Direct detection of explosives on solid surfaces by mass spectrometry with an ambient ion source based on dielectric barrier discharge

Trace amounts of explosives on solid surfaces were detected by mass spectrometry at ambient conditions with a new technique termed dielectric barrier discharge ionization (DBDI). By the needle-plate discharge mode, a plasma discharge with energetic electrons was generated, which could launch the desorption and ionization of the explosives from solid surfaces. Hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), 2,4,6-trinitrotoluene (TNT), and pentaerythritol tetranitrate (PETN) were desorbed directly from the explosives-contaminated surface by DBDI, forming the typical anions of [TNT](-), [TNT - H](-), [RDX + NO(2)](-), [PETN + ONO(2)](-), and [RDX + ONO(2)](-). The ions were transferred into the MS instrument for analysis in the negative ion mode. The detection limit of present method was 10 pg for TNT (m/z 197, S/N 8 : 1), 0.1 ng for RDX (m/z 284, S/N 10 : 1), and 1 ng for PETN (m/z 260, S/N 12 : 1). The present method allowed the detection of trace explosives on various matrices, including paper, cloth, chemical fiber, glass, paints, and soil. A relative standard deviation of 5.57% was achieved by depositing 100 pg of TNT on these matrices. The analysis of A-5, a mixture of RDX and additives, has been carried out and the results were consistent with the reference values. The DBDI-MS method represents a simple and rapid way for the detection of explosives with high sensitivity and specificity, which is especially useful when they are present in trace amounts on ordinary environmental surfaces.     

A fast method for monitoring of organic explosives in soil: a gas temperature gradient approach in LC–APCI/MS/MS

A novel, fast liquid chromatography atmospheric pressure chemical ionization mass spectrometry (LC–APCI–MS/MS) screening method was developed to determine the trace amounts of TNT (trinitrotoluene), RDX (1,3,5-trinitroperhydro-1,3,5-triazine), HMX (cyclotetramethylene-tetranitramine), PETN (pentaerythritoltetranitrate), TETRYL (2,4,6-trinitrophenyl-N-methylnitramine), picric acid (2,4,6 trinitrophenol), 2,6-DNT (2,6-dinitrotoluene), and TMETN (trimethylolethane-trinitrate) which contaminate the soil after explosion. A gradient of 2.00 mM ammonium nitrate aqueous solution-methanol mobile system, C18 column, and atmospheric pressure chemical ionization (APCI) (?) ionization mode was used after a single-step solid–liquid extraction procedure from soil matrix. Phenytoin was used as the internal standard. As an extraordinary application, gas temperature gradient in an APCI ionization was used. Analytes were selectively eluted from the system within 10 min. Average recovery obtained from the soil was between 93.01 and 104.20% at 250.0, 500.0, and 1000.0 ngg^?1 concentration levels. Limit of detection (LOD) and limit of quantification (LOQ) values obtained from the analysis of the soil samples including explosive mix were between 8.9–161.2 and 13.2–241.5 ngg^?1, respectively.     

Quantitative calibration of vapor levels of TNT, RDX, and PETN using a diffusion generator with gravimetry and ion mobility spectrometry

A prototype generator for creating a continuous stream of explosive vapor was referenced quantitatively both to a standard weight from the National Institute of Standards and Technology (NIST) and to the response of an ion mobility spectrometer. Vapors from solid explosive, in a precision bore glass tube at constant temperature, diffuse into an inert gas flow. Mass output rates were determined by (1) sample temperature, and (2) sample tube dimensions (length and cross-sectional area). A reference to NIST was achieved gravimetrically though a microbalance calibrated with a reference weight; mass output rates were obtained for 2,4,6-trinitrotoluene (TNT), cyclotrimethylenetrinitramine (RDX) and pentaerythritol tetranitrate (PETN) at three or more oven temperatures between 79 degrees C and 150 degrees C. The mass output rate was stable over hundreds of hours of continuous operation and the output was adjustable from a few picograms per second to several nanograms per second through variation of the oven temperature. An independent calibration of the vapor generator for TNT at 79 degrees C using an ion mobility spectrometer matched exactly the gravimetric-based findings. In most instances, measured mass output rates compared favorably with theoretically calculated mass output rates, with discrepancies in a few cases resulting primarily from uncertainties in terms (vapor pressures and diffusion coefficients) used to perform the calculations. Agreement is generally not good for PETN, where molecular decomposition contributed to higher than expected measured mass outputs.     

Detection of explosives via photolytic cleavage of nitroesters and nitramines

The nitramine-containing explosive RDX and the nitroester-containing explosive PETN are shown to be susceptible to photofragmentation upon exposure to sunlight. Model compounds containing nitroester and nitramine moieties are also shown to fragment upon exposure to UV irradiation. The products of this photofragmentation are reactive, electrophilic NO(x) species, such as nitrous and nitric acid, nitric oxide, and nitrogen dioxide. N,N-Dimethylaniline is capable of being nitrated by the reactive, electrophilic NO(x) photofragmentation products of RDX and PETN. A series of 9,9-disubstituted 9,10-dihydroacridines (DHAs) are synthesized from either N-phenylanthranilic acid methyl ester or a diphenylamine derivative and are similarly shown to be rapidly nitrated by the photofragmentation products of RDX and PETN. A new (turn-on) emission signal at 550 nm is observed upon nitration of DHAs due to the generation of fluorescent donor-acceptor chromophores. Using fluorescence spectroscopy, the presence of ca. 1.2 ng of RDX and 320 pg of PETN can be detected by DHA indicators in the solid state upon exposure to sunlight. The nitration of aromatic amines by the photofragmentation products of RDX and PETN is presented as a unique, highly selective detection mechanism for nitroester- and nitramine-containing explosives and DHAs are presented as inexpensive and impermanent fluorogenic indicators for the selective, standoff/remote identification of RDX and PETN.     

Photofragmentation of nitro-based explosives with chemiluminescence detection

A simple, fast, reliable, sensitive and potentially portable explosive detection device was developed employing laser photofragmentation (PF) followed by heterogeneous chemiluminescence (CL) detection. The PF process involves the release of NO_{x(x = 1,2)} moieties from explosive compounds such as TNT, RDX, and PETN through a stepwise excitation–dissociation process using a 193 nm ArF laser. The NO_{x(x = 1,2)} produced upon PF is subsequently detected by its CL reaction with basic luminol solution. The intensity of the CL signal was detected by a thermoelectrically cooled photomultiplier tube with high quantum efficiency and negligible dark current counts. The system was able to detect trace amounts of explosives in various forms in real time under ambient conditions. Detection limits of 3 ppbv for PETN, 2 ppbv for RDX, and 34 ppbv for TNT were obtained. It was also demonstrated that the presence of PETN residue within the range of 61 to 186 ng/cm² can be detected at a given signal-to-background ratio of 10 using a few microjoules of laser energy. The technique also demonstrated its potential for the direct analysis of trace explosive in soil. An LOD range of 0.5–4.3 ppm for PETN was established, which is comparable to currently available techniques. Figure Photofragmentation–chemiluminescence detector     

Low‐pressure barrier discharge ion source using air as a carrier gas and its application to the analysis of drugs and explosives

In this work, a low‐pressure air dielectric‐barrier discharge (DBD) ion source using a capillary with the inner diameter of 0.115 and 12 mm long applicable to miniaturized mass spectrometers was developed. The analytes, trinitrotoluene (TNT), 1,3,5‐trinitroperhydro‐1,3,5‐triazine (RDX), 1,3,5,7‐tetranitroperhydro‐1,3,5,7‐tetrazocine (HMX), pentaerythritol tetranitrate (PETN), nitroglycerine (NG), hexamethylene triperoxide diamine (HMTD), caffeine, cocaine and morphine, introduced through the capillary, were ionized by a low‐pressure air DBD. The ion source pressures were changed by using various sizes of the ion sampling orifice. The signal intensities of those analytes showed marked pressure dependence. TNT was detected with higher sensitivity at lower pressure but vice versa for other analytes. For all analytes, a marked signal enhancement was observed when a grounded cylindrical mesh electrode was installed in the DBD ion source. Among nine analytes, RDX, HMX, NG and PETN could be detected as cluster ions [analyte + NO₃]^? even at low pressure and high temperature up to 180 °C. The detection indicates that these cluster ions are stable enough to survive under present experimental conditions. The unexpectedly high stabilities of these cluster ions were verified by density functional theory calculation. Copyright © 2016 John Wiley & Sons, Ltd.     

Detection of explosives on skin using ambient ionization mass spectrometry

Single nanogram amounts of the explosives TNT, RDX, HMX, PETN and their mixtures were detected and identified in a few seconds on the surface of human skin without any sample preparation by desorption electrospray ionization (DESI) using a spray solution of methanol-water doped with sodium chloride to form the chloride adducts with RDX, HMX, and PETN while TNT was examined as the radical anion and tandem mass spectrometry was used to confirm the identifications.     

Low-mass ions observed in plasma desorption mass spectrometry of high explosives

The low-mass ions observed in both positive and negative plasma desorption mass spectrometry (PDMS) of the high explosives HMX, RDX, CL-20, NC, PETN and TNT are reported. Possible identities of the most abundant ions are suggested and their presence or absence in the different spectra is related to the properties of the explosives as matrices in PDMS. The detection of abundant NO+ and NO2- ions for HMX, RDX and CL-20, which are efficient matrices, indicates that explosive decomposition takes place in PDMS of these three substances and that a contribution from the corresponding chemical energy release is possible. The observation of abundant C2H4N+ and CH2N+ ions, which have high protonation properties, might also explain the higher protein charge states observed with these matrices. Also, the observation of NO2-, possibly formed by electron scavenging which increases the survival probability of positively charged protein molecular ions, completes the pattern. TNT does not give any of these ions and it is thereby possible to explain why it does not work as a PDMS matrix. For NC and PETN, decomposition does not seem to be as pronounced as for HMX, RDX and CL-20, and also no particularly abundant ions with high protonation properties are observed. The fact that NC works well as a matrix might be related to other properties of this compound, such as its high adsorption ability.     

Note on the use of the vacuum stability test in the study of initiation reactivity of attractive cyclic nitramines in Formex P1 matrix

The zero-order reaction rates (specific rate constants) of isothermal decomposition at 120 °C of plastic bonded explosives (PBXs) were measured by means of the Czech vacuum stability test, STABIL. The PBXs are based on 1,3,5-trinitro-1,3,5-triazinane (RDX), 1,3,5,7-tetranitro-1,3,5,7-tetrazocane (HMX), cis-1,3,4,6-tetranitro-octahydroimidazo-[4,5-d]imidazole (BCHMX), and ε 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (ε-HNIW, ε-CL-20) with 13 wt% of the Formex P1 type matrix, i.e., a matrix of the explosive with pentaerythritol tetranitrate (PETN) bound by 13 wt% of a mixture of 25 wt% of styrene–butadiene rubber and 75 wt% of an oily material. Dependencies were found between the specific rate constants mentioned and the detonation velocities of PBXs, and consequently between these constants and the impact and electric spark sensitivities of pure explosive fillers, i.e., RDX, HMX, HNIW, BCHMX, and PETN. It is stated that the higher impact or electric spark sensitivity of their pure explosive fillers corresponds to the higher thermal reactivity of the given PBXs.     

Micellar extraction and high performance liquid chromatography-ultra violet determination of some explosives in water samples

An analytical method based on the cloud point extraction combined with high performance liquid chromatography is used for the extraction, separation and determination of four explosives; octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazine (HMX), hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), 2,4,6-trinitrotoluene (TNT) and pentaerythritol tetranitrate (PETN). These compounds are extracted by using of Triton X-114 and cetyl-trimethyl ammonium bromide (CTAB). After extraction, the samples were analyzed using a HPLC-UV system. The parameters affecting extraction efficiency (such as Triton X-114 and CTAB concentrations, amount of Na₂SO₄, temperature, incubation and centrifuge times) were evaluated and optimized. Under the optimum conditions, the preconcentration factor was 40 and the improvement factors of 34, 29, 61 and 42 with detection limits of 0.09, 0.14, 0.08 and 0.40 (μg L⁻¹) were obtained for HMX, RDX, TNT and PETN, respectively. The proposed method was successfully applied to the determination of these compounds in water samples and showed recovery percentages of 97-102% with RSD values of 2.13-4.92%.     

Selective sampling with direct ion mobility spectrometric detection for explosives analysis

This study investigates the potential and limitations of a field-deployable analytical approach that involves selective capture of explosive materials with direct analysis by ion mobility spectrometry (IMS). Selective capture of explosives was performed on deactivated quartz fiber filters impregnated with metal β-diketonate polymers. These Lewis acidic polymers selectively interact with Lewis base analytes such as explosives. The filters were directly inserted into an IMS instrument for analysis. The uptake kinetics of 2,4,6-trinitrotoluene (TNT) from a saturated atmosphere were characterized, and based on these studies, passive equilibrium sampling was applied to estimate the TNT concentration within an ammunition magazine that contained bulk TNT. Hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) uptake from a saturated environment also was examined over a one-month period. Each incremental sampling period showed increasing quantities of RDX culminating with collection of approximately 5 ng of RDX on the filter at the end of one month. This is the first time that gas-phase uptake of RDX has been demonstrated.     

Analysis of 2,4,6-trinitrotoluene, pentaerythritol tetranitrate and cyclo-1,3,5-trimethylene-2,4,6-trinitramine using negative corona discharge ion mobility spectrometry

In this study, the capability of negative corona discharge ion mobility spectrometry (IMS) for quantitative magnitude of several explosives including 2,4,6-trinitrotoluene (TNT), pentaerythritol tetranitrate (PETN) and cyclo-1,3,5-trimethylene-2,4,6-trinitramine (RDX) has been evaluated for the first time. The total current obtained with the negative corona discharge was about 100 times larger than that of IMS based on ⁶³Ni, which results in a lower detection limit and a wider linear dynamic range. The detection limits for PETN, TNT and RDX were 8×10⁻¹¹, 7×10⁻¹¹ and 3×10⁻¹⁰ g, respectively. The calibration plots for these explosives showed linear dynamic ranges of about four orders of magnitude.     

Orthogonal Detection of Nitroaromatic Explosives via Direct Voltammetry Coupled to Enzyme‐Mediated Biocatalysis

This article describes a rapid and reliable electrochemical/enzymatic method of verifying the presence of nitroaromatic explosives. The new technique leverages both conventional voltammetric analysis and biocatalytic conversion of TNT. The simultaneous use of independent measurement schemes, based on two distinct processes, dramatically increases the information content and offers substantially improved reliability while minimizing the occurrence of false alarms. This has been accomplished by coupling direct voltammetric analysis with the biocatalytic conversion of the TNT substrate via nitroreductase (NR), which reduces a nitro group of TNT using NADH as an electron donor. This chemical reduction (30 s timescale) can then be observed using square‐wave voltammetry by examination of the reductive and oxidative features. This novel protocol was found to be selective for TNT, not only when compared to DNT and NT, but also to other explosive species such as RDX and PETN. This unique dual‐mode detection strategy for measuring TNT at a single device holds considerable promise for improving the probability of explosive detection and hence for diverse security screening applications.     

Thermal Analysis of Binary Systems. Explosive – lead compound

The thermal decomposition of explosives: pentaerythrol tetranitrate (PETN), 2,4,6-trinitrotoluene(TNT), cyclo-1,3,5-trimethylene-2,4,6-trinitroamine (RDX) and their two-component mixtures with 40% of lead compounds [PbO, Pb₃O₄, Pb(NO₃)₂] were performed. The simple method of determination of stability changes in the mixtures described above, in comparison with pure explosives was presented. The lead oxides accelerated significantly the thermal decomposition of explosives. Pb(NO₃)₂ acts as a catalyst in the mixture containing TNT degradation, but not in a case of PETN and RDX. This revised version was published online in August 2006 with corrections to the Cover Date.     

Direct exposure chemical ionization mass spectra of explosives

Mass spectra of explosives, including TNT, tetryl, nitroglycerin, PETN and RDX have been recorded by direct exposure chemical ionization with isobutane as reagent at source temperatures of 50–100°C. The mass spectra contain major [MH]⁺ ions, adduct ions and some fragment ions. The configuration of the relative abundances of these ions has been found to be a function of temperature and source pressure. Maximum [MH]⁺ ion abundance has been obtained at source pressures much lower than normal chemical ionization pressures.     

The very far-infrared spectra of energetic materials and possible confusion materials using terahertz pulsed spectroscopy

We have measured the terahertz absorption spectra of 1,3,5-trinitro-1,3,5-triazacyclohexane (RDX), pentaerythritol tetranitrate (PETN), 1,3,5,7-tetranitro-1,3,5,7-tetrazacyclooctane (HMX), 2,4,6-trinitrotoluene (TNT), the plastic explosives Semtex H, SX2, and Metabel, and a number of confusion materials using terahertz pulsed transmission spectroscopy. Spectral fingerprints were obtained from 3 to 133 cm⁻¹. The spectra of the plastic explosives are dominated by the spectral signatures of their explosive components due to low frequency vibrations and crystalline phonon modes. Importantly, the terahertz spectra of the confusion materials show no resemblance to the explosives spectra. The refractive indices obtained for the plastic explosives and confusion materials allowed us to derive reflectance spectra, which appear distinct and so suggest that terahertz reflection spectroscopy is a suitable tool for the detection of concealed explosives in security applications.     

Negative-Ion formation in the explosives RDX,PETN, and TNT by using the reversal electron attachment detection technique

First results of a beam-beam, single-collision study of negative-ion mass spectra produced by attachment of zero-energy electrons to the molecules of the explosives RDX, PETN, and TNT are presented. The technique used is reversal electron attachment detection (READ) wherein the zero-energy electrons are produced by focusing an intense electron beam into a shaped electrostatic field which reverses the trajectory of electrons. The target beam is introduced at the reversal point, and attachment occurs because the electrons have essentially zero longitudinal and radial velocity. The READ technique is used to obtain the “signature” of molecular ion formation and/or fragmentation for each explosive. Present data are compared with results from atmospheric-pressure ionization and negative-ion chemical ionization methods.     

Neutral desorption using a sealed enclosure to sample explosives on human skin for rapid detection by EESI-MS

A novel air-tight neutral desorption enclosure has been fabricated to noninvasively sample low picograms of explosives 2,4,6-trinitrotoluene (TNT), hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), octahydro-1,3,5,7-tetranitro-1,3,5,7-tetraazocine (HMX), triacetone triperoxide (TATP), and nitroglycerin (NG) from human skin using a neutral nitrogen gas beam. Without further sample pretreatment, the explosive mixtures collected from the skin surface were directly transported by a nitrogen carrier gas over a 4-m distance for sensitive detection and rapid identification by extractive electrospray ionization tandem mass spectrometry.     

In Situ Explosive Detection Using a Miniature Plasma Ion Source and a Portable Mass Spectrometer

A small low-temperature plasma (LTP) ionization probe was coupled to a portable mass spectrometer for the rapid detection of trace explosives on surfaces. Using only a small diaphragm pump to supply ambient air to the LTP source, 100 ng each of pentaerythritol tetranitrate (PETN), 1,3,5-trinitroperhydro-1,3,5-triazine (RDX), and 2,4,6-trinitrophenylmethylnitramine (Tetryl) were detectable on glass in under 1 minute. The main ion signal from these molecules (M) is the [M + NO₃]^? species. While much optimization remains, it is believed that this miniature LTP source will remove the need for external gas cylinders and additional heating for in situ explosives detection using portable mass spectrometers.     

Voltammetric determination of nitroaromatic and nitramine explosives contamination in soil

The contamination of soil by nitroaromatic and nitramine explosives is widespread during the manufacture, testing and disposal of explosives and ammunitions. The analysis for the presence of trace explosive contaminants in soil becomes important in the light of their effect on the growth of different varieties of plants and crops. 2,4,6-Trinitrotoluene (TNT), cyclotrimethylene trinitramine (Research Department explosive, RDX) and cyclotetramethylene tetranitramine (high melting point explosive, HMX), other related explosive compounds and their by-products must be monitored in soil and surrounding waterways since these are mutagenic, toxic and persistent pollutants that can leach from the contaminated soil to accumulate in the food chain. In this study, a voltammetric method has been developed for the determination of explosive such as RDX, HMX and TNT. The electrochemical redox behavior of RDX, HMX and TNT was studied through cyclic voltammetry and quantitative determination was carried out by using square wave voltammetry technique. Calibration curves were drawn and were linear in the range of 63-129 ppm for RDX with a detection limit of 10 ppm, 49-182 ppm for HMX with a detection limit of 1 ppm and 38-139 ppm for TNT with a detection limit of 1 ppm. This method was applied to determine the contaminations in several soil samples that yielded a relative error of 1% in the concentrations.