Effect of comonomer sorption on radiation-induced copolymer grafting onto polyethylene and EVA films in the vapor phase

Radiation-induced copolymer grafting of acenaphthylene and maleic anhydride onto polyethylene or EVA film in the vapor phase was carried out and the effect of comonomer sorption on the grafting was studied. When polyethylene film was used as a backbone polymer, the sorption of the binary monomers during the grafting increased linearly as the grafting reaction proceeded. The marked increase was probably caused by the formation of a grafted layer. Particularly, the sorption of maleic anhydride was brought about by the existence of a grafted layer. In grafting onto EVA film, the content of maleic anhddride in the grafted copolymer increased with the increasing content of vinyl acetate in EVA. Continuous measurements of sorption of the comonomers onto EVA and grafted EVA films were carried out by use of an electrobalance. The distinctive feature of the sorption was that the equilibrium sorption of acenaphthylene or maleic anhydride onto the grafted EVA film increased and the diffusion constants for both comonomers decreased markedly with increasing percentage of graft. The copolymer grafting was explained from these results by assuming that the monomer molecules are supplied to the propagating chain ends mostly through a sorbed state on the polymer film.     

Radiation-induced solid-state copolymerization of maleic anhydride and acenaphthylene

Radiation-induced solid-state copolymerization of the maleic anhydride–acenaphthylene system was carried out for the purpose of studying the solid-state polymerization of vinyl compounds in a binary system. Melting point measurement confirmed that this binary monomer system forms a eutectic mixture in the solid state. The solid-state polymerization of these monomers proceeds at maximum rate at the eutectic composition, and the polymerization products consist of a mixture of polyacenaphthylene and 1:1 maleic anhydride–acenaphthylene alternating copolymer. Since the 1:1 copolymer was obtained in solution polymerization also and maleic anhydride did not homopolymerize in solid state, it is considered that the solid-state copolymerization of maleic anhydride and acenaphthylene occurs in a liquidlike state at the boundary of the two monomer crystals.     

γ- and ultraviolet-radiation-induced solid-state polymerization of maleimide in a few binary systems

The solid-state polymerization of maleimide by γ- and ultraviolet irradiation was carried out in binary systems with succinimide, maleic anhydride, and acenaphthylene. Polymaleimide obtained from the solid-state polymerization of maleimide by γ-rays was amorphous, while that obtained from the solid-state polymerization by ultraviolet rays was highly crystalline. In the maleimide–succinimide system the rate of polymerization reached a maximum nearly at the eutectic composition when the polymerization was carried out by γ-irradiation. With ultraviolet irradiation the rate of polymerization became higher with increasing content of succinimide in the feed. In the maleimide–maleic anhydride system a copolymer of both constituents was formed by γ-irradiation, but almost no homopolymer was produced. On the other hand, two kinds of polymers, a crystalline copolymer and an amorphous one, were produced by ultraviolet irradiation. The results were compared with those obtained from the copolymerization in solution. In the maleimide-acenaphthylene system the main products with ultraviolet irradiation was the dimer of acenaphthylene.     

Radiation grafting from binary monomer mixtures. I. Vinyl ether of monoethanolamine and vinyl ether of ethyleneglycol

Gamma-radiation grafting of vinyl ether of monoethanolamine and vinyl ether of ethyleneglycol (VEEG) on polyethylene films has been studied from binary monomer mixtures. The effect of co-monomer composition and total exposure radiation dose on the grafting process is investigated. A combination of potentiometric and gravimetric techniques is applied to determine the grafting degree of each monomer in the final graft copolymer. The presence of more active monomer VEEG in the mixture was found to enhance the grafting of both monomers because the increasing of copolymerization rate which in turn increases the total grafting degree. The modification of the hydrophilic properties of the graft copolymer is studied by examining the grafted films for water- and copper (II) ions uptake.     

γ-ray and ultraviolet graft copolymerization of maleimide by vapor-phase method

Graft copolymerization of maleimide onto ethyl cellulose and polyethylene films by using its sublimation vapor was carried out under γ- or ultraviolet irradiation. When polyethylene film was used as a backbone polymer the grafting reaction proceeded without a perceptible sorption of monomer, while a considerable amount of monomer was captured into ethyl cellulose film and grafting of the sorbed monomer was observed. The monomer seemed to be monomolecularly dispersed in this film. The presence of air retarded the reaction. The grafted films were characterized by strong infrared absorption bands due to polymaleimide branching. The fractions assigned to the graft copolymer were isolated from the grafted films by selective elution. The grafted branches were supposed to be very short, judging from the polymaleimide contents of those fractions.     

二元单体在棉纤维上的γ辐射接枝

在氮气气氛下用γ射线辐照的方法在棉纤维上接枝苯乙烯/马来酸酐、苯乙烯/甲基丙烯酸二甲胺乙酯、苯乙烯/醋酸乙烯酯二元单体. 研究了溶液中单体的浓度和二元单体的摩尔比等条件对接枝率的影响, 并探讨了两种单体的竞聚率对接枝率、接枝膜的组成及性能的影响. 结果表明决定二元接枝生成物结构比例的是二元单体的比例及其竞聚率. 接枝产物的红外、热重分析进一步佐证了竞聚率对不同二元单体体系接枝生成物结构的影响. X射线衍射结果表明棉纤维素上接枝不同的二元单体后均引起结晶度的下降, 而且结晶度随接枝率的增加而降低, 证明二元接枝反应是从纤维素无定型区通过第三相向结晶区逐步扩展的.     

Polymers from renewable resources. II. A study in the radio chemical grafting of poly(styrene‐alt‐maleic anhydride) onto cellulose extracted from pine needles

A binary mixture of styrene and maleic anhydride has been graft copolymerized onto cellulose extracted from Pinus roxburghii needles. The reaction was initiated with gamma rays in air by the simultaneous irradiation method. Graft copolymerization was studied under optimum conditions of total dose of radiation, amount of water, and molar concentration previously worked out for grafting styrene onto cellulose. Percentage of total conversion (Pg), grafting efficiency (%), percentage of grafting (Pg), and rates of polymerization (R_p), grafting (R_g), and homopolymerization (R_h) have been determined as a function of maleic anhydride concentration. The high degree of kinetic regularity and the linear dependence of the rate of polymerization on maleic anhydride concentration, along with the low and nearly constant rate of homopolymerization suggest that the monomers first form a complexomer which then polymerizes to form grafted chains with an alternating sequence. Grafting parameters and reaction rates achieve maximum values when the molar ratio of styrene to maleic anhydride is 1 : 1. Further evidence for the alternating monomer sequence is obtained from quantitatively evaluating the composition of the grafted chains from the FT‐IR spectra, in which the ratio of anhydride absorbance to aromatic (CC) absorbance for the stretching bands assigned to the grafted monomers remained constant and independent of the feed ratio of maleic anhydride to styrene. Thermal behaviour of the graft copolymers revealed that all graft copolymers exhibit single stage decomposition with characteristic transitions at 161–165°C and 290–300°C. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1763–1769, 1999     

Dual monomer grafting of styrene and maleic anhydride onto model hydrocarbon substrates

Styrene and maleic anhydride (MAn) were successfully grafted, alone and simultaneously, onto various model hydrocarbon substrates at 180 °C with 2,5‐dimethyl‐2,5‐di‐(t‐butyl peroxy)hexane (L101) as a free‐radical initiator. Dodecane, 1‐dodecene, and 2,6,10,14‐tetramethylpentadecane were selected as model compounds to investigate the effects of terminal unsaturation and branching on grafting and crosslinking. These compounds were chosen to mimic the aforementioned microstructural characteristics that are commonly observed in polyethylene. The results demonstrate that terminal unsaturation increases the amount of crosslinked material in the presence of L101. With respect to grafting, for the single monomer systems, MAn prefers to graft as single saturated units, whereas styrene prefers to graft as long chains of polystyrene oligomers. However, when both monomers are grafted simultaneously, graft yields are drastically reduced because of a propensity for the two monomers to form a styrene–maleic anhydride copolymer. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2456–2468, 2000     

Synthesis and characterization of 4‐vinyl pyridine‐grafted Teflon‐PFA film for water technologies

To get highly reactive polymeric materials for selective studies of enzyme immobilization, water purification, separation, and enrichment technologies, we attempted to graft 4‐vinyl pyridine (4‐VP) onto Teflon‐PFA by simultaneous γ‐ray initiation. The resulting graft copolymers were quaternized by treatment with some alkylating agents. Optimum conditions for grafting were evaluated through the variation of the total dose of radiation, the amount of water, and the monomer concentration. The effect of the solvent composition (H₂O/MeOH) was also studied. In the presence of MeOH, grafting occurred less often and was nonselective as 4‐VP was incorporated on both sides in comparison with highly selective grafting in an aqueous medium. The percentages of the grafting, total conversion, and grafting efficiency and the rates of the polymerization, grafting, and homopolymerization were also evaluated. Some other monomers such as methacrylic acid, methyl methacrylate, maleic acid, acrylonitrile, and vinyl imidazole were not incorporated onto the backbone film under the optimum grafting reaction conditions evaluated for the grafting of 4‐VP. Although some grafting occurred, the graft yield was too low to be considered of any significance. The grafted films were quaternized with benzyl chloride, and quaternized and unquaternized films were used for the immobilization of lipase. The former showed high activity with lipase and has potential for development as a bioreactor. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4506–4518, 2000     

Grafting copolymerization of styrene and maleic anhydride binary monomer systems induced by UV irradiation

Photografting copolymerization of maleic anhydride (MAH) and styrene (St) onto LDPE film was investigated by using a one-step method, and further thermally induced grafting copolymerization of them was carried out by using a two-step method. Regarding the photografting copolymerization of MAH/St binary monomer system, both conversion percentage (CP) and grafting efficiency (GE) increased with raising the content of MAH in the monomer feed. In addition, the content of MAH in the grafted copolymers also increased with increasing the fraction of MAH in the monomer feed. The formation of LDPE-g-P(MAH-co-St) grafted film was identified by FTIR and ESCA spectroscopy. In the case of grafting copolymerization of MAH/St by the two-step method, grafting copolymerization proceeded slowly compared with the non-grafting copolymerization. The apparent activation energy (E_a) for the non-grafting copolymerization in the solution and the grafting copolymerization on LDPE film was 24 and 82 kJ/mol, respectively, which were noticeably lower than those of MAH/vinyl acetate (MAH/VAC) binary monomer system under the similar grafting conditions. These data of E_a explained why the grafting copolymerization of styrene/MAH took place faster than that of MAH/VAC binary monomer system. The composition of the grafted copolymer chains was largely affected by the composition of the monomer feeds; however, the composition of the non-grafted copolymers nearly remained at 1/1 even in systems with largely different MAH/styrene ratios in monomer feeds. It is indicated that the non-grafting copolymerization proceeded predominantly following alternating copolymerization, but the grafting copolymerization performed random copolymerization.     

Biodegradability of poly(3-hydroxybutyrate) film grafted with vinyl acetate: Effect of grafting and saponification

Radiation-induced graft polymerization of vinyl acetate (VAc) onto poly(3-hydroxybutyrate) (PHB) film was carried out. At a degree of grafting higher than 5%, the grafted films (PHB-g-VAc) completely lost the enzymatic degradability that is characteristic of PHB due to the grafted VAc covering the surface of the PHB film. However, the biodegradability of the PHB-g-VAc films was recovered when the films were saponified in alkali solution under optimum conditions. Graft chains of the PHB-g-VAc film reacted selectively to become biodegradable polyvinyl alcohol (PVA). The biodegradability of the saponified PHB-g-VAc film increased rapidly with time.     

苯乙烯/马来酸酐和苯乙烯/甲基丙烯酸二甲氨基乙酯二元体系在聚四氟乙烯多孔膜上的γ辐射接枝

在氮气的氛围下用γ辐照的方法在聚四氟乙烯多孔膜上接枝苯乙烯 马来酸酐、苯乙烯 甲基丙烯酸二甲氨基乙酯二元单体 .并且研究了剂量、剂量率、溶液中单体的浓度和二元单体的摩尔比等条件对接枝率的影响 .探讨了两种单体的竞聚率对接枝率、接枝膜的组成及性能的影响 .结果表明 ,苯乙烯 马来酸酐二元体系对接枝率有协同效应 ,苯乙烯 甲基丙烯酸二甲氨基乙脂二元体系对接枝率表现为加合效应 .制备的二元接枝的聚四氟乙烯多孔膜可以进一步磺化来制备用于质子交换膜燃料电池的质子交换膜 .     

Monomer reactivity ratios in graft copolymerization

This paper discusses monomer reactivity ratios in various radiation- and redox-initiated graft copolymerizations. The polymers studied were polyethylene, cellulose acetate, poly(vinyl chloride), polytetrafluoroethylene, poly(vinyl alcohol), and poly(methyl methacrylate); the comonomer mixtures were styrene–acrylonitrile, methyl acrylate–styrene, acrylonitrile–methyl acrylate, and vinyl acetate–acrylonitrile. The polymer–comonomer mixture systems were so chosen as to permit study of both homogeneous and heterogeneous systems. The homogeneous systems included systems of low and high viscosity. The heterogeneous systems included both polymers swollen by the comonomer mixture and polymers not swollen by the comonomer mixture. None of the homogeneous grafting systems studied showed deviations from the normal copolymerization behavior under a variety of experimental conditions. Monomer reactivity ratios in graft copolymerization were the same as the values in nongraft copolymerization. The heterogeneous systems in which the polymer was swollen by the comonomer mixture yielded grafted copolymer compositions which were the same as those in nongraft copolymerization. The heterogeneous grafting system polytetrafluoroethylene/styrene–acrylonitrile showed deviations from normal copolymerization behavior at low degrees of grafting when the reaction was only on the polymer surface. The behavior became normal at higher degrees of grafting when the system approaches that in which the polymer is swollen by the comonomers. In all reaction systems, it was found that the use of radiation to initiate the reaction does not in any way affect the copolymerization behavior of the two monomers in a comonomer pair.     

固相共聚接枝合成功能化聚丙烯及机理研究

通过马来酸酐 (MAH)和乙酸乙烯酯 (VAc)固相共聚接枝聚丙烯 (PP) ,在二者的投料摩尔比接近 1:1时 ,得到了高接枝率的多官能团功能化的PP .反应的机理是两单体摩尔比接近 1:1时容易形成较为稳定的过渡态 ,从而两者的共聚活性大大增加 ,接枝率大大提高 ,同时抑制了接枝产品熔体流动指数的增加 .这种含有多种官能团 (酸酐官能团和酯基官能团 )的极性PP对于拓展PP的应用范围 ,促进PP本身及其共混合金材料的功能化和高性能化有着重要的意义     

Grafting of methyl methacrylate and its derivatives onto blood

The grafting of vinyl monomers by tri-n-butylborane to blood has been investigated. The infrared spectra indicated that the monomers were grafted onto blood components. The grafting seems to occur onto blood proteins, mainly onto hemoglobin. The presence of water was essential to the grafting. The hydrolysis of the graft suggests that basic amino acids in the blood proteins, such as lysine and histidine, play an important role in the grafting.     

Synthesis and characterization of anionic graft copolymers containing poly(ethylene oxide) grafts

Anionic graft copolymers were synthesized through grafting of poly(ethylene glycol) monomethyl ether (MPEG) onto terpolymers containing succicinic anhydride groups. The backbone polymers were prepared through radical terpolymerization of maleic anhydride, styrene, and one of the following monomers: methyl methacrylate, ethylhexyl methacrylate, and diethyl fumarate. MPEG of different molecular weights were grafted onto the backbone through reactions with the cyclic anhydride groups. In this reaction one carboxylic acid group is formed together with each ester bond. The molecular weights of MPEG were found to influence the rate of the grafting reaction and the final degree of conversion. The graft copolymers were characterized by IR, GPC, and ¹H-NMR. Thermal properties were examined by DSC. Graft copolymers containing 50% w/w of MPEG 2000 grafts were found to be almost completely amorphous, presumably because of crosslinking, and hydrogen bonding between carboxylic acid groups in the backbone and the ether oxygens in MPEG grafts. © 1995 John Wiley & Sons, Inc.     

Synthesis and characterization of anhydride-functional polycaprolactone

Polycaprolactone-graft-maleic anhydride (PCL-g-MA) copolymer was prepared by grafting maleic anhydride onto PCL in a batch mixer and in an extruder using dicumyl peroxide as the initiator. The graft content was determined with the volumetric method by converting the anhydride functions to acid groups and then titrating with ethanolic potassium hydroxide. The grafted polymer was extracted with xylene to remove any unreacted monomer before the estimation step. The effect of temperature and the various concentrations of the initiator and monomer used for the grafting reaction were investigated. The presence of residual initiator in the reaction product was checked using thin-layer chromatography. Molecular weight determination was carried out for the pure and grafted polymer using gel permeation chromatography to determine if chain scission was present. Results indicate that maleic anhydride is grafted onto PCL using free radical initiators. The grafting reaction was confirmed by FTIR and NMR techniques. FTIR spectra showed absorption bands around 1785 and 1858 cm⁻¹. NMR spectra gave signals for methine proton at 3.47 ppm. For a given peroxide level, a higher temperature or residence (reaction) time gave higher percentage of grafted MA. There was an optimum temperature and initiator concentration after which the percentage of MA grafted on PCL decreased. The number-average molecular weight, tensile strength, and the percent elongation of PCL-g-MA were comparable to those of PCL before grafting. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1139–1148, 1997     

Surface‐confined photopolymerization of single‐ and mixed‐monomer systems to tailor the wettability of poly(L‐lactide) film

The major objective of this research was to modify the surface characteristics of poly(L ‐lactide) (PLA) by grafting a combination of hydrophilic polymers to produce a continuum of hydrophilicity. The PLA film was solvent cast, and the film surfaces were activated by ultra violet (UV) irradiation. A single monomer or combination of two monomers, selected from vinyl acetate (VAc), acrylic acid (AA), and acrylamide (AAm), were then grafted to the PLA film surface using a UV induced photopolymerization process. The film surfaces resulting from each reaction step were analyzed using ATR‐FTIR spectroscopy and contact angle goniometry. Results showed that AAm dominated the hydrophilicity of the film surface when copolymerized with VAc or AA, while the water contact angles for PLA films grafted with poly(vinyl acetate‐co‐acrylic acid) varied more gradually with feed composition. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6534‐6543, 2006     

不同引发剂引发SBS接枝马来酸酐的机理研究

采用FTIR和1 H NMR研究了引发剂过氧化二苯甲酰 (BPO)和偶氮二异丁腈 (AIBN)对聚苯乙烯 聚丁二烯 聚苯乙烯 (SBS)接枝马来酸酐 (MAH)的影响 ,讨论了相应的接枝机理 ,通过丁二烯 (PB)段碳碳双键(CC)随接枝率变化的规律进一步验证了机理 .结果表明 ,BPO与AIBN引发接枝的机理不同 ,BPO可引发PB的双键和烯丙位碳氢键 ,但引发烯丙位的速率比引发双键大 ;当BPO浓度达到一定量时 ,大量烯丙位的引发保护了碳碳双键 ,随BPO浓度的增大 ,碳碳双键的含量先减少后增加 .AIBN不能引发PB段烯丙位的碳氢键 ,只能引发双键接枝     

Synthesis and characterization of radiation grafted films for removal of arsenic and some heavy metals from contaminated water

Grafting of styrene/maleic anhydride and methyl methacrylate/maleic anhydride binary monomers onto the low density polyethylene film was performed using the γ-ray irradiation technique. Then, the synthesized grafted films were treated with different ammonia derivatives for developing chelating functionalization. These chelating products were characterized by the gravimetric method as well as by the Fourier transformed infrared spectroscopic method, and were used for removal of arsenic and some heavy metals from aqueous solutions. The optimum absorbed dose of 30 kGy reveals the graft yielding of about 325% in the films. Uptake of arsenic and some heavy-metal ions (Cr(III), Mn(II), Fe(III), Ni(II), Cu(II) and Pb(II)) from contaminated water by the chelating functionalized films (CFF) was examined by an atomic absorption spectrophotometer. The maximum arsenic removal capacity of 5062 mg/kg has been observed for the film treated with hydroxylamine hydrochloride. The CFF prepared by semicarbazide and thiol analogs show affinity toward the metal ions with an order: Cu(II)>Fe(III)>Mn(II) etc. The results obtained from this study indicate that the functionalized films show good chelating and ion-exchange property for metal ions.