新型锌铝水滑石紫外吸收剂的制备及其紫外吸收性能

以有机紫外吸收剂2-苯基苯并咪唑-5-磺酸(PBSA)、N,N-二甲氨基苯甲酸(DABA)为有机原料,采用共沉淀法,合成了有机紫外吸收剂插层水滑石Zn2Al-LDH/PBSA和Zn2Al-LDH/DABA,并测定了所得到的样品的XRD、FT IR、薄膜紫外吸收性质和氧化催化活性。结果表明,当有机紫外吸收剂以阴离子的形式进入水滑石层间后,仍有良好的紫外吸收性能并在可见光区有很好的透光性;通过测定插层水滑石的氧化催化活性,与纯有机物相比,Zn2Al-LDH/PBSA和Zn2Al-LDH/DABA的氧化催化活性明显降低。合成的新型的插层水滑石有望在防晒产品中得到应用。     

新型锌铝水滑石紫外吸收剂的制备和紫外性能研究

以有机紫外吸收剂2-苯基苯并咪唑-5-磺酸(PBSA)、N,N-二甲氨基苯甲酸(DABA)为有机原料,采用共沉淀法,合成了有机紫外吸收剂插层水滑石Zn2Al-LDH/PBSA和Zn2Al-LDH/DABA,并测定了所得到的样品的XRD、FT IR、薄膜紫外吸收性质和氧化催化活性。结果表明,当有机紫外吸收剂以阴离子的形式进入水滑石层间后,仍有良好的紫外吸收性能并在可见光区有很好的透光性;通过测定插层水滑石的氧化催化活性,与纯有机物相比,Zn2Al-LDH/PBSA和Zn2Al-LDH/DABA的氧化催化活性明显降低。合成的新型的插层水滑石有望在防晒产品中得到应用。     

层板剥离水滑石的制备及影响因素

采用阴离子表面活性剂N-月桂酰基谷氨酸(LG)为插层分子，研究了烷烃-LG-水(O/W)微乳液中烷烃量的变化对插层水滑石层间距的影响，同时研究了烷烃分子大小和水滑石层板阳离子不同对水滑石剥离难易程度的影响。实验表明，随着微乳液中烷烃含量的增加，制备得到了由插层到层板剥离的水滑石，并且烷烃的链长越长，水滑石的剥离越容易实现。层板化学组成对剥离难易程度也有影响，难易程度依次是Mg/Al-LDH，Zn/Al-LDH和Ni/Al-LDH。     

Zn/Al层状双氢氧化物-聚氯乙烯纳米复合物的制备与性能

用共沉淀法制备油酸钾改性的Zn2+、Al 3+层状双氢氧化物(Zn/Al-LDH),以环己酮为溶剂,用溶液插层法制备了Zn/Al层状双氢氧化物-聚氯乙烯(PVC)纳米复合物。采用傅里叶红外(FT-IR)、X-射线衍射(XRD)、透射电镜(TEM)对复合材料的结构及形貌进行了表征,并用热分析仪、万能试验机和紫外分光光度计研究了复合物的热稳定性能、拉伸性能和紫外吸收性能。结果表明:Zn/Al-LDH纳米片层无序分散在PVC基体中;Zn/Al-LDH对PVC低温时的骨干脱氯化氢有促进作用;与PVC膜相比,复合膜的分解温度降低,高温碳化温度升高,复合膜的拉伸强度及断裂伸长率得到提高,在300~380nm具有一定的紫外吸收性能。     

有机紫外吸收剂插层锌铝水滑石的制备及表征

采用离子交换法，以去离子水或乙二醇为分散介质，制备了层间为磺基水杨酸、4-羟基-3-甲氧基肉桂酸和2-羟基-4-甲氧基二苯甲酮-5-磺酸等紫外吸收剂阴离子插层的锌铝水滑石。利用XRD、IR、TG-DTA等技术对样品结构进行表征，采用UV-Vis吸收光谱研究产物的光化学特性，并用Gaussian-98软件包中ab initio分子轨道法(HF/6-31G)计算了3种有机紫外吸收剂的分子结构和电荷分布，提出了合理的客体分子在主体层间的排列方式，分析了其结构与光化学行为的关系。研究表明，由于有机紫外吸收剂进入层间，不仅客体与主体层板存在静电力和氢键相互作用，而且在限域空间中有利于客体之间的相互作用，从而使插层产物的紫外吸收范围和能力显著增强，是一类具有潜在应用价值的无机-有机超分子复合结构的紫外吸收材料。     

酸性橙插层锌铝水滑石的组装及其结构与性能

采用共沉淀法合成酸性橙阴离子插层锌铝水滑石(Zn/Al-AO7 LDHs),研究不同pH值及原料金属离子配比对产物结构的影响,利用X射线粉末衍射(XRD),热分析(TG-DTA),傅里叶变换红外(FT-IR)等表征手段,对插层产物的结构进行表征,确定了制备酸性橙插层锌铝水滑石的最适宜条件.用量子化学的B3PW91/6-31G(d,p)方法对Zn/Al-AO7 LDHs模型分子的空间几何构型进行了优化,通过结构组合得到的层间距为2.33 nm,接近XRD测试得到的层间距,从而说明了酸性橙离子在水滑石层板间的排列方式.进一步以甲酰胺为溶剂对水滑石层板进行剥离,得到澄清溶液,根据剥离产物的XRD谱可以确定剥离实验成功.     

2-羟基-4-甲氧基二苯甲酮-5-磺酸插层水滑石的制备及性能(英文)

以层状镁铝双金属氢氧化物(MgAlLayeredDoubleHydroxides,Mg-AlLDHs)为主体,以有机紫外光稳定剂2-羟基-4-甲氧基二苯甲酮-5-磺酸(BP)为客体,结合焙烧复原法和阴离子交换法合成了具有超分子结构有机-无机插层复合物(MgAl-BPLDHs),研究了层间阴离子、反应介质、pH值、反应时间等因素对于插层材料超分子结构的影响。用FTIR、XRD、TG-DTA、UV-Vis和粒度分析对其不同尺度的结构、热稳定性和紫外光稳定性等进行表征。结果表明,采用阴离子交换法难以进行插层反应;通过焙烧复原法可显著降低MgAl-LDHs层间CO2-离子,从而有利于BP阴离子交换进入MgAl-LDHs层间,在去离子水中,水温100℃,pH=7,反应时间为48h,BP过饱和的条件下合成得到最高插层率的MgAl-BP-LDHs;主体水滑石层板与客体以静电力和氢键相互作用,得到的超分子结构材料具有良好的热稳定及兼具优异的紫外屏蔽、吸收性能,是一种新型的有机-无机复合光热稳定剂。     

超分子结构水杨酸根插层水滑石的组装及结构与性能研究

以锌铝水滑石ZnAl-CO3 LDHs为前体（主体），以乙二醇为分散介质，用离子 交换法组装了水杨酸根（客体）插层水滑石ZnAl-[o-HO(C6H4)COO]LDHs，并用XRD ，FT-IR，TG-DTA等手段对样品进行了表征。结果表明，能过控制离子交换条件， 水杨酸根阴离子可取代锌铝水滑石前体层间的CO3^2-离子，组装得到晶体结构良好 的水杨酸根插层水滑石。通过研究发现，主体水滑石层板与客体以静电力和氢键相 互作用，得到的超分子结构材料紫外阻隔作用增强并具有较好的稳定性，从而成为 一种集屏蔽和吸收双重功能的新型无机-有机得合紫外阻隔材料。     

铈杂多配离子-水滑石超分子层柱材料ZnAl-Ce(PMoV)2的插层组装、表征及催化性能

以十四酸根阴离子柱撑Zn-Al水滑石Zn0.77Al0.22(OH)2.0.22C13H27COO.0.81 H2O(记为ZnAl-14A)为预撑前体,在水溶液中用离子交换法将以2∶17缺位杂多酸根离子(P2Mo16VO61)11-记为(P Mo V)为配体的稀土杂多配阴离子Ce(P2Mo16VO61)219-(记为Ce(PMoV)2)插层组装到水滑石层板间,合成了一种具有大的层间距(3.37 nm)的超分子插层材料Zn0.77Al0.23(OH)2.0.0105[Ce(P1.9Mo15.7V1.1O61)2].0.011C13H27COO.0.83H2O(记为ZnAl-Ce(PMoV)2)。用ICP,IR,XRD和DTA对产物的组成和结构进行了表征。结果表明,该产物中Ce(PMoV)2配阴离子沿其长轴垂直于层板的方向分布于水滑石层间;产物具有规整的层状结构和热稳定性;产物对乙酸与正丁醇的酯化反应,二甘醇的脱水-环化反应和H2O2氧化环己烷的反应有良好的催化性能,且易于回收重复使用。     

CuZnAl类水滑石衍生复合氧化物催化环己醇脱氢反应的研究

采用共沉淀法合成了不同CuZnAl配比的类水滑石,通过不同温度焙烧制备其衍生复合氧化物.采用X-射线衍射(XRD)、差热热重(TG-DTA)、N2吸附-脱附和CO2程序升温脱附法(CO2-TPD)对类水滑石和衍生复合氧化物进行了表征.将所得复合氧化物用于环己醇脱氢制备环己酮的反应中考察其催化活性.实验结果表明:CuZnAl类水滑石衍生复合氧化物对该反应具有很高的催化活性,在反应温度220℃时以CuZnAl[n(Cu)/n(Zn)/n(Al)=1.34/0.66/1.0]类水滑石为前躯体,400℃焙烧所得的衍生复合氧化物表现出最佳的催化活性,环己醇转化率高达94.9%,环己酮的选择性近100%.     

IR/UV and UV/UV double-resonance study of guaiacol and eugenol dimers

Guaiacol (2-methoxyphenol) and eugenol (4-allyl-2-methoxyphenol) molecules are biologically active phenol derivatives with an intramolecular -OH...OCH3 hydrogen bond (H bond). Pulsed supersonic expansions of mixtures of either of the two molecules with He yield weakly bound homodimers as well as other higher-order complexes. A number of complementary and powerful laser spectroscopic techniques, including UV-UV and IR-UV double resonances, have been employed to interrogate the species formed in the expansion in order to get information on their structures and spectroscopic properties. The interpretation of the spectra of eugenol dimer is complex and required a previous investigation on a similar but simpler molecule both to gain insight into the possible structures and support the conclusions. Guaiacol (2-methoxyphenol) has been used for that purpose. The combination of the broad laser study combined with ab initio calculations at the Becke 3 Lee-Yang-Parr/6-31+Gd level has provided the isomer structures, the potential-energy wells, and shed light on the inter- and intramolecular interactions involved. Guaiacol homodimer has been shown to have a single isomer whereas eugenol dimer has at least two. The comparison between the computed geometries of the dimers, their respective energies, and the vibrational normal modes permits the identification of the spectra.     

紫外光固化设备与光固化合物的研究

涂层紫外光固化技术由于在能源节省、产品质量以及环保方面的优势,正在不断的迅速发展.本文综述了近年来辐照设备的进步,以及紫外光固化体系所涉及的单体、齐聚体和光引发剂的研究发展情况.     

Rapid estimation of global sugars by UV photodegradation and UV spectrophotometry

The UV/UV method developed for the measurement of specific wastewater pollution parameters (ammonium, Kjeldahl nitrogen, total phosphorus) is adapted to the determination of sugars in fruit juices and soft drinks. The procedure is based on the UV spectrophotometric detection of by-products of UV photodegradation of carbohydrates. Time of analysis is greatly reduced by using specific pH conditions and diluted samples.     

Effect of UV light scattering during photopolymerization on UV spectroscopy measurements

A photopolymerization reaction involving 2-hydroxyethylmethacrylate (HEMA), a hydroxytelechelic polybutadiene (HTPB) and 2,2-dimethyl-2-hydroxyacetophenone (Darocur 1173) as photoinitiator has been investigated by Real Time UV and Real Time IR spectroscopies. For this system, RTUV analyses are completely opposite to the expected curves, namely a decrease in the sample absorbance (photobleaching phenomenon). This apparent contradiction has been explained by a scattering phenomenon inside the sample, which can be linked to the formation of sub-structures that can create local fluctuations of refractive index during the polymerization. A four-flux theory, which takes into account the polymer absorption and scattering properties, has allowed us to describe the UV light intensity variation inside the sample.     

Photostability of Cosmetic UV Filters on Mammalian Skin Under UV Exposure

Previous studies showed that the common UV filter substances benzophenone‐3 (BP–3), butyl methoxydibenzoylmethane (BM–DBM), octocrylene (OCR), ethylhexyl methoxycinnamate (EHMC), ethylhexyl salicylate (EHS) and ethylhexyl triazone (EHT) were able to react with amino side chains of different proteins in vitro. To transfer the results to mammalian skin conditions, sunscreen products were applied on both prepared fresh porcine skin and glass plates, followed by UV irradiation and the determination of depletion of the respective UV filters. Significantly lower recoveries of the UV filters extracted from skin samples than from glass plates indicated the additional reaction of the UV filters with skin constituents, when proteins will be the most important reactants. Among the products tested, BP‐3 showed the greatest differences in recoveries between glass and skin samples of about 13% and 24% after 2 and 4 h of irradiation, respectively, followed by EHS > BM‐DBM > OCR > EHMC > EHT. The obtained results raise the question, whether the common in vitro evaluations of sunscreens, using inert substrate materials like roughened quartz or polymethyl methacrylate (PMMA) plates are really suitable to fully replace in vivo methods, as they cannot include skin‐typical reactions.     

UV spectra of N-vinylpyrroles

Chemistry of Heterocyclic Compounds - The effect of the structure and the medium on the position and intensity of the absorption bands in the UV spectra that attest to the presence of a single...     

UV doses worldwide

UV radiation affects human health. Human exposure to UV radiation causes a few beneficial health effects like vitamin D3 formation but it causes many detrimental health effects: sunburn, ocular damage, photoaging, immune suppression, DNA damage and skin cancer. In countries with fair-skinned populations, skin cancer is the most diagnosed of all cancers. In the United States in 2002, there were over one million new skin cancer cases. That means one out of every 285 people got skin cancer. Skin cancer of fair-skinned individuals is increasing at an alarming rate (4-6% per year) around the world and has now reached so-called "pandemic" proportions. Thus, it is important to know what UV doses people around the world get throughout their lives. This review covers how the outdoor UV doses are weighted for different biological effects, the most commonly used measuring devices for terrestrial and personal UV doses, the natural and other effects on terrestrial and personal UV doses, the time people spend outside, their ambient exposures and the terrestrial and personal UV doses of adult outdoor and indoor workers as well as children and adolescents around the world. Overall, outdoor-working adults get about 10%, while indoor-working adults and children get about 3% (2-4%) of the total available annual UV (on a horizontal plane). People's UV doses increase with increasing altitude and decreasing latitude; most indoor-working adult Europeans get 10,000-20,000 J/m2 per year, Americans get 20,000-30,000 J/m2 per year and Australians are estimated to get 20,000-50,000 J/m2 per year (excluding vacation, which can increase the dose by 30% or more).     

UV Signature Mutations

Sequencing complete tumor genomes and exomes has sparked the cancer field's interest in mutation signatures for identifying the tumor's carcinogen. This review and meta‐analysis discusses signatures and their proper use. We first distinguish between a mutagen's canonical mutations—deviations from a random distribution of base changes to create a pattern typical of that mutagen—and the subset of signature mutations, which are unique to that mutagen and permit inference backward from mutations to mutagen. To verify UV signature mutations, we assembled literature datasets on cells exposed to UVC, UVB, UVA, or solar simulator light (SSL) and tested canonical UV mutation features as criteria for clustering datasets. A confirmed UV signature was: ≥60% of mutations are C→T at a dipyrimidine site, with ≥5% CC→TT. Other canonical features such as a bias for mutations on the nontranscribed strand or at the 3′ pyrimidine had limited application. The most robust classifier combined these features with criteria for the rarity of non‐UV canonical mutations. In addition, several signatures proposed for specific UV wavelengths were limited to specific genes or species; UV's nonsignature mutations may cause melanoma BRAF mutations; and the mutagen for sunlight‐related skin neoplasms may vary between continents.     

UV curing behaviors and hydrophilic characteristics of UV curable waterborne hyperbranched aliphatic polyesters

A series of waterborne hyperbranched polyesters (WBHPs) endcapped with methacrylic and salt-like groups in different ratios have been investigated as UV curable resins. The kinetic studies of the drying step and UV curing were carried out by FT-IR measurements. The drying of the film of 100 μm thickness was completed in less than 6 hr at 70°C or within 10 hr at 50°C in an oven. The influence of different photoinitiators and their concentrations, extent of unsaturation and acid content of WBHP on final unsaturation conversion was studied. The surface free energy is a critical character, which affects the surface properties of a cured film. So one method based on the measurement of contact angle of a pure liquid on a solid surface was applied to determine the polar and dispersive components of the surface energy of UV cured films. The investigations of surface energy of WBHPs illustrated that those with more acid content and thus higher polar component are more sensitive to water, while those containing less acid content and thus lower polar term are less water sensitive. Moreover, the UV cured films of WBHPs and their blends with commercial waterborne resins (trade name EB 210, EB 2002, EB 11 and IRR 160) have acceptable pendulum hardness varying from 55 to 180 sec. Copyright © 2003 John Wiley & Sons, Ltd.