Comparison of volatile constituents extracted from model grape juice and model wine by stir bar sorptive extraction-gas chromatography-mass spectrometry

A stir bar sorptive extraction (SBSE) method coupled with gas chromatography-mass spectrometry was optimised for the analysis of volatile components of a model wine, based on a previously optimised method used for analysis of the same components in model grape juice. The presence of ethanol in the model wine sample matrix resulted in decreased sensitivity of the method toward most of the volatile constituents. Mean percent relative recoveries and reproducibilities (%CV) were 22.8% and 7.1%, respectively, compared with 28.4% and 8.5% for model grape juice. The mean limit of detection (LoD) ratio (juice:wine) was 0.25. Similar sensitivities for the two sample matrices using this method were achieved by changing the split ratio from 20:1 (grape juice) to 5:1 (wine), giving a mean limit of detection ratio (juice:wine) of 1.0, thus allowing direct comparison of chromatograms of volatile components in the two matrices. This enabled direct comparisons of grape juices and the wines derived from them by alcoholic yeast fermentation. The influence of ethanol concentration in the range 9-15% on method sensitivity is discussed, using an overlay of the total ion chromatograms. The use of a gas saver device for the 5:1 split ratio analysis of desorbed model wine aroma compounds is discussed in terms of preventing extraneous reaction of sorbent and stationary phases with air during analysis.     

Optimized determination of calcium in grape juice,wines, and other alcoholic beverages by atomic absorption spectrometry

This paper describes a study of the different methods of sample preparation for the determination of calcium in grape juice, wines, and other alcoholic beverages by flame atomic absorption spectrometry; results are also reported for the practical application of these methods to the analysis of commercial samples produced in Spain. The methods tested included dealcoholization, dry mineralization, and wet mineralization with heating by using different acids and/or mixtures of acids. The sensitivity, detection limit, accuracy, precision, and selectiviy of each method were established. Such research is necessary because of the better analytical indexes obtained after acid digestion of the sample, as recommended by the European Union, which advocates the direct method. In addition, although high-temperature mineralization with an HNO3-HCIO4 mixture gave the best analytical results, mineralization with nitric acid at 80 degrees C for 15 min gave the most satisfactory results in all cases, including those for wines with high levels of sugar and beverages with high alcoholic content. The results for table wines subjected to the latter treatment had an accuracy of 98.70-99.90%, a relative standard deviation of 2.46%, a detection limit of 19.0 microg/L, and a determination limit of 31.7 microg/L. The method was found to be sufficiently sensitive and selective. It was applied to the determination of Ca in grape juice, different types of wines, and beverages with high alcoholic content, all of which are produced and widely consumed in Spain. The values obtained for Ca were 90.00 +/- 20.40 mg/L in the grape juices, 82.30 +/- 23.80 mg/L in the white wines, 85.00 +/- 30.25 mg/L in the sweet wines, 84.92 +/- 23.11 mg/L in the red wines, 85.75 +/- 27.65 mg/L in the rosé wines, 9.51 +/- 6.65 mg/L in the brandies, 11.53 +/- 6.55 mg/L in the gin, 7.3 +/- 6.32 mg/L in the pacharán, and 8.41 +/- 4.85 mg/L in the anisettes. The method is therefore useful for routine analysis in the quality control of these beverages.     

Determination of histamine in port wines and grape juices by ion-pair extraction and stable isotope dilution GC-MS

Summary An isotope dilution, GC-MS method for the quantitation of histamine in wines and grape juices was assayed. This method includes isolation of histamine and its, deuterated analogue [α,α,β,β-²H₄]histamine, used as the labelled internal standard, by ion-pair extraction with bis-2-ethylhexylphosphate, conversion to the volatile derivative: tris-pentafluorobenzyl-histamine, capillary GC separation and measurement of the abundance ratio of the (M-181)⁺ ions from labelled and unlabelled derivatives. The method was successfully applied to the determination of histamine in several samples of Port wine, red and white table wine and grape juice. Data are given on detectability, linearity, repeatability and recovery.     

Direct determination of Cd, Cu and Pb in wines and grape juices by thermospray flame furnace atomic absorption spectrometry

The applicability of thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS) was evaluated for direct determination of Cu, Cd and Pb in wines and grape juices. The developed procedure does not require preliminary acid digestion of the samples. The optimum conditions for determination of Cu, Cd and Pb in wines were studied and the performance was compared to those typically obtained by flame atomic absorption spectrometry (FAAS). A sample volume of 150 microL was introduced into a heated nickel tube at a flow rate of 0.54 mLmin(-1) and 0.14 molL(-1) HNO(3) was used as sample carrier flowing at 2.5 mLmin(-1) for determining all analytes. The effect of ethanol concentrations on Cu, Cd and Pb absorbance signals were studied. All determinations were carried out by adopting optimized conditions and quantification was based on the standard additions method. Limits of detection (LOD) of 12.9, 1.8 and 5.3 microgL(-1) (n=14) for Cu, Cd and Pb, respectively, were obtained for wine samples (3sigma(blank)/slope, n=14). Relative standard deviations (R.S.D., %) of 2.7, 2.1 and 2.6 for Cu, Cd and Pb, were obtained (n=6) for wine samples. The values determined for grape juice samples were similar to these ones. The analytical throughput was 45 determinations h(-1) and accuracy was checked by addition-recovery experiments.     

Ochratoxin A survey in Portuguese wine by LC-FD with direct injection

Wine and grape juices were identified as one of the most important sources of ochratoxin A (OTA), a mycotoxin with diverse toxic effects that naturally appears in food and foodstuffs all over the world.The aim of this study was to assess the OTA levels in Portuguese wines through the application of a simple and accurate method based on liquid chromatography (LC) with direct injection, followed by fluorescence detection (FD).Randomly selected wine samples were used to evaluate the performance of direct injection as efficient, fast, inexpensive and safe sample preparation method. The proposed method was successfully validated. The limit of quantification (LOQ) was 1.0 μg/L and OTA recoveries from wine samples, spiked at the three fortification levels, were higher than 85.4%, with RSDs lower than 9.6% for both red and white wines. The presence of OTA was confirmed by methyl ester derivatization followed by LC analysis.Data on OTA levels were obtained for 60 Portuguese red and white wine samples. OTA was found in 12 samples, nine (26%) red wine samples and three (12%) white wine samples. Only one red wine sample and one white wine sample presented a contamination level above the LOQ, with 1.23 and 2.4 μg/L, respectively. It should be pointed out that this white wine sample exceeded the EC maximum permitted level of 2.0 μg/L. The safe dose established as 120 ng/kg body weight/week was not exceeded by the weekly intake estimated for the samples contaminated above the LOQ.     

Optimized determination of iron in grape juice, wines, and other alcoholic beverages by atomic absorption spectrometry

This paper describes a study of the different methods of sample preparation for the determination of iron in grape juice, wines, and other alcoholic beverages by atomic absorption spectrometry with electrothermal atomization; results are also reported for the practical application of these methods to the analysis of commercial samples produced in Spain. The methods examined include dealcoholization and dry and wet mineralization treatment using different acids and/or mixtures of them, both with and without heating. The sensitivity, detection limit, accuracy, precision, and selectivity of each method were established. The best results were obtained for wet mineralization with heated acid (HNO3-H2SO4); the results for table wines had an accuracy of 97.5-101.6%, a relative standard deviation of 3.51%, a detection limit of 19.2 micrograms/L, and a determination limit of 32.0 micrograms/L. The method was also sufficiently sensitive and selective. It was applied to the determination of iron in grape juice, different types of wines, and beverages with high alcoholic content, all of which are produced and widely consumed in Spain. The values obtained ranged from 3.394 +/- 2.15 mg/L for the juice, 2.938 +/- 1.47 mg/L for the white wines, 19.470 +/- 5.43 mg/L for the sweet wines, 0.311 +/- 0.07 mg/L for the brandies, and 0.564 +/- 0.12 mg/L for the anisettes. Thus, the method is useful for routine analysis in the quality control of these beverages.     

Development of a routine analysis of 4-mercapto-4-methylpentan-2-one in wine by stable isotope dilution assay and mass tandem spectrometry

The 4-mercapto-4-methylpentan-2-one (4MMP) is a key aroma compound in wines, especially in Sauvignon Blanc ones. Its accurate quantification is quite difficult due to its traces levels and its reactivity in wine conferred by the thiol function. In this paper, we proposed a new method for its quantification in wine without any sample preparation, based on automated derivatization procedure by methoximation and SIDA–SPME–GC–MS/MS analysis. The derivatization procedure was adapted from a previously published method in order to decrease the amount of reagents and the volume of wine (only 3 mL are required). The use of SPME and the detection conditions have also been optimized to reach the best sensitivity as possible. The method was then validated according to the International Organization of Vine and Wine recommendations and exhibited excellent performances. Indeed, this method allowed us to quantify the 4MMP in wine at traces levels (LOD = 0.19 ng L⁻¹) with reproducible results (RSD < 15%) and a very good accuracy (recovery = 102%).     

Varietal discrimination of Australian wines by means of mid-infrared spectroscopy and multivariate analysis

This study outlines the use of mid-infrared (MIR) spectroscopy combined with principal component analysis (PCA) and linear discriminant analysis (LDA) for the varietal classification of commercial red and white table wines. Three red varieties (Cabernet Sauvignon, Shiraz and Merlot) and four white varieties (Chardonnay, Riesling, Sauvignon Blanc and Viognier) were sourced from different wine regions in Australia. Wine samples were scanned in transmission on a FOSS WineScan FT 120 from wave numbers 926 to 5012 cm⁻¹. All samples were sourced from the 2006 vintage and had not been blended with any other variety or wine from other regions. Spectral data were reduced to a small number of principal components (PCs) and LDA was then performed to successfully separate the wines into the different varieties. To test the robustness of the LDA models developed for the red wines, a set of red wines scanned in 2005 were used. Correct classification of over 95% was achieved for the validation set.     

Headspace solid-phase microextraction–gas chromatography–mass spectrometry for profiling free volatile compounds in Cabernet Sauvignon grapes and wines

The complex aroma of wine is derived from many sources, with grape-derived components being responsible for the varietal character. The ability to monitor grape aroma compounds would allow for better understanding of how vineyard practices and winemaking processes influence the final volatile composition of the wine. Here, we describe a procedure using GC–MS combined with headspace solid-phase microextraction (HS-SPME) for profiling the free volatile compounds in Cabernet Sauvignon grapes. Different sample preparation (SPME fiber type, extraction time, extraction temperature and dilution solvent) and GC–MS conditions were evaluated to optimize the method. For the final method, grape skins were homogenized with water and 8 ml of sample were placed in a 20 ml headspace vial with addition of NaCl; a polydimethylsiloxane SPME fiber was used for extraction at 40 °C for 30 min with continuous stirring. Using this method, 27 flavor compounds were monitored and used to profile the free volatile components in Cabernet Sauvignon grapes at different maturity levels. Ten compounds from the grapes, including 2-phenylethanol and β-damascenone, were also identified in the corresponding wines. Using this procedure it is possible to follow selected volatiles through the winemaking process.     

高效液相色谱法测定红葡萄酒中白藜芦醇的四种异构体

将红葡萄酒用β-葡萄糖苷酶水解处理,使其中的白藜芦醇甙转换成白藜芦醇。采用高效液相色谱法测定水解前后顺、反式白藜芦醇含量的变化,从而计算出葡萄酒中白藜芦醇的4种异构体的含量。色谱柱为Symmetry C18柱(3.9 mm i.d.×150 mm),流动相为乙醇-0.05%乙酸水溶液(体积比为23∶77),紫外检测波长为306 nm。实验结果表明:白藜芦醇的4种异构体在其质量浓度为0.2~50.0 mg/L时均有良好的线性关系(r>0.999),白藜芦醇及其甙的顺、反异构体的最小检出量分别为:0.81     

Validation of two analytical methods for the determination of ochratoxin A by reversed-phased high-performance liquid chromatography coupled to fluorescence detection in musts and sweet wines from Andalusia

Some Spanish sweet wines are made from raisins, grapes dried by direct exposure to the sun after picking. This drying process can encourage ochratoxin A (OTA) formation. OTA is a mycotoxin formed by several fungi. It has been linked to nephropathy in humans, and may have a long half-life in humans. The aim of this study is to develop and to apply two procedures for the analysis of OTA in grape musts (during the raisining process) and sweet wines, respectively. Reversed-phase high-performance liquid chromatography (RP-HPLC) coupled to fluorescence detection (FLD) was employed in both analytical methods. In grape must, the method involves the direct injection of the sample in a HPLC-FLD system without any kind of prior clean-up procedure. The complexity of the sweet wine samples requires a solid-phase extraction (SPE) clean-up on a C18 column which enables the OTA to be isolated from the matrix. The methods used were statistically validated. The validation also included the comparison of the slopes of the curve obtained with standards and the regression curves obtained by the addition of a standard. Two different studies of standard additions were conducted. One method was validated without sample preparation and it was applied to must samples. The other method was validated with SPE extraction and it was applied to sweet wine samples. Recovery was always better than 89.69%. The limit of detection (S/N = 3) and limit of quantification (S/N = 10) were established at 0.22 and 0.77 μg l⁻¹, respectively. In general, the analytical data obtained provided good results at the sub-μg l⁻¹ concentration level.     

Quantification of chitinase and thaumatin-like proteins in grape juices and wines

Chitinases and thaumatin-like proteins are important grape proteins as they have a great influence on wine quality. The quantification of these proteins in grape juices and wines, along with their purification, is therefore crucial to study their intrinsic characteristics and the exact role they play in wines. The main isoforms of these two proteins from Chardonnay grape juice were thus purified by liquid chromatography. Two fast protein liquid chromatography (FLPC) steps allowed the fractionation and purification of the juice proteins, using cation exchange and hydrophobic interaction media. A further high-performance liquid chromatography (HPLC) step was used to achieve higher purity levels. Fraction assessment was achieved by mass spectrometry. Fraction purity was determined by HPLC to detect the presence of protein contaminants, and by nuclear magnetic resonance (NMR) spectroscopy to detect the presence of organic contaminants. Once pure fractions of lyophilized chitinase and thaumatin-like protein were obtained, ultra-HPLC (UHPLC) and enzyme-linked immunosorbent assay (ELISA) calibration curves were constructed. The quantification of these proteins in different grape juice and wine samples was thus achieved for the first time with both techniques through comparison with the purified protein calibration curve. UHPLC and ELISA showed very consistent results (less than 16% deviation for both proteins) and either could be considered to provide an accurate and reliable quantification of proteins in the oenology field.     

Determination of the biogenic amines in musts and wines before and after malolactic fermentation using 6-aminoquinolyl-N-hydroxysuccinimidyl carbamate as the derivatizing agent

An accurate, rapid and sensitive high-performance liquid chromatographic (HPLC) method is reported for the determination of four biogenic amines in red and white wine samples. The method involves derivatization with 6-aminoquinolyl-N-hydroxysuccinimidyl carbamate (AQC) followed by liquid chromatography gradient elution analysis without any other sample pretreatment. The procedure developed permitted the determination of the four amines in 40 min. The relative standard deviation (RSD) values ranged from 3.1% to 6.1% in peak areas and the response was linear (R2>0.994) in a range from 0.1 to 4 mg/l. Leaving aside putrescine in Tempranillo wines, the malolactic fermentation did not exert any effect on the concentration of these compounds. On the contrary, the influence of the grape variety was important, and Tempranillo wines showed higher levels of tyramine and histamine and lesser of putrescine and cadaverine (p<0.05) than wines made with Cabernet Sauvignon.     

Quantitative determination of free and hydrolytically liberated beta-damascenone in red grapes and wines using a stable isotope dilution assay.

Quantitative analysis of free and hydrolytically liberated beta-damascenone in grapes and wines was developed, using a stable isotope dilution assay. Free beta-damascenone was isolated from grapes and wines by diethyl ether-hexane (1:1, v/v) extraction and the precursor(s) (glycosidic, polyols) of beta-damascenone using Sep-Pak Plus C18 RP cartridges. Hydrolytically liberated beta-damascenone was generated by acid hydrolysis from the precursor(s) extract. Red wines from Bordeaux (Merlot, Cabernet Sauvignon and Cabernet Franc, 1995 and 1996 vintage), Burgundy (Pinot Noir, 1995 and 1996 vintage) regions and Grenache wines from Chateauneuf du Pape and C?tes du Rh?ne (1995 vintage) were analysed to quantify free beta-damascenone. The wines made from Grenache and Cabernet Sauvignon (1996 vintage) grapes presented the highest mean amounts of free beta-damascenone, 5.4 and 5.5 micrograms l-1, respectively. Merlot, Cabernet Sauvignon and Cabernet Franc grapes of Bordeaux (1996 vintage) and their corresponding wines were analysed for quantification of free and hydrolytically liberated beta-damascenone. The levels of hydrolytically liberated beta-damascenone in grapes could predict closely the levels of free beta-damascenone in the corresponding wines after one year of ageing, i.e., almost half the levels found for the grape samples. The influence of enzyme and heat treatment of Merlot wine samples on their beta-damascenone levels was studied. Heat treatment doubled the levels of this compound, but enzyme treatment generated, in the corresponding wines, half the levels of beta-damascenone found in the non-enzyme treated wines.     

Contactless conductivity detection of sodium monofluoroacetate in fruit juices on a CE microchip

Rapid and quantitative determination of sodium monofluoroacetate in diluted fruit juices (dilution 1:9 v/v in deionized water) and tap water was performed by microchip CE, using contactless conductivity detection. A separation buffer consisting of 20 mM citric acid and histidine at pH 3.5 enabled the detection of the monofluoroacetate (MFA) anion in diluted apple juice, cranberry juice, and orange juice without lengthy sample pretreatments. The analyte was very well separated from interfering anionic species present in juices and tap water. LODs in diluted juices and tap water were determined to be 125, 167, 138, and 173 microg/L for tap water, apple juice, cranberry juice, and orange juice, respectively, based upon an S/N of 3:1. Taking into account the dilution factor, the LODs for juice samples range from 1 to 2 mg/L, which is adequate for monitoring the toxicity of MFA in these juice beverages and tap water. The calibration curves for MFA in diluted fruit juices were linear over the range of 500 microg/L to 80 mg/L. The total analysis time for detecting the MFA anion in fruit juices was less than 5 min, which represents a considerable reduction in analysis time compared to other analytical methods currently used in food analysis.     

A sensor based on electrodes supported on ion-exchange membranes for the flow-injection monitoring of sulphur dioxide in wines and grape juices

A sensitive and fast responding electrochemical sensor is described for the determination of free and total sulphur dioxide in wines and grape juices which prevents interferences coming from ethanol and other natural components. It consists of a cell provided with a porous gold working electrode supported on one face of an ion-exchange membrane, acting as a solid polymer electrolyte (SPE), which allows gaseous electroactive analytes to be detected. This sensor was used as an amperometric detector for a flow injection system in which controlled volumes of headspace equilibrated with samples were injected. This approach was adopted to make also possible the determination of total SO₂, avoiding drawbacks caused by the high relative humidity generated by the sample heating resulting from the neutralization reaction of excess NaOH, whose addition was required to release sulphur dioxide from its combined forms. Factors affecting the detection process were examined and optimised. Under the identified optimal conditions, SO₂ detection resulted in sharp peaks which allowed to infer detection limits for a signal-to-noise ratio of 3, referred to liquid samples, of 0.04 and 0.02 mg L⁻¹ for free and total SO₂ which were determined at 20 and 35 °C, respectively. Moreover, the responses were found to be characterized by good repeatability (±2% and ±4%, respectively) and linear dependence on the SO₂ concentration over a wide range (0.2-500 mg L⁻¹ for both free and total SO₂). Finally, the long-term stability of the sensor turned out to be totally satisfactory in that responses changed of ±9% alone even after long periods of continuous use. The application to some commercial wines and grape juices is also presented.     

Combined ion-pair extraction and gas chromatography-mass spectrometry for the simultaneous determination of diamines, polyamines and aromatic amines in Port wine and grape juice

An accurate and very sensitive method which allows for the simultaneous determination of the diamines (1,3-diaminopropane, putrescine and cadaverine), of the polyamines (spermidine and spermine), and of the aromatic amines (beta-phenylethylamine and tyramine) found in Port wines and corresponding grape juices is presented. Sample clean-up consisted of the extraction of the amines with the ion-pairing reagent bis-2-ethylhexylphosphate dissolved in chloroform followed by a back-extraction with 0.1 M HCl. The hydrochloric extract obtained was dried and the amines were further derivatized with heptafluorobutyric anhydride and analyzed by GC-MS in the selected ion-monitoring mode, with a total run time of 18 min. Under the adopted conditions, the extraction of all the studied compounds was almost complete and the obtained extracts were free of potential interferents present in the samples, namely sugars, and most of the amino acids and polyphenols. Via the use of a set of five selected internal standards (amphetamine, [2H8]putrescine, 1,7-diaminoheptane, norspermidine and norspermine), the data obtained from the linearity, repeatability and recovery experiments were very good for all the compounds assayed. The corresponding limits of detection were invariably below 10 microg l(-1). The method was successfully applied to measure the content of biogenic amines in twelve young and five aged Port wine samples, eleven grape juice samples as well as in ten Portuguese red and white table wines. Results are presented and briefly discussed.     

Geographical origin of Sauvignon Blanc wines predicted by mass spectrometry and metal oxide based electronic nose

Analysis of 34 Sauvignon Blanc wine samples from three different countries and six regions was performed by gas chromatography-mass spectrometry (GC-MS). Linear discriminant analysis (LDA) showed that there were three distinct clusters or classes of wines with different aroma profiles. Wines from the Loire region in France and Australian wines from Tasmania and Western Australia were found to have similar aroma patterns. New Zealand wines from the Marlborough region as well as the Australian ones from Victoria were grouped together based on the volatile composition. Wines from South Australia region formed one discrete class. Seven analytes, most of them esters, were found to be the relevant chemical compounds that characterized the classes. The grouping information obtained by GC-MS, was used to train metal oxide based electronic (MOS-Enose) and mass spectrometry based electronic (MS-Enose) noses. The combined use of solid phase microextraction (SPME) and ethanol removal prior to MOS-Enose analysis, allowed an average error of prediction of the regional origins of Sauvignon Blanc wines of 6.5% compared to 24% when static headspace (SHS) was employed. For MS-Enose, the misclassification rate was higher probably due to the requirement to delimit the m/z range considered.     

Development of a mixed-mode solid phase extraction method and further gas chromatography mass spectrometry for the analysis of 3-alkyl-2-methoxypyrazines in wine

A new method for analysing 3-isopropyl-2-methoxypyrazine, 3-sec-butyl-2-methoxypyrazine and 3-isobutyl-2-methoxypyrazine in wine has been developed and applied to wine. The analytes are extracted from 25 mL of wine in a solid-phase extraction cartridge filled with 60 mg of cation-exchange mixed-mode sorbent. Analytes are recovered with triethylamine in dichloromethane and the organic extract is analysed by GC-SIM-MS using 3-isopropyl-2-ethoxypyrazine as internal standard. The detection limits of the method are in all cases under 1 ng/L, below the olfactory thresholds of the compounds in wine. The repeatability of the method is around 15% for levels in wine of 2 ng/L. Linearity is satisfactory and recoveries are in all cases close to 100% with RSD between 13% and 20%. The method has been applied to the analysis of 12 Chilean white and 8 Spanish red wines. The levels found suggest that 3-alkyl-2-methoxypyrazines can exert a significant sensory contribution to the aroma of Chilean Sauvignon Blanc wines, while most likely they play a nearly negligible role on traditional Ribera and Rioja Spanish red wines.     

Direct determination of glyphosate using hydrophilic interaction chromatography with coulometric detection at copper microelectrode

A simple, rapid, and low-cost coulometric method for direct detection of glyphosate using hydrophilic interaction chromatography is presented. The principle of detection is based on the enhancement of the anodic current of copper microelectrode in the presence of complexing agents, such as glyphosate, with the formation of a soluble Cu(II) complex. Under optimized conditions, the limit of detection (S/R = 3) for glyphosate was 0.1 mg L⁻¹ (0.59 μM) without any preconcentration method. The calibration curve has been found linear in all concentration range tested (from limit of detection to 34 mg L⁻¹) with an excellent correlation coefficient (0.9999). The present method was successfully applied for the determination of glyphosate in fruit juices without any kind of extraction, clean-up, or preconcentration step, with recoveries of 92 and 90% for apple and grape juice, respectively.