THE UNIFORMITY OF DISTRIBUTION OF SUBSTITUENTS ALONG THE CHAIN OF CARBOXYMETHYL CELLULOSE SYNTHESIZED IN TWO-PHASE MEDIUM C6H66——C2H5OH

 Based on the property that carboxymethylcellulose (CMC ) can be de-graded to anhydroglucose residues by cellulase, the rate constant (K) of enzymatic degra-dation of CMC synthesized in the benzene-ethanol medium has been determined. Further-morel experimental equation K = 2.71× 10^-2(DS)^-1.2 reflecting the relationship betweenK and the degree of substitution (DS) is correlated and used to describe chemical mi-crostructure uniformity of the distribution of substituents along chains effectively. Chain structure parameters of enzymatic degradation products of CMC — the number of chain breaks and the percentage of glucose released have been also measured.Average length of substituted and unsubstituted chain segments are calculated simultaneously.Through the study of static and dynamic procedures of enzymatic degradation,the method to characterize the distribution of substituents of CMC along the chain has been improved.     

羧甲基纤维素取代均一性的研究

羧基纤维素(钠盐,以下简称CMC)是一种重要的水溶性聚电解质。本文在传统溶媒法的基础上,采用乙醇作溶剂的两段加碱法新工艺制备CMC。研究表明,在低浴比(乙醇与纤维素质量比为2.04～2.45)条件下,采用新工艺制得的CMC具有较好的取代均一性和良好的性能:并用酶降解的方法,通过还原值测定,对CMC的取代基沿分子链的分布进行了表征;此外,对CMC的一些性能进行了测定,同时对其热稳定性进行了研究。     

丙烯酰胺与二(烯丙基)十二胺在羧甲基纤维素上的接枝共聚物合成与表征

以十二胺与 3 氯丙烯的反应物二 (烯丙基 )十二胺 (DALA)、丙烯酰胺 (AM)和羧甲基纤维素 (CMC)为原料 ,合成了疏水化水溶性两性纤维素接枝共聚物 (CGAL) .利用FTIR、1 H NMR、MS和元素分析 (EA)等方法确证了DALA的结构 .考察了CMC的取代度与浓度 ,AM、DALA与引发剂浓度 ,温度及pH等因素对接枝共聚的影响 .通过FTIR对CGAL进行了分析 .借助比色滴定、EA和GPC等手段测定了CGAL的组成与分子量 .TG分析和粘度法研究了CGAL及其溶液的热稳定性 .纤维素酶降解试验说明CGAL具有生物降解性     

Effect of pulp composition on the characteristics of residuals in CMC made from such pulps

Four different spruce sulphite pulp samples were used for the preparation of carboxymethylcellulose (CMC). The characteristics of the unreacted fibre and particle residuals obtained in the CMC-preparation were used to establish a correlation between the hemicellulose in the pulp and the intrinsic viscosity, i.e.,␣cellulose chain length and the occurence of unreacted residuals. It was shown that the residual particles in the CMC consisted of fibres, fibre fractions and gel particles of different degrees of substitution. The results suggested that pulps with long cellulose chains, i.e., pulps with high intrinsic viscosities, resulted in particles that were more substituted and more swollen. These pulps also resulted in more substituted hemicelluloses in the CMC and more substituted residuals. It was also suggested that galactoglucomannan in the cellulose pulps is favourable for the swelling which results in more substituted hemicelluloses in the CMC and more swollen residuals. The amount of residuals was influenced mainly by the characteristics of the cellulose in the pulp. It is therefore believed that a combination of high viscosity and a suitable combination of hemicelluloses is the most favourable way of eliminating the occurrence of undissolved residuals in CMC.     

烷基化程度对N-十八烷基化聚乙烯亚胺梳状高分子结构的影响

利用烷基化方法制备了烷基化取代程度(DS)介于47%～17.6%的N-十八烷基聚乙烯亚胺(PEI18C)梳状高分子.通过红外光谱、差示扫描量热法(DSC)、X-射线衍射和热失重分析等方法研究了PEI18C梳状高分子的结构、结晶行为和热稳定性,探讨了侧链烷基DS对C18侧链结晶及临界结晶行为的影响.结果发现,随DS的降低,PEI18C梳状高分子的结晶度由54.0%降至20.3%,可结晶碳原子数目由11.4个降到4.3个.受限于PEI骨架上C18烷基侧链的堆积排列模式并没有发生根本变化,仍以六方晶胞的形式进行排列.结果表明,侧链烷基DS或沿主链的侧链烷基分布密度对梳状高分子的结晶行为和临界结晶能力有明显的影响.从侧链结晶的角度,分析了侧链烷基取代度对梳状高分子结晶及热稳定性的影响.     

在苯-乙醇介质中生成的羧甲基纤维素取代基分布的研究

以三组份两相液体苯 乙醇 水为介质合成羧甲基纤维素（ＣＭＣ），应用１Ｈ ＮＭＲ谱图分析了ＣＭＣ中羧甲基在葡萄糖单元（ＡＧＵ）的Ｃ２、Ｃ３及Ｃ６位上对羟基的取代分布．结果表明，取代基的分布顺序是Ｃ６＞Ｃ２＞Ｃ３；当取代度（ＤＳ）低于１０时，Ｃ２∶Ｃ３∶Ｃ６近似于１４５∶１∶２１５；ＤＳ高于１０以后，分布趋于相同，通过对ＣＭＣ的Ｘ 衍射分析解释了取代基分布规律．同时研究了苯的影响，证实相同取代度下，在苯 乙醇 水中生成的ＣＭＣ试样，其Ｃ６位取代基分布多于在乙醇 水中生成的试样．     

POLYIONIC COMPLEXES DERIVED FROM POLYVINYL ALCOHOL Ⅱ. WATER ABSORBILITY AND ANTITHROMBOGENECITY OF PVA-TYPE POLYIONIC COMPLEXES*

Effect of both structure of substituents and degree of substitution of polyions derived from poly-vinyl alcohol on water-absorbility and antithrombogenecity of formed polyionic complexes (PIC)have been investigated. It was found that the water content of the PIC formed from p-formylben-zenesulfonic acid substituted PVA was higher than that of the PIC formed from p-formylbenzoicacid substituted PVA. When the substitution degree of polycation increased from 27% to 64%,the water content of the formed PIC increased from 170% to 1270%. Effect of water content andnet charge of PVA-type PIC on the antithrombogenecity was also investigated by plasma recalci-fication method.     

NMR Characterization of Substituted Aromatic Poly (Ether Sulofone)s

Abstract

The synthesis of a variety of substituted bisphenol A polysulfones, including nitro, amino, aminomethyl, ethyl, and methyl derivatives, is described. Nuclear magnetic resonance (NMR) (both proton and carbon, and several 2-D experiments) data confirm conclusions on the substitution site based on arguments on inductive effects in the phenyl rings. The proton ortho to the oxygen in the bisphenol A (BPA) residue is replaced in electrophilic substitution reactions. The degree of substitution was also calculated from the NMR results. The ethyl and methyl derivatives were expected, from the starting reactants, to each have a BPA ring substituted. The NMR data showed that, on the average, this is true. The nitro derivative also has substitution in every BPA ring, while the amino and aminomethyl derivatives have only intermittent BPA rings substituted. Measured degrees of substitution (DS) varied from 0.11 to 2.25.     

硅烷类外给电子体的取代基变化对丙烯聚合影响的研究

合成了2种新型硅烷化合物双环己基二甲氧基硅烷(Donor-H)、双哌啶二甲氧基硅烷(Donor-Py),将其与工业化的环己基甲基二甲氧基硅烷(Donor-C)分别作为外给电子体,用于MgCl2负载的Ziegler-Natta催化剂催化丙烯聚合,通过DSC、GPC、SSA和13C-NMR等分析手段研究了3种外给电子体取代基的变化对催化剂的催化活性、氢调敏感性、聚丙烯的等规度、分子量分布、结晶能力、等规序列分布的影响.结果表明,随着外给电子体取代基体积的增大,外给电子体的给电子能力逐渐增强.与Donor-C相比,随着外给电子体取代基体积的增大,合成的具有较大取代基的Donor-H和Donor-Py用于丙烯聚合时都表现优异的催化性能,特别是新型含有N杂原子的氨基硅烷类Donor-Py为外给电子体的催化剂的催化活性和制备的聚丙烯的等规度最高,聚丙烯的熔融指数可调范围最宽,结晶能力更强.氨基硅烷类Donor-Py制备的聚丙烯SSA热分级后的高等规组分含量最多,可高达64.5%,聚丙烯等规序列长度最长,聚丙烯的等规序列分布最窄,而且13C-NMR结果也表明聚丙烯等规序列长度MSL最长,聚丙烯的分子链最规整.     

Physico-chemical characterization of a cellulosic fraction from sugar beet pulp

The residue of sugar beet pulp from which pectin and alkaline soluble polysaccharides have been removed by microwave assisted extraction or conventional heat was treated with sodium monochloroacetate under alkaline pH to convert the residual cellulose present to carboxy methyl cellulose (CMC). Weight average molar masses ranged from about 96 to 220 × 10³ Daltons, weight average intrinsic viscosity from 1.9 to 4.1 dL/g and degree of substitution from 1.38 to 0.59. HPSEC with online molar mass detectors and Atomic Force Microscopy revealed that CMC was comprised of aggregated linear moieties in contact with spherical bodies. The linear portion was a mixture of rods and segmented rods. Some of the rods had long branches.     

聚对苯二甲酸乙二酯(PET)/聚对乙酰氧基甲酸(PHB)共聚酯及同类共聚物序列分布表征的数学统计

由聚对苯二甲酸乙二酯(PET)和对-乙酰氧基苯甲酸制得的PET/PHB共聚酯代表了一类序列结构较一般二元共聚物复杂的共聚体系.在揭示了这类共聚物与序列分布有关的诸概率参数中只有一个是独立的之后,定义了参数B_q来描述此类共聚物的无规度.并指出,共聚物B_q=b时的序列分布,可以从一般二元共聚物无规度B=b时的序列结构加以推断.     

THEORETICAL STUDIES ON THE SUBSTITUTION EFFECT OF FLUORINE ON ETHANE

<正> The substitution effect of fluorine on ethane has been investigated by means of studying the properties of the charge distribution at the bond critical points with the theory of atoms in molecule.It is found that the major substitution effects of fluorine atom are positive a inductive and polarity effect.At the same time,fluorine atom partially provides π electrons to other chemical bonds by means of hy-perconjugation in molecules with two fluorine atoms and one or two carbon atoms in the same plane,and these effects are reflected in the quantity of bond ellipticity,Laplacian and the charge density of charge distribution at the bond critical points.The substitution of hydrogen by fluorine in ethane strengthens all the bonds in substituted ethanes.Other effects originating from the substitution of hydrogen by fluorine have also been discussed.     

The influence of fibre wall thickness on the undissolved residuals in CMC solutions

An industrial calcium sulfite pulp was fractionated in a hydrocyclone to four fractions that differed in dimensions and composition due to differences in density. The intention was to investigate whether the fibre dimensions had any influence on the properties of carboxymethyl cellulose (CMC) produced from the fractions and especially how the properties of the unreacted material differed. It was surprisingly found that the fraction containing thin-walled fibres gave CMC and dissolved residuals in the CMC-solution that had the lowest degree of substitution (DS). It was therefore believed that the thin-walled fibres were collapsed and more closely bound in the fibre network after drying of the pulp and that this impeded the chemical diffusion in the subsequent CMC-process, i.e. the diffusion of the CMC-chemicals into the cell wall was slower. There was thus a correlation between thinner fibres and a lower degree of substitution for CMC made from such fibres. It was also found that tick-walled fibres had a higher degree of substitution than the thin-walled fibres but that the highest degree of substitution was obtained if a mixture of thin- and thick-walled fibres were used.     

ROLE OF HYDROXYL-BEARING AMINO ACIDS IN DIFFERENTIALLY TUNING THE ABSORPTION SPECTRA OF THE HUMAN RED AND GREEN CONE PIGMENTS

The human red and green cone pigments differ at either 15 or 16 amino acids, depending upon which polymorphic variants are compared. Seven of these amino acid differences involve the introduction or removal of a hydroxyl group. One of these differences, a substitution of alanine for senne at position 80, was found previously to produce a 5 nm blue shift. To determine the role of the remaining six hydroxyl group differences in tuning the absorption spectra of the human red and green pigments, we have studied six site-directed mutants in which single amino acids from the green pigment have been substituted for the corresponding residues in the red pigment. Blue shifts of 7 and 14 nm were observed upon substitution of phenylalanine for tyrosine at position 277 and alanine for threonine at position 285, respectively. Single substitutions at positions 65, 230, 233, and 309 produced spectral shifts of 1 nm or less. These data are in good agreement with a model based upon sequence comparisons among primate pigments and with the properties of site-directed mutants of bovine rhodopsin. Nonadditive effects observed in comparing the absorption spectra of red-green hybrid pigments remain to be explained.     

聚乙烯醇衍生的聚离子复合物的研究——Ⅱ.聚离子复合物的吸水性及抗凝血性

研究了聚乙烯醇型聚离子的取代度对所形成的复合物的含水率、抗凝血性的影响。聚乙烯醇型聚离子复合物水凝胶的含水率一般都在250％以上,最高者可达1270％。聚离子的取代度愈高,所形成复合物含水愈高,抗凝血性愈好。     

Study of the substitution pattern of hydroxyethylcellulose and its relationship to enzymic degradation

The concentration of completely unsubstituted anhydroglucose (AHG) units in hydroxyethylcellulose (HEC) at varying average number of moles of substituent (MS) is in accord with a reaction rate ratio of 3:1:10:10 for the etherification of the C₂, C₃, C₆, and side chain hydroxyls. Assuming random substitution along the cellulose chain at these relative reaction rates, the degree of substitution (DS), average poly(ethylene oxide) side-chain length, and probably frequency of isolated and multiple adjacent unsubstituted AHG units have been projected as functions of MS. Such estimates of DS and side-chain length compare favorably with actual measurements made on a variety of samples by other investigators below a substitution level of 2.0 MS. Reducing end, intrinsic viscosity, and ultracentrifuge data on enzymically hydrolyzed HEC's varying from 1.9 to 3.7 in MS indicate resistance to chain scission is a function of substitution, best expressed in terms of a proposed substitution index, the percentage of substituted AHG units. The rate of chain scission under carefully controlled conditions is initially rapid, tapering to a very slow, essentially steady level. On relating the frequency of chain breaks to the predicted substitution pattern of these samples, this behavior is interpreted to mean that scission occurs relatively rapidly at multiple contiguous unsubstituted sequences, but much more slowly adjacent to isolated unsubstituted AHG units. A possible mechanism of enzyme attack, correlating molecular chain breaks with glucose released, has been developed.     

聚对苯二甲酸乙二酯(PET)/聚对乙酰氧基甲酸(PHB)共聚酯及同类共聚物序列分布表征的数学统计

 由聚对苯二甲酸乙二酯(PET)和对-乙酰氧基苯甲酸制得的PET/PHB共聚酯代表了一类序列结构较一般二元共聚物复杂的共聚体系.在揭示了这类共聚物与序列分布有关的诸概率参数中只有一个是独立的之后,定义了参数B_q来描述此类共聚物的无规度.并指出,共聚物B_q=b时的序列分布,可以从一般二元共聚物无规度B=b时的序列结构加以推断.     

辐射交联制备改性CMC水凝胶的溶胀行为研究

利用丙烯酰胺 (AAm)接枝改性纤维素 ,然后进行羧甲基化反应得到高取代度的丙烯酰胺 羧甲基纤维素钠 (AAm CMC Na) .对该材料进行γ射线辐照制备出新型改性CMC水凝胶 .研究了这种水凝胶的溶胀动力学、交联动力学以及温度、pH值和无机盐浓度对水凝胶溶胀行为的影响 ,并与CMC Na水凝胶进行了比较 .结果表明 ,该水凝胶和CMC Na水凝胶相比 ,优点在于辐照交联所用的剂量下降 ,而且所需的CMC浓度减少 .AAm CMC Na水凝胶的溶胀度随温度升高而增大 ,在pH为 6～ 8范围内达到最大值 ,并随无机盐浓度与吸收剂量增加而下降 ,表现出较好的温度敏感性和pH敏感性 ,可望作为吸水材料和水保持剂     

Etude de copolymeres sequences de faible masse moleculaire utilises comme agents emulsifiants du type huile dans huile-associations en milieu solvant selectif

Polystyrene-polyisoprene blockcopolymers (Cop SI) of 20,000–50,000 molecular weight have been examined in solvents selective for each sequence (hexane and DMF) by viscometry, osmometry and ultracentrifugation. The degree of association or of micellisation can be obtained by comparing the characteristics of the copolymers in these selective solvents with those obtained in a common solvent e.g. toluene. A copolymer composition can be defined for which there exists a minimum of association. In the case of Cop SI, this minimum is at about 45 per cent weight polystyrene. The block-copolymers with the lowest degree of association, in both hexane and DMF, are the most efficient as oil-in-oil emulsifiers for the system DMF-hexane.     

Employing perichromism for probing the properties of carboxymethyl cellulose films: an expedient, accurate method for the determination of the degree of substitution of the biopolymer derivative

The properties of films of carboxymethyl cellulose, CMC, of different degree of substitution, DS, have been examined by the use of perichromic indicators (probes). The film properties that have been determined are: empirical polarity, E_T(33); “acidity”, α; “basicity”, β; and dipolarity/polarizability, π*. This has been achieved by employing the following perichromic probes: 4-nitroaniline, 4-nitroanisole, 4-nitro-N,N-dimethylaniline, and 2,6-dichloro-4-(2,4,6-triphenyl-pyridinium-1-yl)phenolate, WB. The correlations between both E_T(33)- or π* and DS were found to be linear; that between β and DS is a second order polynomial; no obvious correlation was found between α and DS. The polarities of CMC films are in the range of those of butyl alcohols. As models for CMC, we have employed cellulose plus CMC of high DS; oxidized cellulose with degree of oxidation = 0.5; sodium glucuronate. The former model behaved akin to CMC, but the plots of the perichromic properties versus DS showed different slopes/intercepts. FTIR data and molecular dynamics simulations on the solvation of WB have shown that this difference can be traced to more efficient hydrogen bonding between the film of the model and the probe. This affects the intra-molecular charge-transfer energy of the latter, leading to different responses to the variation of DS. Based on the excellent linear correlation between E_T(33) and DS, for CMC from different origins, we suggest that perichromism is a simple, accurate, and expedient alternative for the determination of DS of the biopolymer derivative.