CeO2纳米晶包裹碳纳米管修饰电极对特布他林的电催化测定

制备出CeO2纳米晶包裹碳纳米管修饰玻碳电极,并运用循环伏安法、交流阻抗谱探讨了该电极的电化学特性。研究了特布他林在该修饰电极上的直接电化学行为。实验结果表明,特布他林在该修饰电极上具有良好的电流响应,与裸玻碳电极相比在pH 7.0缓冲溶液中氧化峰电位负移314 mV。采用计时电流法测定特布他林,其氧化峰电流与浓度在5.0×10-7~1.0×10-4mol/L范围呈良好线性关系,线性方程为:Ip(μA)=4.952-0.04724c(μmol/L),线性相关系数为0.9920,检出限为5.0×10-8mol/L(信噪比为3)。该电极已用于特布他林片剂中特布他林的测定。     

镍纳米粒子-离子液体修饰碳糊电极的制备及其对多巴胺的测定

制备了镍纳米粒子-离子液体修饰电极,在0.1 mol/L磷酸缓冲溶液(pH 6.0)中研究了多巴胺(DA)在修饰电极上的电化学行为.与裸电极相比,DA在该修饰电极上的氧化还原电位明显降低,氧化还原反应的峰电流明显增大,DA的峰电流与其浓度在2.0×10~(-8) ～1.0×10~(-4) mol/L范围内呈良好的线性关系,检出限为6.5×10~(-9) mol/L.该修饰电极对抗坏血酸具有明显的抗干扰能力.     

一种基于乙炔黑/壳聚糖膜修饰电极的对氨基酚传感研究

制备了一种乙炔黑/壳聚糖薄膜修饰的玻碳电极,用循环伏安法详细研究了对氨基酚在该修饰电极上的电化学行为.结果表明: 对氨基酚在此膜修饰电极上呈现出一对可逆的氧化还原峰.相对于裸玻碳电极,该氧化还原峰的峰电流明显提高,峰电位差减小,可逆性变好,表明乙炔黑/壳聚糖薄膜电极对对氨基酚的电化学氧化具有良好的催化作用.对氨基酚的氧化峰电流与其浓度在1.0×10-7～2.0×10-6 mol/L和2 0×10-6～5.0×10-4 mol/L范围内均呈良好的线性关系; 检出限为5.0×10-8 mol/L(S/N=3).应用此修饰电极测定实际水样,结果较满意.     

介孔炭/纳米金修饰玻碳电极的制备及其应用研究

制备了介孔炭/纳米金修饰玻碳电极,并对对苯二酚(HQ)在该修饰电极上的电化学行为进行了研究。与HQ在纯介孔炭材料修饰玻碳电极上的电化学响应相比,HQ在该修饰电极上的氧化峰和还原峰电流均大大增加,表明纳米金与介孔炭复合后对HQ具有良好的催化作用。HQ在该修饰电极上经过富集后,峰电流明显增大。采用循环伏安法对HQ电化学行为进行研究,结果表明,HQ在3.0×10-8~1.0×10-6mol/L和1.0×10-6~1.0×10-4mol/L浓度范围内与峰电流呈良好的线性关系,据此建立了检测HQ的电化学分析方法。该方法的相对标准偏差为0.69%,检出限(S/N=3)为1.0×10-8mol/L,具有较高的稳定性和灵敏度。     

二茂铁-离子液体修饰碳糊电极的研制

以室温离子液体N-辛基吡啶六氟磷酸盐为粘合剂与二茂铁和石墨粉相混合制备了一种新型二茂铁-离子液体修饰碳糊电极。以该电极为工作电极,采用循环伏安法、计时安培法研究了多巴胺(DA)在该糊电极上的电化学行为。实验结果表明:该电极在pH 5.0的乙酸-乙酸钠缓冲溶液中,外加电压0.8 V条件下,灵敏度最高。电流增量与DA浓度在1.0×10-5～1.0×10-3 mol/L范围内呈良好的线性关系,检出限为5.0×10-6 mol/L(S/N=3)。     

基于石墨烯修饰电极测定蔬菜中残余对硫磷的研究

制备了石墨烯薄膜修饰玻碳电极,并通过循环伏安法研究了对硫磷(PT)在该修饰电极上的电化学行为。对支持电解质、溶液pH值等实验条件进行了优化。结果表明,在0.1mol/L的乙酸-乙酸钠缓冲溶液(pH=5.0)中,PT在石墨烯薄膜修饰电极上具有良好的电化学响应,对比裸玻碳电极,PT的氧化峰峰电流显著提高,表明修饰膜对PT的电化学氧化具有一定的催化作用。PT的氧化峰电流及其浓度分别在1.0×10-7~1.0×10-6 mol/L范围内和3.0×10-6~1.0×10-5 mol/L范围内呈良好的线性关系,线性相关系数分别是0.9956和0.9874,检出限为1.0×10-8 mol/L。将该修饰电极应用于小白菜中残留PT的测量,结果比较满意。     

抗坏血酸在β-环糊精/二茂铁甲酸修饰电极上的电化学行为及测定

利用主客体化学反应将二茂铁甲酸包络在β-环糊精聚合物的空穴中,用新鲜蛋清作交联剂制成β-环糊精聚合物/二茂铁甲酸化学修饰玻碳电极,用电化学阻抗法和循环伏安法研究了修饰电极的电化学性能。在pH 7.0的磷酸盐缓冲溶液中,该修饰电极对抗坏血酸的电化学氧化有很好的催化活性,氧化峰电流与其浓度在6.2×10-6~5.0×10-3mol/L范围内呈良好的线性关系,线性回归方程为ip=0.4375+0.0301C(ip:μA,C:μmol/L),相关系数r=0.9982,检出限为1.0×10-6mol/L。抗坏血酸和多巴胺在修饰电极上于不同的电位(ΔE=490 mV)被氧化,可用于多巴胺存在下选择性测定抗坏血酸。     

NO2-在CTMAB-碳纳米管修饰电极上的电化学行为及测定

制备了十六烷基三甲基溴化铵-多壁碳纳米管修饰电极.用循环伏安法和示差脉冲伏安法研究了NO2 -在该修饰上的电化学行为,该修饰电极对NO2 -的氧化具有良好的电催化能力,NO2 -的氧化峰电流与其浓度在1.67×10-7 ～2.2×10 -5mol/L范围内呈现良好的线性关系,检测限为5.6×10-8mol/L(S/N=...     

酪氨酸在聚5-磺基水杨酸/多壁碳纳米管修饰电极上的电化学行为及其测定

用不同方法制备了四种修饰电极,酪氨酸在聚5-磺基水杨酸/多壁碳纳米管电极上的电化学响应明显优于裸玻碳电极和其他修饰电极.运用多种电化学方法研究了酪氨酸在电极上的电化学行为,结果表明:酪氨酸在电极上的反应是电子数和质子数均为1的扩散控制的不可逆氧化过程,氧化峰电流与酪氨酸的浓度在9.0×10-6～2.0×10-4mol/L的范围内呈良好的线性关系,IP(A)=-1.61×10-9-2.54×10-4c(mol/L),相关系数R=-0.9950,检出限为6.0×10-6mol/L.平均回收率为99.53％.     

普鲁士蓝/多壁碳纳米管修饰电极测定维生素C

利用电化学方法在多壁碳纳米管修饰的玻碳电极表面聚合一层普鲁士蓝,制备普鲁士蓝/多壁碳纳米管修饰玻碳电极,运用循环伏安法研究了维生素C(vc)在该修饰电极上的电化学行为.该修饰电极对Vc显示出快速的电化学响应和较好的电催化活性,在pH为4.0的磷酸盐溶液中,Ve浓度与其氧化峰电流在8.0×10-4～1.0×10-2 mol/L范围内呈现良好的线性关系,相关系数为0.9993,检测限为6.4×10-5mol/L.该电极具有较好的稳定性和重现性.     

Fluoride-selective electrode with internal redox reference electrode

The potential response of a symmetrical configuration in which the LaF₃-membrance is placed between two solutions is discussed. The electrode body provides contact with the inner surface of the fluoride membrane, with a solution containing Fe(CN) ₆ ^3– -Fe(CN) ₆ ^4– redox couple and a Pt wire as internal reference electrode. The electrode was examined in terms of potentialconcentration curves and potential-time response and shown to behave similarly to the commencal Orion fluoride electrode. The advantage of the proposed redox reference system is that the electrode has minimal drift immediately after assembly.     

Behaviour of the platinum electrode as a pH electrode

The platinum wire electrode behaves as a good pH electrode in the titration of 1.0 and 0.1N sulphuric or hydrochloric acid with the equivalent concentration of sodium hydroxide. The efficiency is greater when sulphuric acid is used. The end-points obtained are very close to those obtained with a glass-calomel system.     

Dodecyl benzene sulfonate anion-selective electrode based on polyaniline-coated electrode

A new dodecyl benzene sulfonate (DBS⁻) ion-selective electrode based on polyaniline is reported. The films of polyaniline doped with DBS⁻ were prepared electrochemically on platinum electrodes in the solution containing 1.0×10⁻³ M aniline and 7.0×10⁻³ M DBS⁻. The optimum potentiometric response was obtained for prepared polymeric film by passing electricity of 7.5 C cm⁻². The electrode exhibits an excellent Nernstian slope of −59.1±0.3 mV per decade for DBS⁻ ion over a wide concentration range (5.0×10⁻⁶ to 4.1×10⁻³ M) with a low detection limit (1.0×10⁻⁶ M). The proposed electrode revealed good sensitivities for DBS⁻ ion over a wide variety of other anions and can be used in the wide pH range of 5-10. It shows good stability, good reproducibility, wide range of pH independency and fast response (<20 s) without using internal solution. This electrode could be used for the determination of DBS⁻ in the real samples.     

Components of electrode polarization

It is shown that the electrode polarization is not the sum of the activation and concentration polarizations. Introducing the concepts of overvoltage of the process (deviation of the electrode potential from the thermodynamic value), of overvoltage of the reaction, a total concentration polarization, and a thermodynamic concentration polarization, the equations of these functions are derived and their properties examined.     

Determination of surface potentials from the electrode potentials of a single-crystal electrode

Determination of surface potentials Psi0 at the metal oxide/aqueous solution interface from measured electrode potentials of a metal oxide single-crystal electrode (SCrE) is described. The proposed method is based on the surface complexation model and evaluates the surface potential at the isoelectric point, i.e., at pHiep. This value is used for calculation of Psi0 values from the measured electrode potentials. Both 1-pK and 2-pK models produced the same result so that the procedure does not depend on the assumed mechanism of the surface charging. It is proposed to determine the pristine point of zero charge pHeln and the isoelectric point pHiep, and use these data to set the scale of surface potentials. The value of pHeln can be obtained at a sufficiently low ionic strength where pHpzc coincides with pHiep. The method is demonstrated on the example of the anatase single-crystal electrode. From the shifts of pHiep and pHpzc with respect to the pristine point of zero charge pHeln it was concluded that Cl- ions exhibit higher affinity for association with positively charged surface groups than ClO-4 ions. Also, preferential surface association of Na+ cations compared to both anions was detected. The slopes of the Psi0(pH) functions were found to be significantly lower in magnitude with respect to the Nernst equation, which is due to the high degree of counterion association at the surface caused by their relatively high concentration.     

The parathiocyanogen electrode

Stable, yellow anodic films of parathiocyanogen (SCN) _x were formed on a platinum electrode from 2.8 M KSCN in methanol at 45 °C at a constant current of 20–40 mA cm⁻² for 15–30 min. Loosely bound orange crystals of a more amorphous character were removed by rinsing to leave an adherent yellow film with sharp Raman bands under 647.1 nm laser excitation at 627 cm⁻¹ (vCS), 1152 cm⁻¹ and 1236–1261 cm⁻¹ (vNN and vCN). The lack of electroactivity and short-lived photocurrents pointed to an insulating film at potentials up to 1.0 V (SHE). At more positive potentials, longer-lasting photocurrents were obtained, consistent with breakdown of the insulating film. XPS scans confirmed N:C:S ratios close to 1:1:1, with a deficiency of S of some 10% due to S lost as sulfate at the film surface. Oxidation of SeCN⁻ in neutral aqueous solution led to the formation of a less-stable orange paraselenocyanogen film with a Raman band at 1256–1267 cm⁻¹, which decomposed within a day to grey selenium. Received: 12 December 1997 / Accepted: 23 March 1998     

Simulations of cyclic voltammetric and chronoamperometric electrode responses at a disk electrode using combinations of spherical and cylindrical electrode geometries

Using geometric models based on one-dimensional transport at spheres and cylinders, three methods for improving the simulation of voltammetric behavior of a disk electrode have been explored. One method is based on the common assumption of equivalency between the limiting currents for a disk and a hemisphere under steady-state diffusion conditions. The second method involves the use of a partial-sphere geometry which is a better approximation that is suitable at the extreme diffusional limits achievable at a disk electrode of fully planar and steady-state transport. The third method, which is generally applicable, is a further refinement that uses a combination of appropriate one-dimensional spherical and cylindrical geometries. The results demonstrate that reasonably accurate approximations of disk behavior for several reaction mechanisms can be achieved in a fraction of the time required to compute the more rigorous two-dimensional model. We propose that the approximation serve primarily as a fast way to explore system behavior and establish approximate values of the relevant parameters. More accurate computations can then be performed using the two-dimensional model.     

Immobilization of enzyme to platinum electrode and its use as enzyme electrode

A glucose electrode was fabricated by immobilizing glucose oxidase covalently onto a platinized platinum electrode. The sensor showed rapid response with response time of 2—4 s, and also the linear response to the glucose concentration, ranging from 2 x 10^-3 to 5 mM. The sensitivity was found to be correlated with the surface area of a base electrode used.     

Effect of electrode membrane surface ratio and thickness on lead electrode potential

Summary The lead ion selective electrode (ISE) consisting of PbS-Ag₂S is normally used with a membrane surface of outer layer areaA _o) and inner layer area (A _i) at unity (A _o=A _i). Partial covering of one surface area with an insulating material and keeping the other surface layer intact resulted in different ratios of membrane surface areas exposed to lead solutions. The potential linearly increased with increasing theA _o/A _i ratio and decreased with decreasing theA _o/A _i ratio. The lead ISE potential increased linearly with increasing the membrane thickness, but which required much longer time for a stable potential.

---

Wirkung von Oberflächenverhältnis und Dicke der Elektrodenmembran auf das Potential einer Bleielektrode

Zusammenfassung Die aus PbS-Ag₂S bestehende spezifische Bleiionen-Elektrode wird üblicherweise mit einem Oberflächenverhältnis der Außenfläche (A _o) und der Innenfläche (A _i) mitA _o=A _i verwendet. Durch teilweise Abdeckung einer Oberfläche mit isolierendem Material, ohne daß die andere Oberfläche verändert wird, ergaben sich verschiedene Verhältnisse der mit der Bleilösung in Berührung stehenden Oberflächen. Mit dem VerhältnisA _o/A _i stieg das Potential linear an bzw. es fiel mit diesem Verhältnis ab. Das Potential der spezifischen Bleielektrode stieg mit der Dicke der Membran, stabilisierte sich aber wesentlich langsamer.

     

Amperometric aspartate electrode

An amperometric enzyme electrode for L-aspartate determination was developed. The probe consisted of a platinum electrode which senses hydrogen peroxide produced from the reactions catalyzed by two enzymes co-immobilized on a preactivated polymeric membrane, α-Ketoglutarate in the presence of L-aspartate was transaminated to L-glutamate by aspartate aminotransferase and the glutamate produced was oxidized by glutamate oxidase, with concomitant production of hydrogen peroxide. Additional protective membranes eliminated interferences from glutamate and most electroactive compounds. The response curve of the probe was linear over the concentration range 1.0 × 10^?6 M to 2.0 × 10^?4 M aspartate and was useful for at least two months. Aspartic acid in some pharmaceutical products was determined and the results correlated well with a liquid chromatographic reference method and the manufacturer's specification.