Mo/HZSM-5丙烷芳构化催化性能及其吸附量热的研究

采用等量浸渍法制得一系列不同担载量的Ｍｏ／ＨＺＳＭ－５催化剂,运用ＸＲＤ和ＦＴＩＲ方法考察了Ｍｏ物种在催化剂表面的分散状态,首次采用微分吸一热技术对Ｍｏ／ＨｚＳＭ－５催化剂的表面酸性进行表征。同时研究了催化剂对丙烷芳构化的反应活性。结果表明：对于担载Ｍｏ的ＨＺＳＭ－５分子筛催化剂,Ｍｏ物种在ＨＺＳＭ－５分子筛表面上顺序为ＨＺＳＭ－５〉１％Ｍｏ／ＨＺＳＭ－５〉２％Ｍｏ／ＨＺＳＭ－５分子筛本身表面的酸     

高折光指数光学树脂的合成——相转移法合成不饱和硫醇酯单体的条件控制

采用正常的低温相转移催化（ＰＴＣ）和反滴碱溶液ＰＴＣ法分别合成了含硫双烯ＭＥＳＤＭＡ和单烯ＭＥＰＳＭＡ．１Ｈ ＮＭＲ分析证明ＭＥＳ中的杂质主要是由原料ＴＤＧ引入的．对含单个巯基的ＭＥＰＳ的正常ＰＴＣ酯化接枝双键，因存在巯基和不饱和双键的加成反应而导致失败．作者最终得到了折光指数在１６２５以上的ＭＥＳＤＭＡ／ＭＥＰＳＭＡ共聚物．     

中孔MCM—41分子筛在微孔沸石ZSM—5上附晶生长的研究

首次在微孔沸石ＺＳＭ５表面进行了ＭＣＭ４１分子筛的附晶生长，并首次提出中孔材料ＭＣＭ４１分子筛静电组配理论的新形式（ＸＳ＋Ｉ）；同时利用ＸＲＤ、ＴＥＭ、ＢＥＴ等测试手段表征了合成样品，并讨论了微孔沸石表面附晶生长中孔分子筛ＭＣＭ４１的合成化学，考察了Ｆ离子效应、ｐＨ值及表面活性剂ＣＴＡＢ（十六烷基三甲基溴化铵）的影响。     

新型甲烷无氧芳构化催化剂MoO3/MCM-49

自Ｂｅｎｎｅｔｔ[1]等合成出新型分子筛ＭＣＭ 4 9以来 ,有关其结构及性质研究的报道相对较少 .Ｂｅｎ ｎｅｔｔ[1]指出 ,ＭＣＭ 4 9在一些特殊的催化反应上表现出了比ＭＣＭ 2 2更高的活性 (如在丙烯无氧芳构化反应中 ,ＭＣＭ 4 9上丙烯的转化率为 7 1 6% ,远大于ＭＣＭ 2 2的 2 64% ) .ＭＣＭ 4 9的发现时间较晚 ,且合成相对困难 ,在一定程度上限制了对其性质的进一步研究 .对甲烷无氧芳构化催化反应的研究发现 ,酸性适当且具有交叉十元环孔道体系的分子筛载体表现出了较高的催化活性 .ＭＣＭ 4 9与ＭＣＭ 2 2均具有两套互不相通的交叉…     

单体极性对甲基丙烯酸甲酯/丙烯酸丁酯/甲基丙烯酸钠无皂乳液共聚合的影响

研究了少量甲基丙烯酸钠（ＮａＭＡ）存在下单体极性对甲基丙烯酸甲酯（ＭＭＡ）／丙烯酸丁酯（ＢＡ）无皂乳液共聚合的影响．单体极性降低，使粒径减小、聚合速率提高、乳液表面张力和粘度降低、粒子表面电荷密度增大、聚合物分子量提高．ＭＭＡ／ＮａＭＡ无皂乳液聚合物只呈现一个玻璃化温度Ｔｇ，ＢＡ／ＮａＭＡ无皂乳液聚合物呈现两个Ｔｇ，ＭＭＡ／ＢＡ比为２∶１～１∶２的ＭＭＡ／ＢＡ／ＮａＭＡ无皂乳液聚合物呈现四个Ｔｇ，这是由于粒子外面相对富含ＯＳＯ－３和ＣＯＯ－基聚合物的亚层溶解了较多的水，使ＢＡ向粒子中心扩散，ＭＭＡ向外扩散，造成组成差异和相分离而引起的．     

水解对MCM—41分子筛的结构破坏作用

详细考察了ＳｉＭＣＭ－４１、ＡｌＭＣＭ－４１和ＨＡＩＭＣＭ－４１在不同环境中的水结构破坏情况,空气和水蒸汽中短期高温焙烧对全硅型ＳｉＭＣＭ－４１的结构影响较小,但在潮湿空气中长期放置可因Ｓｉ－Ｏ－Ｓｉ键发生水解而造成结构的严重破坏,ＡｌＭＣＭ－４１的抗水解能力优于ＳｉＭＣＭ－４１的,但因其结构中包含一一定量的Ｎａ离子,降低了高温焙烧时结构的热稳定性和水热稳定性,ＨＡｌＭＣＭ－４１的热稳定性和水热稳     

高纯度中孔分子筛MCM—41的合成与表征

用不同ｐＨ值的混合制备了不同孔径的全硅ＭＣＭ－４１和不同金属离子取代的Ｍ－ＭＣＭ－４１（Ｍ－Ａｌ,Ｍｎ,Ｆｅ和Ｖ）分子筛。这些试样均呈现ＭＣＭ－４１的Ｘ射线粉末笛射特征峰和Ⅳ型氮气吸附等温线,但混有不同含量的无定形氧化硅。样品中ＭＣＭ－４１晶体的含量与溶胶的ｐＨ值和所用表面活性剂的碳链链长有关,骨架硅的金属离子取代降低了ＭＣＭ－４１的有序度,并且（１００）面衍射峰强度从Ａｌ到Ｖ依次减弱。     

水解对MCM-41分子筛的结构破坏作用

详细考察了ＳｉＭＣＭ－４１、ＡｌＭＣＭ－４１和ＨＡｌＭＣＭ－４１在不同环境中的水解和结构破坏情况．空气和水蒸汽中短期高温焙烧对全硅型ＳｉＭＣＭ－４１的结构影响较小,但在潮湿空气中长期放置可因Ｓｉ—Ｏ—Ｓｉ键发生水解而造成结构的严重破坏．ＡｌＭＣＭ－４１的抗水解能力优于ＳｉＭＣＭ－４１的,但因其结构中包含一定量的Ｎａ＋离子,降低了高温焙烧时结构的热稳定性和水热稳定性．ＨＡｌＭＣＭ－４１的热稳定性和水热稳定性均优于ＡｌＭＣＭ－４１．分子筛水热晶化过程中的盐析效应被证实是导致ＡｌＭＣＭ－４１和ＨＡｌＭＣＭ－４１抗水解能力增强的原因,因此在合成原料中加盐可显著改善ＭＣＭ－４１分子筛的抗水解能力和稳定性     

微型机电系统在物化分析中的应用

介绍了微型机电系统（ＭＥＭＳ）的基本概念，发展简史和主要特点。详细讨论了ＭＥＭＳ在化学分析中的应用，指出ＭＥＭＳ技术使化学分析仪器微小型化、性能提高，同时还降低了仪器和实验的成本。最后简要介绍了微小型化学分析仪器的支撑技术。     

系列线型[M2M‘S4O4]^2—簇的合成及光谱与结构的关系（M=Mo,W;M…

报道了６种线型簇合物（Ｅｔ４Ｎ）２（Ｍ２Ｍ＇Ｓ４Ｏ４）（Ｍ＝Ｍｏ，Ｗ；Ｍ＇＝ＣＯ，ＮＩ，Ｆｅ）的合成，通过对ＵＶ－Ｖｉｓ，ＩＲ及ＸＰＳ光谱的对比分析，讨论了簇阴离子（ＭＷＭ＇Ｓ４Ｏ４）＾２－中心金属Ｍ＇的ｄ电子结构、氧化态以及（Ｍ＇Ｓ４）的微环境，由此推了簇阴离子构型，并讨论了化合物的稳定性。     

Investigation of thermo-reversibility of polymer crosslinked by reversible covalent bonds through torque measurement

Brominated butyl rubber (BIIR) was crosslinked through an esterification reaction using the sodium salt of dicyclopentadiene dicarboxylic acid (DCPDCA) as crosslinking agent. The crosslinked BIIR could de-crosslink upon heating and re-crosslink upon cooling due to Diels-Alder type reversible de-dimerization/re-dimerization of dicyclopentadiene moieties in the rubber networks. Torque measurement of the crosslinked rubber was conducted at various temperatures using a typical curemeter to investigate the thermo-reversibility. It was revealed that proper temperature for thermal processing of the crosslinked BIIR would be around 174 °C, at which the crosslinked polymer exhibits good flowability and is not too high to induce unexpected side reactions. The torque measurement was also carried out to investigate the efficiency of antioxidant on retarding the loss of the thermo-reversibility of the crosslinked polymer during heating-cooling cycles. It was found that addition of antioxidant 2246 [2,2′-methylenebis(6-tert-butyl-4-methylphenol)] into BIIR could significantly improve the thermo-reversibility of DCPDCA crosslinked BIIR. Torque measurement provides a convenient and sensitive method to understand the thermal behavior of reversible covalent crosslinked polymer.     

Polymerization of bis(2-oxazoline) compounds with dicarboxylic acids

A side reaction was found in the reaction of a 2-oxazoline compound with a carboxylic acid. It is an oxazoline ring opening addition to an amide group formed by the main reaction. In addition, certain phosphites were found to act as catalyst for the side reaction. The rate constants of the main and side reactions in the system of 2-phenyl-2-oxazoline and n-octanoic acid were obtained through simulation of the reactions on an analog computer. The side reaction makes it impossible for a very high molecular weight polymer to form in the reaction of a bis-2-oxazoline with a dicarboxylic acid, but makes it possible for a new crosslinked polymer to form when excess bis-2-oxazoline and a dicarboxylic acid are heated in the presence of a certain phosphite.     

Effect of surface swelling on diffusion on polymers. II. Delamination

Swelling in chloroform resulted in delamination of surface-hydroxylated styrene-butadiene-styrene block copolymers, with the formation of three fractions: crosslinked gel, reacted sol, and unreacted chloroform-soluble material. From the relative weights of these fractions, the depth of penetration of the reaction and the shape of the reaction front were determined. The weight of the gel fraction gave directly an estimate of the depth of penetration, λ_x which decreased with increasing film thickness. This was attributed to the increased amount of reacted polymer being noncrosslinked material (sol) in the interior compared to the 100% crosslinked nature of the surface region and to a reduction in the penetration of the reaction front resulting from the effect of stress transfer in lowering the permeation rate of peracetic acid. Comparison of the depth of penetration estimates λ_x and λ_s determined from the weight of the unreacted polymer demonstrated that, for the conditions used, the reaction front is quite broad. (For example, at 40°C, in 71% acetic acid for 80 min, the fully crosslinked portion is 15 μm thick and the partially reacted region extends for another 8.5 μm.) The combined influences of the increase in penetration of the reactants in the polymer and the relief of stress secondary to this increase in penetration were reflected in the time dependence of the depths of penetration λ_x and λ_s.     

Regulating Gelation Time and Kinetics Analysis Based on the ARGET ATRP Mechanism

A novel activators regenerated by electron transfer (ARGET) atom transfer radical polymerization (ATRP) initiation system composing of an initiator sodium chloroacetate, a catalyst ferric chloride, and a reducing agent ascorbic acid was developed to improve the gelation time of the in situ crosslinked polymer system. The kinetics of polymerization of acrylamide showed features of a living/controlled process in which the concentrations of the growing radicals [P·] are kept constant throughout the polymerization process. Compared with conventional potassium persulfate initiators, the gelation time of the in situ crosslinked polymer system can be improved to 40 h or even longer using the ARGET ATRP initiation system at 80 °C due to the low radical concentration and slow polymerization reaction. Core flooding test showed that the ARGET ATRP initiating system developed could initiate the polymerization reaction of the in situ crosslinked polymer system in the core. However, the gelation time was extended in comparison to that of the result obtained in the bottle, resulting from the dilution and adsorption of ARGET ATRP components during the injection process. The research expands the application field of the ARGET ATRP principle and has a promising prospect on controlling the gelation time of the in situ crosslinked polymer system. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 519–527     

Thermostable poly(p-phenylene sulfide sulfonic acid) as ion exchangers

Poly(p-phenylene sulfide sulfonic acid) was thermally crosslinked for use as a cation exchange polymer with high thermal stability. The decomposition temperature (T_d) of the polymer increases with an increase in the crosslinking temperature. The crosslinking reaction at 300°C in air resulted in the formation of a strongly acidic cation exchange polymer with a T = 467°C and having an SO₂ bond, whose crosslinked structure was investigated using IR spectroscopy.     

可注射性骨组织工程支架材料不饱和聚磷酸酯的合成

以富马酸、1,2-丙二醇和三氯氧磷为起始原料,合成了主链重复结构单元中含不饱和双键的聚磷酸酯.FTIR及NMR研究表明.不饱和聚磷酸酯(UPPE)主链结构中含有富马酸二(1,2-丙二醇)酯(BPGF)的三种异构体.利用GPC研究了反应时间对聚合反应的影响,结果表明,延长反应时间有利于提高分子量,聚合物趋向于单分散性.反应18 h后,聚合物重均分子量达到5 956 g/mol,分散度为1.12.通过测定UPPE与N-乙烯基吡咯烷酮(NVP)的交联温度曲线,确定交联反应最高温度为41.14-82.30℃,固化时间在1.95-10.28 m in之间.     

Photovoltaic properties of the polymer solar cells comprising crosslinked maleimide polymers and fullerene‐derivative PCBM

A series of crosslinkable maleimide conjugated polymers with different vinyl group contents as side‐chain crosslinking sites have been synthesized by the Suzuki coupling reaction. Polymer solar cells (PSCs) were fabricated based on an interpenetrating network of the crosslinkable maleimide polymers as the electron donor, and a fullerene derivative, (6,6)‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM), as the electron acceptor. The crosslinkable maleimide polymers underwent crosslinking reaction at the side‐chain vinyl groups upon the thermal treatment with or without the addition of initiator, azobisisobutyronitrile (AIBN). Better photovoltaic (PV) performances were obtained for the PSCs based on the polymer crosslinking without using initiator, whereas poorer PV performances were observed for the PSCs based on the polymer crosslinking with the AIBN initiator. In addition, higher operational stability was observed for the crosslinked polymer based solar cell as compared to the solar cell based on the un‐crosslinked polymer. The photo‐physical and PV properties of the cross‐linked maleimide polymers/PCBM based PSCs are discussed in detail as the morphology and crosslinking density of the polymers are taken into account. Copyright © 2010 John Wiley & Sons, Ltd.     

Ionic organic/inorganic materials. II. New linear and crosslinked poly(ethylene oxide)‐based ionomers by quaternization with chloroalkyl‐functionalized siloxanes

Siloxane‐modified cationic polyelectrolytes were synthesized through the quaternization reaction of a poly(ethylene glycol)‐based polymer containing tertiary amine groups in the chain with chloroalkyl‐functionalized siloxanes. Linear or crosslinked structures were obtained, depending on the functionality of the siloxane: a chloroalkyl‐monofunctionalized or ‐polyfunctionalized siloxane was used. The reaction occurred in solution with n‐propanol as a solvent and NaI as a catalyst. All products were characterized with elemental analysis and IR and ¹H NMR spectrometry. Viscometric measurements of the linear polymer in dilute aqueous solutions revealed typical polyelectrolyte behavior. The swelling capacities in various solvents of the crosslinked structures were determined. The thermal stability of the crosslinked cationic structures obtained with a polyfunctional siloxane as a quaternization agent was much higher than that of the parent polymer. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3720–3728, 2004     

UV‐induced crosslinking of ring opening metathesis block copolymer micelles

Statistical and amphiphilic block copolymers bearing cinnamoyl groups were prepared by ring opening metathesis polymerization (ROMP). The UV‐induced [2 + 2] cycloaddition reaction of polymer bound cinnamic acid groups was studied in polymer thin films as well as in block copolymer micelles. In both cases, exposure to UV‐light for 10 min led to a crosslinking conversion of about 60%, as determined by FT‐IR spectroscopy and UV–vis absorption measurements. Time based IR‐spectroscopy revealed a maximum conversion of 78% reached after an irradiation time of about 16 min. For micelles obtained from polymers bearing 5 mol % or more cinnamoyl groups, the crosslinking reaction proceeded smoothly, yielding in crosslinked particles which were stable in a non‐selective solvent (CHCl₃). Diameters determined by dynamic light scattering in the selective solvent (MeOH) were similar for both, non‐crosslinked and crosslinked micelles, whereas diameters of crosslinked micelles in the non‐selective solvent (CHCl₃) were significantly larger compared to MeOH samples. This strategy of direct self assembly of block‐copolymers in a selective solvent followed by “clean” crosslinking, without the need for additional crosslinking reagents or crosslinking initiators, provides a straight forward approach toward ROMP‐based polymeric nano‐particles. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2402–2413, 2008     

Click chemistry in materials synthesis. II. Acid‐swellable crosslinked polymers made by copper‐catalyzed azide–alkyne cycloaddition

A highly crosslinked hyperbranched polymer that rapidly swells and shrinks in a halogenated solvent in response to the addition of an acid or base has been prepared by Cu(I) catalysis of the reaction between a diazide and an amine‐containing trialkyne. The triazole linkages in the polymer are highly stable and may also play a role in the swelling behavior. The swelling–deswelling process is reversible. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5513–5518, 2006