Optimization of Plant Sample Preparation and ICP Parameters for Analysis of Phosphorus

Abstract

Parameters of HNO₃-H₂O₂ wet digestion sample preparation method and inductively coupled plasma atomic emission spectrometer     

Analytical performance of a multi-element ICP-AES method for Cd, Co, Cr, Cu, Mn, Ni and Pb determination in blood fraction samples

An analytical method using inductively coupled plasma atomic emission spectrometry (ICP-AES) for rapid simultaneous determination of seven heavy metals (Cd, Co, Cr, Cu, Mn, Ni and Pb) in human blood fractions, like plasma, cells fraction and whole blood, is performed. The optimum wavelength was selected using as criterions the sensitivity, the linearity and recovery of aqueous standard solutions. The pretreatment of the sample, the centrifugal conditions, the necessity of digestion and the dilution of the digests were also studied. For plasma it was possible to avoid digestion of the sample, but for cells fractions and whole blood the digestion is necessary. The samples were acid-digested by HNO₃ in closed Teflon tubes under high temperature and pressure conditions and were diluted before injection into ICP-AES. Also, optimization of the inductively coupled plasma conditions like nebulizer argon flow rate, sample flow rate and power of radio frequency was performed for each analyte. Finally, the effect of the type of the employed calibration technique on the total variation of the method was examined. Calibration using the standard addition technique was proved more accurate for the determination in terms of analyte recovery. The sensitivity and recovery (Cd 99%, Co 101%, Cr 100%, Cu 99%, Mn 101%, Ni 100% and Pb 97%) of the developed method are presented for all examined blood fractions. Correspondence: George A. Zachariadis, Laboratory of Analytical Chemistry, Department of Chemistry, Aristotle University, Thessaloniki 54124, Greece     

Determination of Titanium in Nano-Titanium(IV) Oxide Composite Food Packaging by Microwave Digestion and Inductively Coupled Plasma Atomic Emission Spectrometry and Inductively Coupled Plasma Mass Spectrometry

Titanium was determined in nano-titanium(IV) oxide food packaging by microwave digestion with inductively coupled plasma atomic emission spectrometry (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS). Microwave digestion was optimized using different acid combinations. Both spectrometry techniques showed good reproducibility, repeatability, and recovery. For ICP-AES, the limit of detection was 5.0 mg kg^?1, the linear dynamic range was 100–5000 µ g L^?1, the average recoveries for blank samples spiked with titanium were between 94.7% and 100.1%, and the relative standard deviations were from 2.1% to 7.1%. By ICP-MS, the limit of detection was 0.3 mg kg^?1, the linear dynamic range was 0.5–200 µ g L^?1, the recoveries were 88.4%–96.3%, and the relative standard deviations were 6.3%–7.4%. These results indicated that methods were effective for the determination of titanium in food packaging.     

Inductively coupled plasma – Tandem mass spectrometry (ICP-MS/MS): A powerful and universal tool for the interference-free determination of (ultra)trace elements – A tutorial review

This paper is intended as a tutorial review on the use of inductively coupled plasma – tandem mass spectrometry (ICP-MS/MS) for the interference-free quantitative determination and isotope ratio analysis of metals and metalloids in different sample types. Attention is devoted both to the instrumentation and to some specific tools and procedures available for advanced method development. Next to the more typical reaction gases, e.g., H₂, O₂ and NH₃, also the use of promising alternative gases, such as CH₃F, is covered, and the possible reaction pathways with those reactive gases are discussed. A variety of published applications relying on the use of ICP-MS/MS are described, to illustrate the added value of tandem mass spectrometry in (ultra)trace analysis.     

Development of cadmium/silver/palladium separation by ion chromatography with quadrupole inductively coupled plasma mass spectrometry detection for off-line cadmium isotopic measurements

A separation method was investigated to perform off-line cadmium isotopic measurements on a ¹⁰⁹Ag transmutation target. Ion chromatography (IC) with Q ICPMS detection (quadrupole inductively coupled plasma mass spectrometry detection) was chosen to separate cadmium from the isobarically interfering elements, silver and palladium, present in the sample. The optimization of chromatographic conditions was particularly studied. Several anion and cation columns (Dionex AG11^®, CS10^® and CS12^®) were compared with different mobile phases (HNO₃, HCl). The separation procedure was achieved with a carboxylate-functionalized cation exchange CS12 column using 0.5 M HNO₃ as eluent. The developed technique yielded satisfactory results in terms of separation factors (greater than 5) and provides an efficient solution to obtain rapidly purified cadmium fractions (decontamination factors higher 100,000 for silver and palladium) which can directly be analyzed by multi collection inductively coupled plasma mass spectrometry (MC ICPMS). By applying the proposed procedure, accurate and precise cadmium isotope ratios were determined for the irradiated ¹⁰⁹Ag transmutation target.     

Investigation of four digestion procedures for multi-element determination of toxic and nutrient elements in legumes by inductively coupled plasma-optical emission spectrometry

A simple and reliable multi-element procedure for determination of essential (Cr, Cu, Fe, Mg, Mn, Zn) and toxic (Al, Cd, Pb) elements in legumes by inductively coupled plasma-optical emission spectrometry (ICP-OES) was developed. In this contribution, four different digestion procedures were thoroughly investigated and accurately evaluated with respect to their affect on the analysis of legumes. These included wet digestion with HNO₃/H₂SO₄ and HNO₃/H₂SO₄/H₂O₂, and dry ashing with Mg(NO₃)₂ and Mg(NO₃)₂/HNO₃. Two calibrations (aqueous standard and standard addition) procedures were studied, and proved that standard addition was preferable for all analytes. ICP-OES operating parameters, such as radio-frequency (RF) incident power, sample uptake flow rate and nebulizer argon gas flow rate were optimized. The precision as repeatability, expressed as relative standard deviation (R.S.D.) for aqueous standard containing 250 μg l⁻¹ of each analyte was in the range1.5-8.0%. The accuracy, expressed as relative error was generally varied in the range of 0.5-10% for all analytes, while the quantification limits were lower than 2.5 μg g⁻¹. Although, acceptable results were obtained from all developed procedures, wet digestion method with HNO₃/H₂SO₄/H₂O₂ is recommended for better recovery. The good agreement between measured and certified concentrations with respect to IAEA-331 and IAEA-359 (CRM's supplied by IAEA, International Atomic Energy Agency) indicates that the developed analytical method is well suited for determination of toxic and nutrient elements in legumes and possibly similar matrices.     

Determination of metal concentrations in lichen samples by inductively coupled plasma atomic emission spectroscopy technique after applying different digestion procedures

Three digestion procedures have been tested on lichen samples for application in the determination of major, minor and trace elements (Al, Ca, Cd, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, Pb, V and Zn) in lichen samples collected in Aegean Region of Turkey by inductively coupled plasma atomic emission spectrometer (ICP-AES). The acid mixture of concentrated HNO₃, H₂O₂ and HF were used. The instrument was optimized using lichen matrix considering RF power, nebulizer pressure, auxiliary flow rate and pump rate. The accuracy of the overall analyses was first estimated by analysis of two certified reference materials. Good agreement between measured and reference values were found for almost all elements. As the second way of determining the accuracy, results obtained from independent analytical techniques (ICP-AES and instrumental neutron activation analysis (INAA)) were compared for all elements by analyzing real samples. Correlation coefficients of two techniques for the elements ranged between 0.70 (Mg) and 0.96 (Fe). Among the three digestion systems, namely microwave, open vessel and acid bomb, microwave digestion system gave the best recovery results. The method detection limit (MDL) was computed using reagent blanks of microwave digestion system since it provides cleaner sample preparation. Detection limit is adequate for all elements to determine the elements in lichen samples. The precision was assessed from the replicate analyses of reagent blanks of microwave digestion system and was found to be less than 1.5% relative standard deviation (R.S.D.).     

Determination of chromium, iron and selenium in foodstuffs of animal origin by collision cell technology, inductively coupled plasma mass spectrometry (ICP-MS), after closed vessel microwave digestion

The determination of chromium (⁵²Cr), iron (⁵⁶Fe) and selenium (⁸⁰Se) isotopes in foodstuffs of animal origin has been performed by collision cell technology (CCT) mode using an inductively coupled plasma mass spectrometry (ICP-MS) as detector after closed vessel microwave digestion. To significantly decrease the argon-based interferences at mass to charge ratios (m/z): 52 (⁴⁰Ar¹²C), 56 (⁴⁰Ar¹⁶O) and 80 (⁴⁰Ar⁴⁰Ar), the gas-flow rates of a helium and hydrogen mixture used in the hexapole collision cell were optimised to 1.5 ml min⁻¹ H₂ and 0.5 ml min⁻¹ He and the quadrupole bias was adjusted daily between −2 and −15 mV. Limits of quantification (LOQ) of 0.025, 0.086 and 0.041 mg kg⁻¹ for Cr, Fe and Se, respectively, in 6% HNO₃ were estimated under optimized CCT conditions. These LOQ were improved by a factor of approximately 10 for each element compared to standard mode.Precision under repeatability, intermediate precision reproducibility and trueness have been tested on nine different certified reference materials in foodstuffs of animal origin and on an external proficiency testing scheme. The results obtained for chromium, iron and selenium were in all cases in good agreement with the certified values and trueness was improved, compared to those obtained in standard mode.     

Microwave-assisted total digestion of sulphide ores for multi-element analysis

A new two-stage microwave-assisted digestion procedure using concentrated HNO₃, HCl, HF and H₃BO₃ has been developed for the chemical analysis of major and trace elements in sulphide ore samples prior to inductively coupled plasma atomic emission spectroscopy (ICP-AES) analysis. In the first stage 0.2 g of the certified reference material (CRM) sample was digested with a combination of acids (HNO₃, HCl, and HF) in a closed Teflon vessel and heated in the microwave to 200 °C for 30 min. After cooling, H₃BO₃ was added and the vessel was reheated to 170 °C for 15 min. The precision of the method was checked by comparing the results against six certified reference materials. The analytical results obtained were in good agreement with the certified values, in most cases the recoveries were in the range 95-105%. Based on at least 17 replicates of sample preparation and analysis, the precision of the method was found to be ≤5%.     

Pre-concentration of Cd, Co, Cu, Ni and Zn using different off-line ion exchange procedures followed by the inductively coupled plasma atomic emission spectrometric detection

The chelating resin Metalfix Chelamine and the strong cation exchanger Dowex 50W-X4 were studied for the off-line pre-concentration of Cd, Co, Cu, Ni and Zn prior to the measurements by the inductively coupled plasma atomic emission spectrometry. Different approaches to the recovery of metals were investigated and compared: the elution with the solutions of HCl and HNO₃ and the decomposition of the resins with the adsorbed metals by means of the high-pressure microwave assisted system. Due to the problem arisen with the quantitative elution of the metals from the resins, which bound the analytes very strongly, the procedure of the digestion of the resin after the pre-concentration step was preferable to the plain elution, giving significantly better recoveries of the metals. The chosen procedure was applied for the determination of traces of Cd, Co, Cu, Ni and Zn in beer. For the analysis, mineralised and not mineralised beer samples were treated with Dowex 50W-X4 resin in order to assess the total content of Cd, Co, Cu, Ni and Zn and the fraction of the cationic labile species of the analytes, respectively. The increase in the sensitivity allowed determination of the selected metals at concentrations of order of 1 ng ml⁻¹. The accuracy of the entire procedure was verified by the recovery test in the spiked samples of beer. The proposed method provides full recovery for Cd (101±1%), Co (99±2%) and Zn (106±3%) and reasonably high recovery for Cu (84±1%) and Ni (89±1%).     

Simultaneous Determination of Trace Elements in Hepatocellular Carcinoma Tissue by Sector Field Inductively Coupled Plasma Mass Spectrometry

An analytical method using sector field inductively coupled plasma mass spectrometry (SF-ICP-MS) for rapid simultaneous determination of Na, Mg, K, Ca, Cr, Mn, Fe, Co, Ni, Cu, Zn, Se, Sr, Mo, and Cd elements in hepatocellular carcinoma (HCC) tissue is reported. The sample was dissolved in HNO₃ and H₂O₂ by microwave digestion and then the aforementioned 15 elements in the solution were analyzed directly by SF-ICP-MS. Most of the spectral interferences were avoided by measuring in medium resolution mode (MRM, M/?M = 4400) and high resolution mode (HRM, M/ΔM = 8000). Correction for matrix effects was made using Sc and Rh as internal standards. The optimum conditions for the determination were tested and discussed. The results showed that SF-ICP-MS is a useful tool for simultaneous determination of multi-elements in HCC tissue and could be widely used in other biological samples analysis.     

Optimization and comparison of two digestion methods for multi-element analysis of certified reference plant materials by ICP-AES. Application of Plackett-Burman and central composite designs

Two open-vessel wet digestion methods using mixtures of (i) HNO₃ and H₂SO₄ (WD I), and (ii) HNO₃, H₂SO₄ and H₂O₂ (WD II) were developed and optimized for determination of a wide range of elements in plant reference materials by inductively coupled plasma atomic emission spectrometry. A Plackett-Burman fractional factorial experimental design with eight experiments for seven variables was used for the evaluation of the effects of several digestion variables at once. From these studies, certain variables showed up as significant, and they were further optimized by using a star-type central composite experimental design, which involved fourteen experiments. Instrumental variables such as radio-frequency incident power, nebulizer argon gas flow rate and sample uptake flow rate were also optimized. The analytical performance was assessed statistically. Nine elements in total can be simultaneously determined at the concentration levels usually found in plant materials. The agreement between measured and certified values with respect to NIST-SRM 1568a (rice flour), IAEA-331 (spinach leaves) and IAEA-359 (cabbage) proved that the developed methods are well suited for routine elemental analysis of plants or foods of plant origin. Correspondence: George A. Zachariadis, Laboratory of Analytical Chemistry, Department of Chemistry, Aristotle University, GR-54124 Thessaloniki, Greece     

Determination of Zn, B, Fe, Mg, Ca, Na and Si in anisette samples by inductively coupled plasma atomic emission spectrometry

A comparative study of several digestion methods of anisette samples has been carried out. Two dry ashing (DA) treatments as well as four wet ashing (WA) procedures using different mixtures of acids were applied for the sample mineralisation before analysis. Once the anisette samples were mineralised, the contents of Zn, B, Fe, Mg, Ca, Na and Si were determined by inductively coupled plasma-atomic emission spectrometry (ICP-AES). Each method has been studied statistically and also attending to their feasibility. After performing the optimisation of the different treatments tested, it was concluded that one wet ashing method employing a HNO₃:H₂O₂ (10:1) mixture was the most suitable. This method was applied to the analysis of anisette samples. Na, Ca, Mg and Si were present in concentrations up to 215 mg l⁻¹ for Na, 11.6 for Mg, 6.2 for Ca and 5.1 for Si. Fe and B concentrations were not higher than 0.12 mg l⁻¹ and lower for Zn.     

Enhanced flow injection leaching of rocks by focused microwave heating with in-line monitoring of released elements by inductively coupled plasma mass spectrometry

A focused microwave digestion system was used to heat a mini-column of sample of crushed rock (hematite) during its successive leaching by repeated 250-μL injections of water, HNO₃ 1%, 10% and 30% (v/v). The mini-column was connected to the nebulizer of an inductively coupled plasma mass spectrometry instrument, which allowed a continuous monitoring of the progressive release of elements by a given leaching reagent. Quantitation of the accessible fraction of Mg, V, Cr, Mn, Co, Ni, Cu, Zn, Mo, Sb and Pb was done by calibration using 250-μL injections of standard solutions prepared in the leaching reagent matrices. Total digestion of the sample residue was also done to verify mass balance. With the exception of Mg, V and Co, where the same total amount was released with or without microwave heating, an increased release resulted from focused microwave heating, by up to an order of magnitude. Furthermore, mass balance was verified for more elements using microwave heating, presumably because of a lower relative proportion of spectroscopic interference as a result of an increased release of analytes. Using microwave energy in general resulted in the dissolution of additional phases, as evidenced by significantly different ²⁰⁸Pb/²⁰⁶Pb ratios as well as the increased release of elements with milder reagents. In fact, in the case of Pb, leaching with 30% HNO₃ was no longer necessary as all the Pb was released in the first three leaching reagents. Microwave heating could therefore be used advantageously in on-line leaching for exploration geochemistry and environmental monitoring.     

Comparison of open digestion methods and selection of internal standards for the determination of Rh,Pd and Pt in plant samples by ICP-MS

An analytical procedure for the reliable determination of Pd, Pt and Rh in plant samples by inductively coupled plasma-mass spectrometry (ICP-MS) was developed. An ultrasonic nebulizer (USN) was used for sample introduction to improve sensitivity. Under various synthetic plant sample matrix compositions, it was established experimentally that moderate amounts (0.2–2%) of dissolved solids decreased the analyte signals significantly. Internal standardisation with In (for Pd and Rh) and Ir (for Pt) proved to be essential for obtaining correct results. Five open digestion approaches, used for converting solid plant samples to aqueous solution, were also tested for the purpose, namely dry-ashing, dry-ashing followed by HF attack, wet digestion with H₂O₂–HNO₃, wet digestion followed by HF attack and aqua regia digestion. Recovery tests in two spiked plant materials showed that only wet digestions must be used. With these ways, all PGEs could be reliably quantified by USN-ICP-MS without applying a separation or preconcentration step with a good precision (below 10% RSD). The aqua regia procedure was applied to the determination of PGEs in various plant matrices collected along a highway. Results showed that mosses were probably the best choice of samples to monitor the bioaccumulation of PGEs in time.     

Characterization of Geological Certified Reference Materials by Inductively Coupled Plasma-Mass Spectrometry

A rapid, safe, and efficient microwave-assisted acid digestion method is reported to determine thirty-six elements in three international geological reference materials and two in-house reference materials using high resolution inductively coupled plasma mass spectrometry. This method was also employed to determine the radiogenic isotopic composition of Sr and Nd in two geological reference materials by multicollector inductively coupled plasma mass spectrometry. In order to ascertain the most suitable preparation method, four microwave-assisted digestion procedures were compared. The presence of insoluble fluorides on the recoveries of Ba, Rb, Sr and rare earth elements was resolved through sequential evaporation at 80 degrees Celsius followed by microwave digestion. Digestion methods without using HClO₄ or H₃BO₃ and using only H₃BO₃ were unsuitable due to lower recoveries and higher procedural blanks, respectively. Digestion methods that involved the use of HCl-HNO₃-HF and HCl-HNO₃-HF-HClO₄ were most suitable, resulting in better recoveries of the elements. However, the HCl-HNO₃-HF method was preferred compared to HCl-HNO₃-HF-HClO₄ because the former avoids the use of HClO₄ and thus was used in measurements of the radiogenic isotopes of Sr and Nd. The optimized method was used to verify the reference values for the isotopic compositions of Sr and Nd in geological standard reference materials.     

Simple,fast, and low-contamination microwave-assisted digestion procedures for the determination of chemical elements in biological and environmental matrices by sector field ICP-MS

A simple and convenient method for the digestion of animal tissues, lichens, and plants for 33 metals measured by sector field inductively coupled plasma mass spectrometry (SF-ICP-MS) was described. Microwave-assisted acid digestions were performed at atmospheric pressure by means of a multi-samples rotor designed for processing a large number of samples at once in screw-capped disposable polystyrene liners. The digested samples were filled up to final volume directly in the polystyrene liners ready for elemental quantification. Seven certified reference materials, namely BCR 184 (bovine muscle), BCR 186 (pig kidney), DORM-2 (dogfish muscle), BCR 422 (cod muscle), BCR 62 (olive leaves), BCR 100 (beech leaves), and BCR 482 (lichen) were analysed to verify the accuracy of the method. The linearity range, limit of quantification, precision, and recovery by addition of non-certified elements were also assessed. All elements, with the exception of Hg in BCR 184 and As in BCR 186, were above the quantification limit and blank concentrations, and good agreement existed between found and target values in bovine muscle, pig kidney, and cod muscle. Significant deviations were observed for Al, Co, Cr, Mn, and Ni in dogfish muscle and for Ca, Cr, Fe, and Hg in lichens and plants. The proposed digestion procedure offers a low contamination risk, simplicity, speed, low cost, and applicability in routine analysis, and the SF-ICP-MS method allowed metals from a fraction of ng?g^?1 to hundreds of µg?g^?1 to be quantified in one analytical run.     

Determination of cadmium, lead, iron, nickel and chromium in selected food matrices by plasma spectrometric techniques

In the frame of a study aimed at investigating the transfer of metal contaminants through the food chain and the effects of food processing, five elements, namely Cd, Pb, Fe, Ni and Cr, were accurately determined in (i) durum wheat grain and derived products, (ii) wheat-based reference materials, (iii) drinking water, used both as an ingredient and for technological purposes in the investigated industrial process. Microwave closed vessel digestion was selected as the dissolution technique for solid samples, whereas water samples were acidified with ultrapure nitric acid and analysed directly. As several analytes had to be quantified at trace or ultratrace levels, inductively coupled plasma mass spectrometry (ICP-MS) was resorted to for analytical determinations. Overall, this straightforward analytical approach enabled to detect the often small changes in element concentration associated with the different technological steps of processing. Nevertheless, detection of heavily interfered elements, especially Cr, as well as analyte quantification at ultratrace-level level in water, posed analytical challenges that required suited analytical solutions.Changes in the sample introduction system and complementary use of inductively coupled plasma atomic emission spectrometry (ICP-AES) straightforwardly overcame the difficulties in determining the analytes in the selected food matrixes. The benefits of ultrasonic nebulization in reducing the effects of problematic spectral interferences were demonstrated. Overall, a robust and high-throughput analytical method was outlined.     

Trace Determination of Manganese in Urine by Graphite Furnace Atomic Absorption Spectrometry and Inductively Coupled Plasma–Mass Spectrometry

This paper describes a simple and sensitive method for the determination of manganese in human urine by graphite furnace atomic absorption spectroscopy (GFAAS), which includes sample preparation by microwave digestion. Matrix modifier combinations, the digestion power, pyrolysis, and atomization temperatures were optimized. A mixture of 5.0 µg Pd(NO₃)₂ and 3.2 µg Mg(NO₃)₂ modifier presented the best performance. The optimal temperatures for pyrolysis and atomization were 1500°C and 1950°C, respectively. The GFAAS method was compared to inductively coupled plasma–mass spectrometry (ICP–MS) for the determination of manganese in urine. Analytical figures of merit for GFAAS and ICP–MS were: accuracy (3.46%, 2.19%), precision (3.61%, 5.84%), LOD (0.109 µg · L^?1, 0.015 µg · L^?1), LOQ (0.327 µg · L^?1, 0.045 µg · L^?1), and recovery (80–100%, 74–89%). Both methods were employed for the determination of Mn in urine and the results were compared statistically.     

A pilot study on the feasibility of the preparation of a new certified reference material based on the Antarctic Scallop Adamussium Colbecki

As foreseen by the Italian National Programme of Research in Antarctica, a preliminary investigation was performed to ascertain the feasibility of the production of a new Certified Reference Material for trace elements based on the bivalve Adamussium colbecki. The scallops sampled in Antarctica during the 1999–2000 Italian scientific expedition were analyzed by inductively coupled plasma atomic emission spectrometry and high-resolution inductively coupled plasma mass spectrometry for their content in selected trace elements (As, Cd, Cr, Cu, Fe, Hg, Mn, Mo, Ni, V and Zn). The certification campaign will be undertaken on the basis of the findings of this feasibility study in close cooperation with the Institute for Reference Materials and Measurements, Joint Research Centre of the European Commission.