光敏共聚物P(St/VM-co-MA)自组装胶体粒子及其性能

以苯乙烯类光敏单体7-(4-乙烯基苄氧基)-4-甲基香豆素(VM)、苯乙烯(St)、马来酸酐(MA)为共聚单体,采用自由基聚合法制备了光敏性双亲共聚物P(St/VM-co-MA).在选择性溶剂(N,N-二甲基甲酰胺(DMF)/H2O)中对P(St/VM-co-MA)进行自组装,用透射电镜(TEM)和动态激光光散射(DLS)表征了自组装胶体粒子的形态、粒径大小及其分布.利用紫外光照使胶体粒子中香豆素基元发生光二聚反应,形成交联胶体粒子,并用紫外-可见光分光光度计(UV-Vis)跟踪其交联过程.用DLS研究了交联和未经交联胶体粒子的粒径和结构稳定性,用激光扫描共聚焦显微镜(LSCM)和光学显微镜考察了胶体粒子的乳化、包覆性能.结果表明:交联和未经交联胶体粒子均具有乳化性,且在乳化过程中可实现对油溶性染料的包覆.胶体粒子交联后,粒径有所减小,结构稳定性、乳化性能、包覆性能均有所提高.     

共溶剂性质对双亲性无规共聚物P(St-co-DM)胶束化行为及其性能的影响

以苯乙烯(St)和甲基丙烯酸二甲氨乙酯(DMAEMA)为共聚单体, 通过普通自由基溶液聚合合成了双亲性无规共聚物P(St-co-DM). 用傅里叶变换红外(FTIR)光谱、核磁共振氢谱(¹H NMR)、凝胶渗透色谱(GPC)和差示扫描量热(DSC)仪对聚合物结构进行表征. 研究了共溶剂的性质对P(St-co-DM)自组装胶束结构及其乳化性能的影响. 用透射电镜(TEM)和动态激光光散射(DLS)表征了自组装胶体粒子的形态、粒径大小及其分布. 通过测量胶束在甲苯/水界面的接触角表征胶束表面性能. 结果表明: P(St-co-DM)以四氢呋喃(THF)为共溶剂自组装时, 胶束的临界聚集水含量较大, 胶束表面亲水性较强, 流体力学半径较大; 用二氧六环或THF为共溶剂, 水为选择性溶剂, P(St-co-DM)自组装可以得到外层松散、内层比较密实的球状胶束, 用N,N-二甲基甲酰胺(DMF)为共溶剂时, 胶束整体呈现比较密实的球状胶束; 分别用DMF、二氧六环和THF为共溶剂制备的胶束, 其接触角均值都小于90°, 可形成O/W型(水包油型)乳液. 乳化实验结果表明, 以二氧六环和THF为共溶剂制备的胶束作为颗粒乳化剂制备的乳液性能较好.     

双亲性无规共聚物P（VM-co-AMPS）的自组装及其性能

以2-丙烯酰胺基-2-甲基丙磺酸（AMPS）和苯乙烯类光敏单体7-（4-乙烯基苄氧基）-4-甲基香豆素（VM）为共聚单体,采用自由基聚合法制备了光敏性双亲共聚物P（VM-co-AMPS）。P（VM-co-AMPS）在溶剂水中自组装胶束化,用原子力显微镜（AFM）表征了自组装胶体粒子的形态、粒径及其分布。紫外光照使胶体粒子中香豆素基元发生光二聚反应,用紫外-可见光分光光度计（UV-Vis）跟踪其光二聚交联过程,用光学显微镜考察了胶体粒子的乳化性能。结果表明：胶体粒子具有较好的紫外吸收性能和较好的乳化性能。该胶束制备工艺简单,条件温和,避免了溶剂的使用。     

多重敏感性双亲共聚物P(DM-co-AA-co-CA)的自组装及性能

以甲基丙烯酸二甲胺乙酯（DM）、丙烯酸（AA）和香豆素丙烯酸酯化物（CA）为共聚单体,通过普通自由基溶液聚合合成了多重敏感性双亲共聚物P(DM-co-AA-co-CA),用傅里叶变换红外（FTIR）、核磁共振（1H-NMR）、凝胶渗透色谱（GPC）和差示扫描量热仪（DSC）对聚合物结构进行表征．在选择性溶剂四氢呋喃/水中对所得多重敏感性双亲共聚物P(DM-co-AA-co-CA)进行自组装,结果表明,调节组装环境的pH值可以得到荷正电或负电的两性胶束粒子．用紫外可见光分光光度计、荧光分光光度计、Zeta电位测定仪、DLS和TEM研究了多重敏感性双亲共聚物的溶液自组装及其组装体的性能,结果显示,调节pH值可以有效的控制胶束的粒径大小及其LCST,并在pH为8.54时胶束溶液的紫外吸收和荧光发射强度达到最大值,且该胶束溶液在酸碱性较强时具有良好的乳化性能．     

嵌段共聚物OSM1-PCLA-PEG-PCLA-OSM1的合成及其pH和温度敏感性

采用开环聚合法和自由基聚合法合成了生物可降解嵌段共聚物OSM1-PCLA-PEG-PCLA-OSM1, 并对其进行了结构表征. 采用荧光分光光度计和激光粒度仪对共聚物溶液临界胶束浓度(CMC)和粒径大小及分布进行了考察, 研究了温度和pH对共聚物胶束形成的影响. 相转变过程研究结果表明, 共聚物溶液具有pH和温度双重敏感性. 共聚物溶液在一定温度和pH条件下可发生溶液-凝胶相转变.     

探索光敏性共聚物P(St/CS-alt-MA)的自组装及其乳化行为

以苯乙烯(St)、马来酸酐(MA)、香豆素苯乙烯醚化物(CS)为单体, 通过自由基溶液聚合合成了双亲性交替共聚物P(St/CS-alt-MA), 用凝胶渗透色谱、核磁共振等对聚合物结构进行表征, 并对其溶液自组装及组装体的乳化性进行了研究. 结果表明双亲性P(St/CS-alt-MA)可以在选择性溶剂中进行自组装形成马来酸酐单元为亲水微区、CS与苯乙烯单元为疏水微区的胶体粒子, 用紫外分光光度计, XPS, TEM研究了聚合物胶体粒子性质, 结果显示, P(St/CS-alt-MA)在水溶液中可以形成两亲性聚合物胶体粒子, 亲水单元在胶粒表面富集, 该两亲性聚合物胶体粒子具有良好的乳化性能.     

支化型交替聚(苯乙烯-alt-马来酸酐)自组装胶束的制备及其乳化性能

利用支化型交替聚(苯乙烯-alt-马来酸酐)(BPSMA)在选择溶剂DMF-H2O中自组装制备球形胶束,以之作为新型颗粒乳化剂稳定白油-水体系,探讨胶束浓度和pH对BPSMA胶束乳化性能的影响。用紫外分光光度计(UV-Vis)追踪了聚合物溶液自组装过程,粒径及Zeta电位分析仪和透射电子显微镜(TEM)表征了BPSMA胶束的基本性质;利用光学显微镜分析了乳液性质;扫描电子显微镜(SEM)观察了胶束在固化后的油水界面的形貌。结果表明:BPSMA胶束具有优异的乳化效率,在极低的胶束质量浓度下(0.25~1.00mg/mL)亦可长期稳定白油-水乳液;BPSMA胶束所稳定的乳液具有明显的pH响应性,当pH≤6时,胶束呈球形颗粒状吸附并稳定于油水界面,当pH6时,胶束从油水界面脱离,乳液破乳;此外,BPSMA胶束作为颗粒乳化剂还具备良好的普适性,可以长效稳定碳酸二辛脂、辛酸丙基庚酯、硅油、棕榈酸异辛酯和润肤油脂等。     

支化型交替聚(苯乙烯-alt-马来酸酐)自组装胶束的制备及其乳化性能

利用支化型交替聚(苯乙烯-alt-马来酸酐)(BPSMA)在选择性溶剂DMF-H_2O中自组装制备球形胶束,以该胶束作为新型颗粒乳化剂稳定油-水体系,探讨胶束浓度和pH对BPSMA胶束乳化性能的影响。用紫外分光光度计(UV-Vis)追踪了聚合物溶液自组装过程;粒径及Zeta电位分析仪和透射电子显微镜(TEM)表征了BPSMA胶束的基本性质;利用光学显微镜分析了乳液性质,扫描电子显微镜(SEM)观察了胶束在固化后的油滴表面的形貌。结果表明:BPSMA胶束具有优异的乳化效率,在极低的质量浓度下(0.25~1.00 mg/mL)亦可长期稳定乳液;BPSMA胶束所稳定的乳液具有明显的pH响应性,当pH≤6时,胶束呈球形颗粒状吸附并稳定于油水界面,当pH6时,胶束从油水界面脱离,乳液破乳;此外,BPSMA胶束作为颗粒乳化剂还具备良好的普适性,可以长效稳定碳酸二辛脂、辛酸丙基庚酯、硅油、棕榈酸异辛酯和润肤油脂等。     

光敏性双亲共聚物在水溶液中的胶束化行为

通过ε-己内酯改性丙烯酸酯(FAa，n=1～4)与肉桂酰氯间的酰化反应合成了一系列光敏性大单体(FAaC)，与甲基丙烯酸(MAA)在溶液中进行自由基聚合，制备了具有光敏性的双素无规共聚物(PMFAaC)。将PMFAaC在选择性溶剂中进行自组装，可以形成纳米结构的聚合物。用动态激光光散射(DLS)研究了聚合物胶束的溶液行为，同时考察了单体含量、聚合物终浓度、聚合物侧链长、pH值、离子强度及温度等因素对胶束粒径的影响。实验结果表明，PMFAaC在选择性溶剂中可自组装成胶束，其粒径及其分布对单体含量、聚合物终浓度、聚合物侧链长、pH值、离子强度等有一定的依赖性，而对温度无依赖性。进一步用紫外光使肉桂酰基发生交联反应。从而制备得到核交联且稳定的纳米胶束。用DIS表征发现交联后的胶束粒径较交联前的小。     

ARGET ATRP 与ROP 结合制备pH 响应两亲性聚合物分子刷及其自组装研究

结合电子转移活化剂再生-原子转移自由基聚合(ARGET ATRP)和开环聚合(ROP)法合成了一种具有无规疏水/ pH 响应结构的两亲性聚合物分子刷聚(甲基丙烯酸聚丙交酯酯-co-甲基丙烯酸)-b-聚甲基丙烯酸单甲氧基聚乙二醇酯 [P(PLAMA-co-MAA)-b-PPEGMA]. 通过核磁共振氢谱(¹H NMR)和凝胶渗透色谱(GPC)表征了聚合物的结构、分子量及分子量分布. 优化了反应条件并合成出分子量可控、分子量分布窄的聚合产物. 采用动态光散射法(DLS)、扫描电子显微镜(SEM)研究了聚合物分子刷在水溶液中自组装胶束的粒径、形貌及pH 响应行为. P(PLAMA-co-MAA)-b-PPEGMA 自组装形成粒径分布均匀的球形胶束. 且随着溶液pH 值从7 降低至3, 胶束中的PMAA 逐渐去离子化, 溶胀的胶束逐渐收缩, 粒径由200～300 nm 减小至150 nm 左右; 但当pH 值减小到2 以下, 胶束表面电荷量非常小, 胶束聚集, 使得粒径增大.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.