efficient in the mixed acid system.     

Fabrication of PVC based membrane using nickel porphyrazine as ionophore in the screening of thiocyanate ion in aqueous and real samples

The [Ni[(TAP)(SBn)8]] complex (I), i.e. ([2,3,7,8,12,13,17,18-octakis(benzylthio)-5,10,15,20-tetraazaporphyrin])nickel(II), has been explored as an ionophore for fabrication of the PVC based membrane electrodes used in the screening of thiocyanate anion (SCN-). The membrane having [Ni[(TAP)(SBn)8]] complex (I) as an electroactive material and dioctylphthalate (DOP) as plasticizer in the PVC matrix with the percentage ratio 5 : 158 : 200 (I : DOP : PVC, % w/w) exhibited a linear response in the concentration range 7.0 x 10(-6)-1.0 x 10(-1) M of SCN- with a sub-Nernstian slope 32.5 +/- 0.2 mV/decade of activity and a fast response time of 10 +/- 2 s. The sensor works well in the pH range 3.0 - 9.5 and could be satisfactorily used in presence of 50 % (v/v) methanol, ethanol and acetone, and is selective for SCN- over a large number of anions with slight interference from iodide (I-) and azide (N3-) if present at a level >or = 1.0 x 10(-5) M. Described electrode works well over a period of six months. The sensor can be successfully applied for the screening of SCN- in both aqueous and real samples and also as indicator electrodes in precipitation titrations.     

The Study of Indirect Determination of Tiopronin by Extraction Flotation Copper(II) with an Ammonium Sulfate‐Water‐n‐Propyl Alcohol System

A novel method for indirect determination of tiopronin by extraction flotation of copper(II) with an ammonium sulfate‐water‐n‐propyl alcohol system was developed. The effects of different parameters, such as acidity, the amount of NH₄SCN and various salts on the flotation yield of Cu(II), have been studied to optimize the experimental conditions. Under the optimum conditions, Cu(II) is reduced to Cu(I) by tiopronin, and the resulting Cu(I) can react with SCN^? to form a white emulsion precipitate CuSCN. In the presence of (NH₄)₂SO₄, the mixture consisting of n‐propyl alcohol and water can be separated into an n‐propyl alcohol phase and a water phase. In the process of phase separation of n‐propyl alcohol from water, the precipitated CuSCN is extracted and stays in the interface of n‐propyl alcohol and water. The amount of tiopronin can be determined by measuring the flotation yield of Cu(II). The detection limit is 0.32 mg L^?1 and the linear range is maintained in the range of 0.40±13.0 mg L^?1 with a correlation coefficient of 0.9991. This proposed method has been successfully applied to the determination of tiopronin in tablets, urine and human plasma with satisfactory results.     

Kinetic method for determination of ascorbic acid on flow injection system by using its catalytic effect on the complexation reaction of an ultra sensitive colorimetric reagent of porphyrin with Cu(II)

A kinetic method performed on a flow injection system is described for the determination of ascorbic acid by using its catalytic effect on the complexation reaction of Cu(II) with 5,10,15,20-tetrakis(4-N-trimethyl-aminophenyl)porphyrin. The characteristic spectrum of porphyrin (Soret band), which shows intense absorption around 400 nm (epsilon>2.0 x 10(5) cm(-1)M(-1)), was used first time for determining ascorbic acid. By incorporating the complexation reaction into a flow injection system, ascorbic acid could be determined either over a broad dynamic range of 0.1-1000 microg/ml or at a trace level below 5 ng/ml. Good repeatability was also achieved by testing a working standard of 0.1 microg/ml with 10 injections at a throughput of 35 h(-1), obtaining a relative standard deviation of 0.11%. Substances like amino acids, vitamins, sugars, organic acids and metal ions, showed no or little interference even present at high concentrations. The method was validated in the determination of ascorbic acid contents of some commercially available soft drinks by comparison with the official 2,6-dichloroindophenol method with reasonable agreement.     

Determination of SCN- in urine and saliva of smokers and non-smokers by SCN(-)-selective polymeric membrane containing a nickel(II)-azamacrocycle complex coated on a graphite electrode.

The construction, performance characteristics, and application of a novel polymeric membrane coated on a graphite electrode with unique selectivity towards SCN- are reported. The electrode was prepared by incorporating Ni(II)-2,2,4,9,9,11-hexamethyltetraazacyclotetradecanediene perchlorate into a plasticized poly(vinyl chloride) membrane. The influences of membrane composition, pH and foreign ions were investigated. The electrode displays a near Nernstian slope (-57.8 mV decade-1) over a wide concentration range of 1 x 10(-7)-1 x 10(-1) M of SCN- ion. The electrode has a detection limit of 4.8 x 10(-8) M (2.8 ng/cm3) SCN- and shows response times of about 15 s and 120 s for low to high and high to low concentration sequences, respectively. The proposed sensor shows high selectivity towards SCN- over several common organic and inorganic anions. The electrode revealed a great enhancement in selectivity coefficients and detection limit for SCN-, in comparison with the previously reported electrodes. It was successfully applied to the direct determination of SCN- in milk and biological samples, and as an indicator electrode in titration of Ag+ ions with thiocyanate.     

Thiocyanate ion-selective PVC membrane electrode based on N,N'-ethylene-bis(4-methylsalicylidineiminato)nickel(II).

A highly selective poly(vinyl chloride) (PVC) membrane electrode based on an N,N'-ethylene-bis(4-methyl-salicylidineiminato) nickel(II) [Ni(EBMSI)] complex as a carrier for a thiocyanate-selective electrode is reported. The influences of the membrane composition, pH and possible interfering anions were investigated based on the response properties of the electrode. The electrode exhibited a good Nernstian slope of -58.9 +/- 0.7 mV decade(-1), over a wide pH range of 3.5 - 8.5 and a linear range of 1.0 x 10(-6) - 1.0 x 10(-1) M for thiocyanate. The detection limit of electrode was 3.1 x 10(-7) M SCN(-). The selectivity coefficients determined by a fixed interference method (FIM) indicate that a good discriminating ability towards the SCN- ion compared to other anions. The proposed sensor had a fast response time of about 5 - 15 s and could be used for at least 3 months without any considerable divergence in the potential. It was applied as an indicator electrode in the titration of thiocyanate with Ag+ and in the potentiometric determination of thiocyanate in saliva and urine samples.     

Indirect Determination of Sulfide by Extraction Flotation Spectrophotometry of Copper(II) with Ammonium Sulfate‐Ethanol‐Water System

A new extraction flotation spectrum method for indirect determination of trace amounts of sulfide by ammonium sulfate‐ethanol‐water system was developed. It showed that Cu(II) could combine with S^2? into precipitate (CuS) which was floated in the surface of ethanol and water in the presence of ammonium sulfate. The sulfide can be indirectly determined by determining the flotation yield of Cu(II). The linear range from 2.4 × 10^?8to 3.2 × 10^?6g/mL and the detect limit of 2.0 × 10^?8g/mL was achieved. The results showed the determination of S^2? was not affected by Pb(II), Zn(II), Cd(II), Fe(II), Co(II),Ni(II), Mn(II) and Cl^?, Br^?, I^?, etc. In the paper, the method was successfully applied to the determination of a trace amount of sulfide in polluted water samples with the advantages of simplicity of equipment, rapidity, low cost, etc.     

Kinetic determination of thiocyanate on the basis of its catalytic effect on the oxidation of methylene blue with potassium bromate.

This study reports a sensitive kinetic spectrophotometric method for the determination of trace amounts of thiocyanate. In acidic solution, Methylene Blue (MB) is oxidized by bromate to form a colorless compound. The reaction is accelerated by trace amounts of thiocyanate and can be followed by measuring the absorbance at 664 nm. The absorbance of the reaction decreased with an increase in the reaction time. Under the optimum experimental conditions (0.56 M of sulfuric acid, 3.9 x 10(-5) M of MB, 3.0 x 10(-3) M of bromate, 180 s, 25 degrees C), thiocyanate can be determined in the range 5.0 - 180 ng/ml. The relative standard deviations (n = 8) are 2.81 and 1.43% for 10.0 and 150 ng/ml thiocyanate, respectively. The detection limit of this method is (3sigma) 3.8 ng/ml. This method was successfully applied to the determination of thiocyanate in real samples.     

Indirect determination of cefradine with n-propyl alcohol–ammonium sulfate–water system by extraction–flotation of cuprous thiocyanate

A new method was developed for the determination of cefradine by extraction-flotation of CuSCN. The experiment indicated that in the presence of 0.20 mol/L NaOH the degradation of cefradine took place in water bath at 100 ℃. The thiol group （-SH） of the degradation product could reduce Cu（Ⅱ） to Cu（Ⅰ） for the formation of the emulsion CuSCN in the presence of NH4SCN at pH 4.0. By determining the residual amount of Cu（Ⅱ） in the solution and calculating the flotation yield of Cu（Ⅱ）, the indirect determination of cefradine can be obtained. This method has been applied to determine cefradine in capsules, human serum and urine samples, respectively.     

Extraction of manganese(II) with dithizone and potassium thiocyanate on foam sorbents for spectrophotometric determination in silicates

A method for selective extraction of Mn(II) with dithizone and potassium thiocyanate has been described. The method involves formation of a Mn(II)-thiocyanate-dithizone complex in a hexamine medium containing potassium thiocyanate (2.8M), dithizone (5.5-6.5 x 10(-5)M) and hydroxylamine hydrochloride (0.25%) at pH approximately 6 followed by extraction of the complex on polyurethane foam using batch squeezing mode within 1 hr. The sorbed Mn-thiocyanate-dithizone complex is eluted with acetone and made alkaline with 0.5 ml of a stabilizer solution (19 ml 2M NH(3) solution + 1 ml 5% hydroxylamine hydrochloride). The absorbance of the solution is measured at 506 nm. The adverse effect due to Pb may be obviated by separating the Pb as the sulphate during decomposition of sample and that due to iron may be removed before extraction of Mn by any suitable method. The other interfering elements (Cd, Zn, Ni, Co, Cu, etc.) are masked with KCN (6 x 10(-3)M optimum) solution. The method obeys Beer's Law from 0.1 to 2.0 mug Mn/ml. The method has been applied to various silicates, carbonates and glasses.     

Determination of trace amounts of the flotation collectors ethyl xanthate and diethyl dithiophosphate in aqueous solutions by cathodic stripping voltammetry

A cathodic stripping method has been devised for determination of low concentrations of the flotation collectors ethyl xanthate, diethyl dixanthogen and diethyl dithiophosphate. The limit of detection for ethyl xanthate was 1 x 10(-8)M by the differential pulse technique and with deposition for 2 min at -0.1 V. Three peaks were observed, each increasing in different concentration ranges of ethyl xanthate. A reaction mechanism is proposed. The detection limit for diethyl dithiophosphate was 1 x 10(-7)M by the differential pulse technique and with deposition for 3 min at -0.1 V. The analytical method was applied to determine ethyl xanthate in a sulphide mineral flotation plant and the amount of adsorbed ethyl xanthate and diethyl dithiophosphate on Cu(2)S. It was found that the adsorbed ethyl xanthate forms nearly a monolayer on Cu(2)S and that the amount of adsorbed diethyl dithiophosphate corresponds approximately to 0.4 monolayer.     

Anion selective polymeric membrane electrodes based on cyclopalladated amine complexes

The potentiometric anion selectivity of two polymer membrane based electrodes (I and II) formulated with two new cyclopalladated amine complexes as the active components are examined. The electrodes exhibit a non-Hofmeister selectivity pattern with a significantly enhanced response towards thiocyanate, iodide and nitrite. The graph potential versus log c is linear over the concentration range 10(-6)-6x10(-2) M thiocyanate with electrode I and 10(-6)-10(-3) M with electrode II; 10(-5)-10(-2) M iodide with electrode I and 10(-3)-6x10(-2) M with electrode II; and 10(-3)-6x10(-2) M nitrite with both electrodes. The influence of the plasticizer and pH are studied. The potentiometric selectivity coefficients for I, II and blank membrane electrodes are reported. The selective interaction between Pd(II) thiocyanate, iodide and nitrite is postulated to be the reason for its higher response.     

Preparation of ethambutol-copper(II) complex and fabrication of PVC based membrane potentiometric sensor for copper

Copper(II) complex of ethambutol (I) was prepared and used in the fabrication of Cu(2+) selective ISE membrane. The membrane having Cu(II)-ethambutol complex (I) as electroactive material, along with sodium tetraphenylborate (NaTPB) as anion discriminator, dioctylphthalate (DOP) as plasticizer in poly(vinyl chloride) (PVC) matrix in the percentage ratio 6:2:190:200 (I:NaTPB:DOP:PVC) (w/w) gave a linear response in the concentration range 7.94x10(-6) to 1.0x10(-1) M of Cu(2+) with a slope of 29.9+/-0.2 mV per decade of activity and a fast response time of 11+/-2 s. The sensor works well in the pH range 2.1-6.3 and could be satisfactorily used in presence of 40% (v/v) methanol, ethanol and acetone and is selective for copper over a large number of cations with slight interference from Na(+) and Co(2+) if present at a level 1.5x10(-5) and 6.5x10(-5) M, respectively. It works well over a period of 6 months and can also be used as indicator electrode for the end point determination in the potentiometric titration of Cu(2+) against EDTA as well as in the determination of Cu(2+) in real samples.     

Simultaneous determination of Cu(II) and Ag(I) on SP Sephadex C25 as complexes with 1-phenyl-1,2-propanedione-2-oximethiosemicarbazone by derivative spectrophotometry

A simple, rapid, and sensitive method has been developed for the simultaneous determination of trace amounts of copper and silver using 1-phenyl-1,2-propanedione-2-oximethiosemicarbazone (PPDOT) as a chromogenic reagent. The proposed method was based on retention and preconcentration of the complexes Cu(III)-PPDOT and Ag(I)-PPDOT on a solid phase in acid medium. The complexes were quantitatively retained in the cation exchanger SP Sephadex C25, and the analytical measurements were executed directly in the solid phase by derivative spectrophotometry. In this simultaneous determination, the second derivative and the zero crossing method were used. The determination of copper and silver was carried out to 321.0 and 427.0 nm, respectively. In order to obtain quantitative recoveries of the metal ions, various experimental analytical parameters, such as pH, stirring time, volume, and amount of solid phase, were optimized. The effect of interfering ions on the determination was described. The recovery values for Cu(II) and Ag(I) were found to be > 98%, and the relative standard deviation was < or = 2%. The detection limits (3sigma criterion) for Cu(II) and Ag(I) were found to be 0.9 x 10(-8) and 13 x 10(-8) M, respectively. The developed method was utilized for preconcentration and determination of Cu(II) and Ag(I) in industrial effluents and natural water samples. The results were consistent with those provided by inductively coupled plasma/mass spectrometry.     

Voltammetric study of the redox behaviour of the Hg(II)/Hg(I)/Hg system at a rotating metal-ring/glassy-carbon disc electrode

The reduction of Hg(II) at a glassy-carbon electrode in various electrolytes has been studied by rotating ring-disc voltammetry. Reduction proceeds directly to metallic mercury in a single 2-electron step. However, at the foot of the wave, and only during the first reduction sweep after pretreatment of the electrode surface, a small amount of Hg(I) species is detected at the ring. The appearance of an Hg(I) intermediate is most pronounced in sulphuric acid solution. The reduction of Hg(II) is found to proceed irreversibly and to be of first order. At sufficiently negative potentials the reduction is convective-diffusion controlled. Stripping voltammetric experiments indicate that the dissolution of mercury gives Hg(II) in complexing electrolytes. In non-complexing electrolytes the initially formed Hg(II) reacts with mercury atoms on the electrode surface to give Hg(I). During electrodissolution, two stripping peaks may be observed as a result of underpotential adsorption of mercury on glassy carbon. The difference in peak potential between the adsorption (mono) layer peak and the bulk mercury peak has been related to the difference in work functions of the deposit (mercury) and substrate (carbon). A rotating glassy-carbon electrode has been used for the anodic stripping determination of mercury. When an appropriate amount of a cation such as cadmium(II) or copper(II) is added to the test solution, mercury down to 2 x 10(-9)M (0.4 ng ml ) can be determined in acidified thiocyanate electrolyte with a relative standard deviation of about 22%.