Electrochemistry and voltammetric determination of tannic acid on a single-wall carbon nanotube-coated glassy carbon electrode

The voltammetric behavior of tannic acid (TA) on a single-wall carbon nanotubes (SWNTs) modified glassy carbon electrode has been investigated by cyclic voltammetry. TA can generate a well-defined anodic peak on the modified electrode at around 0.42 V (vs. SCE) in 0.10 M phosphate buffer solutions (pH = 4.0). The electrochemical reaction involves 1e transfer, accompanied by one proton. The electrode process is controlled by adsorption. The parameters affecting the response of TA, such as solution pH, accumulation time and accumulation potential are optimized for the determination of TA. Under the optimum conditions, the peak current changes linearly with the TA concentration in the range of 5.0 × 10⁻⁸–1.0 × 10⁻⁶ M. The lowest detectable concentration of TA is 8.0 × 10⁻⁹ M after 180 s accumulation. This method has been successfully applied to the determination of TA in tea and beer samples. In addition, the influence of potential interferents is examined. In the presence of bovine serum albumin, the peak current of TA decreases linearly due to the formation of a super-molecular complex.     

Adsorptive anodic stripping voltammetry of zirconium(IV)-alizarin red S complex at a carbon paste electrode

A sensitive adsorptive anodic stripping procedure for the determination of trace zirconium at a carbon paste electrode (CPE) has been developed. The method is based on adsorptive accumulation of the Zr(IV)-alizarin red S(ARS) complex onto the surface of the CPE, followed by oxidation of adsorbed species. The optimal experimental conditions include the use of 0.10 mol · L⁻¹ ammonium acetate buffer (pH 4.3), ARS, an accumulation potential of 0.20 V (versus SCE), an accumulation time of 2 min, a scan rate of 200 mV · s⁻¹ and a second-order derivative linear scan mode. The oxidation peak for the complex appears at 0.69 V. The peak current is proportional to the concentration of Zr(IV) over the range of 1.0 × 10⁻⁹–2.0 × 10⁻⁷ mol · L⁻¹, and the detection limit is 3 × 10⁻¹⁰ mol · L⁻¹ for a 2 min adsorption time. The relative standard deviations (n = 8) for 5.0 × 10⁻⁸ and 5.0 × 10⁻⁹ mol · L⁻¹ Zr(IV) are 3.3 and 4.8%, respectively. The proposed method was applied to the determination of zirconium in ore samples with satisfactory results.     

Electrochemical behavior and detection of guanine using a sodium montmorillonite-modified carbon paste electrode

Herein, a sodium montmorillonite-modified carbon paste electrode is described for the electrochemical determination of guanine. Guanine yields a well-defined and very sensitive oxidation peak at the sodium montmorillonite-modified carbon paste electrode. Compared with the unmodified carbon paste electrode, the modified electrode facilitates the electron transfer of guanine, since it notably increases the oxidation peak current and lowers the oxidation overpotential of guanine. Based on this, a simple sensitive reliable electrochemical method is proposed for the detection of guanine after all the experimental parameters, such as solution pH value, sodium montmorillonite content in the carbon paste electrode, accumulation potential, and time, are optimized. Under the optimized conditions, the oxidation peak current of guanine varies linearly with its concentration in the range 5.0×10⁻⁸ to 2.0×10⁻⁵ M and the detection limit (signal-to-noise=3) is 2.0×10⁻⁸ M after 4-min accumulation. This method is successfully demonstrated with urine samples. Published in Russian in Elektrokhimiya, 2006, Vol. 42, No. 2, pp. 178–182. The text was submitted by the authors in English.     

Simultaneous determination of uric acid and ascorbic acid at the film of chitosan incorporating cetylpyridine bromide modified glassy carbon electrode

A glassy carbon electrode (GCE) modified with the film composed of chitosan incorporating cetylpyridine bromide is constructed and used to determine uric acid (UA) and ascorbic acid (AA) by differential pulse voltammetry (DPV). This modified electrode shows efficient electrocatalytic activity and fairly selective separation for oxidation of AA and UA in mixture solution. UA is catalyzed by this modified electrode in phosphate buffer solution (pH 4.0) with a decrease of 80 mV, while AA is catalyzed with a decrease of 200 mV in overpotential compared to GCE, and the peak separation of oxidation between AA and UA is 260 mV, which is large enough to allow the determination of one in presence of the other. Under the optimum conditions, the anodic peak currents (I _pa) of DPV are proportional to the concentration of UA in the range of 2.0 × 10⁻⁶ to 6.0 × 10⁻⁴ M, with the detection limit of 5.0 × 10⁻⁷ M at a signal-to-noise ratio of 3 (S/N = 3) and to that of AA in the range of 4.0 × 10⁻⁶ to 1.0 × 10⁻³ M, with the detection limit of 8.0 × 10⁻⁷ M (S/N = 3).     

Simultaneous voltammetric determination of ascorbic acid and uric acid using a Nafion/multi-wall carbon nanotubes composite film-modified electrode

A Nafion/multi-wall carbon nanotubes (MWNT) composite film-modified electrode was fabricated. The modified electrode showed excellent electrocatalytic activity toward ascorbic acid (AA) and uric acid (UA) in 0.1-mol L⁻¹ NaCl medium (pH 6.5). Compared to the bare electrode that only displayed a broad and overlapped oxidation peak, the Nafion/MWNT film-modified electrode not only remarkably enhanced the anodic peak currents of AA and UA but also avoided the overlapping of the anodic peaks of AA and UA with a 320-mV separation of both peaks. Under the optimized conditions, the peak currents of AA and UA were proportional to their concentration at the ranges of 8.0 × 10⁻⁵ to 6.0 × 10⁻³ mol L⁻¹ and 6.0 × 10⁻⁷ to 8.0 × 10⁻⁵ mol L⁻¹, respectively. The proposed method was used for the detection of AA and UA in real samples with satisfactory results.     

Preconcentration and Voltammetric Study of Nicergoline at a Carbon Paste Electrode

 The electrochemical oxidation of nicergoline is investigated using cyclic and differential pulse voltammetry at a carbon paste electrode. For the determination of nicergoline an adsorptive stripping procedure is proposed. The response is characterized with respect to pH, ionic strength, preconcentration time, accumulation potential, nicergoline concentration, reproducibility and other variables. By differential pulse voltammetry at a carbon paste electrode and pH 8.0, a linear calibration in the range 5×10⁻⁸ M to 1×10⁻⁷ M and a detection limit of 1×10⁻⁸ M are obtained. The preconcentration medium-exchange approach was used for a selective determination of nicergoline in urine. For dilute urine samples a detection limit of 5×10⁻⁸ M is obtained after 3 min of accumulation and medium-exchange. The procedure also is applied for the determination of nicergoline in dosage form. Received August 24, 1998. Revision April 8, 1999.     

Electrochemical behaviors of GMP based on solid-phase extractionon at Cu-Mg-Al hydrotalcite-like compound (HTLC) modified glass carbon electrode

Guanosine-5′-monophosphate (GMP) was investigated the electrochemical behaviors based on solid-phase extractionon (SPE) at Cu-Mg-Al hydrotalcite-like compound (HTLC) modified glass carbon electrode. Cu-Mg-Al hydrotalcite-like compound (HTLC) was proved as a new sorbent for SPE of GMP, which showed an irreversible adsorption oxidation process on the HTLC/GCE with the oxidation peak potential located at 1.15 V (vs. SCE) in a pH 5.0 acetate buffer solution. Influencing factors of the electrochemical behavior of GMP on the HLTC/GCE were optimized and kinetic parameters were calculated. Under the optimal conditions, with differential pulse voltammetry (DPV), a linear relationship was obtained between the oxidation peak current and the GMP concentration in the range from 1.0 × 10^− 6 to 8.0 × 10⁻⁴ mol L⁻¹ with the detection limit as 5.0 × 10⁻⁷ mol L⁻¹ (signal-to-noise ratio of 3). The modified electrode surface has very good reproducibility and stability.     

Sensitive determination of fluphenazine at a dodecanethiol self-assembled monolayer-modified gold electrode, and its electrocatalysis to phenylephrine

Fluphenazine, an important tranquilizer, was found to undergo effective accumulation on dodecanethiol (DDT) self-assembled monolayer modified gold electrode (i.e. DDT/Au) and generated two anodic peaks at about 0.7 and 0.79 V (vs. SCE) in 0.05 M Na₂B₄O₇ (pH = 9.3) buffer solution. Sensitive and quantitative measurement of fluphenazine based on the former anodic peak was established under optimum conditions. The peak current was linear to fluphenazine concentration in the range from 5 × 10⁻⁷ to 5 × 10⁻⁵ M, with a detection limit of 5 × 10⁻⁹ M. This method was successfully applied to the determination of fluphenazine in drug tablets and proved to be reliable compared with UV spectrophotometry. In the presence of fluphenazine, the electrochemical oxidation of phenylephrine was catalyzed. The DDT self-assembled monolayer was characterized by Fourier transform infrared spectroscopy, surface Raman spectroscopy, X-ray photoelectron spectroscopy, electrochemical impedance spectroscopy, and electrochemical probing.     

Direct electrochemistry and electrocatalysis of nitrite based on nano-alumina-modified electrode

Simple and sensitive electrochemical method for the determination of nitrite, based on a nano-alumina-modified glassy carbon electrode (GCE), is described. Nitrite yields a well-defined oxidation peak whose potential is 0.74 V at the nano-alumina-coated GCE in 0.1 mol L⁻¹ phosphate buffer (pH 5.0). Compared with bare GCE, the nano-alumina-modified GCE has evident catalytic effect towards the oxidation of nitrite, and its peak current can be significantly enhanced. Some of the experimental parameters were optimized for the determination of nitrite. The oxidation peak current was proportional to nitrite concentration in the range of 5.0 × 10⁻⁸–1.1 × 10⁻³ mol L⁻¹, and a detection limit of 1.0 × 10⁻⁸ mol L⁻¹ was obtained. This method has been successfully used to the determination of nitrite in sausage sample. Furthermore, results obtained by the method have been compared with spectrophotometric method.     

Covalent modification of glassy carbon electrode with cysteine for the determination of dopamine in the presence of ascorbic acid

A covalently modified glassy carbon electrode with cysteine has been fabricated via an electrochemical oxidation procedure and was applied to induce the electrochemical differentiation between dopamine (DA) and ascorbic acid (AA). Based on the electrostatic interactions between the negatively charged groups on the electrode surface and DA and AA, the modified electrode enhanced the oxidation of DA, reducing the overpotential by 180 mV, and hindered the oxidation of AA, shifting the oxidation potential positively by 170 mV. The peak current for DA at the modified electrode was greatly enhanced and that for AA was significantly decreased, which allows the determination of DA in the presence of AA. The differential pulse peak current was linearly dependent on DA concentration over the range of 5 × 10⁻⁶–2 × 10⁻⁴ mol L⁻¹. The detection limit was 1.8 × 10⁻⁶ mol L⁻¹. The selectivity and sensitivity for dopamine is due to charge discrimination and analyte accumulation. The modified electrode has been applied to the determination of DA in the presence of AA. Correspondence: L. Zhang, Department of Chemistry, College of Life and Environmental Science, Shanghai Normal University, Guilin Rd 100, Shanghai 200234, P.R. China     

Electrocatalytic oxidation of quinine sulfate at a multiwall carbon nanotubes-ionic liquid modified glassy carbon electrode and its electrochemical determination

The electrocatalytic oxidation of quinine sulfate (QS) was investigated at a glassy carbon electrode, modified by a gel containing multiwall carbon nanotubes (MWCNTs) and room-temperature ionic liquid of 1-Butyl-3-methylimidazolium hexafluorophate (BMIMPF₆) in 0.10 M of phosphate buffer solution (PBS, pH 6.8). It was found that an irreversible anodic oxidation peak of QS with E _pa as 0.99 V appeared at MWCNTs-RTIL/glassy carbon electrode (GCE). The electrode reaction process was a diffusion-controlled one and the electrochemical oxidation involved two electrons transferring and two protons participation. Furthermore, the charge-transfer coefficient (α), diffusion coefficient (D), and electrode reaction rate constant (k _f) of QS were found to be 0.87, 7.89 × 10⁻³ cm²⋅s⁻¹ and 3.43 × 10⁻² s⁻¹, respectively. Under optimized conditions, linear calibration curves were obtained over the QS concentration range 3.0 × 10⁻⁶ to 1.0 × 10⁻⁴ M by square wave voltammetry, and the detection limit was found to be 0.44 μM based on the signal-to-noise ratio of 3. In addition, the novel MWCNTs-RTIL/GCE was characterized by the electrochemical impedance spectroscopy and the proposed method has been successfully applied in the electrochemical quantitative determination of quinine content in commercial injection samples and the determination results could meet the requirement.     

Fabrication of gold nanoparticles/polypyrrole composite-modified electrode for sensitive hydroxylamine sensor design

A highly sensitive hydroxylamine (HA) electrochemical sensor is developed based on electrodeposition of gold nanoparticles with diameter of 8 nm on the pre-synthesized polypyrrole matrix and formed gold nanoparticles/polypyrrole (GNPs/PPy) composite on glassy carbon electrode. The electrochemical behavior and electrocatalytic activity of the composite-modified electrode are investigated. The GNPs/PPy composite exhibits a distinctly higher electrocatalytic activity for the oxidation of HA than GNPs with twofold enhancement of peak current. The enhanced electrocatalytic activity is attributed to the synergic effect of the highly dispersed gold metal particles and PPy matrix. The overall numbers of electrons involved in HA oxidation, the electron transfer coefficient, catalytic rate constant, and diffusion coefficient are investigated by chronoamperometry. The sensor presents two wide linear ranges of 4.5 × 10⁻⁷–1.2 × 10⁻³ M and 1.2 × 10⁻³–19 × 10⁻³ M with the detection limit of 4.5 × 10⁻⁸ M (s/n = 3). In addition, the proposed electrode shows excellent sensitivity, selectivity, reproducibility, and stability properties.     

A New Differential Pulse Voltammetric Method for the Determination of Nitrate at a Copper Plated Glassy Carbon Electrode

 A differential pulse voltammetric method for the determination of nitrate has been described, which is applicable to the analysis of natural water samples with nitrate levels greater than 2.8 × 10⁻⁶ M. A reduction peak for the nitrate ions at a freshly copper plated glassy carbon electrode was observed at about −0.50 V vs Ag ∣AgCl∣KCl_satd electrode in a solution of 2.0 × 10⁻² M Cu²⁺, 0.5 M H₂SO₄ and 1.0 × 10⁻³ M KCl and exploited for analytical purposes. The working linear range was established by regression analysis and found to extend from 2.8 ×10⁻⁶ M to 8.0 × 10⁻⁵ M. The proposed method was applied for the determination of nitrate in natural waters. The detection limit of the method was 2.8 × 10⁻⁶ M and the sensitivity was 0.9683 A·L/mol. The possible interferences by some ions such as phosphate, nitrite and some halides were determined and found to lead to shifts of the peak position and increasing the peak heights. Received March 15, 1999. Revision July 9, 1999.     

Fast and sensitive determination of captopril by voltammetric method using ferrocenedicarboxylic acid modified carbon paste electrode

A ferrocenedicarboxylic acid modified carbon paste electrode was constructed and used as a fast and sensitive tool for the determination of captopril at trace level. It has been shown by direct current cyclic voltammetry and double step chronoamperometry that ferrocenedicarboxylic acid can catalyze the oxidation of captopril in aqueous buffer solution and produces a sharp oxidation peak current at about +0.49 vs. Ag/AgCl reference electrode. The square wave voltammetric peak currents of the electrode increased linearly with the corresponding captopril concentration in the range of 3.0 × 10⁻⁷–1.4 × 10⁻⁴M with a detection limit of 9.1 × 10⁻⁸ M. The influence of pH and potential interfering substances on the determination of captopril were studied. Electrochemical impedance spectroscopy was used to study the charge transfer properties at the electrode–solution interface. Finally, the sensor was examined as a selective, simple, and precise new electrochemical sensor for the determination of captopril in real samples, such as drug and urine, with satisfactory results.     

Electrochemical deposition of silicate–cetyltrimethylammonium bromide nanocomposite film on glassy carbon electrode for sensing of methyl parathion

A novel electrochemical sensor for methyl parathion based on silicate– cetyltrimethylammonium bromide nanocomposite film has been fabricated by electro-assisted deposition onto glassy carbon electrode in one-step via an electrochemical modulation of pH at the electrode/solution interface to promote controlled gelification of tetraethylorthosilicate sol, and was characterized with scanning electron microscopy, X-ray diffraction, and electrochemical impedance spectroscopy. The electrochemical sensing of methyl parathion on the film-modified electrode was investigated applying cyclic voltammetry and square wave voltammetry. Compared to the unmodified electrode, the shapes of the redox peaks were improved and the peak currents significantly increased. Experimental parameters such as deposition time, pH value, and accumulation conditions have been optimized. A linear relationship between the peak current and methyl parathion concentration was obtained in the range from 1.0 × 10⁻⁷ to 1.0 × 10⁻⁴ mol L⁻¹ with a detection limit of 1.04 × 10 ⁻⁸ mol L⁻¹ (S/N = 3) after accumulation at 0 V for 120 s. The film electrode shows great promise for determination of methyl parathion in real samples.      

Electrochemical methods for simultaneous determination of trace amounts of dopamine and uric acid using a carbon paste electrode incorporated with multi-wall carbon nanotubes and modified with α-cyclodextrine

In this work, we investigate the electrochemical activity of dopamine (DA) and uric acid (UA) using both a bare and a modified carbon paste electrode as the working electrode, with a platinum wire as the counter electrode and a silver/silver chloride (Ag/AgCl) as the reference electrode. The modified carbon paste electrode consists of multi-walled carbon nanotubes (>95%) treated with α-cyclodextrine, resulting in an electrode that exhibits a significant catalytic effect toward the electro-chemical oxidation of DA in a 0.2-M Britton–Robinson buffer solution (pH 5.0). The peak current increases linearly with the DA concentration within the molar concentration ranges of 2.0 × 10⁻⁶ to 5.0 × 10⁻⁵ M and 5.0 × 10⁻⁵ to 1.9 × 10⁻⁴ M. The detection limit (signal to noise >3) for DA was found to be 1.34 × 10⁻⁷ M, respectively. In this work, voltammetric methods such as cyclic voltammetry, chronoamperometry, chronocuolometry, differential pulse and square wave voltammetry, and linear sweep and hydrodynamic voltammetry were used. Cyclic voltammetry was used to investigate the redox properties of the modified electrode at various scan rates. The diffusion coefficient (D, cm² s⁻¹ = 3.05 × 10⁻⁵) and the kinetic parameters such as the electron transfer coefficient (α = 0.51) and the rate constant (k, cm³ mol⁻¹ s⁻¹ = 1.8 × 10³) for DA were determined using electrochemical approaches. By using differential pulse voltammetry for simultaneous measurements, we obtained two peaks for DA and UA in the same solution, with the peak separation approximately 136 mV. The average recovery was measured at 102.45% for DA injection.     

Electroreduction and Quantification of Furazolidone and Furaltadone in Different Media

 Adsorptive cathodic stripping voltammetry was used for the determination of furazolidone (FZ) and furaltadone (FD) in borax and phosphate buffers, respectively, using HMDE as working electrode. The influence of different factors upon the peak current response such as accumulation potential, scan rate, preconcentration time, pH and other variables was studied. Furazolidone and furaltadone showed an adsorption character on HMDE in presence of borax and phosphate buffers, respectively. A single cathodic peak at −0.36 V in borax (pH = 9.5) was observed for FZ, while FD gave a cathodic peak at −0.32 V in phosphate buffer (pH = 8.5). The calibration graph showed a linear behavior over the range 3×10⁻⁹–9×10⁻⁸ mol dm⁻³ for furazolidone. In the case of FD, concentrations from 3×10⁻⁹ to 2×10⁻⁷ mol dm⁻³ gave a linear relationship with the peak current. A detection limit of 2×10⁻⁹ mol dm⁻³ and 1×10⁻⁹ mol dm⁻³ was obtained for furazolidone and furaltadone, respectively. This method was applied to determine these drugs in pharmaceutical formulations, urine and serum samples. Received December 15, 1998. Revision February 4, 2000.     

Application of a Single-Wall Carbon Nano-Tube Film Electrode to the Determination of Trace Amounts of Folic Acid

Single-wall carbon nano-tubes were used to modify the surface of a glassy carbon electrode (GC) and applied in the determination of folic acid with voltammetry. The experiments demonstrated that the presence of a carbon nano-tube film on the electrode greatly increased the reduction peak current of folic acid. Cyclic voltammetry (CV) and linear sweep voltammetry (LSV) were used in a comparative investigation of the electrochemical reduction of folic acid with the film electrode. Effects of pH on the peak current and the peak potential were studied in the pH range of 4.0–8.0 with Britton-Robinson buffer solution. The reduction peak current was found to be linearly related to folic acid concentration over the range of 1 × 10⁻⁸ to 1 × 10⁻⁴ mol L⁻¹ with a detection limit of 1 × 10⁻⁹ mol L⁻¹ after 5 min accumulation. The film electrode provides an efficient way for eliminating interferences from some inorganic and organic species in the solution. The high sensitivity, selectivity and stability of the film electrode demonstrate its practical application from a simple and rapid determination of folic acid in tablets.     

Simultaneous and sensitive determination of procaine and its metabolite for pharmaceutical quality control and pharmacokinetic research by using a graphite paste electrode

A simple, rapid, sensitive, and accurate method for simultaneous electrochemical determination of procaine and its metabolite (p-aminobenzoic acid, PABA) for pharmaceutical quality control and pharmacokinetic research was developed using a graphite paste electrode. The differential pulse voltammetric results revealed that procaine and p-aminobenzoic acid, respectively, showed well-defined anodic oxidation peaks on a carbon paste electrode with a current peak separation of 155 mV at a scan rate of 100 mV s⁻¹. This well separation of the current peaks for these two compounds in voltammetry enables us to simultaneously determine them. Good linearity (r > 0.998) between oxidation peak current and concentration was obtained in the range of 5.0 × 10⁻⁷–5.0 × 10⁻⁵ M for procaine and 5.0 × 10⁻⁷–2.0 × 10⁻⁵ M for PABA in pH 4.50 acetate buffer solution. The detection limit for both analytes is 5 × 10⁻⁸ M (S/N = 3:1). The present voltammetric method has been successfully used to determine trace p-aminobenzoic acid in procaine hydrochloride injection and procaine in plasma with a linear relationship of current to its concentration ranging from 1.0 × 10⁻⁶ to 5.0 × 10⁻⁵ M (correlation coefficient of 0.9981) with a low detection limit of 5.0 × 10⁻⁷ M (S/N = 3:1). This validated method is promising to the study of pharmacokinetics in Sprague–Dawley rat and rabbit plasma after an intravenous administration of procaine hydrochloride injection.     

Sensitive voltammetric determination of 2-mercaptobenzimidazole at electropolymerized nickel and copper tetraaminophthalocyanine membrane modified electrode

The voltammetric determination of 2-mercaptobenzimidazole (MBI) was studied by using a glassy carbon electrode (GCE) coated with polymeric nickel and copper tetraaminophthalocyanine (poly-NiTAPc and poly-CuTAPc) membrane. The polymeric membrane decreases the overpotential of oxidation of MBI by 136.2 and 115.0 mV and increases the oxidation peak current by about 3.4 and 3.3 times, while the reduction peak potential shifts positively by 113.0 and 84.1 mV and the peak current increases by about 10 and 7 times in 0.1 mol·l⁻¹ phosphate buffer solution (PBS) at pH = 2.0 for poly-NiTAPc and poly-CuTAPc, respectively, compared to the unmodified GCE. The results indicated that the developed electrode exhibited efficient electrocatalytic activity for MBI with relatively high sensitivity, stability, and long life. The oxidation and reduction peak currents of MBI were linear to its concentrations ranging from 8.0 × 10⁻⁵ to 1.0 × 10⁻³ mol·l⁻¹ at poly-NiTAPc and from 2.0 × 10⁻⁵ to 1.0 × 10⁻³ mol·l⁻¹ at poly-NiTAPc membranes modified electrodes, respectively, with a low limit of detection.