Development of high ductility and tensile properties by a two-stage draw of poly(acrylonitrile): Effect of molecular weight

Ultradrawing of atactic poly(acrylonitrile) (PAN) was investigated for a M_v series, ranging 8.0 × 10⁴–2.3 × 10⁶. Samples for the draw were prepared from 0.5–30 wt % solutions of PAN in N,N′-dimethylformamide. The solutions were converted to a gel by quenching from 100 to 0°C. The dried gel films were initially drawn uniaxially by solid-state coextrusion (first-stage draw) to an extrusion draw ratio (EDR) of 16, followed by further tensile draw at 100–250°C (second-stage draw). The maximum total draw ratio (DR_t,max) and tensile properties achieved by two-stage draw increased remarkably with sample M_v. Other factors affecting ductility were the solution concentration from which gel was made and the second-stage draw temperature. The effects of these variables became more prominent with increasing M_v. The temperature for optimum second-stage draw increased with sample M_v. Both the initial gel and the drawn products showed no small-angle X-ray long period scattering maximum, suggesting the absence of a chain-folded lamellae structure, which had been found in our previous study on the drawing of nascent PAN powder. The chain orientation function (f_c) and sample density (ρ_s) increased rapidly with DR_t in the lower range (DR_t < 30) and approached constant values of f_c = 0.980–0.996 and ρ_s = 1.177–1.181 g/cm³, respectively, at higher DR_t > 30–100. The tensile modulus also showed a similar increase with DR_t. The tensile strength increased linearly with DR_t, reaching a maximum, and decreased slightly at yet higher DR_t. The highest modulus of 28.5 GPa and strength of 1.6 GPa were achieved with the highest M_v of 2.3 × 10⁶. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 629–640, 1998     

Melt drawing of ultra‐high molecular weight polyethylene: Comparison of Ziegler‐ and metallocene‐catalyzed reactor powders

The drawing behavior of the ultra‐high molecular weight polyethylene (UHMW‐PE) melts has been studied by comparing the stress/strain curves for two types of samples as polymerized using conventional Ziegler and newer metallocene catalyst systems. Two UHMW‐PE samples, having the same viscosity average molecular weight of 3.3 × 10⁶, but different molecular weight distribution, have been drawn from melt at special conditions. The sample films for drawing were prepared by compression molding of reactor powders at 180°C in the melt. Differences in the structural changes during drawing and resultant properties, ascribable to their broad or narrow molecular weight distribution, were estimated from tensile tests, SEM observations, X‐ray measurements and thermal analyses. The metallocene‐catalyzed sample having narrower molecular weight distribution, could be effectively drawn from the melt up to a maximum draw ratio (DR) of 20, significantly lower than that obtained for the Ziegler‐catalyzed sample, ∼ 50. The stress/strain curves on drawing were remarkably influenced by draw conditions, including draw temperature and rate. However, the most effective draw for both was achieved at 150°C and a strain rate of 5 min⁻¹, independent of sample molecular weight distribution. The efficiency of drawing, as evaluated by the resultant tensile properties as a function of DR, was higher for the metallocene‐catalyzed sample having narrower molecular weight distribution. Nevertheless, the maximum achieved tensile modulus and strength for the Ziegler sample, 50–55 and 0.90 GPa, respectively, were significantly higher than those for the metallocene sample, 20 and 0.65 GPa, respectively, reflecting the markedly higher drawability for the former than the latter. The stress/strain behavior indicated that the origin of differences during drawing from the melt could be attributed to the ease of chain relaxation for the lower molecular weight chains in the melt. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1921–1930, 1999     

Uniaxial drawing of polytetrafluoroethylene virgin powder by extrusion plus cold tensile draw

Polytetrafluoroethylene (PTFE) virgin powder was ultradrawn uniaxially by a two-stage draw. A film, compression molded from powder below the melting temperature (T_m), was initially solid-state coextruded to an extrudate draw ratio (EDR) of 6–20 at an established optimum extrusion temperature of 325°C, near the T_m of 335°C. These extrudates from first draw were found to exhibit the highest ductility at 45–100°C for the second-stage tensile draw, depending on the initial EDR and draw rate. The maximum achievable total draw ratio (DR_{t, max}) was 36–48. Such high ductility of PTFE, far below the T_g (125°C) and T_m, is in sharp contrast to other crystalline polymers that generally exhibit the highest ductility above their T_g and near T_m. The unusual draw characteristics of PTFE was ascribed to the existence of the reversible crystal/crystal transitions around room temperature and the low intermolecular force of this polymer, which leads to a rapid decrease in tensile strength with temperature. The structure and tensile properties of drawn products were sensitive to the initial EDR, although this had no significant influence on DR_t,max. The most efficient and highest draw was achieved by the second-stage tensile draw of an extrudate with the highest EDR 20 at 100°C, as evaluated by the morphological and tensile properties as a function of DR_t. The efficiency of draw for the cold tensile draw at 100°C was a little lower than that for solid-state coextrusion near the T_m. However, significantly higher tensile modulus and strength along the fiber axis at 24°C of 60 ± 2 GPa and 380 ± 20 MPa, respectively, were achieved by the two-stage draw, because the DR_t,max was remarkably higher for this technique than for solid-state coextrusion (DR_t,max = 48 vs. 25). The increase in the crystallite size along the fiber axis (D₀₀₁₅), determined by X-ray diffraction, is found to be a useful measure for the development of the morphological continuity along the fiber axis of drawn products.© 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2551–2562, 1998     

Influence of initial polymer concentration in solution and weight-average molecular weight on the drawing behavior of polyethylenes

The influence of initial polymer concentration in solution (c), weight-average molecular weight (M_ω), and drawing temperature on the solid-state drawing behavior of linear polyethylenes was investigated. Optimum conditions, with respect to maximum attainable draw ratio, are observed in isothermal drawing experiments. Moreover, it is shown that high maximum attainable draw ratios can also be obtained upon multistage drawing of UHMW-PE (ultrahigh-molecular-weight polyethylene, M_ω > 10⁶ g/mol) gel films cast from concentrated solutions. The high maximum attainable draw ratio in combination with the high molecular weight (M_ω > 10⁶ g/mol) and polymer concentration (c = 10% w/v) is of particular interest because it results in tapes or fibers with a high Young's modulus (100 GPa) and tensile strength (2.5–3.5 GPa). It is also shown that the maximum attainable draw ratio of polyethylenes scales with the Bueche parameter (c · M_ω) to the ?0.5 power. This experimental observation indicates that intermolecular interactions not only dominate the rheological properties of polyethylene melts and concentrated solutions, but also strongly influence the solid-state drawing behavior of linear polyethylenes.     

Tensile strength of highly oriented polyethylene. II. Effect of molecular weight distribution

The tensile strength of oriented polyethylene filaments is discussed in relation to molecular weight. Short-term tensile properties at room temperature were obtained in our laboratory and from the literature for polymer samples covering the molecular weight (M _w) range from 54 × 10³ to 4 × 10⁶, and polydispersities ranging from 1.1 to 15.6, oriented by solid-state extrusion, melt spinning/drawing, solution spinning/drawing, and “surface growth.” It was found that both the molecular weight and its distribution markedly affected tensile strength. The breaking stress σ of highly oriented fibers varied with molecular weight roughly as σ ∝, M^0.4, at constant M _w/M _n over the entire range studied. Reduction of polydispersity from 8 to 1.1 by an increase of M _n with M _w approximately constant at 10⁵ increased tensile strength of oriented polyethylene filaments by a factor of nearly 2.     

Solid-State coextrusion of high-density polyethylene. II. Effect of molecular weight and molecular weight distribution

The recently developed technique of solid-state coextrusion for ultradrawing semicrystalline thermoplastics has been applied in the preparation of self-reinforced high-density polyethylene extrudates. The extrudates consist of definite core and sheath phases composed of different molecular weights (M_w) in the range of 60,000–250,000 and different molecular weight distributions (M_w/M_n = 3.0–20). Concentric billets of two different phases were prepared for extrusion by in serting a polyethylene rod within a tubular billet of a different high-density polyethylene followed by melting the two phases to obtain bonding between them. The billet was then split longitudinally to increase extrusion speed and extruded at 120°C, 0.23 GPa through a conical die of extrusion draw ratio 25. Extrudates of high tensile modulus (38 GPa) and strength (0.50 GPa) could be produced in a steady state process at a rate near 0.25 cm/min. The tensile properties of the extrudates from either the single or concentric billets increased with average molecular weight and were insensitive to the molecular weight distribution of the constituent phases. Thermal analysis indicated a high deformation efficiency for the sheath and core phases of the extrudates by the coextrusion technique.     

Synthesis and properties of cross‐linkable high molecular weight fluorinated copolyimides

A series of novel high molecular weight fluorinated co‐polyimides (Co‐PIs) containing styryl side chain based on 1,3‐bis(2‐trifluoromethyl‐4‐aminophenoxy)‐5‐(2,3,4,5‐tetrafluorophenoxy)benzene (6FTFPB) were successfully synthesized. The weight‐average molecular weights (M_ws) and polydispersities of the co‐polyimides were in the range 8.93–10.81 × 10⁴ and 1.33–1.82, respectively. The co‐polyimide film showed excellent solubility in organic solvents, high tensile properties (tensile strength exceeded 91 MPa), excellent optical transparency (cutoff wavelength at 332–339 nm and light transparencies above 89% at a wavelength of 550 nm), and high thermal stability (5% thermal weight‐loss temperature up to 510 °C). The casting and spinning films could be cross‐linked by thermal curing. The cured films show better combination property (including excellent resistance to solvents) than that of co‐polyimides. For instance, the glass transition temperature of Co‐PI‐1 (the molar weight ratio of 6FTFPB was 30%) increased from 217 to 271 °C, the tensile strength enhanced from 94 to 96 MPa, the 5% thermal weight‐loss temperature improved from 514 to 525 °C. Moreover, after cured, Co‐PI‐1 film also has a coefficient of thermal expansion (CTE) value of 60.3 ppm °C^?1, low root mean square surface roughness (R_q) at 4.130 nm and low dielectric constant of 2.60. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 349–359     

Mechanical properties and structure of the zone‐drawn poly(L‐lactic acid) fibers

The zone‐drawing (ZD) method was applied three times to the melt‐spun poly(L ‐lactic acid) (PLLA) fibers of low molecular weight (M_v = 13,100) at different temperatures under various tensions. The mechanical properties and superstructure of the ZD fibers were investigated. The resulting ZD‐3 fiber had a draw ratio of 10.5, birefringence of 37.31 × 10⁻³, and crystallinity of 37%, while an orientation factor of crystallites remarkably increased to 0.985 by the ZD‐1. The Young's modulus and tensile strength of the ZD‐3 fiber respectively attained 9.1 GPa and 275 MPa, and the dynamic storage modulus was 10.4 GPa at room temperature. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 991–996, 1999     

Semi‐perfluoroalkylated perylene diimides for conjugated polymers with high molecular weight and high electron mobility

Perylene diimides (PDIs) and their derivatives are excellent semiconductors, while conjugated polymers based on PDIs have limited applications because of their low electron mobility (μ_e) derived from low molecular weight. The reported maximum number‐average molecular weight (M_n) of related polymers is only 21 kDa because PDIs have very poor solubility due to strong π–π stacking of their big planar conjugated cores. Herein, it is found that suitable semi‐perfluoroalkyl groups could enhance the solubility of PDIs significantly, and a series of semi‐perfluoroalkyl modified conjugated polymers with high molecular weight and electron mobility were synthesized. The maximum M_n reaches 94.8 kDa [P(4C_F8C_H‐PDI‐T2)_HW]. In their space‐charge‐limited current (SCLC) devices, all polymers exhibit typical characters of electron transporting semiconductors, and the highest μ_e is up to 8.40 × 10⁻³ cm² V⁻¹ s⁻¹ [P(4C_F8C_H‐PDI‐T2)_HW], which is similar as that of widely used electron transporting semiconductor PC₆₁BM (6.41 × 10⁻³ cm² V⁻¹ s⁻¹). © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 116–124     

Crystal Transformation and Development of Tensile Properties upon Drawing of Poly(L-lactic acid) by Solid-State Coextrusion: Effects of Molecular Weight

Melt-crystallized films of poly(L -lactic acid) (PLLA) with M_v in the range of 3.8 ∼ 46 × 10⁴ consisting of α-form crystals were uniaxially drawn by solid-state coextrusion. The effects of M_v, extrusion draw ratio (EDR), and extrusion temperature (T_ext) on the crystal/crystal transformation from α- to β-form crystals and the resultant tensile properties of drawn products were studied. The crystal transformation proceeded with EDR and more rapidly for the higher M_v's. Furthermore, the crystal transformation proceeded most rapidly with EDR at a T_ext around 130 °C, independently of the M_v's. As a result of the optimum combination of processing variables influencing the the crystal transformation (M_v, T_ext, and drawability), highly oriented films consisting of β-form crystals alone were obtained by coextrusion of higher M_v samples at T_ext's slightly below the melting temperature (150 ∼ 170 °C) and at higher EDR's > 11. Both the tensile modulus and strength increased rapidly with EDR. The modulus at a given EDR was slightly higher for the samples with higher M_v's. In contrast, the strength at a given EDR was remarkably higher for the higher M _v's. The highest tensile modulus of 8.0 GPa and strength of 500 MPa were obtained with the sample of the highest M_v of 46 × 10⁴ coextruded at 170 °C to the highest EDR of 14.     

Superdrawing of polytetrafluoroethylene nascent powder by solid‐state coextrusion

A film of nascent powder of polytetrafluoroethylene (PTFE), compacted below the ambient melting temperature (T_m, 335 °C), was drawn by two‐stage draw techniques consisting of a first‐stage solid‐state coextrusion followed by a second‐stage solid‐state coextrusion or tensile draw. Although the ductility of extrudates was lost for the second‐stage tensile draw at temperatures above 150 °C due to the rapid decrease in strength, as previously reported, the ductility of extrudates increased with temperature even above 150 °C when the second‐stage draw was made by solid‐state coextrusion, reflecting the different deformation flow fields in a free space for the former and in an extrusion die for the latter. Thus, a powder film initially coextruded to a low extrusion draw ratio (EDR) of 6–20 at 325 °C was further drawn by coextrusion to EDRs up to ～?400 at 325–340 °C, near the T_m. Extremely high chain orientation (f_c = 0.998 ± 0.001), crystallinity (96.5 ± 0.5)%, and tensile modulus (115 ± 5 GPa at 24 °C, corresponding to 73% of the X‐ray crystal modulus) were achieved at high EDRs. Despite such a morphological perfection and a high modulus, the tensile strength of a superdrawn tape, 0.48 ± 0.03 GPa, was significantly low when compared with those (1.4–2.3 GPa) previously reported by tensile drawing above the T_m. Such a low strength of a superdrawn, high‐modulus PTFE tape was ascribed to the low intermolecular interaction of PTFE and the lack of intercrystalline links along the fiber axis, reflecting the initial chain‐extended morphology of the nascent powder combined with the fairly high chain mobility associated with the crystal/crystal transitions at around room temperature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3369–3377, 2006     

Effects of molecular weight of nitrocellulose on structure and properties of polyurethane/nitrocellulose IPNs

Semi‐interpenetrating polymer network (semi‐IPN) coatings were prepared by using castor oil‐based polyurethane (PU) and nitrocellulose (NC) with various viscosity‐average molecular weights (M_η) from 6 × 10⁴ to 42 × 10⁴, and coated on a regenerated cellulose (RC) film to obtain water‐resistant film. The PU/NC coatings and coated films, which were cured at 80°C for 5 min and 2 min, respectively, were investigated by infrared (IR) and ultraviolet (UV) spectroscopy, X‐ray diffraction, swelling test, strength test, dynamic mechanical thermal analysis (DMTA), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The results show that the crosslink densities of the PU/NC semi‐IPNs were smaller than that of pure PU, and decreased with the decrease of M_η of nitrocellulose (NC M_η), indicating NC molecules cohered intimately with PU, and hindered the PU network formation. The physical and mechanical properties of the films coated with PU/NC coatings were significantly improved. With the increase of NC M_η, the strength and thermal stability of the coated films increased, but the pliability, water resistivity, and optical transmission decreased slowly. The PU/NC coating with low NC M_η more readily penetrated into the RC film, and reacted with cellulose, resulting in a strong interfacial bonding and dense surface caused by intimate blend of PU/NC in the coated films. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1623–1631, 1999     

Superdrawing of polytetrafluoroethylene virgin powder above the static melting temperature

A new two‐stage draw technique was successfully applied to the superdrawing of polytetrafluoroethylene (PTFE) virgin powder. A film, compression‐molded from powder below the melting temperature (T_m = 335 °C), was initially solid‐state coextruded to an extrusion draw ratio (EDR) of 6–20 at 325 °C, about 10 °C below the T_m. These extrudates from the first‐stage draw were further drawn by a second‐stage pin draw in the temperature (T_d) range of 300–370 °C that covers the static T_m. The maximum achievable total draw ratio was ～60 at a T_d = 300 °C and increased rapidly with increasing T_d, reaching a maximum of 100–160 at a temperature window between 340 and 360 °C, depending on the initial EDRs. At yet higher T_d's, the ductility was lost as a result of melting. The high ductility of the PTFE extrudates at such high temperatures was ascribed to the improvement of interfacial adhesion and bonding between the deformed powder particles upon the first‐stage extrusion combined with the rapid heating of only a portion of the extrudate followed by the elongation at a high rate. The highly drawn fibers were highly crystalline (χ_c ≤ 87%) and showed high chain orientation (f_c ≤ 0.997) and a large crystallite size along the chain axis (D₀₀₁₅ ≤ 160 nm). The molecular draw ratio, estimated from the entropic shrinkage above the T_m, was close to the macroscopic deformation ratio independently of the initial EDRs. These results indicate that the draw was highly efficient in terms of chain extension, orientation, and crystallization. Thus, the maximum tensile modulus and strength achieved in this work were 102 ± 5 and 1.4 ± 0.2 GPa, respectively, at 24 °C. These tensile properties are among the highest ever reported on oriented PTFE. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1995–2004, 2001     

Initiator efficiency of 2,2′‐azobis(isobutyronitrile) in bulk dodecyl acrylate free‐radical polymerizations over a wide conversion and molecular weight range

An Erratum has been published for this article in J. Polym. Sci. Part A: Polym. Chem. (2004) 42(21) 5559 . The initiator efficiency, f, of 2,2′‐azobis(isobutyronitrile) (AIBN) in dodecyl acrylate (DA) bulk free‐radical polymerizations has been determined over a wide range of monomer conversion in high‐molecular‐weight regimes (M_n ? 10⁶ g mol^?1 [? 4160 units of DA)] with time‐dependent conversion data obtained via online Fourier transform near infrared spectroscopy (FTNIR) at 60 °C. In addition, the required initiator decomposition rate coefficient, k_d, was determined via online UV spectrometry and was found to be 8.4 · 10^?6 s^?1 (±0.5 · 10^?6 s^?1) in dodecane, n‐butyl acetate, and n‐dodecyl acetate at 60 °C. The initiator efficiency at low monomer conversions is relatively low (f = 0.13) and decreases with increasing monomer to polymer conversions. The evolution of f with monomer conversion (in high‐molecular‐weight regimes), x, at 60 °C can be summarized by the following functionality: f^{60 °C} (x) = 0.13–0.22 · x + 0.25 · x² (for x ≤ 0.45). The reported efficiency data are believed to have an error of >50%. The ratio of the initiator efficiency and the average termination rate coefficient, 〈k_t±, (f/〈k_t〉) has been determined at various molecular weights for the generated polydodecyl acrylate (M_n = 1900 g mol^?1 (? 8 units of DA) up to M_n = 36,500 g mol^?1 (? 152 units of DA). The (f/〈k_t〉) data may be indicative of a chain length‐dependent termination rate coefficient decreasing with (average) chain length. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5170–5179, 2004     

Synthesis of periodic copolymers via ring‐opening copolymerizations of cyclic anhydrides with tetrahydrofuran using nonafluorobutanesulfonimide as an organic catalyst and subsequent transformation to aliphatic polyesters

To synthesize polyesters and periodic copolymers catalyzed by nonafluorobutanesulfonimide (Nf₂NH), we performed ring‐opening copolymerizations of cyclic anhydrides with tetrahydrofuran (THF) at 50–120 °C. At high temperature (100–120 °C), the cyclic anhydrides, such as succinic anhydride (SAn), glutaric anhydride (GAn), phthalic anhydride (PAn), maleic anhydride (MAn), and citraconic anhydride (CAn), copolymerized with THF via ring‐opening to produce polyesters (M_n = 0.8–6.8 × 10³, M_n/M_w = 2.03–3.51). Ether units were temporarily formed during this copolymerization and subsequently, the ether units were transformed into esters by chain transfer reaction, thus giving the corresponding polyester. On the other hand, at low temperature (25–50 °C), ring‐opening copolymerizations of the cyclic anhydrides with THF produced poly(ester‐ether) (M_n = 3.4–12.1 × 10³, M_w/M_n = 1.44–2.10). NMR and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectra revealed that when toluene (4 M) was used as a solvent, GAn reacted with THF (unit ratio: 1:2) to produce periodic copolymers (M_n = 5.9 × 10³, M_w/M_n = 2.10). We have also performed model reactions to delineate the mechanism by which periodic copolymers containing both ester and ether units were transformed into polyesters by raising the reaction temperature to 120 °C. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Influence of molecular weight on the phase behaviors of comb‐like polymers with long n‐alkyl side chains based on mesogen‐jacketed liquid crystalline polymers

A series of comb‐like polymers, poly{2,5‐bis[(4‐octadecyloxyphenyl)oxycarbonyl]‐styrenes{ (P‐OC18s) with different molecular weights (M_n) and low molecular weight distributions have been successfully synthesized via atom transfer radical polymerization. The phase behaviors have been investigated by a combination of techniques including differential scanning calorimetry, polarized optical microscopy, wide‐angle X‐ray diffraction, and temperature‐variable FTIR spectroscopy. One hand, phase behaviors of the alkyl tails were strongly influenced by the mesogens of polymers, leading to the poor packing of the alkyl tails and the low melting. The other hand, the liquid crystalline phase structures of polymers were found to be strongly M_n dependent. The samples with M_n ≤ 4.6 × 10⁴ formed a smectic phase in low temperature and an isotropic phase in high temperature. The samples with M_n ≥ 5.2 × 10⁴ displayed a reentrant isotropic phase, which was separating the smectic phase and columnar nematic phase. Meantime, the experiment results showed that the glass temperature and the transition temperature from smectic phase to isotropic phase both slightly increased with the increase of M_nS; however, the transition temperature from isotropic phase to columnar phase sharply decreased with the M_nS improved. The reappearance of isotropic phase is due to the competing between the driving force of the enthalpy and the driving force of the entropy. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Cationic copolymerization of indene with styrene derivatives: Synthesis of random copolymers of indene with high molecular weight

Random copolymers with high molecular weights of indene and p‐methylstyrene (pMeSt) were synthesized by cationic polymerization with trichloroacetic acid/tin tetrachloride in CH₂Cl₂ at low temperatures. When indene and pMeSt (1:1 v/v), for example, were polymerized at ?40 °C, both monomers were consumed at very similar rates to give a copolymer with high molecular weight [number‐average molecular weight (M_n): 8–9 × 10⁴]. This is indeed quite unexpected behavior for the combination of these two monomers because pMeSt polymerized over 1000 times faster than indene in the homopolymerization under the reaction conditions previously described. The product copolymer of indene and pMeSt had a random monomer sequence in it that was confirmed by NMR analyses and thermal‐property measurements. In sharp contrast with pMeSt, styrene and p‐chlorostyrene, which have no electron‐donating groups on the phenyl ring, led to low molecular weight polymers (M_n < 10,000) in the copolymerization with indene (1:1 v/v). © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2449–2457, 2002     

Structure and properties of chlorinated polyvinyl chloride graft copolymer with higher property

In this work, maleic anhydride (MAH) was grafted onto chlorinated polyvinyl chloride (CPVC) with high chlorine content (66 wt%) via in‐situ chlorinating graft copolymerization (ISCGC) to obtain the material with improved mechanical strength, softening point, and thermal stability of the material. The structure of the graft product (CPVC‐cg‐MAH) was characterized by FTIR, ¹H NMR, GPC, and UV. CPVC‐cg‐MAH contains less vinylidene chloride (CCl₂) units and double bond than corresponding CPVC. Meanwhile, the number–average molecular weight (M_n) and weight–average molecular weight (M_w) of CPVC‐cg‐MAH are increased, but distribution of molecular weight (M_w/M_n) is decreased. Then, the tensile strength and notched impact strength of CPVC‐cg‐MAH increased by 14.5 and 34.6%, respectively. Furthermore, the results of DMA, DSC, TG, and Vicat softening point showed that the loss peak of CPVC‐cg‐MAH was higher evidently than CPVC and moved to high temperature, the glass transition temperature (T_g) of CPVC‐cg‐MAH was consistent with CPVC, initial weight loss temperature, and maximum weight loss rate temperature of CPVC‐cg‐MAH increased by 7.2°C and 6.1°C, respectively, and the Vicat softening temperature of CPVC‐cg‐MAH increased by 15°C and up to 130°C. Copyright © 2011 John Wiley & Sons, Ltd.     

Studies on Macromolecular Complexing Agents. II. Effects of Polypropylene Oxide on the Copolymerization Reaction between Butadiene and Styrene

ABSTRACT

Ultra-high-molecular-weight poly[(R)-3-hydroxybutyrate](P(3HB)) was biosynthesized from glucose by a recombinant Escherichia coli XL-1 Blue (pSYL105) harboring Alcaligenes eutrophus PHB biosynthesis phbCAB genes. Six kinds of P(3HB) samples with differ-ent weight-average molecular weight (M_w ) from 1.1 × 10⁶ to 11 × 10⁶ measured by multi-angle laser light scattering were respectively produced at pH values of 7.0 to 6.5 in culture media. Solvent-cast P(3HB) films of high-molecular-weights over M_w of 3.3 × 10⁶ were stretched easily and reproducibly at 160°C to a draw ratio of 400-650%. Mechanical properties of the stretched P(3HB) films were markedly improved relative to those of solvent-cast film. The elongation to break, Young's modulus, and tensile- strength of stretched film (M_w = 11 × 10⁶) were 58%, 1.1 GPa, and 62 MPa, respectively. X-ray diffraction patterns indicated that the stretched film was highly oriented and had a high crystallinity over 80%. When the stretched film was annealed at 160°C for 2 hours, the mechanical properties were further improved (elongation to break = 67%, Young's modulus = 1.8 GPa and tensile strength = 77 MPa). The mechanical properties of the stretched-annealed film remained almost unchanged for 6 months at room temperature, suggesting that a high crystallinity of the stretched-annealed film avoids a progress of secondary crystallization.

     

Synthesis of poly(p‐phenylene) macromonomers and multiblock copolymers

Rigid‐rod poly(4′‐methyl‐2,5‐benzophenone) macromonomers were synthesized by Ni(0) catalytic coupling of 2,5‐dichloro‐4′‐methylbenzophenone and end‐capping agent 4‐chloro‐4′‐fluorobenzophenone. The macromonomers produced were labile to nucleophilic aromatic substitution. The molecular weight of poly(4′‐methyl‐2,5‐benzophenone) was controlled by varying the amount of the end‐capping agent in the reaction mixture. Glass‐transition temperatures of the macromonomers increased with increasing molecular weight and ranged from 117 to 213 °C. Substitution of the macromonomer end groups was determined to be nearly quantitative by ¹H NMR and gel permeation chromatography. The polymerization of a poly(4′‐methyl‐2,5‐benzophenone) macromonomer [number‐average molecular weight (M_n) = 1.90 × 10³ g/mol; polydispersity (M_w)/M_n = 2.04] with hydroxy end‐capped bisphenol A polyaryletherketone (M_n = 4.50 × 10³ g/mol; M_w/M_n = 1.92) afforded an alternating multiblock copolymer (M_n = 1.95 × 10⁴ g/mol; M_w/M_n = 6.02) that formed flexible, transparent films that could be creased without cracking. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3505–3512, 2001