Electro‐optical properties of electropolymerized poly(3‐hexylthiophene)/carbon nanotube composite thin films

3‐hexylthiophene was electropolymerized on a carbon nanotube (CNT)‐laden fluorine‐doped tin oxide substrate. Scanning electron microscopy and Raman spectroscopy revealed that the polymer was infused throughout the thickness of the 150‐nm thick CNT mat, resulting in a conducting composite film with a dense CNT network. The electropolymerized poly(3‐hexylthiophene) (e‐P3HT)/CNT composites exhibited photoluminescence intensity quenching by as much as 92% compared to the neat e‐P3HT, which provided evidence of charge transfer from the polymer phase to the CNT phase. Through‐film impedance and J‐V measurements of the composites gave a conductivity (σ) of 1.2 × 10^?10 S cm^?1 and zero‐field mobility (μ₀) of 8.5 × 10^?4 cm² V^?1 s^?1, both of which were higher than those of neat e‐P3HT films (σ = 9.9 × 10^?12 S cm^?1, μ₀ = 3 × 10^?5 cm² V^?1 s^?1). In electropolymerized samples, the thiophene rings were oriented in the (010) direction (thiophene rings parallel to substrate), which resulted in a broader optical absorbance than for spin coated samples, however, the lack of long‐range conjugation caused a blueshift in the absorbance maximum from 523 nm for unannealed regioregular P3HT (rr‐P3HT) to 470 nm for e‐P3HT. Raman spectroscopy revealed that π‐π stacking in e‐P3HT was comparable to that in rr‐P3HT and significantly higher than in regiorandom P3HT (ran‐P3HT) as shown by the principal Raman peak shift from 1444 to 1446 cm^?1 for e‐P3HT and rr‐P3HT to 1473 cm^?1 for ran‐P3HT. This work demonstrates that these polymer/CNT composites may have interesting properties for electro‐optical applications. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1269–1275, 2011     

Regioregular poly(3‐alkanoylthiophene): Synthesis and electrochemical,photophysical, charge transport,and photovoltaic properties

Head‐to‐tail regioregular poly(3‐heptanoylthiophene) (PHOT) was synthesized by Ni‐catalyzed polycondensation of the 2,2‐dimethyl‐1,3‐propanediol‐protected Grignard monomer followed by deprotection. Cyclic voltammetric (CV) study demonstrates that the highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) of PHOT are 0.5 eV lower in energy than those of the head‐to‐tail poly(3‐hexylthiophene) (HT‐P3HT). Their optical band gaps are essentially the same. Incomplete photoluminescence (PL) quenching was observed in thin films of the 1:1 blend of PHOT and HT‐P3HT. PHOT displayed a glass transition at ～269 °C and decomposed at ～300 °C according to differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Wide‐angle X‐ray diffraction (WAXD) study showed that PHOT exists in a not highly ordered state in solid films especially in the π‐stacking direction. Only p‐channel activity was observed in field‐effect transistors (FETs) for PHOT. The hole mobility was on the order of 10^?4 cm² V^?1 s^?1. Photovoltaic devices with an active layer of 1:1 blend of PHOT and PC₇₁BM had a power conversion efficiency (PCE) of ～0.5%. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

High‐performance field‐effect transistors based on furan‐containing diketopyrrolopyrrole copolymer under a mild annealing temperature

Two furan‐flanked polymers poly{3,6‐difuran‐2‐yl‐2,5‐di(2‐octyldodecyl)‐pyrrolo[3,4‐c]pyrrole‐1,4‐dione‐alt‐thienylenevinylene} (PDVFs), with a highly π‐extended diketopyrrolopyrrole backbone, are developed for solution‐processed high‐performance polymer field‐effect transistors (FETs). Atomic force microscopy and grazing incidence X‐ray scattering analyses indicate that PDVF‐8 and PDVF‐10 films exhibit a similar nodular morphology with the ultrasmall lamellar distances of 16.84 and 18.98 Å, respectively. When compared with the reported polymers with the same alkyl substitutes, this is the smallest d‐spacing value observed to date. This closed lamellar crystallinity facilitates charge carrier transport. Therefore, polymer thin‐film transistors fabricated from as‐spun PDVF‐8 films exhibit a high hole mobility exceeding 1.0 cm² V^?1 s^?1 with a current on/off ratio above 10⁶. After annealing treatment at 100 °C in air, the highest hole mobility of PDVF‐8‐based FETs was significantly improved to 1.90 cm² V^?1 s^?1, which is among the highest values of the reported FET devices fabricated from polymer thin films based on this mild annealing temperature. In contrast, long alkyl‐substituted PDVF‐10 exhibited a relatively low hole mobility of 1.65 cm² V^?1 s^?1 mainly resulting from low molecular weight. This work demonstrated that PDVFs would be promising semiconductors for developing cost‐effective and large‐scale production of flexible organic electronics. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1970–1977     

Synthesis,morphology, and field‐effect transistor characteristics of new crystalline–crystalline diblock copolymers of poly(3‐hexylthiophene‐block‐steryl acrylate)

We report the synthesis, morphology, and charge‐transporting characteristics of new crystalline–crystalline diblock copolymers, poly(3‐hexylthiophene‐block‐stearyl acrylate) (P3HT‐b‐PSA). Three different diblock copolymers, P1 , P2 , and P3 , with P3HT/PSA polymerization degree block ratios of 60/26, 60/50, and 60/360, respectively, were prepared for investigating the morphology‐property relationship and the dependence of optoelectronic properties on the block copolymer structure. Small‐ and wide‐angle X‐ray scattering indicated the presence of both P3HT and PSA crystalline domains and the presence of microphase separation among blocks. The transmission electron microscopy and atomic force microscopy results revealed that the diblock copolymers cast from chlorobenzene, tended to form needle‐like morphologies. The field‐effect mobilities of the diblock copolymers deposited on untreated SiO₂ substrates, decreased with increasing PSA block length. In a sharp contrast, the mobilities enhanced with increasing PSA content when the P3HT‐b‐PSA was deposited on phenyltrichlorosilane (PTS)‐treated substrates. The copolymers with a 60/360 P3HT/PSA ratio showed a good mobility of 4 × 10^?3 cm² V^?1 s^?1 and a high on/off ratio of 7 × 10⁶ on PTS‐treated substrates. This study highlighted the importance of the block ratio, the substrate and self‐assembly structures on the charge transport characteristics of the crystalline–crystalline conjugated diblock copolymers. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Simultaneous morphological stability and high charge carrier mobilities in donor–acceptor block copolymer/PCBM blends

Donor–acceptor block copolymers (BCP), incorporating poly(3‐hexylthiophene) (P3HT), and a polystyrene copolymer with pendant fullerenes (PPCBM) provide desired stable nanostructures, but mostly do not exhibit balanced charge carrier mobilities. This work presents an elegant approach to match hole and electron transport in BCP by blending with molecular PCBM without causing any macrophase separation. An insufficient electron mobility of PPCBM can be widely compensated by adding PCBM which is monitored by the space‐charge limited current method. Using X‐ray diffraction, atomic force microscopy, and differential scanning calorimetry, we verify the large miscibility of the PPCBM:PCBM blend up to 60 wt % PCBM load forming an amorphous, molecularly mixed fullerene phase without crystallization. Thus, blending BCP with PCBM substantially enhances charge transport achieving an electron mobility of μ_e=(3.2 ± 1.7) × 10^?4 cm²V^?1s^?1 and hole mobility of μ_h=(1.8 ± 0.6) × 10^?3 cm²V^?1s^?1 in organic field‐effect transistors (OFET). The BCP:PCBM blend provides a similarly high ambipolar charge transport compared to the established P3HT:PCBM system, but with the advantage of an exceptionally stable morphology even for prolonged thermal annealing. This work demonstrates the feasibility of high charge transport and stable morphology simultaneously in a donor–acceptor BCP by a blend approach. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1125–1136     

A High‐Performance Organic Field‐Effect Transistor Based on Platinum(II) Porphyrin: Peripheral Substituents on Porphyrin Ligand Significantly Affect Film Structure and Charge Mobility

Organic field‐effect transistors incorporating planar π‐conjugated metal‐free macrocycles and their metal derivatives are fabricated by vacuum deposition. The crystal structures of [H₂(OX)] (H₂OX=etioporphyrin‐I), [Cu(OX)], [Pt(OX)], and [Pt(TBP)] (H₂TBP=tetra‐(n‐butyl)porphyrin) as determined by single crystal X‐ray diffraction (XRD), reveal the absence of occluded solvent molecules. The field‐effect transistors (FETs) made from thin films of all these metal‐free macrocycles and their metal derivatives show a p‐type semiconductor behavior with a charge mobility (μ) ranging from 10^?6 to 10^?1 cm² V^?1 s^?1. Annealing the as‐deposited Pt(OX) film leads to the formation of a polycrystalline film that exhibits excellent overall charge transport properties with a charge mobility of up to 3.2×10^?1 cm² V^?1 s^?1, which is the best value reported for a metalloporphyrin. Compared with their metal derivatives, the field‐effect transistors made from thin films of metal‐free macrocycles (except tetra‐(n‐propyl)porphycene) have significantly lower μ values (3.0×10^?6–3.7×10^?5 cm² V^?1 s^?1).     

Synthesis and FET characterization of novel ambipolar and low‐bandgap naphthalene‐diimide‐based semiconducting polymers

A novel series of naphthalene‐diimide‐based semiconducting polymers ( P1–P4 ) containing benzodithiophene or dithienopyrrole were successfully synthesized for ambipolar semiconducting materials showing near infrared absorptions. The incorporation of a 3‐hexylthiophene (3HT) spacer extended the intramolecular charge‐transfer (ICT) peak from λ_onset = 739 nm ( P1 ) to 785 nm ( P3 ). Moreover, about 250 nm red‐shift of the ICT peaks was observed in P2 and P4 compared to P1 and P3 due to the increased high‐lying HOMO energy levels. The grazing incidence X‐ray scattering of the P3 and P4 films proved the slightly improved crystalline order in the π?π stacking direction, indicating that the planar backbone is probably due to the introduced 3HT. The P1–P4 ‐based field‐effect transistor showed n‐type dominant ambipolar characteristics. The P2 and P4 showed higher electron mobilities up to 1.5 × 10^?2 cm² V^?1 s^?1 than P1 and P3 , which might be influenced by the orientation of the polymer backbone and the intermolecular orbital overlap. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 359–367     

Synthesis and characterization of cyclic P3HT as a donor polymer for organic solar cells

In this study, cyclic poly(3‐hexylthiophene‐2,5‐diyl) (c‐P3HT) with a controlled M_n was synthesized by the intramolecular cyclization of α‐bromo‐ω‐ethynyl‐functionalized P3HT via the Sonogashira coupling reaction. The effect of the cyclic structure, which does not have terminal groups of polymers, on the photoelectric conversion characteristics was investigated in comparison to linear P3HT (l‐P3HT). c‐P3HT was successfully synthesized with M_n ≈ 17,000, dispersity ≈ 1.2, and regioregularity ≈ 99%. The hole mobility was determined to be 5.1 × 10^?4 cm² V^?1 s^?1 by time‐of‐flight (TOF) experiment. This was comparable to that of l‐P3HT of 5.6 × 10^?4 cm² V^?1 s^?1. Organic solar cell systems were fabricated with each polymer by blending them with [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM). The l‐P3HT:PC₇₁BM system showed a dispersive TOF photocurrent profile for electron transport, whereas a nondispersive profile was observed for c‐P3HT:PC₇₁BM. In addition, an amount of collected electrons in c‐P3HT:PC₇₁BM was greater than that in l‐P3HT:PC₇₁BM for TOF experiments. The photoelectric conversion characteristics were improved by using c‐P3HT rather than l‐P3HT (power conversion efficiency [PCE] = 4.05% vs 3.23%), reflecting the nondispersive transport and the improvement of electron collection. PCEs will be much improved by applying this cyclic concept to highly‐efficient OSC polymers. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 266–271     

聚吡咯薄膜的电特性

含有不同的链长的w-吡咯烷基二甲基氯硅烷作为粘合剂通过自组装（SAMs）吸附于二氧化硅表面,然后聚吡咯膜化学沉积于该粘合剂修饰的表面。化学沉积的聚吡咯膜的表面形貌用扫描电镜（SEM）及原子力显微镜（AFM）表征。除短链外不同链长的粘合剂对聚吡咯膜的厚度影响不大。聚吡咯膜的电特性用电流-电压表征。结果显示电流与粘合剂的链长无关。电特性表明载流子迁移率为1.4 ´ 10-4 cm2×V-1.s –1。     

Two‐Step direct arylation for synthesis of naphthalenediimide‐based conjugated polymer

A naphthalenediimide (NDI)‐based conjugated polymer was synthesized by a two‐step direct C‐H arylation sequence. In the first step, two ethylenedioxythiophene units were coupled to NDI by direct arylation. In the second step, the direct arylation polycondensation of the monomer, formed in the first step, with 2,7‐dibromo‐9,9‐dioctylfluorene afforded the corresponding NDI‐based conjugated polymer ( PEDOTNDIF ) with molecular weight of 21,500 in 91% yield. The optical and electrochemical properties of the polymer were evaluated. The polymer showed ambipolar behavior in organic field‐effect transistors (OFETs). The electron mobility of PEDOTNDIF was estimated to be 2.3 × 10^?6 cm² V^?1 s^?1 using an OFET device with source‐drain (S‐D) Au electrodes. A modified OFET device with S‐D MgAg electrodes increased the electron mobility for PEDOTNDIF to 1.0 × 10^?5 cm² V^?1 s^?1 due to the more suitable work function of these electrodes, which reduced the injection barrier to the semiconducting polymer. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1401–1407     

Linking polythiophene chains with vinylene‐bridges: A way to improve charge transport in polymer field‐effect transistors

A series of novel branched polythiophene derivatives bearing different densities of vinylene‐bridges as linking chains were synthesized by a general synthetic strategy. The organic field‐effect transistors, which were fabricated by spin‐coating the polymer solutions onto octadecyltrichlorosilane‐modified SiO₂/Si substrates with top‐contact configuration, afforded a high mobility of 8.0 × 10^?3 cm² V^?1 s^?1 with an on/off ratio greater than 10⁴ and a threshold voltage of about ?3 V in saturation regime. The devices based on these polymers possessed better performance than those of polymers without conjugated bridges and polymers with longer conjugated bridges. These results demonstrated that the combination of conjugated polythiophene backbones and vinylene‐bridges would improve the carrier mobility. As an emerging class of conjugated materials, polymers with vinylene‐bridges as linking chains would open up new opportunities in organic electronics, and their applications in organic electronics are promising. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1381–1392, 2009     

Conductive triethylene glycol monomethyl ether substituted polythiophenes with high stability in the doped state

Synthesis of two conducting polymers containing 3‐hexylthiophene and 3‐[2‐(2‐(2‐methoxyethoxy)ethoxy)ethoxy]thiophene is demonstrated. In thin‐film transistors, the high‐molecular‐weight polymer shows an average mobility of 4.2 × 10^?4 cm² V^?1 s^?1. Most importantly, the polymers have high conductivity upon doping with iodine and also have high stability in the doped state with high conductivities measured even after 1 month. Furthermore, the doping causes transparency to thin films of the polymer and the films are resistant to common organic solvents. All these properties indicate a great potential for the iodine‐doped polymer to be used as an alternative to commercially available poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate). © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 1079–1086     

Diketopyrrolopyrrole‐based acceptor–acceptor conjugated polymers: The importance of comonomer on their charge transportation nature

Besides the donor–acceptor (D–A) type, acceptor–acceptor (A–A) polymers are another class of important alternative conjugated copolymers, but have been less studied in the past. In this study, two kinds of A–A polymers, P1 and P2 , have been designed and synthesized based on diketopyrrolopyrrole in combination with the second electron‐deficient unit, perylenediimide or thieno[3,4‐c]pyrrole‐4,6‐dione. UV–vis absorption spectroscopy revealed that these two kinds of polymers have a band gap of 1.28–1.33 eV. Their highest occupied molecular orbital and lowest unoccupied molecular orbital energy levels are around ?5.6 and ?4.0 eV for P1 polymers, whereas ?5.4 and ?3.7 eV for P2 polymers, respectively. Density functional theory study disclosed that P1 backbone is in a vastly twisting state, whereas that of P2 is completely planar. Furthermore, organic field‐effect transistor devices were fabricated using these two kinds of polymers as the active material. Of interest, the devices based on P1 polymers displayed n‐channel behaviors with an electron mobility in the order of 10^?4 cm² V^?1 s^?1. In contrast, the P2 ‐based devices exhibited only p‐channel charge transportation characteristics with a hole mobility in the order of 10^?3 cm² V^?1 s^?1. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2356–2366     

Hybrid phospholipid bilayer coatings for separations of cationic proteins in capillary zone electrophoresis

Protein separations in CZE suffer from nonspecific adsorption of analytes to the capillary surface. Semipermanent phospholipid bilayers have been used to minimize adsorption, but must be regenerated regularly to ensure reproducibility. We investigated the formation, characterization, and use of hybrid phospholipid bilayers (HPBs) as more stable biosurfactant capillary coatings for CZE protein separations. HPBs are formed by covalently modifying a support with a hydrophobic monolayer onto which a self‐assembled lipid monolayer is deposited. Monolayers prepared in capillaries using 3‐cyanopropyldimethylchlorosilane (CPDCS) or n‐octyldimethylchlorosilane (ODCS) yielded hydrophobic surfaces with lowered surface free energies of 6.0 ± 0.3 or 0.2 ± 0.1 mJ m^?2, respectively, compared to 17 ± 1 mJ m^?2 for bare silica capillaries. HPBs were formed by subsequently fusing vesicles comprised of 1,2‐dilauroyl‐sn‐glycero‐3‐phosphocholine or 1,2‐dioleoyl‐sn‐glycero‐3‐phosphocholine to CPDCS‐ or ODCS‐modified capillaries. The resultant HPB coatings shielded the capillary surface and yielded reduced electroosmotic mobility (1.3–1.9 × 10^?4 cm² V^?1s^?1) compared to CPDCS‐ and ODCS‐modified or bare capillaries (3.6 ± 0.2 × 10^?4 cm² V^?1s^?1, 4.8 ± 0.4 × 10^?4 cm² V^?1s^?1, and 6.0 ± 0.2 × 10^?4 cm² V^?1s^?1, respectively), with increased stability compared to phospholipid bilayer coatings. HPB‐coated capillaries yielded reproducible protein migration times (RSD ≤ 3.6%, n ≥ 6) with separation efficiencies as high as 200 000 plates/m.     

Synthesis and photovoltaic properties of conjugated D–A copolymers based on thienyl substituted pyrene and diketopyrrolopyrrole for polymer solar cells

A new donor‐acceptor conjugated copolymer (PDTPyDPP), comprising 2,7‐di‐2‐thienyl‐4,5,9,10‐tetrakis(hexyloxy)pyrene as a donor and diketopyrrolopyrrole (DPP) as an acceptor, was synthesized. PDTPyDPP showed good solubility in common organic solvents, broad visible absorption from 300 to 900 nm, and a moderate hole mobility up to 6.3 × 10^?3 cm² V^?1 s^?1. The power conversion efficiency of the photovoltaic device based on the PDTPyDPP/PC₇₁BM photoactive layer reached 4.43% with 0.66 V of open‐circuit voltage (V_oc), 10.52 mA cm^?2 of short‐circuit current (J_sc) and 64.11% of fill factor. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3198–3204     

P4VP and oligo(phenylenevinylene)‐perylenebisimide mixed donor‐acceptor supramolecular comb polymer complexes with improved charge carrier mobility

Random donor‐acceptor (D‐A) supramolecular comb polymers were formed when hydroxyl functionalized donor and acceptor small molecules based on Oligo(phenylenevinylene) (named OPVCN‐OH ) and Perylenebisimide (named UPBI‐PDP ), respectively, were complexed with Poly(4‐vinyl pyridine) (P4VP). A series of random D‐A supramolecular comb polymers were formed by varying the ratios of UPBI‐PDP and OPVCN‐OH with P4VP. A 100% P4VP‐donor polymer complex [ P4VP(OPV_1.00 )] and a 100% P4VP‐acceptor polymer complex [ P4VP(UPBI_1.00 )] were also synthesized and characterized. Complex formation was confirmed by FT‐IR and ¹H NMR spectroscopy. Solid state structural studies carried out using small angle X‐ray scattering and wide angle X‐ray diffraction experiments revealed altered packing of the D and A molecules in the complexes. Transmission electron microscopy images showed lamellar structures in the < 10 nm scale for the P4VP(OPV_1.00 ), P4VP(UPBI_1.00 ), and mixed P4VP (D‐A) complexes. The effect of the nanoscopic D‐A self‐assembly on the bulk mobility of the materials was probed using SCLC measurements. The mixed D‐A random complexes exhibited ambipolar charge transport characteristics with higher values for the average bulk hole mobility estimate. P4VP(OPV_0.25 + UPBI_0.75) exhibited an average hole mobility in the order of 10^?2cm² V^?1 s^?1 and electron mobility 10^?5cm² V^?1 s^?1. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2403–2412     

Syntheses,properties, and field‐effect transistors of small band gap quinoxaline‐ and thienopyrazine‐vinylene/ethynylene conjugated polymers

New conjugated copolymers of quinoxaline (AQ) and thienopyrazine (ATP) with vinylene (V) or ethynylene (E), poly[2,3‐bis(4‐(2‐ethylhexyloxy)phenyl)‐quinoxaline vinylene] (PAQV), poly[2,3‐bis(4‐(2‐ethylhexyloxy)phenyl)‐quinoxaline ethynylene)] (PAQE), poly[2,3‐bis(4‐(2‐ethylhexyloxy)phenyl)‐thieno[3,4‐b]pyrazine vinylene] (PATPV), and poly[2,3‐bis(4‐(2‐ethylhexyloxy)phenyl)‐thieno[3,4‐b]pyrazine ethynylene] (PATPE), were successfully synthesized by Stille coupling reaction. The optical band gaps of the PAQV, PAQE, PATPV, and PATPE were 1.86, 2.00, 0.88, and 0.90 eV, respectively, whereas the electrochemical band gaps were 1.99, 2.06, 1.00, and 1.06 eV, respectively. The reduced steric hindrance by the incorporation of the V or E linkage or the intramolecular charge transfer between the acceptor and the V or E linkage led to the small band gap. The AQ/ATP‐vinylene copolymers exhibited much higher vis/near infrared absorption intensity than the AQ/ATP‐ethynylene suggested the stronger π–π* transition intensity in the former and led to better charge‐transporting characteristics. The saturation field‐effect hole mobilities of the PATPV were 2.1 × 10^?3, 1.7 × 10^?2, and 1.1 × 10^?2 cm² V^?1 s^?1 on bare, octyltrichlorosilane (OTS)‐treated, and octadecyltrichlorosilane(ODTS)‐treated SiO₂, respectively, with on‐off current ratios of 35, 6.02 × 10², and 7.56 × 10². On the other hand, the estimated field‐effect transistor hole mobility of the PATPE was in the range of 1.7 × 10^?6–8.1 × 10^?4 cm² V^?1 s^?1, which was significantly smaller than those of the PATPV. The small band gaps and high charge carrier mobility of the prepared copolymers suggested their potential applications for near‐infrared electronic and optoelectronic devices. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 74–81, 2010     

Effect of thiophene spacers in benzodithiophene‐based polymers for organic electronics

Poly{2,6‐bis(thiophene‐2‐yl)‐4,8‐bis(5‐dodecylthiophen‐2‐yl)benzo[1,2‐b :4,5‐b' ]dithiophene} [poly(Th‐bDTBDT‐Th)] was successfully synthesized through Stille coupling polymerization. The addition of the thiophene spacer groups between the benzodithiophene units resulted in improved performance in optoelectronic devices. This was attributed to the reduced lamellae stacking distance in thin film with prominent π–π stacking peak indicating close assembly of poly(Th‐bDTBDT‐Th). Spacing between the benzodithiophene units in poly(Th‐bDTBDT‐Th) helped the close packing of dodecyl chains and generated improved π stacking interaction. For poly(Th‐bDTBDT‐Th), the measured average field effect mobility was 2.32 × 10^?3 cm² V^?1 s^?1 and average hole mobility in vertical direction was 2.92 × 10^?5 cm² V^?1 s^?1. Charge transport in both directions was improved by one order of magnitude with the presence of the thiophene spacer. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 3942–3948     

A Soluble Ladder‐Conjugated Star‐Shaped Oligomer Composed of Four Perylene Diimide Branches and a Fluorene Core: Synthesis and Properties

A new ladder‐conjugated star‐shaped oligomer electron‐transporting material TetraPDI‐PF , with four perylene diimide (PDI) branches and a fluorene core, was efficiently synthesized. The oligomer is highly soluble in dichlorobenzene with a solubility of 155 mg mL^?1, which is higher than those of PDI (35 mg mL^?1) and PDI‐Phen (70 mg mL^?1). Demonstrated by thermogravimetric analysis (TGA), the oligomer exhibits excellent thermal stability with the decomposition temperature (T_d) of 291.2 °C, which is 65 °C higher than that of PDI. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) were employed to investigate the electrochemical properties. Although the CV curves of TetraPDI‐PF are successively scanned for 15 cycles, they still remain invariable reduction potentials. The oligomer also shows outstanding photostability, even better than PDI, which maintains 99 % fluorescence intensity after irradiation for 10 min using maximum laser intensity. In the steady‐state space‐charge‐limited current (SCLC) devices, TetraPDI‐PF exhibits higher intrinsic electron mobility of 2.22×10^?5 cm² V^?1 s^?1, three orders of magnitude over that of PDI (3.52×10^?8 cm² V^?1 s^?1). The bulk heterojunction (BHJ) organic solar cells (OSCs) using TetraPDI‐PF as non‐fullerene acceptors and P3HT as donors give optimum power conversion efficiency (PCE) of 0.64 %, which is 64 times that of the PDI:P3HT BHJ cells.     

Bay‐annulated indigo based near‐infrared sensitive polymer for organic solar cells

A new conjugated polymer (PBAIIDTT) based on bay‐annulated indigo and indacenodithieno[3,2‐b]thiophene was designed, synthesized, and characterized. PBAIIDTT shows strong absorption in 400–500 and 600–800 nm, and its HOMO and LUMO energy levels are −5.45 eV and −3.65 eV, respectively. In organic field‐effect transistors, the polymer exhibits a relatively high hole mobility of 0.39 cm² V⁻¹ s⁻¹. PBAIIDTT was added to poly(3‐hexylthiophene) (P3HT) and phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) based organic solar cells. Ternary blend solar cells with 10% PBAIIDTT show an increased short circuit current density due to the broadened photocurrent generated in the near‐infrared region, and a power conversion efficiency of 3.78%, which is higher than that of the P3HT:PC₆₁BM binary control devices (3.33%). © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 213–220