微波消解-零交截距导数分光光度法同时测定催化剂中钴和镍

采用微波法消解催化剂 ,研究确定了微波消解催化剂的最佳工作条件。应用零交截距导数分光光度法解决了 PAR- CO2 +、PAR- Ni2 +体系中 Co2 +、Ni2 +的同时测定。钴和镍的线性范围分别为 0～ 30 μg/ 2 5m L和 0～ 2 5μg/ 2 5m L,催化剂样品中钴和镍测定结果的相对标准偏差 (n=5)分别≤ 1 .5%和≤ 1 .0 % ,与标准值相对误差分别≤± 1 .5%和≤± 2 .1 %。本方法测定催化剂中钴和镍 ,酸用量少 ,降低了环境污染     

流动注射-微柱在线富集/电感耦合等离子发射光谱法测定中成药中痕量铅和镉

采用自制固相萃取材料PTFE-g-GMA-PEI纤维填充微柱预富集和流动注射(FI) 与电感耦合等离子发射光谱仪联用, 测定样品中痕量Pb2+和Cd2+.对Pb2+和Cd2+的富集与洗脱条件进行优化,并给出相应离子的分析特性.结果表明: 本方法Pb2+和Cd2+检出限分别为3.5和0.15 μg/L; 富集倍数分别为30和80; RSD分别为1.5%和0.6%(n=9,单个离子浓度为50 μg/L).本方法应用于几种中成药中的痕量铅和镉的同时测定,样品加标回收率在90%～108% 之间, 结果满意.     

硫酸铵-溴化钾铵-正丙醇体系萃取分离和富集锗的研究

研究了硫酸铵-溴化钾铵-正丙醇体系萃取分离和富集锗的行为及与一些金属离子分离的条件.硫酸铵能使正丙醇的水溶液分成两相,在分相过程中,Ge4+与KBr生成(GeBr62-),并与质子化正丙醇(C3H7OH2+)形成缔合物[GeBr62-][C3H7OH2+]2,此缔合物能被正丙醇相完全萃取.当正丙醇、KBr和硫酸铵的浓度分别为30％(V/V)、7.0×10-3mol/L、0.20g/mL时,(GeBr62-)的萃取率达到97.7％以上,而Ni2,Pb2,Cr3+,Co2,Fe3+,Al3+,Mg2+,Ag+,Bi3+,CH2,W(Ⅵ)和V(Ⅴ)基本不被萃取,实现了Ge4+与上述金属离子的分离.     

阳离子选择性耗尽进样-胶束扫集法测定尿液中的麻黄碱和可待因

联用选择性耗尽进样和胶束扫集两种在线富集技术,建立了尿样中麻黄碱和可待因含量测定的灵敏方法,并通过日内、日间、柱间实验考察了方法的稳定性.胶束扫集电动色谱缓冲体系为80 mmol/L 十二烷基磺酸钠(SDS)-20 mmol/L NaH2PO4(pH 2.20)-18%乙腈(V/V),分离电压-20 kV,进样电压10 kV,进样时间150 s,测量波长200 nm.同时讨论了pH值、SDS浓度、选择性耗尽进样萃取液电导、进样电压、进样时间和进水长度等对分离效果的影响.结果显示,方法富集功能很强,对麻黄碱和可待因含的富集倍数分别达5800和2490以上.在优化条件下,方法线性关系良好(r=0.9999),麻黄碱和可待因的线性范围分别为0.500～16.0 μg/L和2.00～48.0 μg/L,检出限分别为0.10和0.80 μg/L.方法稳定性良好,日内、日间和柱间的RSD分别为2.6%,5.9%和6.6%.应用于实际尿样分析,回收率在96.8%～106%之间,RSD≤4.7%,结果比较满意.     

锑电极电位溶出法测定锌、镉、铅

提出了采用锑电极作为工作电极同时测定痕量重金属锌、镉、铅的电位溶出法。探讨了同时测定锌、镉、铅的最佳条件。在pH=5.0的HAc-NaAc缓冲溶液中,Zn2+、Cd2+、Pb2+分别在-1.07、-0.70、-0.52 V得到灵敏的电位溶出峰。沉积时间为60 s时,锌、镉、铅的质量浓度分别在0~16.0、0~1.6、0~0.08 μg/mL范围内,与各自微分电位溶出峰高呈线性关系,检出限分别为4.0、0.3、0.03 μg/L。测定了水样中痕量锌、镉、铅的含量,结果令人满意。     

络合吸附溶出伏安法测定茶叶中的痕量锌

通过实验优化支持电解质、pH值、络合剂浓度等实验参数。在溶液中直接以SCN-作配位剂 ,采用玻碳电极同位镀汞的吸附伏安法测定锌。在该体系中 ,Zn2 + 和SCN-配合物可产生灵敏吸附波 ,峰电位为 - 1.372V ,线性范围为 1.96 2～ 130 .8μg/L ,搅拌富集 5min ,检出限可达 8× 10 -10 mol/L。该法用于测定茶叶中的锌 ,平均回收率为 95 .0 %～ 10 2 .5 %。     

HPLC-AFS联用测定海产品中砷的形态

建立了高效液相色谱-原子荧光分光光度法测定海产品中无机砷(As V,AsⅢ)、有机砷(DMA,MMA,AsB)含量的方法.样品经含10％(体积分数)HC1的提取液振荡提取、离心分离、二路形态分析预处理、高效液相色谱分离,用原子荧光光度计检测As(Ⅲ),DMA,MMA,As(v);四路条件(过氧化氢氧化和开启紫外灯)形态分析预处理装置处理,高效液相色谱分离,原子荧光光度计测定AsB.As(Ⅲ)线性范围为0～100.00 μg/L,r2=0.9997;DMA线性范围为0～100.00 μg/L,r2=0.9993;MMA线性范围为0～100.00 μg/L,r2=0.9990;As(Ⅴ)线性范围为0～100.00 μg/L,r2=0.999 1;AsB线性范围为0～200.00 μg/L,,r2=0.9994.3个样品加标回收率为As(Ⅲ)86.7％～89.4％,DMA 111.2％～117.0％,MMA 109.7％～111.6％,As(Ⅴ) 83.8％～90.7％,AsB 88.3％～90.4％.用该方法测定虾仁(干)5个价态测定结果的相对标准偏差为3.07％～9.93％(n=6).5个价态的检出限(S/N=2)为As(Ⅲ)0.29 μg/L,DMA 0.36 μg/L,MMA 0.27 μg/L,As(V) 0.56 μg/L,AsB l.46 μg/L.该方法适用于海产品中As(Ⅲ),DMA,MMA,As(V),AsB含量的测定.     

毛细管电泳-电容耦合非接触电导法检测牛奶中金属离子和三聚氰胺

采用毛细管电泳-电容耦合非接触电导法检测牛奶中金属离子和三聚氰胺的含量.以20 mmol/L乳酸溶液为背景电解质,采用毛细管(50 μm×50 cm,有效长度40 cm),电导检测器的操作参数为180 kHz×8 V,对标准品和牛奶中K+, Ca2+和Na+的检出限为0.009～0.040 μg/g,对三聚氰胺的检出限为0.10～0.20 μg/g.本方法仪器简单,可以对牛奶中三聚氰胺及无光学活性的无机离子进行快速准确的检测.     

差分脉冲溶出伏安法测定陶瓷器皿中铅和镉的溶出率

采用4%的乙酸浸泡陶瓷样品24 h,应用同位镀汞差分脉冲溶出伏安法测定了陶瓷样品中微量重金属铅、镉的溶出量。以0.1 mol/L的硝酸溶液做底液,0.1 mol/L的KCl溶液做支持电解质,2 g/L的Hg2+溶液做镀汞液,测得铅的溶出峰电位为-0.5 V(vsSCE),镉的溶出峰电位为-0.7 V(vsSCE),两者含量在5×10-4～1 mg/L和5×10-4～0.5 mg/L范围内峰电流和其含量呈良好的线性关系,检出限分别为2×10-4和4.3×10-3mg/L。     

米面中痕量铍的微波消解-固相萃取/石墨炉原子吸收光谱法分析

建立了微波消解-固相萃取/石墨炉原子吸收法富集并测定米面中痕量铍的方法.采用微波消解制样,7-(2'-胂酸基-5'-羧酸)苯偶氮-8-羟基喹啉-5-磺酸(H2L)与Be2+螯合形成BeL络合物,C18固相萃取柱(C18-SPE)富集BeL,石墨炉原子吸收法测定C18柱洗脱液中的BeL.最佳实验条件为:采用50 μL pH 3.0的50 g/L H2L水溶液与样品中的铍螯合15 min,水相上柱,用2 mL 50%(体积分数)甲醇溶液洗脱.结果表明,方法的线性范围为0.05 ～14 μg/L,检出限为0.02 μg/L,对实际米面样品测定的加标回收率为90% ～110%,可用于食品等复杂基质中痕量铍的测定.     

Electrothermal Atomic Absorption Spectrometric Determination of Cobalt,Copper and Nickel in Fresh Water After Their Preconcentration by Precipitate Flotation

Abstract

A method is developed for simultaneous separation and determination of μg/L levels of Co(II), Cu(II) and Ni(II) in fresh water by precipitate flotation. The optimal conditions of the experimental procedure with hydrated iron(III) oxide and iron(III) tetramethylenedithiocarbamate as collectors were investigated. The pH interval of the working medium, within which Co(II), Cu(II) and Ni(II) can be successfully separated, was determined from the aspect of collectors and surfactant stability. The amounts of the elements investigated were determined by electrothermal atomic absorption spectrometry. The detection limit of the method is 0.15 μg/L for cobalt, 0.03 μg/L for copper and 0.79 μg/L for nickel.     

Determination of Trace Vanadium by Adsorptive Stripping Voltammetry at a Carbon Paste Electrode

A method for the voltammetric determination of vanadium using a carbon paste electrode (CPE) was described. The new procedure is based on the adsorptive accumulation of the V(V)‐alizarin red S(ARS) complex onto the surface of the CPE, followed by the electrochemical reduction of adsorbed species. The optimal experimental conditions include the use of 0.10 mol/L acetate buffer (pH 5.1), 1.0×10^?5 mol/L ARS, an accumulation potential of ?0.10 V (versus SCE), an accumulation time of 2 min, a scan rate of 200 mV/s and a second‐order derivative linear scan mode. The reduction peak for the complex appears at ?0.52 V. The peak current is proportional to the concentration of V(V) over the range of 0.10–15.0 μg/L, and the detection limit is 0.04 μg/L for a 2 min adsorption time. The relative standard deviations(n=8) for 2.0 and 0.50 μg/L V(V) are 3.1 and 4.7%, respectively. The proposed method was applied to the determination of vanadium in water samples.     

Chromotropic acid-functionalized polyurethane foam: A new sorbent for on-line preconcentration and determination of cobalt and nickel in lettuce samples

A chromotropic acid-functionalized polyurethane foam has been developed for use in an on-line preconcentration system for cobalt and nickel determination. The packing material was prepared by covalent coupling of chromotropic acid with the polyurethane foam through an azo group. Co and Ni ions were sorbed in the mini-column, from which they could be eluted directly to the nebulizer-burner system of a flame atomic absorption spectrometer. Elution of cobalt and nickel from the mini-column can be accomplished with 0.50 and 0.75 M HCl solutions, respectively. The enrichment factors obtained were 22 (Co) and 27 (Ni), for 60 s preconcentration time, and 57 (Co) and 59 (Ni), if a preconcentration time of 180 s was used. Under the optimum conditions, the proposed procedure allowed the determination of metals with detection limits of 0.43 (cobalt) and 0.52 microg/L (nickel), respectively, on using preconcentration periods of 180 s. The accuracy of the developed procedure was evaluated by analysis of the certified reference materials NIST 1515 Apple Leaves and NIST 1570a Spinach Leaves. The method was applied to the analysis of lettuce samples. The contents of cobalt in the samples analyzed varied from 0.75 to 0.98 microg/g. Nickel was not detected in the lettuce samples.     

MWCNTs/Ionic Liquid/Graphene Quantum Dots Nanocomposite Coated with Nickel‐Cobalt Bimetallic Catalyst as a Highly Selective Non‐enzymatic Sensor for Determination of Glucose

In this work, a glassy carbon electrode (GCE) was modified with multiwall carbon nanotubes/ionic liquid/graphene quantum dots (MWCNTs/IL/GQDs) nanocomposite. Then, the nanocomposite was decorated with nickel‐cobalt nanoparticles (Ni?Co NPs), and it was used as a non‐enzymatic glucose sensor. Field emission scanning electron microscopy, X‐ray diffraction spectroscopy, and energy dispersive spectroscopy were employed to prove the electrodeposition of the Ni?Co NPs on the surface of MWCNTs/IL/GQDs/GCE. Also, cyclic voltammetric and amperometric methods were utilized for the investigation of the electrochemical behaviour of the Ni?Co NPs/MWCNTs/IL/GQDs/GCE for glucose oxidation. The novel amperometric sensor displayed two linear ranges from 1.0 to 190.0 μmol L^?1 and 190.0 to 4910 μmol L^?1 with a low detection limit of 0.3 μmol L^?1 as well as fast response time (2 s) and high stability. Also, the sensor showed good selectivity for glucose determination in the presence of ascorbic acid, citric acid, dopamine, uric acid, fructose, and sucrose, as potential interference species. Finally, the performance of the proposed sensor was investigated for the glucose determination in real samples. Ni?Co NPs/MWCNTs/IL/GQDs/GCE showed good sensitivity and excellent selectivity.     

Simultaneous Trace Determination of Nickel and Cobalt in Natural Waters by Differential Pulse Polarography

Abstract

A differential pulse polarographic method has been developed for the simultaneous low level determination of nickel and cobalt in the presence of furildioxime in natural waters. The nature of the electrode processes was studied with cyclic voltammetry. Limits of determination of 0.4 μg/L and 0.15 μg/L were achieved for nickel and cobalt respectively     

Study on the Determination of Cobalt,Nickel, Copper,Zinc and Vanadium in Environmental Samples by a Rapid High‐Performance Liquid Chromatography

A new method for the simultaneous determination of five transition metal ions in water and food by rapid high‐performance liquid chromatography was developed. The cobalt, nickel, copper, zinc and vanadium ions were pre‐column derivatized with 2‐(2‐quinolinylazo)‐4‐methyl‐1,3‐dihydroxidebenzene (QAMDHB) to form colored chelates, then the Co‐QAMDHB, Ni‐QAMDHB, Cu‐QAMDHB, Zn‐QAMDHB and V‐QAMDHB chelates were enriched by solid phase extraction with a C18 cartridge. The enrichment factor of 50 was achieved by eluting the retained chelates from the cartridge with tetrahydrofuran (THF). These chelates were separated on a ZORBAX Stable Bound rapid analysis column (4.6 × 50 mm, 1.8 um) with 68% methanol (containing 0.1% of acetic acid and 0.1% of CTMAB) as mobile phase at a flow rate of 2.0 mL/min and detected with a photodiode array detector from 450?600 nm. The Co‐QAMDHB, Ni‐QAMDHB, Cu‐QAMDHB, Zn‐QAMDHB and V‐QAMDHB chelates were separated completely within 2.0 min. The detection limits of cobalt, nickel, copper, zinc and vanadium are 2 ng/L, 1.5 ng/L, 2 ng/L, 3 ng/L, and 3 ng/L, respectively, in the original samples. This method was applied to the determination of the five transition metal ions in water and food samples with good results.     

Bismuth film electrode for simultaneous adsorptive stripping analysis of trace cobalt and nickel using constant current chronopotentiometric and voltammetric protocol

Bismuth film electrode (BiFE) is presented as a promising alternative to mercury electrodes for the simultaneous determination of trace cobalt and nickel in non-deoxygenated solutions. The preplated BiFE was employed under adsorptive stripping constant current chronopotentiometric and adsorptive stripping voltammetric conditions in the presence of dimethylglyoxime complexing agent. BiFE exhibited well-defined and undistorted signals with favorable overall resolution for cobalt and nickel cations, with the signals for both metal cations being practically independent of each other. The stripping performance of BiFE is characterized by good reproducibility (RSD 1.4% for Co(II), and 4.3% for Ni(II)), low detection limits of 0.08 μg l⁻¹ for Co(II) and 0.26 μg l⁻¹ for Ni(II) employing a deposition time of 60 s, in addition to good linearity. The non-toxic character of bismuth imparts the possibility of tailoring disposable and one-shot electrochemical sensors for decentralized environmental, clinical and industrial monitoring of trace cobalt and nickel.     

Determination of Ni and Co using 2-quinolinethiol by adsorptive voltammetry

Summary A new method for the simultaneous determination of cobalt and nickel has been developed by differential pulse adsorptive voltammetry using 2-quinolinethiol as chelate. A separation of the two peaks by 0.3 V was achieved, allowing the determination of the two metals in a wide range of concentrations. The influence of pH, nature of the supporting electrolytes, preconcentration time and applied potential was investigated. Pb, Cd, Fe, Zn and Cr do not interfere. The determination limits were 10^–8 mol/l for Co and 10^–9 mol/l for Ni. The method was applied to mussel tissues and wines.     

Porous microtubes of nickel-cobalt double oxides as non-enzymatic hydrogen peroxide sensors

Non-enzymatic electrochemical sensors for the determination of hydrogen peroxide(H_2 O_2) have attracted more and more concerns.A series of nickel and cobalt double oxides(Ni_xCo_y-DO) with the different ratios of Ni/Co have been prepared by a polyol-mediated solvothermal method for H_2 O_2 detection.The obtained products exhibit honeycomb-like open porous microtubes constituted with the low-dimensional nanostructured Ni_xCo_y-DO blocks after the calcination treatment.Compared with nickel oxides,the introduced Co ions in Ni_xCo_y-DO can induce the production of surficial oxygen vacancies,and further enhance the electrode surface activity.In particular,the NiCo-DO sample(with an atomic ratio of Ni/Co=4:3) shows the richest surficial oxygen vacancies and presents the highest H_2 O_2 detection activity among all the as-prepared samples,demonstrating an excellent sensitivity of698.60 μAL mmol ~1 cm~(-2)(0～0.4 mmol/L),low detection limit(0.28 μmol/L,S/N=3),as well as long stability,high selectivity and good reproducibility.This work lends a new impetus to the potential application of double metal oxides for the next generation of non-enzymatic sensors.     

Analysis of binary and ternary mixtures of cobalt,nickel and copper by differential kinetic methods based on ligand substitution reactions

The methods are based on displacement of pyridoxal thiosemicarbazone from its complexes with cobalt, nickel and copper(II) with DCTA. The reactions are monitored spectrophotometrically at 425 nm. The Ni/Cu and Co/Ni/Cu mixtures are analyzed by the single-point method and the Co/Ni and Co/Cu mixtures by the logarithmic extrapolation method. In all determinations the relative standard deviation is <3%, at the μg ml^?1 level.